Jacobsen 068021-E410 Maintenance Manual

RJL 100 December 2019

Safety, Operation & Maintenance Manual

Manuel de sécurité, d'utilisation et de maintenance

68021-E410 - AR331, Kubota® D1105-E5B-RNS-2, 3 RM

Séries ES

WARNING

WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this

machine must be trained in its proper use, warned of its dangers and must read the entire manual before

attempting to set up, operate, adjust or service the machine.

AVERTISSEMENT

AVERTISSEMENT : Risque de blessures graves en cas d’utilisation incorrecte de la machine. Les

opérateurs et le personnel d’entretien doivent être formés et conscients des dangers encourus. Ils doivent

lire attentivement l’intégralité du manuel avant de monter, d’utiliser, de régler ou d’entretenir la machine.

679459-FR (rev.1)

FR

France

1 CONTENTS

SECTION PAGE SECTION PAGE

INTRODUCTION

Important ...................................................................... 3

Product Identification ................................................... 4

Guidelines For The Disposal Of Scrap Products ......... 6

During Service Life ...................................................... 6

End Of Service Life ..................................................... 6

Parts Manual ............................................................... 7

Key Numbers ............................................................... 7

SAFETY INSTRUCTIONS

How To Operate Safely ................................................ 9

Safe Operation ............................................................ 9

Preparation .................................................................. 9

Operation .................................................................... 10

Rollover Protective Structure ...................................... 11

Safe Handling Of Fuels .............................................. 11

Maintenance And Storage .......................................... 12

When You Put The Mower On A Trailer ..................... 12

Important Safety Notes ............................................... 13

LABELS

Safety Labels EC ........................................................ 16

Instruction Labels EC ................................................. 18

CONTROLS

Operator Workstation ................................................. 20

Control Panel .............................................................. 21

Key Switch .................................................................. 22

Light Switch (Optional) ............................................... 22

Parking Brake Switch ................................................. 22

Mow Switch ................................................................ 22

Side Shift Switch ........................................................ 23

Lift Lower Joystick ...................................................... 23

Visual Display Unit ..................................................... 23

Start-up screen............................................................ 23

Warning Service Screen.............................................. 24

First Screen ................................................................ 24

Engine Start ................................................................ 25

The Engine Will Not Start ............................................ 25

Main Menu .................................................................. 25

Main Navigation .......................................................... 26

Language ................................................................... 26

Clock .......................................................................... 27

Display Settings .......................................................... 27

Vehicle Settings Menu ................................................ 28

Measurement Settings Menu ..................................... 28

Enter Pin...................................................................... 29

One Touch .................................................................. 30

Change Pin ................................................................. 30

Set Default Parameters .............................................. 31

Reset Service Hours .................................................. 32

Service Menu .............................................................. 32

Fault Log .................................................................... 33

Time Until Service ...................................................... 34

Vehicle Status ............................................................ 35

Input/output diagnostics (I/O Diagnostics) .................. 36

Connector J1 ............................................................... 36

Connector J2 .............................................................. 37

Connector J3 .............................................................. 37

Connector J4 .............................................................. 37

Connector J5 .............................................................. 38

Connector J6 .............................................................. 38

Warnings ..................................................................... 39

Warning - Oil Pressure Fault ...................................... 39

Warning - Clear Radiator Screens ............................. 39

Warning - Can Time Out ............................................ 40

Warning - Battery Fault .............................................. 40

Warning - Controller I/O Fault .................................... 40

Throttle Lever ............................................................. 41

Armrest Adjuster ......................................................... 41

Traction Pedal ............................................................ 41

Mow Speed Lever ...................................................... 42

Steering Tilt Control .................................................... 42

Power Outlet ............................................................... 42

Tow Valve.................................................................... 43

Parking Brake Release Valve ..................................... 43

Fuel Gauge ................................................................. 44

OPERATION

Daily Inspection .......................................................... 46

Operator Presence And Safety Interlock System ....... 47

Procedure For Operation ............................................ 48

To Fit The Cutting Units To The Machine .................. 49

Operation Of The Machine ......................................... 52

How To Start The Engine ........................................... 52

How To Drive .............................................................. 53

How To Mow .............................................................. 53

To Stop The Engine ................................................... 53

Transporting ............................................................... 54

Transporting On A Trailer Or Flatbed ......................... 54

Jacking Point .............................................................. 54

Mowing On Slopes ..................................................... 55

ADJUSTMENTS

General Precautions.................................................... 58

Traction Control .......................................................... 58

Weight Transfer Adjustment ....................................... 59

Engine: Fan Belt ......................................................... 59

Neutral Switch Adjustment ......................................... 60

Armrest Height Adjustment ......................................... 60

Traction Pedal Stops .................................................. 61

Cutting Unit Limit Switch ............................................. 61

Cutting Height Adjustment (Option - Quick

Release Pin) ............................................................... 62

Cutting Blade Change ................................................ 63

Seat (Milsco V-2853) .................................................. 64

Seat (Michigan V-5300) .............................................. 64

Torque Specification ................................................... 65

MAINTENANCE AND LUBRICATION

Maintenance And Lubrication Charts .......................... 66

Engine Lubrication ...................................................... 68

General Precautions.................................................... 69

Engine ........................................................................ 69

Engine Coolant ........................................................... 71

Engine: Fan Belt - Diesel ............................................ 72

Hydraulic Filter ............................................................ 73

Hydraulic System ........................................................ 73

Hydraulic Hoses ......................................................... 74

Fuel ............................................................................ 75

Replacing Fuel Filters ................................................. 76

Fuel System ............................................................... 76

Air Cleaner ................................................................. 77

Engine Exhaust .......................................................... 77

Cutting Unit 674381 Lubrication ................................. 78

Lubrication .................................................................. 78

Inspect Blades ............................................................ 79

Blade Sharpening ....................................................... 79

Battery ........................................................................ 80

Charging The Battery ................................................. 81

Tyres .......................................................................... 82

Wheel Mounting Procedure ........................................ 82

ROPS ......................................................................... 83

Care And Cleaning ..................................................... 84

Mower Storage ........................................................... 85

PROBLEM SOLVING

Engine Problem Diagnostics ...................................... 86

QUALITY OF CUT

Quality Of Cut Problem Solving .................................. 88

The Step Cut .............................................................. 89

Scalping ...................................................................... 90

Stragglers ................................................................... 91

Streaks ....................................................................... 92

Windrowing ................................................................. 93

Mismatched Cutter Decks .......................................... 94

FUSES AND RELAYS

Fuse And Relay/component Identification .................. 96

SPECIFICATIONS

Engine Specification ................................................... 99

Dimensions And Weights .......................................... 100

Machine Specification ............................................... 102

Vibration .................................................................... 103

Noise ......................................................................... 104

Slopes ....................................................................... 104

Cutting Unit Specification .......................................... 105

Cutting Performance ................................................. 106

Recommended Lubricants ......................................... 106

Accessories ............................................................... 106

GUARANTEE

Warranty .................................................................... 108

Service ...................................................................... 108

en-3

INTRODUCTION 2

2.1 IMPORTANT__________________________________________________________

The AR331 with Diesel engine is a self propelled Rotary mower. With hydraulic systems to power the traction

drive, the cutting unit lift and lower, the cutting unit drives and the steering.

IMPORTANT: Do the maintenance indicated in this manual to make sure that the quality of cut is kept at a high

level.

This Manual is part of the machine and must stay with the machine always. The suppliers of new, or used,

machines need to keep this documentation and supply the owners with a copy.

You must use the machine to cut the grass only and not for any other purpose. The Compliance with these

conditions of The operation, service and repair specified by the manufacturer, are understood to be part of the

correct use.

ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and

maintenance procedures.

Make sure that you obey all safety and road traffic regulations.

You must not make any changes to the machine that are not approved by the manufacturer. Unapproved

changes can release the manufacturer from liability for any damage or injury.

Discard worn parts in alignment with all local environment protection regulations. Use the local systems available

in the country where the machine is used, for these materials. When the machine is at its end of life, there are

guidelines in this manual for the removal of the machine from use.

Use only Ransomes Jacobsen Genuine spare parts to meet the machine type approval regulations specified by

the European Union.

2006/42/EC

These instructions are the Original instructions confirmed by Ransomes Jacobsen Limited

en-4

2 INTRODUCTION

2.2 PRODUCT IDENTIFICATION ___________________________________________

A Maximum front axle load in Kg (for all machines being driven

on the highway)

B Weight mass in Kg

C Maximum rear axle load in Kg (for all machines being driven

on the highway)

D Power rating in Kw

E Date code

F Machine type (Name)

G Product code

H Product name

J Serial number

Location of Serial number plate

The serial number plate is found on right hand side of the operators

platform.

Chassis Stamp

The serial number and date code are shown on the right hand chassis

rail between the ROPS mounting bracket and engine hood.

Engine Identification

Serial number plate.

Kg Kw

Kg Kg

West Road

Ransomes Europark

Ipswich IP3 9TT

England

ABCD E

FG

HJ

MADE IN JAPAN

D1105

Serial No.:

Code No.:

XXXXXXX

XXXXX-XXXXX

en-5

INTRODUCTION 2

Location of Serial number plate

The engine serial number is found on the top of the valve cover

toward the front of the mower. Label shows the engine group and

serial number.

The engine serial number is also found on the engine block.

ROPS Serial number plate

A Weight of ROPS

B Date code

C Standard used

D Part number

E For product

F Serial number

ROPS Serial number plate Location

The ROPS serial number plate is found on the right hand ROPS

mount.

CD

E

Kg

A

F

West Road

Ransomes Europark

Ipswich IP3 9TT

England

B

en-6

2 INTRODUCTION

2.3GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS _____________________

2.3.1 DURING SERVICE LIFE _______________________________________________

All the used fluids and parts must be controlled as hazardous materials. Recommended procedures must be followed

for their safe removal.

If a fluid leak occurs, contain the spill to make sure that the leak does not flow into the ground or drainage system.

Follow the regulations in force to make sure that leaks are controlled.

The maintenance procedures in this manual make sure that the damage that the machine can cause in the local

environment is controlled.

When the machine completes its full service life, the following actions must be taken.

2.3.2 END OF SERVICE LIFE _______________________________________________

These guidelines must be used with applicable Health, Safety and Environmental laws. Always use the approved local

waste disposal and agencies for recycled materials.

• Park the machine in an applicable area to use all of the necessary lifting equipment.

• Use correct tools and Personal Protective Equipment (PPE) and take instruction from the technical

manuals applicable to the machine.

• Remove and store correctly.

1. Batteries

2. Fuel

3. Engine coolant

4. Oils

• Read the Technical Manual before you begin to disassemble the machine. Plan the disassembly, give

attention to parts that are in a state of mechanical pressure or contain stored energy e.g springs.

• Items that continue to have a service life must be separated and returned to the local dealer.

•Items that are worn must be separated into the material groups and removed according to the agencies

for the recycled materials that are available. Common examples.

• Steel

•Non ferrous metals

•Aluminium

• Brass

•Copper

•Plastic materials

•Identified

•Can be recycled

• Can not be recycled

•Not identified

•Rubber

•Electrical and Electronic Components

• Some parts are not easily separated e.g Hydraulic hose. These materials must be added to the

“General discarded materials” area.

• Do not burn discarded materials.

Change the machinery records to show that the machine is not in operation and is discarded. Supply this serial number

to The Ransomes Jacobsen Warranty Department to close their records.

en-7

INTRODUCTION 2

2.4 PARTS MANUAL ______________________________________________________

To meet the standard ISO14001, Ransomes Jacobsen Limited does not send a paper parts manual with every

product.

To refer to the parts list for this mower you have four options:

1. Website – www.ransomesjacobsen.com. Select the “ONLINE PARTS LOOK-UP” tab. These pages will

show the parts list and the line drawings you need to help with the identification of spare parts.

2. Website – www.ransomesjacobsen.com. Select the “MANUALS” tab. You have the option to view or

“Download” a PDF version of the parts manual.

3. Complete the form included in the technical manual pack supplied with the machine for one of the two

options below

a. A disc that contains an electronic copy of the Parts Book.

b. A paper copy of the parts manual.

2.5 KEY NUMBERS _______________________________________________________

Record the key numbers

Ignition Key:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Diesel Tank Key:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Record the machine and the engine numbers.

The machine serial number is found on the registration plate and the engine serial number is on the rocker cover.

Machine Number:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Engine Number:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

en-8

2 INTRODUCTION

NOTES

en-9

SAFETY 3

3.1 HOW TO OPERATE SAFELY ______________________________________________

3.1 SAFE OPERATION ______________________________________________________

a Read the Operator’s Manual and other training material. If the operator or technician can not read this

manual, the owner is responsible to describe this material to the operators and technicians. Manuals in

additional languages may be available on the Jacobsen or Ransomes Jacobsen website.

a Read all of the instructions for this mower carefully. Know the controls and the correct operation of the

equipment.

b Children or persons who do not understand these instructions must not use the mower. The local

regulations can limit the age of the operator.

c Never use a mower near persons, including children or animals.

d Remember that the operator or owner is responsible for accidents or hazards that occur to other persons or

their property.

e Never carry passengers.

f Never allow persons to operate or service the mower or its attachments without correct instructions.

g Do not operate equipment while tired, sick or after you use alcohol or drugs.

3.2 PREPARATION ________________________________________________________

a When you operate the mower, wear correct clothing, slip resistant work shoes or boots, work gloves, hard

hat, safety glasses and hearing protection. Long hair, loose clothing or jewelry can be caught in moving

parts.

b Do not operate the equipment with the Interlock system disconnected or if the system does not operate

correctly. Do not disconnect or prevent the operation of any switch.

c Never operate equipment that is not in correct order or with damaged or missing labels, decals, guards,

shields, deflectors or without other protective devices properly installed. When you mow with a side

discharge deck, DO NOT operate the cutting unit without the discharge chute installed.

d Inspect the machine before you operate the mower. Check the tyre pressure, engine oil level, the radiator

coolant level and the air cleaner indicator. Fuel is flammable. Use caution when you add the fuel to the

mower.

e Operate the mower in daylight or in good artificial light. Use caution when you operate the mower during

bad weather. Never operate the mower with lightning in the area.

f Inspect the area, then select the accessories and attachments that are needed to correctly and safely do

the job. Only use parts, accessories and attachments approved by manufacturer.

g Be careful of holes in the terrain and other hazards that are not visible.

h Inspect the area where the equipment is operated. Remove all objects you can find before you operate. Be

careful of obstructions above the ground (low tree limbs, electrical wires) and also underground obstacles

(sprinklers, pipes, tree roots). Enter a new area carefully. Look for possible hazards.

i Inspect the cutting system before you start the mower. Make sure the blades are free to rotate. When you

rotate one blade, other blades can rotate.

WARNING

EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.

Know the location and correct operation of the controls. Potential operators must receive training

from a person trained in the correct operation of the mower.

Only use parts, accessories and attachments approved by Ransomes Jacobsen.

en-10

3 SAFETY

3.3 OPERATION __________________________________________________________

a Never operate the engine without enough ventilation or in an enclosed area. The carbon monoxide in the

exhaust fumes can increase to dangerous levels.

b Never carry passengers. Keep other persons or animals away from the mower.

c Disengage all drives and engage the parking brake before you start the engine. Only start the engine with

the operator in the seat. Never start the engine with persons near the mower.

d Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep

your hands and feet away from the cutting units.

e Do not use on the slopes greater than the safe slope limit for the equipment.

f To guard against overturning or loss of control:

• Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).

• Do not start or stop suddenly on slopes.

• Decrease the speed when you operate on slopes or when you must turn. Use caution when you change

direction. Turf condition can change the mower stability.

• Use caution when you operate the mower near drop-offs, ditches or embankments.

• Be careful of holes in the terrain and other hazards that are not visible.

g When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not

operate the cutting units when you drive in the reverse direction.

h Use caution when you go near corners, trees or other objects that can prevent a clear view.

i Equipment must meet the current regulations to be driven on the public roads.

j Before you move across or operate on the paths or roads, turn off the PTO switch, lift the mowers and

travel at decreased speed. Look for traffic.

k Stop the blades when the mower is on any surface that is not grass.

l Do not release the cut grass in the direction of persons or allow persons near the mower while in operation.

m Do not operate the mower with damaged guards or without safety devices in position.

n Do not change the engine governor setting or over-speed the engine. Never change or tamper with

adjusters that are closed with a seal for the engine speed control.

oBefore you leave the operator compartment, for any reason:

•Disengage all the drives and lower attachments to the ground.

•Engage the parking brake.

•Stop the engine and remove the key.

p When the mower has hit an object or an unusual vibration is noticed, inspect the mower for damage.

Damage must be repaired before returning the mower to service.

q Decrease the throttle setting before you stop the engine.

r Do not use this equipment for uses that the mower was not made for.

en-11

SAFETY 3

3.3.1 ROLLOVER PROTECTIVE STRUCTURE _________________________________

a The ROPS is a safety device. Always use the seat belt when you operate the mower. Make sure the seat

belt can be released quickly in an emergency.

b Inspect the ROPS for damage. Keep the ROPS hardware fastened.

c Do not weld, drill, change or bend the ROPS. Replace a damaged ROPS. Do not try to correct a damaged

ROPS.

d Do not remove the ROPS from the mower.

e Ransomes Jacobsen must approve any changes to the ROPS.

3.3.2 SAFE HANDLING OF FUELS __________________________________________

a The fuel and the fuel vapors are flammable. Use caution when you add the fuel to the mower. The fuel

vapors can cause an explosion.

b Never use the containers that are not approved to keep or transfer fuel.

c Never keep the mower or fuel containers near an open flame or any device that can cause the ignition of

fuel or fuel vapors.

d Never fill the fuel containers inside a vehicle or on a truck or trailer with a plastic liner. Always put the fuel

container on the ground away from your vehicle before you fill the container.

e Refuel the mower before you start the engine. When the engine is in operation or while the engine is hot,

never remove the fuel cap or add fuel to the mower.

f Refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition.

g The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device to

lock the fuel nozzle in the open position.

h Do not over fill the fuel tank. Leave at least 1 inch (25 mm) below the filler neck.

i Always tighten the fuel tank cap and container cap after you add fuel.

j If the fuel spills on your clothing, change your clothing immediately.

en-12

3 SAFETY

3.3.3 MAINTENANCE AND STORAGE ________________________________________

a Before you clean, adjust or repair this equipment, push PTO switch to the OFF position, lower the cutting

unit to the ground, engage the parking brake, stop the engine and remove the key.

b Make sure the mower is parked on a solid and level surface.

c Never work on a mower that is supported only by the jack. Always use the jack stands.

d Never allow persons to service the mower or its attachments without correct instructions.

e When the mower is parked, put into storage or left without an operator, lower the cutting device unless a

positive mechanical lock is used.

f When you put the mower on a trailer or put the mower in storage, close the fuel valve. Do not keep fuel

near flames or drain the fuel inside a building.

g Disconnect the battery before you service the mower. Always disconnect the negative battery cable before

the positive battery cable. Always connect the positive battery cable before the negative battery cable.

h Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To

prevent an explosion, keep any device that can cause sparks or flames away from the battery.

i Disconnect the battery charger from the power supply before you connect or disconnect the battery charger

to the battery. Wear protective clothing and use insulated tools when you service the battery.

j Be careful and wear gloves when you check or service the cutting unit blades. Replace any damaged

blades, do not try to correct a damaged blade.

k Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in

operation, unless the adjustment needs the engine in operation.

lCarefully release the pressure from components with stored energy.

m To prevent injury from the hot, high pressure oil, never use your hands to check for oil leaks. Use the paper

or cardboard to find leaks.

n The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your

skin, a doctor must remove the hydraulic fluid surgically within a few hours or gangrene can occur.

o When you service the hydraulic system, make sure the hydraulic fittings, tubes and hoses are tightened to

the correct torque. Make sure the hydraulic system is in good condition before you start the engine.

p Keep the mower and the engine clean.

q Allow the engine to become cool before storage and always remove the ignition key.

r Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.

s Replace worn or damaged parts for safety. Replace damaged or worn labels. Only use parts, accessories

and attachments approved by Ransomes Jacobsen.

t To decrease the fire hazard, remove materials that burn from the engine, muffler, battery tray and fuel tank

area.

uDisconnect the battery and controller connectors before you weld on this mower.

3.3.4 WHEN YOU PUT THE MOWER ON A TRAILER ____________________________

a Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and can

carry the weight of the mower.

b Use a full-width ramp to load or unload the mower on a trailer Be careful when loading or unloading the

mower..

c Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be

sent down and toward sides of trailer.

Make sure that all latches are correctly fastened.

en-13

SAFETY 3

3.3.5 IMPORTANT SAFETY NOTES _________________________________________

This safety alert symbol is used to alert you to possible hazards.

DANGER:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

CAUTION:

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE:

Only drive the machine at road speed when you are on a highway. You must not select road speed on grass

areas or rough roads and gravel tracks.

Some illustrations in this manual can show shields, guards or plates removed for clearness. This equipment must

not be operated without these devices correctly fastened in position.

By following all instructions in this manual, you increase the life of your machine and keep its maximum

performance. Adjustments and maintenance must always be done by an approved technician.

If additional information or service is required, contact your authorized Ransomes Jacobsen Dealer. Your

dealer has personnel trained in the latest service procedures for your equipment.

WARNING

The Interlock System on this mower prevents the starting of the mower unless

a.) The parking brake is Engaged.

b.) The mow switch is in the OFF position,

c.) The traction pedal is in the Neutral position.

d) The operator is in the seat.

The system stops the engine when the operator leaves the seat (a) without the parking brake engaged

or (b) the mow switch is not in the OFF position. NEVER operate the mower unless the Interlock

System is working.

WARNING

1. Before leaving the operator’s position for any reason:

a. Return traction pedal to the Neutral position.

b. Disengage all drives.

c. Lower all implements to the ground.

d. Engage parking brake.

e. Stop the engine and remove the ignition key.

2. Keep your hands, feet, and clothing away from moving parts. Wait for all movement to stop

before you clean, adjust, or service the machine.

3. Keep the area of operation clear of all persons and animals.

4. Never carry any passengers.

5. Never operate the equipment without a correctly fastened grass deflector in position.

en-14

3 SAFETY

WARNING

California proposition 65

Engine exhaust, some of its constituents, and some vehicle components contain or release chemicals

known to the state of California to cause cancer and birth defects or other reproductive harm.

WARNING

To prevent injury from the hot oil at high pressure, do not use your hands to check for oil leaks, make

sure that you use paper or cardboard.

Release of hydraulic fluid at high pressure has enough force to enter through the skin. If the fluid enters

through the skin, the fluid must be surgically removed within hours by a specialist doctor or gangrene

may result.

WARNING

When the machine is driven off-road, a seat belt must be worn only when a ROPS frame is in position.

This warning is because a seat belt must be worn with a ROPS to follow the machinery directive,

2006/42/EC sections 3.2.2, seating & 3.4.3, rollover. (ANSI b71.4-2012 section 20.7)

Ransomes Jacobsen Limited recommends that the owner/user of the machine completes a local risk

assessment of the machine to find any conditions that do not follow this rule. e.g. When you drive the

machine next to water or on the highway.

WARNING

Explosive gases are released by batteries. The battery contains corrosive acid and supply an electrical

current that is high enough to cause burn injuries to the body.

WARNING

You must not use this machine to tow other vehicles.

WARNING

Ear protection must be worn when you operate machines with

an operator ear noise level of more than 85 db(a) leq.

en-15

SAFETY 3

WARNING

Vibration Exposure Limits

Exposure limits are calculated as a combination of the vibration level (magnitude) of the tool and the

Daily Exposure Time (Trigger Time). E.g. A product with 5m/s² vibration can be used up to 2 hours/day to

reach the EAV and up to 8 hours/day to reach the ELV.

Exposure Action Value (EAV) - Daily vibration exposure A(8) = 2.5m/s²

Where daily vibration exposure A(8) is below 2.5m/s² the risk is relatively low and no action need be

taken

Exposure Limit Value (ELV) - Daily Vibration Exposure A(8) = 5.0m/s²

If several tools are used the exposure values must be combined:

Total exposure is then the combined value of the activities

WARNING

Never mow if there is a risk of lightning or you hear thunder. If you are in the middle of mowing, stop in

a safe place, turn off the engine and go inside a building.

CAUTION

When you do any welding on the machine, the battery, controller and display must be disconnected

before you start. You must not open the controller. If the controller is opened, this can cancel all of the

warranties and can cause the failure of the machine.

CAUTION

Personal protective equipment (PPE), for example safety glasses, protective footwear, a hard hat,

leather work gloves and ear protection must be used after the owner/user completes a local risk

assessment of the mower, to prevent injury.

Training in all manual operations must be given by an approved person before the machine is used the

first time.

en-16

4 LABELS

4.1 SAFETY LABELS EC ____________________________________________________

4153197

L

4181865

16°+

009114170

A B C D

E F G H

J K

en-17

LABELS 4

A. 009034920 Caution, Stay Away From Hot Surfaces.

B. 009034880 Caution, Fan Blade, Do Not Open Or Remove The Safety Shields While The Engine Is

In Operation.

C. 009034900 Caution, Drive Belt, Do Not Remove The Safety Shields While The Engine Is In

Operation.

D. 009114340 Caution, Diesel Fuel.

E. 009114100 Caution, Battery.

F. 009114170 Slope Angle.

G. 009034960 Caution, Rotating Blades.

H. 009114380 Caution, Fasten Seat Belt.

J 4153197 Caution, Stop The Engine And Remove The Starter Key Before You Pressure Wash

The machine.

K. 4164860 Caution, Hydraulic Oil.

L. 4181865 Decal, Warning.

en-18

4 LABELS

4.2 INSTRUCTION LABELS EC _______________________________________________

0.7 bar

10 psi

673581

L

4324674

B

I

O

D

E

G

R

A

D

A

B

L

E

F

L

U

I

D

43974864397486

4374506

H J K

D E F G

A B C

TOTAL EQUIVIS ZS 46

4286422

en-19

LABELS 4

Description

A. 009034770 Guaranteed Sound Power Level. K. 4374506 Keyswitch and Light.

B. 4178900 Diesel Fuel. L. 3008682 Tow Valve.

C. 4397486 Traction. M. 4392886 Control Panel.

D. 673581 Tyre Pressure. M. 4392886 Control Panel.

E. 4164861 Forward / Reverse Traction Pedal. N. 838363. Throttle Lever.

F 4286422 Hydraulic Fluid. P. 674418 27” Front HOC Decal.

G. 4397046 Jacking Point. Q. 674420 27” Rear HOC Decal R\H

H. 4164580 Lubrication Point. R. 674432 27” Rear HOC Decal L\H

4392886

M P

N

1

2

3

4

6

9

7

10

12

5

8

11

674420

KH

1

2

3

4

5

6

7

8

9

10

11

12

11

10 7

8

96

5

4

3

2

1

19 mm

25 mm

31 mm

38 mm

44 mm

50 mm

57 mm

63 mm

69 mm

76 mm

82 mm

88 mm

0.75 in

1.00 in

1.25 in

1.50 in

1.75 in

2.00 in

2.25 in

2.50 in

2.75 in

3.00 in

3.25 in

3.50 in

K H

19 mm 0.75 in 1

25 mm 1.00 in 2

31 mm 1.25 in 3

38 mm 1.50 in 4

44 mm 1.75 in 5

50 mm 2.00 in 6

57 mm 2.25 in 7

63 mm 2.50 in 8

69 mm 2.75 in 9

76 mm 3.00 in 10

82 mm 3.25 in 11

88 mm 3.50 in 12

674432

12

11

10

7

8

9

6

5

4

3

2

1

Q R

en-20

5 CONTROLS

5.1 OPERATOR WORKSTATION __________________________________________

5.2 - Control Panel

5.3 - Throttle Control

5.4 - Armrest Adjuster

5.5 - Traction Pedal

5.6 - Mow Speed Lever

5.7 - Steering Tilt Lever

5.9 - Tow Valve

5.10 - Brake Valve (Under Floorboard)

5.6

5.5

5.4

5.2

5.3

5.7

5.10

5.9

La page charge ...

Jacobsen 068021-E410 Maintenance Manual

Jacobsen 068021-E410 Maintenance Manual

dans d''autres langues

Documents connexes

Autres documents