Jacobsen 10029628 Maintenance Manual

Catégorie
Tondeuses à gazon
Taper
Maintenance Manual

Ce manuel convient également à

FR
AR Series Mower / Tondeuse série AR
10029628 - AR730 T4F
Series / Série : BAM
10029629 - AR730 Stage V
Series / Série : BAN
Kubota® V2403-T-E4B T4F/V2403-CR-TE5B-TXN-1
4WD / 4 RM
Reversing Fan / Ventilateur à inversion de marche
673834-B-FR
RJL AFCB
Safety Operation and Maintenance Manual
Manuel de sécurité, de fonctionnement et de maintenance
AVERTISSEMENT : Risque de blessures graves en cas d’utilisation incorrecte de la tondeuse. Les opérateurs et
le personnel d’entretien doivent être formés et conscients des dangers encourus. Ils doivent lire le manuel dans
son intégralité avant d’essayer de monter, d’utiliser, de régler ou d’entretenir la tondeuse.
AVERTISSEMENT
WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this
machine must be trained in its proper use, warned of its dangers and must read the entire manual before
attempting to set up, operate, adjust or service the machine.
WARNING
1 CONTENTS
en-1
1Contents
FOREWORD
This manual contains adjustment, maintenance, and
troubleshooting instructions for your new Jacobsen
machine. This manual should be stored with the
equipment for reference during operation.
Before you operate your machine, you and each operator
you employ should read the manual carefully in its
entirety. By following the safety, operating and
maintenance instructions, you will prolong the life of your
equipment and maintain its maximum efficiency.
If additional information is needed, contact your
Jacobsen Dealer.
SERVICE SUPPORT MATERIAL
Part No. Description
673834Safety, Operation & Maintenance Manual
673837Parts Manual
4299117 Kubota V2403-T-E4B Engine Parts Manual
689336 Kubota V2403-CR-TE5B Engine Parts Manual
Part No. Description
© 2020 Textron Specialized Vehicles
This manual may not re reproduced in whole or in part without the express permission of TSV Technical Communications Department.
09-2020
CALIFORNIA PROPOSITION 65
WARNING
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
!
Blade Recommendations
AR730 - 23” BLADE RECOMMENDATION
DISCHARGE MODE MULCH MODE COMMENTS
Vortex Combo Best cut quality; good distribution
Good hiding of clippings for cool and warm
season grasses; best quality cut
Best all around blade in cool and warm
season grasses
692774 Good all around blade Sometimes best blade for Bermuda
Extreme Mulch
In certain conditions best distribution, but
some degradation in cut quality
Best blade for hiding, but some degrada-
tion in cut quality
Performance is very dependent on spe-
cific local conditions
692775 Often the best blade for Bermuda Often the best blade for Bermuda
High Lift Use for very heavy conditions Not recommended Not Available for European Market
692771 Helps with distribution in cool season
grass, especially in the Spring Not recommended
Note: * These recommendations are intended as an initial guide for blade selection.
Grass type, regional climates, height of cut, and customer preferences will affect the actual blade choice.
** Due to sound level regulations, some blades may not be available in all regions. Please check with your local dealer for
availability.
TABLE OF CONTENTS
1
Contents
Introduction
1.1 Important.............................................................................2
1.2 Product Identification...........................................................3
1.3 Key Numbers ......................................................................3
1.4 parts manual .......................................................................3
1.5 Guidelines For The Disposal Of Scrap Products ................4
Safety
2.1 How to Operate Safely........................................................5
Labels
3.1 Safety Labels ....................................................................12
3.2 Instruction Labels..............................................................14
Controls
4.1 Operator Compartment .....................................................15
4.2 Control Panel ....................................................................16
4.3 Armrest Adjuster ...............................................................43
4.4 Traction Pedal...................................................................43
4.5 Steering Tilt Control ..........................................................43
4.6 Tow Valve .........................................................................44
4.7 Parking Brake Release Valve ...........................................44
Operation
5.1 Daily Inspection.................................................................45
5.2 Interlock System................................................................46
5.3 Operating Procedure.........................................................47
5.4 Starting The Engine ..........................................................48
5.5 To Stop The Engine ..........................................................48
5.6 Driving...............................................................................49
5.7 Traction Modes .................................................................49
5.8 Mowing Speed ..................................................................49
5.9 Mowing..............................................................................49
5.10 Mowing On Slopes..........................................................50
5.11 Towing The Mower..........................................................52
5.12 To Remove A Blockage From Cutting Implements .........53
5.13 SLINGING and jacking THE MACHINE..........................53
Adjustments
6.1 General Precautions .........................................................54
6.2 Alternator Belt ...................................................................54
6.3 Steering Shaft Adjustment ................................................55
6.4 Armrest Adjustment...........................................................55
6.5 Standard Seat Adjustments ..............................................56
6.6 Premium Seat Option Adjustments...................................56
6.7 Front Proximity Switch ......................................................57
6.8 Fine Adjustment ................................................................57
6.9 Height Of Cut ....................................................................58
6.10 Torque Specification .......................................................59
Maintenance and Lubrication
7.1 Maintenance And Lubrication Charts................................60
7.2 General Precautions .........................................................63
7.3 Engine...............................................................................63
7.4 Engine Lubrication ............................................................64
7.5 Engine Coolant .................................................................65
7.6 Hydraulic System ..............................................................67
7.7 Hydraulic Filter ..................................................................68
7.8 Hydraulic Hoses................................................................69
7.9 Fuel ...................................................................................70
7.10 Air Cleaner ......................................................................72
7.11 Charge The Battery.........................................................72
7.12 Battery.............................................................................73
7.13 Engine Exhaust...............................................................74
7.14 Tires ................................................................................74
7.15 Wheel Mounting Procedure ............................................75
7.16 Blade Change .................................................................75
7.17 Inspecting Blades............................................................76
7.18 Sharpening Blades..........................................................76
7.19 Folding ROPS.................................................................77
7.20 Care and Cleaning..........................................................78
7.21 Mower Storage................................................................79
Electrical System
8.1 General Information ..........................................................80
8.2 Fuse And Relay/Component identification........................80
Problem Solving
9.1 Engine Problem Solving....................................................82
Quality of Cut
10.1 Quality of Cut Problem Solving .......................................84
10.2 Washboarding.................................................................84
10.3 Step Cutting ....................................................................85
10.4 Scalping ..........................................................................86
10.5 Stragglers........................................................................87
10.6 Streaks............................................................................88
10.7 Windrowing .....................................................................89
10.8 Mismatched Cutting Implements.....................................90
Specifications
11.1 Engine Specification .......................................................91
11.2 Dimensions & Weights....................................................92
11.3 Machine Specification.....................................................94
11.4 Hydraulic Specification....................................................94
11.5 Vibration..........................................................................95
11.6 Noise...............................................................................96
11.7 Slopes.............................................................................96
11.8 Cutting Performance .......................................................96
11.9 Cutter Implement Specification.......................................96
11.10 Recommended Lubricants ............................................97
11.11 Accessories...................................................................97
1 INTRODUCTION
en-2
1Introduction
1.1 IMPORTANT ______________________________________________________________
The AR730 with a Diesel engine is a self propelled rotary mower with hydraulic systems to power the traction drive, the
cutting implement lift and lower, the cutting implement drives and the steering.
IMPORTANT: Do the maintenance indicated in this manual to make sure that the quality of cut is kept at a high level.
This Manual is part of the machine and must stay with the machine always. The suppliers of new, or used, machines
need to keep this documentation and supply the owners with a copy.
This equipment is intended for turf care and maintenance, primarily for grass cutting. Accessories approved by
Jacobsen may support alternate secondary functionality to allow more versatile use of the equipment.
Certifications of accessories for global regional use is subject to local regulations.
ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and
maintenance procedures.
Make sure that you obey all safety and road traffic regulations.
You must not make any changes to the machine that are not approved by the manufacturer. This type of change can
release the manufacturer from the liability for any damage or injury.
Discard worn parts in accordance with all local environment protection regulations. Use the local systems available in
the country where the machine is used, for these recycled materials. When the machine is at its end of life, there are
guidelines in this manual for the removal of the machine from use.
Use only Jacobsen Genuine spare parts to meet the machine type approval regulations specified by the European
Union.
2006/42/EC
These instructions are the Original instructions confirmed by Jacobsen
INTRODUCTION 1
en-3
1.2 PRODUCT IDENTIFICATION _________________________________________________
Mower Serial number plate
A. Maximum front axle load in Kg (for machines being driven on the
highway)
B. Unladen weight, (No cutting implements or fuel (mass) in Kg
C. Maximum rear axle load in Kg (for machines being driven on the
highway)
D. Power in Kw
E. Date code
F. Machine type (Designation)
G. Product code
H. Product name
J. Serial number
Location of Mower Serial number plate
The serial number plate (A) is found on the rear closeout.
Engine Identification
The engine serial number is found on the top of the valve cover toward
the front of the mower. The label shows the engine group and serial
number
The engine serial number is also found on the engine block.
1.3 KEY NUMBERS
Record the mower and the engine serial numbers.
The serial numbers are found on the serial plates and the engine serial
number is on the valve cover.
Machine Serial Number: . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Serial Number: . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 PARTS MANUAL
To refer to the parts list for this mower you have two options:
1. Website – www.jacobsen.com. Select the “ONLINE PARTS LOOK-UP” tab. These pages will show the parts list
and the line drawings you need to help with the identification of spare parts.
2. Website – www.jacobsen.com. Select the “MANUALS” tab. You have the option to view or “Download” a PDF
version of the parts manual.
Kg Kw
Kg Kg
West Road
Ransomes Europark
Ipswich IP3 9TT
England
ABCD E
FG
HJ
A
Rear
Closeout
Kg Kw
Kg Kg
West Road
Ransomes Europark
Ipswich IP3 9TT
England
ABCD E
FG
HJ
V2403
S/N KEAXXXXX
Contact KEA for Parts
MADE IN JAPAN
BB
1 INTRODUCTION
en-4
1.5 GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS _______________________
1.5.1 DURING SERVICE LIFE_____________________________________________________
All the used fluids and parts must be controlled as hazardous materials. Recommended procedures must be followed for their
safe removal.
If a fluid leak occurs, contain the spill to make sure that the leak does not flow into the ground or drainage system. Follow the
regulations in force to make sure that leaks are controlled.
The maintenance procedures in this manual make sure that the damage that the machine can cause in the local environment
is controlled.
When the machine completes its full service life, the following actions must be taken.
1.5.2 END OF SERVICE LIFE _____________________________________________________
These guidelines must be used with applicable Health, Safety and Environmental laws. Always use the approved local waste
disposal and agencies for recycled materials.
Park the machine in an applicable area to use all of the necessary lifting equipment.
Use correct tools and Personal Protective Equipment (PPE) and take instruction from the technical manuals
applicable to the machine.
Remove and store correctly
1. Batteries
2. Fuel
3. Engine coolant
4. Oils
Read the Technical Manual before you begin to disassemble the machine. Plan the disassembly, give
attention to parts that are in a state of mechanical pressure or contain stored energy e.g springs.
Items that continue to have a service life must be separated and returned to the local dealer.
Items that are worn must be separated into the material groups and removed according to the agencies for
the recycled materials that are available. Common examples.
• Steel
• Non ferrous metals
• Aluminum
• Brass
• Copper
• Plastic materials
• Identified
• Can be recycled
• Can not be recycled
• Not identified
• Rubber
• Electrical and Electronic Components
Some parts are not easily separated e.g. Hydraulic hoses. These materials must be added to the “General
discarded materials” area.
Do not burn discarded materials.
Change the machinery records to show that the machine is not in operation and is discarded. Supply this serial number to
The Jacobsen Warranty Department to close their records.
SAFETY 2
en-5
2Safety
2.1 HOW TO OPERATE SAFELY_______________________________________________________
2.1.1 SAFE OPERATION
a Read the Operator’s Manual and other training material. If the operator or technician can not read this manual,
the owner is responsible to describe this material to the operators and technicians. Manuals in additional
languages may be available on the Jacobsen or Ransomes Jacobsen website.
a Read all of the instructions for this mower carefully. Know the controls and the correct operation of the
equipment.
b Children or other people who do not understand these instructions must not use the mower. The local regulations
can limit the age of the operator.
c Never use a mower near bystanders, including children or animals.
d Remember that the operator or owner is responsible for accidents or hazards that occur to other people or their
property.
e Never carry passengers.
f Never allow anyone to operate or service the mower or its attachments without correct instructions.
g Do not operate equipment while tired, sick or after you use alcohol or drugs.
2.1.2 PREPARATION
a When you operate the mower, wear correct clothing, slip resistant work shoes or boots, work gloves, hard hat,
safety glasses and hearing protection. Long hair, loose clothing or jewelry can be caught in moving parts.
b Do not operate the equipment with the Interlock System disconnected or the system does not operate correctly.
Do not disconnect or prevent the operation of any switch.
c Never operate equipment that is not in correct order or without labels, guards, shields, deflectors or other
protective devices fastened.
d Inspect the mower before you operate the mower. Check the tire pressure, engine oil level, the radiator coolant
level and the air cleaner indicator. Fuel is flammable. Use caution when you add the fuel to the mower.
e Operate the mower in daylight or in good artificial light. Use caution when you operate the mower during bad
weather. Never operate the mower with lightning in the area.
f Inspect the area to select the accessories and attachments that are needed to correctly and safely do the job.
Only use parts, accessories and attachments approved by Jacobsen.
g Be careful of holes in the terrain and other hazards that are not visible.
h Inspect the area where the equipment is operated. Remove all objects you can find before you operate. Be
careful of obstructions above the ground (low tree limbs, electrical wires) and also underground obstacles
(sprinklers, pipes, tree roots). Enter a new area carefully. Look for possible hazards.
i Inspect the cutting system before you start the mower. Make sure the blades are free to rotate. When you rotate
one blade, other blades can rotate.
WARNING
EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.
Know the location and correct operation of controls. Operators without experience must receive instruction from a
person trained in the correct operation of the equipment before being allowed to operate the mower.
Only use parts, accessories and attachments approved by Jacobsen.
!
2 SAFETY
en-6
2.1.3 OPERATION
a Never operate the engine without enough ventilation or in an enclosed area. The carbon monoxide in the
exhaust fumes can increase to dangerous levels.
b Never carry passengers. Keep bystanders or animals away from the mower.
c Disengage all drives and engage the parking brake before you start the engine. Only start the engine with the
operator in the seat. Never start the engine with anyone standing near the mower.
d Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep your
hands and feet away from the cutting implements.
e Do not use on the slopes greater than the safe slope limit for the equipment.
f To guard against over turning or loss of control:
Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).
Do not start or stop suddenly on slopes.
Decrease the speed when you operate on slopes or when you must turn. Use caution when you change
direction. Turf condition can change the mower stability.
Use caution when you operate the mower near drop-offs, ditches or embankments.
Be careful of holes in the terrain and other hazards that are not visible.
g When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not operate
the cutting implements when you drive in the reverse direction.
h Use caution when you go near corners, trees or other objects that can prevent a clear view.
i Equipment must meet the current regulations to be driven on the public roads.
j Before you move across or operate on the paths or roads, turn off the mow switch, lift the mowers and travel at
decreased speed. Look for traffic.
k Stop the blades when the mower is on any surface that is not grass.
l Do not release the cut grass in the direction of bystanders or allow bystanders near the mower while in operation.
m Do not operate the mower with damaged guards or without safety devices in position.
n Do not change the engine governor setting or over-speed the engine. Never change or tamper with adjusters that
are closed with a seal for the engine speed control.
o Before you leave the operator compartment, for any reason:
Disengage all the drives and lower attachments to the ground.
Engage the parking brake.
Stop the engine and remove the key.
p When you hit an object or mower starts to cause the vibration that is not normal, inspect the mower for damage
and make repairs.
q Decrease the throttle setting before you stop the engine.
r Do not use this equipment for uses that the mower was not made for.
SAFETY 2
en-7
2.1.4 ROPS
a The ROPS is a safety device. Always use the seat belt when you operate a mower equipped with a ROPS. Make
sure the seat belt can be released quickly in an emergency.
b Only operate the mower with the ROPS in the folded position on flat and level surfaces when necessary. Do not
operate the mower with the ROPS in the folded position on slopes, near sharp edges or near water. There is no
roll over protection with the ROPS in the folded position.
c Check for clearance before you drive below objects. Do not contact tree branches, electrical wires or other
objects with the ROPS.
d Do not use the seat belt with the ROPS in the folded position.
e Inspect the ROPS for damage. Keep the ROPS hardware fastened.
f Do not weld, drill, change or bend the ROPS. Replace a damaged ROPS. Do not try to correct a damaged
ROPS.
g Do not remove the ROPS from the mower.
h Jacobsen must approve any changes to the ROPS.
2.1.5 SAFE HANDLING OF FUELS
a The fuel and the fuel vapors are flammable. Use caution when you add fuel to the mower. The fuel vapors can
cause an explosion.
b Never use containers that are not approved to keep or transfer fuel.
c Never keep the mower or fuel containers near an open flame or any device that can cause the ignition of fuel or
fuel vapors.
d Never fill the fuel containers inside a vehicle or on a truck or trailer with a plastic liner. Always put the fuel
container on the ground away from your vehicle before you fill the container.
e Refuel the mower before you start the engine. Never remove the fuel cap or add fuel to the mower when the
engine is in operation or while the engine is hot.
f Refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition.
g The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device to lock
the fuel nozzle in the open position.
h Do not over fill the fuel tank. Leave at least 1 inch (2.5 cm) below the filler neck.
i Always tighten the fuel tank cap and container cap after you add fuel.
j If the fuel spills on your clothing, change your clothing immediately.
2.1.6 MAINTENANCE AND STORAGE
a Before you clean, adjust or repair this equipment, push mow switch to the OFF position, lower the cutting
implement to the ground, engage the parking brake, stop the engine and remove the key.
b Make sure the mower is parked on a solid and level surface.
c Never work on a mower that is lifted only by a jack. Always use jack stands.
d Never allow anyone to service the mower or its attachments without correct instructions.
e When the mower is parked, put into storage or left without an operator, lower the cutting device unless a positive
mechanical lock is used.
f When you put the mower on a trailer or put the mower in storage, close the fuel valve. Do not keep fuel near
flames or drain the fuel inside a building.
2 SAFETY
en-8
g Disconnect the battery before you service the mower. Always disconnect the negative battery cable before the
positive battery cable. Always connect the positive battery cable before the negative battery cable.
h Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To
prevent an explosion, keep any device that can cause sparks or flames away from the battery.
i Disconnect the battery charger from the power supply before you connect or disconnect the battery charger to
the battery. Wear protective clothing and use insulated tools when you service the battery.
j Be careful and wear gloves when you check or service the cutting implement blades. Replace any damaged
blades, do not try to correct a damaged blade.
k Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in operation,
unless the adjustment needs the engine in operation.
l Carefully release the pressure from components with stored energy.
m To prevent injury from hot, high pressure oil, never use your hands to check for oil leaks. Use the paper or
cardboard to find leaks.
n The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your skin, a
doctor must remove the hydraulic fluid surgically within a few hours or gangrene can occur.
o When you service the hydraulic system, make sure the hydraulic fittings, tubes and hoses are tightened to the
correct torque. Make sure the hydraulic system is in good condition before you start the engine.
p Keep the mower and the engine clean.
q Allow the engine to become cool before storage and always remove the ignition key.
r Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.
s Replace worn or damaged parts for safety. Replace damaged or worn labels. Only use parts, accessories and
attachments approved by Jacobsen.
t To decrease the fire hazard, remove grass and other materials that burn from around the engine, muffler, battery
tray and fuel tank area.
u Disconnect the battery and controller connectors before you weld on this mower.
2.1.7 WHEN YOU PUT THE MOWER ON A TRAILER
a Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and be able to
carry the weight of the mower.
b Use a trailer with a full-width ramp to load or unload the mower.
c Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be sent
down and toward sides of trailer.
d Make sure that all latches are correctly fastened.
SAFETY 2
en-9
2.1.8 IMPORTANT SAFETY NOTES________________________________________________
This safety alert symbol gives a warning of possible hazards.
DANGER - Indicates a dangerous condition that WILL cause death or injury unless it is prevented.
WARNING - Indicates a dangerous condition that CAN cause death or injury unless it is prevented.
CAUTION - Indicates a dangerous condition that can cause injury and property damage unless it is prevented. The
label can indicate work procedures that are not safe.
NOTICE - Indicates a condition that can cause damage to the property unless it is prevented. The label can indicate
work procedures that are not safe.
Some illustrations in this manual show the shields, guards or plates, removed. Do not operate this equipment without
these devices correctly fastened in position.
WARNING
The Interlock System on this mower prevents the operation of the mower unless:
a The parking brake is engaged.
b The mow switch is in the OFF position.
c The traction pedal is in the Neutral position.
The system will stop the engine if the operator leaves the seat without:
a The parking brake engaged.
b The mow switch in the OFF position.
NEVER operate the mower unless the Interlock System operates correctly.
WARNING
1. Before you leave the operator position, for any reason:
a. Return the traction pedal to Neutral.
b. Disengage all drives.
c. Lower the mowers to the ground.
d. Engage the parking brake.
e. Stop the engine and remove the ignition key.
2. Keep your hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,
adjust or service the mower.
3. Keep persons and animals away from the area of operation.
4. Never carry passengers.
5. Never operate the equipment without a correctly fastened grass deflector in position.
!
!
2 SAFETY
en-10
By following all instructions in this manual, you increase the life of your machine and keep its maximum performance.
Adjustments and maintenance must always be done by an approved technician.
If additional information or if service is needed, contact your Authorized Jacobsen Dealer. Your Dealer knows the
current methods to service this equipment.
WARNING
Breathing diesel engine exhaust exposes you to chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
• Always start and operate the engine in a well-ventilated area.
• If in an enclosed area, vent the exhaust to the outside.
• Do not modify or tamper with the exhaust system
• Do not idle the engine except when necessary.
For more information go to
www.p65warnings.ca.gov/diesel
WARNING
To prevent injury from the hot oil at high pressure, do not use your hands to check for oil leaks. make sure that you
use paper or cardboard.
Release of hydraulic fluid at high pressure has enough force to enter through the skin. if the fluid enters through the
skin, the fluid must be surgically removed within hours by a specialist doctor or gangrene may result.
WARNING
When the machine is driven off-road, a seat belt must be worn at all times.
This warning is because a seat belt must be worn with a ROPS to follow the Machinery Directive,
2006/42/EC Sections 3.2.2, Seating & 3.4.3, Rollover. (ANSI B71.4-2012 section 20.7)
Jacobsen recommends that the owner/user of the machine completes a local risk assessment of the machine to find
any conditions that do not follow this rule. e.g. when you drive the machine next to water or on the highway.
WARNING
Explosive gases are released by batteries. The battery contains corrosive acid and supplies an electrical current that
is high enough to cause burn injuries to the body.
WARNING
You must not use this machine to tow other mowers or vehicles.
!
!
!
!
!
SAFETY 2
en-11
WARNING
Ear protection must be worn when you operate machines with an operator ear noise level of more than 85 db(a) leq.
WARNING
Vibration Exposure Limits
Exposure limits are calculated as a combination of the vibration level (magnitude) of the tool and the Daily Exposure
Time (Trigger Time). E.g. A product with 5m/s² vibration can be used up to 2 hours/day to reach the EAV and up to 8
hours/day to reach the ELV.
Exposure Action Value (EAV) - Daily vibration exposure A(8) = 2.5m/s²
Where daily vibration exposure A(8) is below 2.5m/s² the risk is relatively low and no action need be taken
Exposure Limit Value (ELV) - Daily Vibration Exposure A(8) = 5.0m/s²
If several tools are used the exposure values must be combined:
Total exposure is then the combined value of the activities
WARNING
Never mow if there is a risk of lightning or when you hear thunder. If you are in the middle of mowing, stop in a safe
place, turn off the engine and go inside a building.
CAUTION
When you do any welding on the machine, the battery, controller and display units must be disconnected before you
start. You must not open the controller. If the controller is opened, this can cancel all of the warranties and can cause
the failure of the machine.
CAUTION
Personal Protective Equipment (PPE), For example safety glasses, leather work shoes or boots, a hard hat, leather
work gloves and ear protection must be used after the owner/user completes a local risk assessment of the mower,
to prevent injury.
Training in all manual operations must be given by an approved person before the machine is used the first time.
!
!
!
!
!
3 LABELS
en-12
3Labels
3.1 SAFETY LABELS__________________________________________________________
A 4199140 Warning, hot surfaces. Do not touch with bare hand.
B 4181861 Warning, do not use start assist fluids.
C 4181862 Warning, do not remove the radiator cap when the radiator is hot.
D 4153197 Caution, do not pressure wash radiator or allow water to enter the air intake.
E 9114380 Warning, fasten seat belt when folding ROPS is in the raised position.
F 4181864 Warning, battery
G 4326710 Warning, do not operate on slopes greater than 15°. Read the manual
H 4311249 Warning, implement
Rotating blades. Keep your hands, feet and clothing away from cutting implements.
Warning, be careful of objects thrown by the cutting implements. When mower is in operation,
keep bystanders and animals away.
Read the manual. Do not allow anyone without training to use the mower.
Do not step on cutting implements.
J 4326718 Warning, mower
Read the manual. Do not allow anyone without training to use the mower.
Keep the shields in position and hardware fastened.
Keep your hands, feet and clothing away from moving parts.
Before you clean, adjust or repair this equipment, disengage all drives, engage the parking
brake and stop the engine.
Never carry passengers.
When mower is in operation, keep bystanders and animals away.
K 845027 To prevent injury when adjusting the height of cut, use caution to prevent your fingers being
pinched between moving and fixed parts of the cutting implement.
AB
C
D
E
F
4326718
G
H
4181861
4181862
STOP
4181864
15°+
4326710
JK
LABELS 3
en-13
L Warning - This structure’s protective capability may be impaired by structural damage, overturn, or alteration. If
any of these conditions occur, the structure must be replaced.
M Notice - Do not fold this ROPS if a canopy is attached. Damage to the mover hood could result.
N Always use the seat belt with the ROPS frame in the vertical and locked position. Never use the seat belt with the
ROPS in the folded position.
P Canadian EMC Decal
This structure's proctective
capability may be impaired
by structural damage,
overturn, or alteration.
If any of these conditions
occur, the structure must
be replaced.
!WARNING
557844
NOTICE
Do NOT fold this ROPS
if a canopy is attached.
Damage to the mower
hood could result.
LM
N
P
3 LABELS
en-14
3.2 INSTRUCTION LABELS
Description
A 4117468 105 dB Guaranteed Sound Power Level
B 4381826 Traction Pedal
C 692776 Front HOC, Right Wing Deck
D 675163 Rear HOC, Right Wing Deck, Left Wing Deck, Left Wing Deck, LH
105dB
LWA
A
B
CD
4381826
692776
19 mm 0.75 in 1
HK
25 mm 1.00 in 2
32 mm 1.25 in 3
38 mm 1.50 in 4
44 mm 1.75 in 5
51 mm 2.00 in 6
57 mm 2.25 in 7
64 mm 2.50 in 8
70 mm 2.75 in 9
76 mm 3.00 in 10
83 mm 3.25 in 11
89 mm 3.50 in 12
95 mm 3.75 in 13
102 mm 4.00 in 14
108 mm 4.25 in 15
114 mm 4.50 in 16
K
H
15 12
14
16 13 10
11
9
8
6
7
5
4
2
1
3
675163
19 mm 0.75 in 1
HK
25 mm 1.00 in 2
32 mm 1.25 in 3
38 mm 1.50 in 4
44 mm 1.75 in 5
51 mm 2.00 in 6
57 mm 2.25 in 7
64 mm 2.50 in 8
70 mm 2.75 in 9
76 mm 3.00 in 10
83 mm 3.25 in 11
89 mm 3.50 in 12
95 mm 3.75 in 13
102 mm 4.00 in 14
108 mm 4.25 in 15
114 mm 4.50 in 16
H
K
1
2
3
48
7
6
59
10
11
12 16
15
14
13
CONTROLS 4
en-15
4Controls
4.1 OPERATOR COMPARTMENT ________________________________________________
4.2
4.3
4.4
4.5
4.6
4.7
4.2 - Control Panel
4.3 - Armrest Adjuster
4.4 - Traction Pedal
4.5 - Steering Tilt Lever
4.6 - Tow Valve (Under Seat)
4.7 - Brake Valve (Under Floorboard)
4 CONTROLS
en-16
4.2 CONTROL PANEL _________________________________________________________
4.2.1 - Key Switch
4.2.2 - Parking Brake Switch
4.2.3 - Mow Switch
4.2.4 - Light Switch (Optional)
4.2.5 - Lift/Lower Joystick
4.2.6 - Visual Display
0.0 Hours
0.0 Hours
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
CONTROLS 4
en-17
4.2.1 KEY SWITCH _____________________________________________________________
Turn the key switch to the 'START' position to start the engine. When the engine
starts, release the key and allow to return automatically to the 'RUN' position.
To stop the engine, turn the key to the ‘OFF’ position.
NOTE. There can be a time delay before the engine starts, it depends on the
engine temperature while the glow plugs operate automatically.
4.2.2 PARK BRAKE SWITCH _____________________________________________________
Move the orange button back and press the front of the switch to engage the park brake.
When the engine is stopped, the parkbrake is applied with the switch in both the ON and OFF
position.
To release the park brake, press the rear of the switch.
The park brake icon is displayed on the visual display screen when engaged.
DO NOT apply the brake while the machine is in motion. The park brake will also auto-engage
when the transmission is in neutral & the machine is not in motion. When this function is active,
the brake will automatically release when transmission pedal is operated in order to drive forward or in reverse.
4.2.3 MOW SWITCH ____________________________________________________________
The mow switch engages cutter rotation.
To cut grass, push the front of the switch and move the joystick forward to lower the cutting
implements. When the switch is in the ON position, the red LED on the switch is illuminated.
When the mow switch is in the ON position, the mower traction will be in all wheel drive (AWD).
To stop the drive to the cutting implements, press the rear of the mow switch.
When the cutting implements are lifted or the operator leaves the seat, cutting implements
rotation is stopped.
4.2.4 LIGHT SWITCH____________________________________________________________
Turns the work lights ON and OFF.
Push the top of the switch to turn the lights ON.
Push the bottom of the switch to turn the lights OFF.
OFF
RUN
START
4 CONTROLS
en-18
4.2.5 LIFT/LOWER JOYSTICK ____________________________________________________
The lift/lower joystick controls the lift and lower operation of the cutting
implements. The lift/lower joystick operates in One-Touch or manual
mode. Push the lift/lower joystick to lower the cutting implements or pull
the lift/lower joystick to lift the cutting implements.
The One-Touch or manual mode is set on the display.
Manual Mode - When One-Touch is disabled, the cutting implements will
lift or lower only while the lift/lower joystick is pulled or pushed.
One-Touch Mode - With One-Touch enabled and the mow switch is in
the ON position,
To Lower - Push and release the lift/lower joystick once to lower the
cutting implements to the mid Cross Cut position, Push and release the
lift/lower joystick a Second time to lower the cutting implements to the
ground and start the blades.
To Raise - Pull and release the lift/lower joystick once to lift the cutting implements to the mid Cross Cut position.Pull
and release the lift/lower joystick a second time to completely lift the cutting implements and stop the blades.
Left Wing Button - Press the left wing button on the top of the joystick to enable the left wing cutting implement. The
light on the button will turn on and the joystick will control the lift and lower of the cutting implement. When the left wing
cutting implement is lowered, and the mower is moving, the cutting implement blades will start to turn
Press the left wing button a second time to disable the left wing cutting implement. The cutting implement will stop and
lift to the transport position.
Right Wing Button - Press the right wing button on the top of the joystick to enable the right wing cutting implement.
The light on the button will turn on and the joystick will control the lift and lower of the cutting implement. When the right
wing cutting implement is lowered, and the mower is moving, the cutting implement blades will start to turn
Press the right wing button a second time to disable the right wing cutting implement. The cutting implement will stop
and lift to the transport position.
To engage the cutting implements if they are already in the lowered position but disengaged, Press the Mow Switch to
On position, Push and release the Lift /Lower joystick once to engage the cutter blades.
4.2.6 VISUAL DISPLAY__________________________________________________________
The visual display is activated when the key switch is turned to the ‘RUN’ position.
Left Wing
Button Right Wing
Button
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215

Jacobsen 10029628 Maintenance Manual

Catégorie
Tondeuses à gazon
Taper
Maintenance Manual
Ce manuel convient également à

dans d''autres langues