Generac Power Systems 14 kW LP Installation Manuallines

Installation Guidelines

Air-cooled Generators

Eaton Generator Support 1-800-975-8331

TABLE OF CONTENTS

Introduction .........................................................Inside Front Cover

Read this Manual Thoroughly ..............................................IFC

Contents ................................................................................1

Operation and Maintenance ....................................................1

How to Obtain Service ............................................................1

Safety Rules ...................................................................................1

Standards Index .....................................................................3

Unpacking/Inspection .....................................................................3

NEC Requirement for Arc Fault Circuit Interruption

Breaker for Bedrooms .................................................................3

Section 210.12 Arc Fault Circuit Interrupter Protection ............3

Emission Information .....................................................................4

Before You Begin ............................................................................4

Site Preparation and Generator Placement ......................................4

Coverting to LP Vapor ....................................................................5

Installing & Connecting Gas Lines ..................................................6

External Electrical Connections .......................................................7

Generator Activation .......................................................................8

Generator Connections - Transfer Switch ........................................8

Appendix A - Setting the Automatic Exercise Function ...................10

Notes ..........................................................................................11

Installation Diagrams ..................................................................12

Electrical Data ............................................................................14

GUÍAS DE INSTALACIÓN ....................................27

CONSIGNES D’INSTALLATION ...............................41

INTRODUCTION

Thank you for purchasing this compact, high performance, air-

cooled, engine-driven generator. It is designed to automatically

supply electrical power to operate critical loads during a utility

power failure.

This unit is factory installed in an all-weather, metal enclosure that

is intended exclusively for outdoor installation. This generator

will operate using either vapor withdrawn liquid propane (LP) or

natural gas (NG).

NOTE:

This generator is suitable for supplying typical

residential loads such as Induction Motors (sump

pumps, refrigerators, air conditioners, furnaces, etc.),

Electronic Components (computer, monitor, TV, etc.),

Lighting Loads and Microwaves.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the

nearest Dealer for starting, operating and servicing procedures.

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a

procedure and will be found within the regular text

body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety information that,

if not followed, could endanger personal safety and/or

property of others.

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects

and other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNING

This product contains or emits chemicals known to the

State of California to cause cancer, birth defects and

other reproductive harm.

Table of Contents

1





This symbol points out potential explosion hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical shock hazard.

The operator is responsible for proper and safe use of the

equipment. The manufacturer strongly recommends that the

operator read this Owner’s Manual and thoroughly understand all

instructions before using this equipment. The manufacturer also

strongly recommends instructing other users to properly start and

operate the unit. This prepares them if they need to operate the

equipment in an emergency.

CONTENTS

This manual contains pertinent owner’s information for these

models:

• 7 kW NG, 8 kW LP, single-cylinder GH-410 Engine

• 9 kW NG, 10 kW LP, V-twin GT-530 Engine

• 13 kW NG, 14 kW LP, V-twin GT-990 Engine

• 16 kW NG, 17 kW LP, V-twin GT-990 Engine

• 18 kW NG, 20 kW LP, V-twin GT-999 Engine

OPERATION AND MAINTENANCE

It is the operator’s responsibility to perform all safety checks, to

make sure that all maintenance for safe operation is performed

promptly, and to have the equipment checked periodically by a

Dealer. Normal maintenance service and replacement of parts

are the responsibility of the owner/operator and, as such, are not

considered defects in materials or workmanship within the terms

of the warranty. Individual operating habits and usage contribute to

the need for maintenance service.

Proper maintenance and care of the generator ensures a minimum

number of problems and keep operating expenses at a minimum.

See a Dealer for service aids and accessories.

HOW TO OBTAIN SERVICE

When the generator requires servicing or repairs, contact a Dealer

for assistance. Service technicians are factory-trained and are

capable of handling all service needs. For assistance locating a

dealer, call 888-436-3722.

When contacting a Dealer about parts and service, always supply

the complete model number and serial number of the unit as given

on its data decal, which is located on the generator. See section

“The Generator” for decal location.

Model No.__________________ Serial No. ______________

SAFETY RULES



Save These Instructions – The manufacturer

suggests that these rules for safe operation be

copied and posted near the unit’s installation

site. Safety should be stressed to all operators

and potential operators of this equipment.

Study these SAFETY RULES carefully before installing, operating

or servicing this equipment. Become familiar with this Owner’s

Manual and with the unit. The generator can operate safely,

efficiently and reliably only if it is properly installed, operated and

maintained. Many accidents are caused by failing to follow simple

and fundamental rules or precautions.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all-inclusive.

If using a procedure, work method or operating technique the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.



Despite the safe design of this generator,

operating this equipment imprudently, neglect-

ing its maintenance or being careless can

cause possible injury or death. Permit only

responsible and capable persons to install,

operate and maintain this equipment.



Potentially lethal voltages are generated by

these machines. Ensure all steps are taken to

render the machine safe before attempting to

work on the generator.



Parts of the generator are rotating and/or hot

during operation. Exercise care near running

generators.



Installation must always comply with applicable

codes, standards, laws and regulations.



A running generator gives off carbon monoxide,

an odorless, colorless poison gas. Breathing

in carbon monoxide can cause headaches,

fatigue, diziness, nausea, vomitting, confusion,

fainting, siezures or death.

Safety Rules

2

GENERAL HAZARDS

• For safety reasons, the manufacturer recommends that this equipment

be installed, serviced and repaired by a Service Dealer or other

competent, qualified electrician or installation technician who is familiar

with applicable codes, standards and regulations. The operator also

must comply with all such codes, standards and regulations.

• The engine exhaust fumes contain carbon monoxide, which

can be DEADLY. This dangerous gas, if breathed in sufficient

concentrations, can cause unconsciousness or even death. Do

NOT alter or add to the exhaust system or do anything that might

render the system unsafe or in noncompliance with applicable

codes and standards.

• Install a battery operated carbon monoxide alarm indoors,

according to manufacturer’s instructions/recommendations.

• Adequate, unobstructed flow of cooling and ventilating air is

critical to correct generator operation. Do not alter the installation

or permit even partial blockage of ventilation provisions, as this

can seriously affect safe operation of the generator. The generator

MUST be installed and operated outdoors only.

• Keep hands, feet, clothing, etc., away from drive belts, fans, and

other moving or hot parts. Never remove any drive belt or fan

guard while the unit is operating.

• When working on this equipment, remain alert at all times. Never

work on the equipment when physically or mentally fatigued.

• Inspect the generator regularly, and contact the nearest Dealer for

parts needing repair or replacement.

• Before performing any maintenance on the generator, disconnect

its battery cables to prevent accidental start up. Disconnect the

cable from the battery post indicated by a NEGATIVE, NEG or

(–) first, then remove the POSITIVE, POS or (+) cable. When

reconnecting the cables, connect the POSITIVE cable first, the

NEGATIVE cable last.

• Never use the generator or any of its parts as a step. Stepping on

the unit can stress and break parts, and may result in dangerous

operating conditions from leaking exhaust gases, fuel leakage, oil

leakage, etc.

ELECTRICAL HAZARDS

• All generators covered by this manual produce dangerous electrical

voltages and can cause fatal electrical shock. Utility power delivers

extremely high and dangerous voltages to the transfer switch as

does the standby generator when it is in operation. Avoid contact

with bare wires, terminals, connections, etc., while the unit is

running. Ensure all appropriate covers, guards and barriers are

in place, secured and/or locked before operating the generator.

If work must be done around an operating unit, stand on an

insulated, dry surface to reduce shock hazard.

• Do not handle any kind of electrical device while standing in water,

while barefoot, or while hands or feet are wet. DANGEROUS

ELECTRICAL SHOCK MAY RESULT.

• The National Electrical Code (NEC) requires the frame and external

electrically conductive parts of the generator to be connected to an

approved earth ground. Local electrical codes also may require proper

grounding of the generator electrical system.

• After installing this home standby electrical system, the generator

may crank and start at any time without warning. When this

occurs, load circuits are transferred to the STANDBY (generator)

power source. To prevent possible injury if such a start and

transfer occur, always set the generator’s AUTO/OFF/MANUAL

switch to its OFF position before working on equipment and

remove the 15A fuse from the generator control panel.

• In case of accident caused by electric shock, immediately shut down

the source of electrical power. If this is not possible, attempt to free

the victim from the live conductor. AVOID DIRECT CONTACT WITH

THE VICTIM. Use a nonconducting implement, such as a dry rope

or board, to free the victim from the live conductor. If the victim is

unconscious, apply first aid and get immediate medical help.

• Never wear jewelry when working on this equipment. Jewelry can

conduct electricity resulting in electric shock, or may get caught in

moving components causing injury.

FIRE HAZARDS

• For fire safety, the generator must be installed and maintained

properly. Installation must always comply with applicable

codes, standards, laws and regulations. Adhere strictly to local,

state and national electrical and building codes. Comply with

regulations the Occupational Safety and Health Administration

(OSHA) has established. Also, ensure that the generator is

installed in accordance with the manufacturer’s instructions and

recommendations. Following proper installation, do nothing that

might alter a safe installation and render the unit in noncompliance

with the aforementioned codes, standards, laws and regulations.

• Keep a fire extinguisher near the generator at all times.

Extinguishers rated “ABC” by the National Fire Protection

Association are appropriate for use on the standby electric system.

Keep the extinguisher properly charged and be familiar with its use.

Consult the local fire department with any questions pertaining to

fire extinguishers.

EXPLOSION HAZARDS

• Do not smoke around the generator. Wipe up any fuel or oil spills

immediately. Ensure that no combustible materials are left in the

generator compartment, or on or near the generator, as FIRE or

EXPLOSION may result. Keep the area surrounding the generator

clean and free from debris.

• Gaseous fluids such as natural gas and liquid propane (LP)

gas are extremely EXPLOSIVE. Install the fuel supply system

according to applicable fuel-gas codes. Before placing the home

standby electric system into service, fuel system lines must be

properly purged and leak tested according to applicable code.

After installation, inspect the fuel system periodically for leaks. No

leakage is permitted.

Safety Rules

3

ENGINE EXHAUST HAZARDS

• Generator engine exhaust contains DEADLY carbon monoxide, an

odorless, colorless poisonous gas. Breathing carbon monoxide

can cause: dizziness, throbbing temples, nausea, muscular

twitching, headache, vomiting, weakness and sleepiness, inability

to think clearly, fainting, unconsciousness or even death. If you

experience any carbon monoxide poisoning symptoms, move into

fresh air and immediately seek medical attention.

• Never operate the generator set with the generator inside any

garage or other enclosed area EVEN IF doors and windows are

open.

STANDARDS INDEX

In the absence of pertinent standards, codes, regulations and laws,

the published information listed below may be used for installation

guidance for this equipment.

1. NFPA No. 37, STATIONARY COMBUSTION ENGINES AND

GAS TURBINES, available from the National Fire Protection

Association, 470 Atlantic Avenue, Boston, MA 02210.

2. NFPA No. 76A, ESSENTIAL ELECTRICAL SYSTEMS FOR HEALTH

CARE FACILITIES, available same as Item 1.

3. NFPA No. 54, NATIONAL FUEL GAS CODE, available same as

Item 1.

4. NFPA No. 58, AMERICAN NATIONAL STANDARD FOR STORAGE

AND HANDLING OF LIQUEFIED PETROLEUM GAS, available

same as Item 1.

5. NFPA No. 70, NFPA HANDBOOK OF NATIONAL ELECTRIC CODE,

available same as Item 1.

6. Article X, NATIONAL BUILDING CODE, available from the

American Insurance Association, 85 John Street, New York, N.Y.

10038.

7. AGRICULTURAL WIRING HANDBOOK, available from the Food

and Energy Council, 909 University Avenue, Columbia, MO

65201.

8. ASAE EP-3634, INSTALLATION AND MAINTENANCE OF FARM

STANDBY ELECTRICAL SYSTEMS, available from the American

Society of Agricultural Engineers, 2950 Niles Road, St. Joseph,

MI 49085.

9. NFPA No. 30, FLAMMABLE AND COMBUSTIBLE LIQUIDS CODE,

available same as Item 1.



Only qualified electricians or contractors should

attempt such installations, which must comply

strictly with applicable codes, standards and

regulations.

UNPACKING/INSPECTION

After unpacking, carefully inspect the contents for damage.

• This standby generator set is ready for installation with a factory

supplied and pre-mounted base pad and has a weather protective

enclosure that is intended for outdoor installation only.

• This UL listed, 2-pole switch is rated at 100 or 200 AC amperes at

250 volts maximum. The 100 Amp transfer switch is for indoor

use only. The 200 Amp transfer switch is for indoor/outdoor use

(if equipped).



If this generator is used to power electrical load

circuits normally powered by a utility power

source, it is required by code to install a transfer

switch. The transfer switch must effectively isolate

the electrical system from the utility distribution

system when the generator is operating (NEC 700,

701 & 702). Failure to isolate an electrical system

by such means will result in damage to the gen-

erator and also may result in injury or death to

utility power workers due to backfeed of electrical

energy.

If any loss or damage is noted at time of delivery, have the person(s)

making the delivery note all damage on the freight bill or affix their

signature under the consignor’s memo of loss or damage.

If a loss or damage is noted after delivery, separate the damaged

materials and contact the carrier for claim procedures.

“Concealed damage” is understood to mean damage to the contents

of a package that is not in evidence at the time of delivery, but is

discovered later.

To properly open the roof, press down on the center top lip and

release the latch. If pressure is not applied from the top, the roof may

appear stuck. Always verify that the side lock is unlocked before

attempting to lift the roof.

NEC REQUIREMENTS

Local code enforcement may require that AFCI’s be incorporated

into the transfer switch distribution panel. The Transfer Switch

provided with this generator has a distribution panel that will

accept AFCI’s.

Siemens Part No. Q115AF - 15A or Q120AF - 20A can be

obtained from a local electrical wholesaler and will simply replace

any of the single pole circuit breakers supplied in the Transfer

Switch distribution panel.

Eaton Cat # Description

BR115AF 1” 15A Single Pole AFCI

CH115AF 3/4” 15A Single Pole AFCI

BR120AF 1” 20A Single Pole AFCI

CH120AF 3/4” 20A Single Pole AFCI

General Information

4

EMISSION INFORMATION

The Environmental Protection Agency requires that this generator

complies with exhaust emission standards. This generator is

certified to meet the applicable EPA emission levels. Additional

information regarding the requirements set by the EPA is as

follows:

The generator is certified for use as a stationary engine for

standby power generation. Any other use may be a violation

of federal and/or local laws. It is important that to follow the

maintenance specifications in the “Maintenance” section to

ensure that the engine complies with the applicable emission

standards for the duration of the engine’s life. This engine is

certified to operate on Liquid Propane fuel and pipeline Natural

Gas. The emission control system on the generator consists of

the following:

• Fuel Metering System

• Carburetor/mixer assembly

• Fuel regulator

• Air Induction System

• Intake pipe/manifold

• Air cleaner

• Ignition System

• Spark plug

• Ignition module

The Emissions Compliance Period referred to on the Emissions

Compliance Label indicates the number of operating hours for

which the engine has been shown to meet Federal emission

requirements. See the table below to determine the compliance

period for the generator. The displacement of the generator is

listed on the Emissions Compliance Label.

Displacement Category Compliance Period

< 66 cc

A 300 Hours

B 125 Hours

C 50 Hours

 66 cc -

< 225 cc

A 500 Hours

B 250 Hours

C 125 Hours

 225 cc

A 1000 Hours

B 500 Hours

C 250 Hours

BEFORE YOU BEGIN

Contact the local inspector or City Hall to be aware of all federal,

state and local codes that could impact the installation. Secure all

required permits before starting the job.

Carefully read and follow all of the procedures and safety

precautions detailed in the installation guide. If any portion of the

installation manual, technical manual or other factory-supplied

documents is not completely understood, contact a dealer for

assistance.

Fully comply with all relevant NEC, NFPA and OSHA standards

as well as all federal, state and local building and electric codes.

As with any generator, this unit must be installed in accordance

with current NFPA 37 and NFPA 70 standards as well as any other

federal, state, and local codes for minimum distances from other

structures.

SITE PREPARATION AND GENERATOR

PLACEMENT

1. Locate the mounting area as close as possible to the transfer

switch and fuel supply.

Leave adequate room around the area for service access

(check local code), and place high enough to keep rising

water from reaching the generator.

Choose an open space that will provide adequate and

unobstructed airflow (see the “Location” section in the

Owner’s Manual).

General Information

5

2. Place the unit so air vents won’t become clogged with leaves,

grass, snow or debris. Make sure exhaust fumes will not enter

the building through eaves, windows, ventilation fans or other

air intakes.

Refer to the local codes and standards for the proper distance

between the unit and the building/structure.

Dig a rectangular area approximately five inches deep and

about six inches longer and wider than the footprint of the

generator. Cover with polyurethane film and fill with pea gravel

or crushed stone. Compact and level the stone. A concrete

pad can be poured if desired.

3. Inspect the generator for shipping damage and if necessary,

file a claim with the shipper.

Remove the bands holding the generator to the wooden pallet.

4. Make sure the lifting equipment to be used has sufficient

capacity to safely handle the weight of the generator.

Use nylon lifting straps and connect them to the lifting eyes

on each corner of the base frame to avoid damaging the

enclosure.

5. Set the generator onto the pad so that the gravel bed extends

several inches beyond the generator on all sides.

Make sure the generator is level within ½ inch.

6. Connect an approved ground strap to the grounding lug on the

base frame and to an approved earth ground or grounding rod

as specified by local regulations.

7. Check the engine oil and, if necessary, add enough of the

recommended oil to bring the level up to the FULL mark on

the dipstick. Be careful not to overfill the crankcase.

CONVERTING TO LP VAPOR

1. The generator was configured for natural gas operation at the

factory. Switching over to LP Vapor is a simple procedure.

On models with a single cylinder engine, begin by

disconnecting and removing the battery if installed.

General Information

6

2. Take the plastic T-handle fuel selector in the poly bag supplied

with the generator and locate the selector tab on the air box

cover. Insert the pin end into the hole in the selector tab

and pull outward to overcome spring pressure. Then twist

clockwise 90 degrees and allow the selector to return in once

aligned with the LP position.

3. On 10 kW units, open the roof, loosen the forward clamp

on the air inlet hose, and slide the hose away from the hose

fitting.

4. Slide the fuel selector pin on the carburetor out towards the

back of the enclosure.

5. Replace the inlet hose and tighten the clamp securely.

6. On all other models, simply remove the air cleaner cover and

slide the fuel selector pin outward from the natural gas to the

LP position.

INSTALLING & CONNECTING GAS LINES

1. Both natural gas and LP Vapor are highly volatile substances,

so strict adherence to all safety procedures, codes, standards

and regulations is essential.

Gas line connections should be made by a certified plumber

familiar with local codes. Always use AGA-approved gas pipe

and a quality pipe sealant or joint compound.

Verify the capacity of the natural gas meter or the LP tank in

regards to providing sufficient fuel for both the generator and

other operating appliances.

2. Most applications will require an external manual shutoff valve

on the fuel line.

General Information

7

3. Where the gas line is to enter the generator, install a T-fitting

to allow for gas pressure monitoring. On one opening of the

fitting install a ¼” NPT nipple and threaded plug. In some

cases a sediment trap may also be installed.

4. When connecting the gas line to the generator, use the

provided section of UL Listed or AGA-approved flexible fuel

line in accordance with local regulations. The purpose of the

flexible fuel line is to ensure that vibration from the generator

does not cause a gas leak at one of the connection points, so

it’s important that the line be installed with as few bends as

possible.

5. Never bend the flexible fuel line to avoid using an elbow.

Bending the flexible line decreases its ability to absorb

vibrations and defeats its purpose as well as constricts the

actual fuel flow.

6. After checking for leaks, check the gas pressure at the

T-fitting installed earlier to make sure there’s enough pressure

for proper generator operation.

The local gas supplier is responsible for ensuring adequate

pressure, so if the pressure is too low, or if it’s greater than

14 inches of water column, contact the gas supplier.

7. When finished checking the gas pressure, close the manual

shutoff valve.

EXTERNAL ELECTRICAL CONNECTIONS

1. Drill a 1 ¾ inch hole and feed the conduit through the hole.

General Information

8

2. Remove the knockout in the back of the connection box (if

used), feed the wires through the back of the box and secure

the conduit with the lock nut.

Seal the hole with silicone caulk. Don’t forget to caulk the hole

inside the house as well.

3. Mount the connection box (if used) so that it completely covers the

hole in the wall. Caulk around the sides and top of the box to ensure

a good seal.

Connect all wires to the lugs in the connection box (black to black,

red to red and white to white). Attach the green ground wire to

the ground screw and connect the two small plugs to their mating

receptacle ends.

4. Replace the protective cover plate and retaining screw, and

lock the connection box.

5. For 10-20 kW models, locate the metal hasp that is packaged

in the owner’s manual bag. Insert the hasp in the slot located

on the left side of the external circuit breaker box. Be sure that

the clip of the hasp is facing toward the front of the generator.

If desired, lock the external box.

GENERATOR ACTIVATION

When battery power is applied to the generator during the

installation process, the controller will light up. However, the

generator still needs to be activated before it will automatically run

in the event of a power outage.

Activating the generator is a simple one time process that is

guided by the controller screen prompts. Once the product is

activated, the controller screen will not prompt you again, even if

you disconnect the generator battery.

After obtaining your activation code, please complete the following

steps at the generator’s control panel in the Activation Chart

(shown on the following page).

GENERATOR CONNECTIONS – TRANSFER

SWITCH

1. If the Load Center transfer switch was purchased separately

from the generator it will need to be connected to the

generator. To complete the wiring, run power leads and

control wires from the transfer switch to the generator.

2. Remove the two screws securing the connection area cover,

and remove the cover.

4. Feed the wires through the back of the generator and secure

the conduit with the lock nut.

5. Run the power leads through the strain relief provided.

6. The circuit breaker is attached to the exterior access panel.

General Information

9

ACTIVATION CHART

CHOOSE LANGUAGE TROUBLESHOOTING

Display Reads: Use ARROW keys to scroll to desired

language. Press ENTER to select.

If the wrong language is chosen, it can be

changed later using the “edit” menu.

Display Reads: Press ENTER to begin the activation process. If ESCAPE is pressed instead of ENTER, your

generator will only run in manual mode (for

test purposes) and NOT ACTIVATED will be

displayed. You will need to reconnect the

battery and begin with Step 1.

Display Reads: If you do not have your activation code,

go to www.activategen.com or call

1-888-9ACTIVATE (922-8482).

If you already have your activation code, wait

3-5 seconds for the next display.

ENTER ACTIVATION CODE (Passcode) TROUBLESHOOTING

Display Reads: Use ARROW keys to scroll and find the first

number of your Activation Code.

Press ENTER to select.

Repeat this step until all digits have been

entered.

Use ESCAPE to correct previous digits.

Display Reads: Activation is complete when all digits are

entered above and your screen shows this

display.

Follow the controller prompts to continue

setting the time function. Refer to your

Owner’s Manual with questions.

What happens if “Wrong Passcode Try

Again” appears?

Reenter the activation code. If a second

attempt is unsuccessful, check the number

against the code given on activategen.com. If

it is correct and the generator will not accept

it, contact 1-888-9ACTIVATE (922-8482).

“SELECT HOUR (0-23)”

“- +”6

Escape Enter

Serial 123456789

Passcode XXXXX +/-

Escape Enter

To Activate go to

www.activategen.com

Escape Enter

Activate me (ENT) or

ESC to run in manual

Escape Enter

Language

- English +

Escape Enter

General Information

10

7. Remove the plastic plugs inside the main breaker access area

to allow connection of the power leads to the circuit breaker.

8. Now connect the red and black power leads to the circuit

breaker. Since this is a single-phase application, it doesn’t

matter which wire is connected to which lug.

9. Connect the green equipment ground wire to the ground bus

bar and torque to 35 inch lbs. The torque values are:

• 10-14 AWG = 35 in/lbs

• 8 AWG = 40 in/lbs

• 4-6 AWG = 45 in/lbs

10. Connect the white neutral wire to the neutral bus bar and

torque to 35 inch lbs. The torque values are:

• 10-14 AWG = 35 in/lbs

• 8 AWG = 40 in/lbs

• 4-6 AWG = 45 in/lbs

11. Connect the control wires to the correct terminals. The

terminals are clearly marked N1, N2 and T1.

NOTE:

In order to maintain separation of circuits, the

DC control wires must be separated from the AC

control wires. A piece of fiberglass sleeving has

been provided in the manual kit to achieve this.

Slide the sleeving over the AC wires OR the DC

wires, but not both, from the wire landing area

to the outside of the generator. Use the cable tie

locations to hold the sleeving in place.

12. An improperly connected control wire can damage the

generator control board.

T1

N2

N1

209

210

0

194

23

NEUT

GND

12. An improperly connected control wire can damage the

generator control board.

APPENDIX A - SETTING THE AUTOMATIC

EXERCISE FUNCTION

2. The display will enter an Installation Assistant mode when battery

power is first connected. The assistant will prompt to first enter

the current date and time, followed by the exercise day and time.

If the battery is ever disconnected and reconnected, or fuse

removed and replaced, the Installation Assistant will be displayed

again, but only the current date and time will need to be entered.

3. If the exercise time or day ever needs to be changed, press

the escape key to access the main menu.

4. Press the left or right arrow key until ‘Edit’ is flashing and press

enter.

5. Press the right or left arrow key until the exercise time is

displayed and press enter.

6. Using the arrow and enter keys first set the exercise hour in

24 hour format, followed by the minute, and finally the day.

7. Once set, the generator will exercise each week at the same

time. Be sure to show the owners how to set the exercise

function for the day and time they want the unit to exercise.

8. If the generator is equipped with the low speed exercise feature,

it was enabled at the factory and no adjustment is needed.

Every installation has its own unique set of circumstances

and requirements. This booklet provides guidelines for basic

installations only and is not intended to cover all applications.

If there are any questions or concerns after carefully reading all

documentation received with the equipment, contact the nearest

dealer for assistance.

Neutral

Ground

Cable Tie Location

Appendix A

11

Notes

12

Installation Diagram Drawing No. 0H8947-A

13

Drawing No. 0H8947-A Installation Diagram

14

Electrical Data Wiring Diagram - 8kW - Drawing No. 0H6912-B

15

Wiring Diagram - 8kW - Drawing No. 0H6912-B Electrical Data

16

Electrical Data Wiring Diagram - 8kW - Drawing No. 0H6912-B

17

Wiring Diagram - 10-14kW - Drawing No. 0H7358-B Electrical Data

18

Electrical Data Wiring Diagram - 10-14kW - Drawing No. 0H7358-B

La page charge ...

Generac Power Systems 14 kW LP Installation Manuallines

Generac Power Systems 14 kW LP Installation Manuallines

dans d''autres langues

Autres documents