DeWalt DCN890P2 Manuel utilisateur

Marque: DeWalt

Modèle: DCN890P2

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCN890

20V MAX* Concrete Nailer

Cloueuse pour béton 20V MAX*

Clavadora para concreto de 20 V MAX*

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 19

Español (traducido de las instrucciones originales) 38

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings

and all instructions. Failure to follow the

warnings and instructions may result in

electric shock, fire and/or seriousinjury.

WARNING: To reduce the risk of injury, read

the instructionmanual.

If you have any questions or comments about

this or any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

Trigger

Trigger lock-off

Power Selection Switch

Utility hook

Contact trip release lever

Contact trip

Removable top stand

Stall release lever

Low battery & jam/stall

indicator lights (x2)

Battery pack

Battery release button

Magazine

Magazine support leg

Magazine release lever

Pusher

Fig. A

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

ENGLISH

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from

the battery may cause irritation orburns.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

Nailer Safety Warnings

• Always assume that the tool contains fasteners.

Careless handling of the nailer can result in unexpected

firing of fasteners and personalinjury.

• Do not point the tool towards yourself or anyone

nearby. Unexpected triggering could discharge a fastener

causing aninjury.

• Do not actuate the tool unless the tool is placed

firmly against the workpiece. If the tool is not in

contact with the workpiece, the fastener may be deflected

away from yourtarget.

• Disconnect the tool from the power source when the

fastener jams in the tool. While removing a jammed

fastener, the nailer may be accidentally activated if it is

pluggedin.

• Do not use this nailer for fastening electrical cables.

It is not designed for electric cable installation and may

damage the insulation of electric cables thereby causing

electric shock or firehazards.

• Never operate tool with Magazine disengaged or

separated from tool.

Additional Nailer Safety Warnings



WARNING: When using any nailer, all safety

precautions, as outlined below, should be followed

to avoid the risk of death or serious injury. Read and

understand all instructions before operating thetool.

• Hold tool by insulated gripping surfaces when

performing an operation where the pin may

contact hidden wiring. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock

theoperator.

• Always wear appropriate personal hearing and

other protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearingloss.

• Disconnect battery pack from the tool when not in

use. Always remove battery pack and remove fasteners

from magazine before leaving the area or passing the

tool to another operator. Do not carry tool to another

work area in which changing location involves the use

of scaffoldings, stairs, ladders, and the like, with battery

pack connected. Do not make adjustments, perform

maintenance or clear jammed fasteners while battery is

inplace.

• Always use trigger lock-off when tool is not in

immediate use. Using the trigger lock-off will prevent

accidental discharge.

• Do not remove, tamper with, or otherwise cause

the tool, trigger or trigger lock-off, to become

inoperable. Do not tape or tie trigger in the on position.

Do not remove spring from contact trip. Make daily

inspections for free movement of trigger. Uncontrolled

discharge couldresult.

• Inspect tool before use. Do not operate a tool if any

portion of the tool, trigger, or trigger lock-off is

inoperable, disconnected, altered, or not working

properly. Damaged parts or missing parts should be

repaired or replaced before use. Refer toRepairs.

• Do not alter or modify the tool in anyway.

• Always assume that the tool containsfasteners.

• Do not point the tool at co-workers or yourself at

any time. No horseplay! Work safe! Respect the tool as a

workingimplement.

• Keep bystanders, children, and visitors away while

operating a power tool. Distractions can cause you to

lose control. When tool is not in use, it should be locked in

a safe place, out of the reach ofchildren.

• Do not overreach. Maintain proper footing and

balance at all times. Loss of balance may cause

personal injury.

• Use the tool only for its intended use. Do not

discharge fasteners into open air or any material

too hard for the pin to penetrate. Do not use the

body of the tool or top cap as a hammer. Discharged

pin may follow unexpected path and causeinjury.

• Always keep fingers clear of contact trip to prevent

injury from inadvertent release of thepin.

ENGLISH

• Refer to the Maintenance and Repairs sections for

detailed information on the proper maintenance of

thetool.

• Always operate the tool in a clean, lighted area.

Be sure the work surface is clear of any debris and be

careful not to lose footing when working in elevated

environments such asrooftops.

• Fasteners must be driven straight into the material.

Do not tilt the nailer while driving fasteners. Personal

injury can result from ricocheted or jammedpins.

• Keep hands and body parts clear of immediate

workarea.



WARNING: To avoid injury keep hands and body

away from the front discharge area of thetool.

• Do not use tool in the presence of flammable dust,

gases or fumes. This tool produces sparks that can ignite

gases or dust causing an explosion. Driving a pin into

another pin may also cause aspark.

• Keep face and body parts away from back of the tool

cap when working in restricted areas. Sudden recoil

can result in impact to the body, especially when nailing

into hard or densematerial.

• Grip tool firmly to maintain control while allowing

tool to recoil away from work surface as fastener

isdriven.

• Be aware of material thickness when using nailer. A

protruding pin may causeinjury.

• Do not drive pins blindly into walls, floors or other

work areas. Fasteners driven into live electrical wires,

plumbing, or other types of obstructions can result

ininjury.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use tool while tired or under the influence of drugs,

alcohol, or medication. A moment of inattention

while operating power tools may result in serious

personalinjury.

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

ENGLISH

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or serious injury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a short circuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and

Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to the

FLEXVOLT™ battery, the

battery is in Shipping Mode.

Strings of cells are electrically

disconnected within the pack resulting in three batteries

with a lower Watt hour (Wh) rating as compared to one

battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hour batteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 battery implied).

ENGLISH

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or serious injury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

ENGLISH

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center for recycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting battery pack.

Fig. C

2. Insert the battery pack

10

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process has started.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

11

on the battery pack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before first

use.

Charger Operation

Refer to the indicators below for the charge status of the

battery pack.

DCB101

Charging

Fully Charged

Hot/Cold Pack Delay

Problem Pack or Charger

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132:

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

yellow light will turn off and the charger will resume the

charging procedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing to light or by displaying a problem pack or charger

blink pattern.

NOTE: This could also mean a problem with a charger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized service center.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery pack life.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

ENGLISH

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to be cooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of the charger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fully charged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in the slots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaning solutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack in an air temperature below +40°F

(+4.5°C), or above +104°F (+40°C). This is important

and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local service center.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the battery pack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting to clean.

6. Do not freeze or immerse the charger in water or any

other liquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimal results.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged before use.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

Intended Use

Your concrete nailer is intended ONLY for use in driving

pins into structural steel/wood/concrete.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

Use ONLY pins that are recommended by

DeWALT

and

meet applicable building code requirements.

This tool is intended for use by construction professionals.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

ENGLISH

TOOL SPECIFICATIONS

Actuation Mode Sequential

Voltage 20

Height 16.0" (406 mm)

Width 4.1" (104 mm)

Length 15.4" (390 mm)

Weight 9.3 lbs (4.218 kg)

Magazine Angle 15˚

Loading Capacity Up to 33 pins

PIN SPECIFICATIONS

Pin Lengths 1/2" - 2 1/4" (13 mm - 57 mm)

Shank Diameters .102" - .145" (2.6 mm - 3.7 mm)

Pin Stick Angles 15˚

Dry Fire Lock Out

The concrete nailer is equipped with a dry fire lockout which

prevents the tool from actuating when the magazine is

nearly empty. When 3 pins remain in the magazine, the tool

ceases to operate. Refer to LoadingtheTool to reload a

stick of collated pins.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Utility Hook (Fig. A, D)

The

DeWALT

cordless nailers include an integrated utility

hook

4

and can be attached to either side of the tool to

accommodate left- or right-handed users.

If the hook is not desired at all, it can be removed from

thetool.

To Remove Utility Hook

1. Remove battery pack from tool.

2. To switch the tool from right- to left-hand usage simply

remove the screw

17

from the opposite side of the tool

and re attache the utility hook

4

on the other side.

3. Replace battery pack.

Fig. D



WARNING: Remove pins from magazine before

making any adjustments or servicing this tool. Failure

to do so may result in serious injury.



WARNING: Disconnect battery pack from tool before

making any adjustments, changing accessories,

servicing, or moving the tool. Such preventative

safety measures reduce the risk of starting the

toolaccidentally.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping or

falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be

easily knocked over.

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.



WARNING: Read the section titled Nailer Safety

Warnings at the beginning of this manual. Always

wear eye and ear protection when operating this

tool. Keep the nailer pointed away from yourself and

others. For safe operation, complete the following

procedures and checks before each use of thenailer.

1. Wear proper eye, hearing and respiratoryprotection.

2. Remove battery pack fromtool.

3. Lock the pusher in the back position and remove all pins

from themagazine.

4. Check for smooth and proper operation of contact

trip and pusher assemblies. Do not use tool if either

assembly is not functioning properly. NEVER use a tool

that has the contact trip restrained in the upposition.

5. NEVER use a tool that has damagedparts.



WARNING: To reduce the risk of personal injury,

disconnect battery pack from tool before performing

maintenance, clearing a jammed pin, leaving work

area, moving tool to another location or handing the

tool to anotherperson.

Installing and Removing the Battery Pack

(Fig. A)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

10

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

11

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

ENGLISH

Proper Hand Position (Fig. E)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main handle

as shown in Fig. E.

Fig. E

Preparing the Tool

NOTICE: NEVER spray or in

any other way apply lubricants

or cleaning solvents inside the

tool. This can seriously affect

the life and performance of

thetool.

NOTE: The battery pack is not fully charged out of the

carton. Follow instructions outlined (refer to Charging

ABattery).

1. Read the Nailer Safety Warnings section of

thismanual.

2. Wear eye and earprotection.

3. Remove battery fromtool.

4. Ensure magazine is empty of allfastners.

5. Check for smooth and proper operation of contact

trip and pusher assemblies. Do not use tool if either

assembly is not functioning properly. NEVER use

a tool that has the contact trip restrained in the

actuatedposition.

6. Keep tool pointed away from yourself andothers.

7. Insert fully charged batterypack.

Using the Trigger Lock-off (Fig. F)



WARNING: To reduce the risk of serious personal

injury, do not keep trigger depressed when tool is not

in use. Keep the trigger lock-off switch LOCKED (Fig.F)

when the tool is not inuse.



WARNING: To reduce the risk of serious personal

injury, lock off trigger, disconnect battery pack

from tool and remove pins from magazine before

makingadjustments.

Each

DeWALT

nailer is equipped with a trigger lock-off

2

which when pushed to the right as shown in FigureF,

prevents the tool from firing a pin by locking the trigger and

bypassing power to themotor.

Fig. F

When the trigger lock-off is pressed to the left, the tool will

be fully operational. The trigger lock-off should always be

locked off (Fig.G) whenever any adjustments are made or

when tool is not in immediateuse.

NOTICE: Do not store tool with battery pack installed. To

prevent damage to the pack and to ensure best battery

life, store battery packs out of the tool or charger in a cool,

drylocation.

Loading the Tool (Fig. G)



WARNING: Keep the tool pointed away from yourself

andothers.



WARNING: Never load pins with the contact trip or

triggeractivated.



WARNING: Always remove battery pack before

loading or unloadingpins.



CAUTION: Keep fingers clear of pusher latch track to

preventinjury.



WARNING: The trigger lock-off should always be

engaged whenever any adjustments are made or

when tool is not inuse.



WARNING: Fasteners used to install metal connectors

must meet the requirements of the applicable building

codes and must be installed in compliance with code

requirements and metal connector hardware supplier

specifications. Failure to properly install connectors

may result in structuralfailures.

1. Turn the nailer upsidedown.

2. Slide the spring-loaded pusher latch

15

to the base of

the magazine to lock it intoplace.

Fig. G

3. Drop pin strips into the loading slot of the magazine,

making sure the pin heads align correctly with the slot

opening. (Refer to Pin Specifications to determine

compatible size.)

4. Keeping fingers clear of the track, close the magazine by

releasing the pusher latch. Carefully allow the latch to

slide forward and engage the pinstrip.

ENGLISH

Fig. I

Actuating the Tool (Fig. A)



WARNING: Always wear proper eye [ANSI Z87.1

(CAN/CSA Z94.3)] and ANSI S12.6 (S3.19) hearing

protection when operatingtool.

The motor rotation speed is automatically restored after

driving a pin to allow fast consecutive nailing.

1. Release the trigger lock-off

2

2. Push the contact trip

6

against the worksurface.

3. Pull the trigger switch

1

to actuate thetool.

4. Release the trigger and raise the nailer from the

work surface. NOTE: The tool motor returns to full

speed automatically without the contact trip

6

beingdepressed.

5. Repeat steps 3–5 to actuate the nextnail.

Pin/Fastener Troubleshooting

Properly driven pin Over driven pin

CONCRETE

Pin does not hold in the concrete.

Cause:

- Too hard/high strength

concrete.

- Hard or large aggregate

inconcrete.

Action:

- Use shorter pin.

- Switch to higher power

setting.

Unloading the Tool



WARNING: The trigger lock-off should always be

locked off whenever any adjustments are made or

when tool is not inuse.

1. Slide the spring-loaded pusher latch to the base of the

magazine to lock it intoplace.

2. Tip the tool up until the fastener strip slides freely out of

themagazine.

3. With battery removed, check the nosepiece to verify

there are no pinsremaining.

NOTE: The tool is equipped with a magnet in the nose

area for improved tool performance. When unloading,

always verify that the small sticks of pins are not held to the

magnetized nosepiece.

Power Setting Summary (Fig. H, I)

This nailer is equipped with a power selection switch

3

adjust the tool when driving into differentmaterials.

Power setting 1: Softer materials (low strength concrete/

cinder block)

Power setting 2: Medium hardness materials (High strength

concrete)

Power setting 3: Hard materials (Structural Steel)

In the event pins are not driving to depth in power setting1,

you may have to switch to power 2 or 3 for additional

drivingpower.

Fig. H

NOTICE: Driving pins into soft materials at high

power settings will cause excessive wear to your

tool and may result in early failures.

Power

Setting

Application Typical Pin Length

Fastening Steel/Wood to Low Strength

Concrete/Masonry (<4000 psi)

3/4" to 1" typ.

Fastening Steel/Wood to High Strength

Concrete (>4000 psi)

3/4" to 1-1/2" typ.

Fastening Steel/Wood to High Strength

Concrete (>4000 psi)

Fastening to structural steel;

2x4 to Concrete

1/2" or 2-1/4"typ.



WARNING: Pins must be driven straight into the

material. Do not tilt nailer while driving fasteners.

Refer to Fig.I. Pin retention values improve when the

tool is fired perpendicular to the material.

ENGLISH

Pin does not drive deep enough.

Cause:

- Pin too long.

- Power setting too low.

Action:

- Use shorter pin.

- Switch to higher power

setting.

Pin drives too deep.

Cause:

- Pin too short for application.

- Power setting too high.

Action:

- Use longer pin.

- Switch to lower power

setting.

Pin bends.

Cause:

- Pin hit large aggregate on

entry.

- Too hard/high strength

concrete.

- Pin hit rebar just under

surface.

Action:

- Use shorter pin.

- Make sure nailer is

perpendicular to the work

surface.

- Move 3 inches and

tryagain.

STEEL

Pin does not penetrate the surface.

Cause:

- Power setting too low.

- Material to hard for pin

type.

Action:

- Increase tool power setting.

Pin breaks or bends.

Cause:

- Pin too long.

- Power setting too low.

- Material to hard for pin

type.

Action:

- Use shorter pin.

- Switch to higher power

setting.

Pin does not hold in the steel.

Cause:

- Steel base material too thin.

Action:

- Use thicker base material.

Headlights/LED Indicator (Fig. A)

There are low battery and jam/stall indicator lights

9

located on the front of the tool on each side of the

magazine.

LOW BATTERY

Replace battery with a charged pack.

HOT PACK

Let the battery cool or replace it with

a cool pack.

JAM/STALL CONDITION

Rotate the stall release lever to

release.

Refer to Stall Release or Clearing a

Jammed Pin.

HOT TOOL (Both LEDs Flashing)

Let the tool cool down before

continuing use.

or any other

combination.

ERROR

Reset tool by removing and

reinserting battery pack or cycling

trigger lock off. If error code persist,

take tool to an authorized

DeWALT

service center.

Stall Release (Fig. J)

If the nailer is used in harder material where all available

energy in the motor is used to drive a fastener, the tool may

stall. The driver will not complete the drive cycle and the

jam/stall indicator will flash. Rotate the stall release lever

8

on the tool and the mechanism will release.

NOTE: The tool will disable itself and not reset until the

battery pack has been removed and reinserted. If the

driver does not automatically return to the home position,

proceed to Clearing a Jammed Pin. If the unit continues

to stall please review the material and fastener length to

be sure that it is not too rigorous an application. The nailer

could also be overheated and needs time to cool before

further use.

ENGLISH

Fig. J

Clearing a Jammed Pin (Fig. A, K)



WARNING: To reduce the risk of serious personal

injury, disconnect battery pack from tool before

making any adjustments, changing accessories,

servicing, or moving the tool. Such preventative

safety measures reduce the risk of starting the

toolaccidentally.



CAUTION: When removing a jammed pin, DO

NOT orient the nailer with the nose up or with

the battery foot up. Positioning the nailer this way

makes the jammed pin or pieces of the pin more likely

to be ingested into the nailer. If any portion of a pin is

ingested into the tool, the pin should be retrieved by

removing the topcap.

If a pin becomes jammed in the nosepiece, keep the tool

pointed away from you and follow these instructions

toclear:

1. Remove battery pack from tool and engage trigger

lock-off.

2. After laying the tool on its side, slide the spring-loaded

pusher latch

15

to the base of the magazine to lock it

into place and unload pinstrip.

3. Rotate the magazine release lever

14

and rotate the

magazine

12

forward.

Fig. K

4. Remove jammed/bent nail, using pliers if necessary. The

contact trip can be removed if necessary. Refer to To

Replace ContactTrip.



CAUTION: If any portion of a pin is ingested into

the tool, the pin should be retrieved by removing the

topcap.

5. If the driver is in the down position, rotate the stall

release lever on the top of thenailer.

NOTE: If the driver will not reset after rotating the stall

release lever, manually resetting the blade with a long

screw driver may benecessary.

6. Rotate the magazine back into position under the nose

of the tool and close the magazine releaselever.

7. Reinsert batterypack.

NOTE: The tool will disable itself and not reset until the

battery pack has been removed andreinserted.

8. Reinsert pins into magazine (refer to Loading theTool).

9. Release the pusherlatch.

10. Disengage the trigger lock-off when ready to

continuenailing.

NOTE: Should pins jam frequently or the driver continually

fail to reset, have tool serviced by an authorized

DeWALT

servicecenter.

Cold Weather Operation

When operating tools at temperatures below freezing:

1. Keep tool as warm as possible prior touse.

2. Actuate the tool 10 or 15 times into scrap lumber

beforeusing.

Hot Weather Operation

Tool should operate normally. However, keep tool out of

direct sunlight as excessive heat can deteriorate bumpers

and other rubber parts resulting in increasedmaintenance.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

DAILY MAINTENANCE CHART

ACTION Clean magazine, pusher, and contact trip

mechanism.

WHY Permits smooth operation of magazine,

reduces wear, and prevents jams.

HOW Blowing off the tool with compressed air is

the most effective way to clean the tool. The

use of oils, lubricants periodically or solvents

is not recommended as they tend to attract

debris and/or damage the plastic parts of

the tool.

ACTION Before each use, check to ensure all screws

and fasteners are tight and undamaged.

WHY Prevents jams and premature failure of

toolparts.

HOW Tighten loose screws using the appropriate

hex wrench or screwdriver.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

ENGLISH

Fig. L

DCN8901 Driver Blade Replacement Kit

(Fig. M, N, O)



WARNING: For your own safety, read the tool

instruction manual before using any accessory.

Failure to heed these warnings may result in serious

personal injury and damage to the tool and the

accessory. When servicing this tool, use only identical

replacementparts.

NOTICE: All the mechanical parts of the driver

replacment kit are shown for convenience and

verification ofinclusion.

To change a worn driver:

1. Using a T-20 Torx, loosen the four screws

18

on either

side of the unit. Refer to FigureM.

2. Remove the four screws and the removable top

stand

7

. Refer to FigureM.

3. Remove housing end cap

19

. Refer to FigureM.

Fig. M

4. Push up on the rear of the driver

20

until you hear a

click, then push the driver forward while holding it in

this position until it passes the upper bumper assembly.

Refer to FigureO.

5. Remove guide rods

21

. Refer to FigureO.

6. Remove upper bumper assembly

22

. Refer to FigureN.

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Lubrication

NOTICE: NEVER spray or

in any other way apply

lubricants or cleaning

solvents inside the tool.

This can seriously affect

the life and performance of

thetool.

DeWALT

tools are properly lubricated at the factory and are

ready for use. However, it is recommended that, once a year,

you take or send the tool to a certified service center for a

thorough cleaning andinspection.

Accessories



WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.

DCN8901 Driver Blade Replacement Kit

DCN8902 Magnetic Stick-E Contact Trip

DCN8903 Stick-E Contact Trip

DCN8904 Standard Contact Trip

DCN8905 Pole Tool

DCN8902: Magnetic Stick-E Contact Trip

(Fig. L)

For some applications, using a Stick-E contact trip may

bedesirable.



WARNING: For your own safety, read the tool

instruction manual before using any accessory.

Failure to heed these warnings may result in personal

injury and serious damage to the tool and the

accessory. When servicing this tool, use only identical

replacementparts.

To Replace Contact Trip

1. Push down on the contact trip releaselever.

2. Pull the contact trip out of the nose of the tool.

3. Hold down the trip release lever

4. With the contact trip alignment marker facing up, as

shown in Figure L, insert the contact trip fully into

thetoolnose.

5. Release thelever.

ENGLISH

Fig. N

7. Lift the rear of driver until at an angle and pull the driver

out. Refer to FigureO.

8. Replace driver and follow steps in reverse to reassemble

9. Ensure new driver slides smoothly through the gun

before fullreassembly.

Fig. O

10. Return the driver, guide rods, bumpers, housing end

cap, and removable top stand back onto the unit. It

is important to try the alignment of the driver and

the flywheel before screwing the housing end cap

back on to the unit. This can be done by connecting

a battery and pushing then releasing the nose of the

unit against a bench or hard surface. This will start the

motorspinning.

NOTE: When the driver and the flywheel are correctly

aligned, you will hear the motor coast back down

from full speed. If the driver and the flywheel are not

correctly aligned, the motor may not start up, may

slow down much faster than normal along with a loud

grinding noise from the unit. If this happens remove

and reseat the driver, making sure the bumpers are

seatedcorrectly.



WARNING: Always test the unit by firing 3/4" pins

in power setting 1 into scrap material, to ensure that

the tool is working properly. If tool does not operate

properly, contact a recognized

DeWALT

service

centerimmediately.

Recommended accessories for use with your tool are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact

DeWALT

Industrial Tool Co., 701

East Joppa Road, Towson, MD 21286, call 1–800–4-

DeWALT

(1–800–433–9258) or visit our website www.

DeWALT

.com.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement) should

be performed by a

DeWALT

factory service center

or a

DeWALT

authorized service center. Always use

identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from

the date of purchase. This warranty does not cover part

failure due to normal wear or tool abuse. For further detail

of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-

DeWALT

(1-800-

433-9258). This warranty does not apply to accessories

or damage caused where repairs have been made

or attempted by others. THIS LIMITED WARRANTY IS

GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase. ADD WEAR STATEMENT: NO SPRINGS

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

ENGLISH

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB606

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

ENGLISH

TROUBLESHOOTING GUIDE

Many common problems can be solved easily by utilizing the chart below. For more serious or persistent problems,

contact a

DeWALT

service center or call 1-(800)-4-

DeWALT



WARNING: To reduce the risk of serious personal injury, ALWAYS disconnect battery pack from tool before

all repairs

SYMPTOM CAUSE FIX

Motor does not run with contact

trip depressed

Trigger lock in locked position Unlock trigger lock.

Dryfire lock out engaged, blocking contact trip from

traveling fully

Load more pins into magazine.

Tool is stalled, locking the motor from rotating Rotate the stall release lever on the tool and the mechanism

will release. If driver does not return, remove battery and

manually push driver back to home position.

Battery is hot. (Check LED indicator to verify these

conditions.)

Let the battery cool or replace it with a cool pack.

Tool is hot. (Check LED indicator to verify these

conditions.)

Let the tool cool down before continuing use.

Bent contact trip See authorized service center.

Motor stops running after 5 seconds Normal operation, release contact trip and redepress.

Terminals are dirty or damaged See authorized service center.

Damaged internal electronics See authorized service center.

Damaged Trigger See authorized service center.

Battery is hot Let the battery cool or replace it with a cool pack.

Tool is hot Let the tool cool down before continuing use.

Tool does not actuate (motor runs

but will not fire)

Dryfire lock out engaged, blocking contact trip from

traveling fully

Load pins into magazine.

Low battery charge or damaged battery Check charge level if pack shows state-of-charge. Charge or

replace battery pack if necessary.

Jammed nail/drive blade not returned to home

position

Remove battery, clear jammed nail, cycle stall release lever,

(push driver up manually if necessary) reinsert battery pack.

Damaged driver Replace driver with kit.

Jammed internal mechanism See authorized service center.

Damaged internal electronics See authorized service center.

Motor starts up but generates a

lot of noise

Jammed pin and driver is stuck in down position Use stall release lever, clear and jammed pins, and return

driver manually if necessary.

Damaged driver Replace driver with kit.

Driver blade continues to get stuck

in down position

Jammed pin and driver is stuck in down position Use stall release lever, clear any jammed pins, and return

driver manually if necessary.

Debris in nosepiece Clean nose area and watch closely for small pieces of broken

pins stuck in the track. Refer to Clearing a Jammed Pin.

Damaged or worn driver Replace driver with kit.

ENGLISH

SYMPTOM CAUSE FIX

Tool operates but does not drive

fasteners fully

Power setting in wrong position. Set power to appropriate setting.

Tool not firmly applied to workpiece Apply adequate force to tool securing it tightly to workpiece

See instruction manual.

Material and fastener length If the unit continues to stall (forcing the need to rotate the

stall release lever) choose the appropriate material and

fastener length that is not too rigorous of an application.

Use of incorrect power setting If trying to drive longer pins in soft woods, or driving pins

into harder materials using power setting 1 - adjust power

setting to 2.

Damaged or worn driver tip Replace driver with kit.

Damaged actuation mechanism See authorized service center.

Tool operates, but no fastener

is driven

No pins in magazine Load pins in magazine.

Wrong size or angle pins Use only the recommended pins. Refer to Pin Specifications.

Debris in nosepiece Clean nose area and watch closely for small pieces of broken

pins stuck in the track.

Debris in magazine Clean magazine

Damaged pusher spring Replace spring; see authorized service center.

Worn magazine Replace magazine. See authorized service center.

Damaged or worn driver Replace driver with kit.

Jammed nail Wrong size or angle pins Use only the recommended pins. Refer to Pin

Specifications.

Magazine not secured after previous jam clear/

inspection

Make sure to magazine is latched properly.

Material and fastener length If the unit continues to stall (forcing the need to rotate the

Stall release lever) choose the appropriate material and

fastener length that is not too rigorous an application.

Debris in nosepiece Clean nose area and watch closely for small pieces of broken

pins stuck in the track.

Worn magazine Replace magazine. See authorized service center.

Damaged pusher spring Replace springs. See authorized service center.

Dry fire lock out is engaged with only 2–4 pins

remaining in magazine and the user is applying

excessive force to contact trip, overriding the lockout

Load more pins in magazine to disengage dryfire lockout.

Tool is not yet run-in New tools can take 100–500 pins for parts to mesh and

wear in together. Drive shorter pins during this period if

experiencing difficulty fully driving pins.

Use of incorrect power setting If trying to drive longer pins in soft materials, or driving pins

into harder materials using power setting 1 - adjust power

setting to 2 or 3.

Damaged or worn driver Replace driver with kit.

Driver blade does not slide

backward and forward smoothly

through its firing path

Driver blade is bent Replace driver with kit.

La page charge ...

DeWalt DCN890P2 Manuel utilisateur

Marque: DeWalt

Modèle: DCN890P2

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCN890P2 User manual
español: DeWalt DCN890P2 Manual de usuario

DeWalt DCN890P2 Manuel utilisateur

Ce manuel convient également à

DeWalt DCN890P2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents