KitchenAid KFP0718L/KFP0718 Food Processors Manuel utilisateur

KFP0718L

KFP0718

PARTS AND FEATURES

PARTS AND ACCESSORIES

Heavy-duty

base

Power cord and

cord storage

(not shown)

Lid latch

Drive pin

Lid hinge

Handle hinge

Reversible

slicing/shredding

disc

Drive adapter

Multipurpose

stainless steel

blade

Work bowl

cover with

2-in-1 feed

tube

2-piece

food pusher

7-cup (1.7 L)

work bowl

ENGLISH

FOOD PROCESSOR SAFETY | 3

FOOD PROCESSOR SAFETY

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always

be followed, including the following:

1. Read all instructions.

2. To protect against risk of electrical shock, do not put Food Processor in water or

other liquid.

3. This appliance is not intended for use by persons (including children) with

reduced physical, sensory, or mental capabilities, or lack of experience and

knowledge, unless they are closely supervised and instructed concerning use

of the appliance by a person responsible for their safety. Close supervision is

necessary when any appliance is used by or near children. Children should be

supervised to ensure that they do not play with the appliance.

4. Turn the appliance OFF, then unplug from the outlet when not is use, before

assembling or disassembling parts and before cleaning. To unplug, grasp the

plug and pull from the outlet. Never pull from the power cord.

5. Avoid contacting moving parts.

6. Do not operate any appliance with a damaged cord or plug, or after the

appliance malfunctions, or is dropped or damaged in any manner. Return

appliance to the nearest Authorized Service Center for examination, repair, or

adjustment.

4 | FOOD PROCESSOR SAFETY

FOOD PROCESSOR SAFETY

7. The use of attachments not recommended or sold by KitchenAid may cause re,

electric shock, or injury.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter.

10. Keep hands and utensils away from moving blades or discs while processing

food to reduce the risk of severe injury to persons or damage to the Food

Processor. A scraper may be used, but must be used only when the Food

Processor is not running.

11. Blades are sharp. Handle carefully.

12. To reduce the risk of injury, never place cutting blade or disc on base without rst

putting bowl properly in place.

13. Be certain cover is securely locked in place before operating appliance.

14. Never feed food by hand. Always use the food pusher.

15. Do not attempt to defeat the cover interlock mechanism.

16. Do not ll the bowl above the marked maximum ll line (or rated capacity) to

avoid risk of injury due to damage to the cover or bowl.

SAVE THESE INSTRUCTIONS

ELECTRICAL REQUIREMENTS

This product is designed for household use only.

Voltage: 120 VAC

Frequency: 60 Hz

NOTE: This Food Processor is equipped

with a polarized plug (one blade is wider

than the other). To reduce the risk of

electrical shock, this plug will fit in a

polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse

the plug. If it still does not fit, contact a

qualified electrician. Do not modify the

plug in any way.

ENGLISH

USING THE FOOD PROCESSOR | 5

USING THE FOOD PROCESSOR

ACCESSORIES SELECTION GUIDE

ACTION SETTING FOOD ACCESSORY

Chop Low or Pulse

Cheese

Chocolate

Fruits

Fresh herbs

Nuts

Tofu

Vegetables

Multipurpose stainless steel blade

+

Mince or Purée High or Pulse

Mix Low

Pasta Sauce

Pesto

Salsa

Sauces

Batters

Knead High or Pulse Doughs

Slice

Low

Fruit (soft)

Potatoes

Tomatoes

Vegetables (soft)

Reversible slicing/shredding disc

(slicing side)

+

High

Cheese

Chocolate

Fruits (hard)

Vegetables (hard)

Shred

(ﬁne to medium)

Low

Potatoes

Vegetables (soft)

Reversible slicing/shredding disc

(shredding side)

+

High

Cabbage

Cheese

Chocolate

Fruits (hard)

Vegetables (hard)

FOR DETAILED INFORMATION ON USING THE FOOD PROCESSOR

Visit www.kitchenaid.com/quickstart for additional instructions with videos, inspiring

recipes, and tips on how to use your Food Processor.

6 | USING THE FOOD PROCESSOR

USING THE FOOD PROCESSOR

Before using your Food Processor for the ﬁrst time, wash all parts and accessories either

by hand or in the dishwasher (see the “Cleaning the Food Processor” section). Your Food

Processor is designed so that all accessories may be stored inside the work bowl.

BEFORE FIRST USE

ASSEMBLING THE FOOD PROCESSOR

IMPORTANT: Place the Food Processor on a dry, level countertop with the controls

facing forward. Do not plug in the Food Processor until it is completely assembled.

1

Place the work bowl on the base,

aligning the handle with the raised

button on the right side of the base.

The bowl will click into place and

should be flush against the base

when properly aligned.

2

Place the drive adapter in the work

bowl, lowering it onto the drive pin.

1

Lift up the lid latch to unlock the

cover. Tilt the work bowl cover back

and lift it straight up so that the lid

hinge pulls out of the handle hinge.

2

Remove all parts and accessories

from the work bowl, and lift the food

pusher out of the feed tube.

ENGLISH

USING THE FOOD PROCESSOR | 7

USING THE FOOD PROCESSOR

NOTE: For ease of assembly, install the desired blade or disc before attaching

the work bowl cover.

NOTE: Your Food Processor will not

operate unless the work bowl cover is

fully closed and the work bowl is properly

seated on the base.

3

To attach the work bowl cover, hook

the lid hinge into the handle hinge on

the work bowl and close the cover.

4

Once the work bowl cover is closed,

push the lid hinge down into the

locked position.

INSTALLING THE MULTIPURPOSE BLADE

1

Place the blade on the drive adapter.

Rotate the blade so it falls down to

the base of the adapter.

2

Install the work bowl cover, and be

sure the lid latch is pushed down to

the locked position.

8 | USING THE FOOD PROCESSOR

Alignment

marks

USING THE FOOD PROCESSOR

INSTALLING THE REVERSIBLE SLICING/SHREDDING DISC

1

To slice: Turn the disc so that the

raised slicing blade is facing up.

To shred: Turn the disc so that the

small, raised shredding blades are

facing up.

The disc can be placed in two different

positions: level with the top of the bowl

for processing, and lower, inside of the

bowl, for storage.

NOTE: While the disc will operate in

storage position, it will not perform as

well. Make sure the disc is level with the

top of the bowl for best performance.

2

Hold the disc by its center hub and

lower it onto the drive adapter,

aligning the mark on the center hub

of the disc to the matching mark on

the adapter. When properly placed,

the disc should be level with the top

of the bowl. If the disc falls to the

storage position, lift it out, turn it 90°,

and lower it again.

3

Install the work bowl cover, and be

sure the lid latch is pushed down to

the locked position.

Process

Storage

ENGLISH

USING THE FOOD PROCESSOR | 9

OPERATING THE FOOD PROCESSOR

Before operating the Food Processor, be

sure the work bowl, blades/disc and work

bowl cover are properly assembled on

the base (see the “Assembling the Food

Processor” section).

Rotating Blade Hazard

Always use food pusher.

Keep ngers out of openings.

Keep away from children.

Failure to do so can result in

amputation or cuts.

USING THE FOOD PROCESSOR

1

To turn on, press LOW or HIGH. The

Food Processor will run continuously

and the indicator light will glow.

To turn off, press LOW or HIGH again,

or press OFF/PULSE.

2

To use the Pulse function:

Press OFF/PULSE for short bursts,

or press and hold for longer bursts.

The Pulse function runs at high

speed only. The Food Processor will

turn off when the Off/Pulse button

is released.

3

When finished, press the OFF/PULSE

button. The indicator light will go

out and the blade or disc will slow

to a stop.

4

Wait until the blade or disc comes to

a complete stop before removing the

work bowl cover. Be sure to turn off

the Food Processor before removing

the work bowl cover, or before

unplugging the Food Processor.

10 | USING THE FOOD PROCESSOR

USING THE 2-IN-1 FEED TUBE

USING THE FOOD PROCESSOR

The 2-in-1 feed tube features a 2-piece

food pusher. To slice or shred small items,

insert the 2-piece food pusher into the

feed tube.

Use the small feed tube and pusher to

process small or slender items, like single

carrots or celery stalks.

To slowly drizzle oil into ingredients, just ﬁll

the small pusher with the desired amount

of oil. A small hole in the bottom of the

pusher will drizzle the oil at a constant rate.

2-piece

food

pusher

1

Turn the Food Processor off:

Press the OFF/PULSE button and

unplug the Food Processor before

disassembling.

2

Lift the lid latch to unlock the work

bowl cover, then lift cover to remove.

REMOVING PROCESSED FOODS

3

If using the disc, remove it before

removing the bowl. Holding the disc

by the center hub, lift it straight up.

4

Remove the drive adapter and

multipurpose blade, if using. The

blade will stay in place on the drive

adapter when you remove the

adapter.

ENGLISH

USING THE FOOD PROCESSOR | 11

USING THE FOOD PROCESSOR

5

Lift the work bowl off of the base to

remove food from the bowl with a

spatula.

USING THE MULTIPURPOSE BLADE

To chop fresh fruits or

vegetables:

Peel, core, and/or remove seeds. For more

consistent results, cut food in 1 to 1½-

inch (2.5-3.75 cm) pieces. Process food to

desired size, using Pulse or Low speed.

Scrape sides of bowl, if necessary.

To puree cooked fruits and vegetables

(except potatoes):

Add 1/4 cup (60 mL) liquid from recipe per

cup (235 mL) of food. Process food, using

short pulses, until ﬁnely chopped. Then

process continuously until reaching desired

texture. Scrape sides of bowl, if necessary.

To prepare mashed potatoes:

Shred hot cooked potatoes using the

shredding disc. Exchange shredding disc

for multipurpose blade. Add softened

butter, milk, and seasonings. Pulse three to

four times, 2 to 3 seconds each time, until

potatoes are smooth and milk is absorbed.

Do not overprocess.

To chop dried (or sticky) fruits:

The food should be cold. Add 1/4 cup

(60 mL) ﬂour from recipe per 1/2 cup

(120 mL) dried fruit. Process fruit, using

short pulses, until reaching desired texture.

To ﬁnely chop citrus peel:

With sharp knife, peel colored portion

(without white membrane) from citrus.

Cut peel in small strips. Process until ﬁnely

chopped.

To mince garlic or to chop fresh herbs

or small quantities of vegetables:

With processor running, add food through

the feed tube. Process until chopped. For

best results, make sure work bowl and

herbs are very dry before chopping.

To chop nuts or make nut butters:

Process up to 3 cups (710 mL) of nuts

to desired texture, using short pulses,

1 to 2 seconds each time. For a coarser

texture, process smaller batches, pulsing

once or twice, 1 to 2 seconds each time.

Pulse more often for ﬁner texture. For

nut butters, process continuously until

smooth. Store in refrigerator.

NOTE: Processing nuts and other hard

foods may scratch the surface finish on

the inside of the bowl.

To chop cooked or raw meat, poultry,

or seafood:

The food should be very cold. Cut in

1-inch (2.5 cm) pieces. Process up to

1 pound (455 g) at a time to desired size,

using short pulses, 1 to 2 seconds each

time. Scrape sides of bowl, if necessary.

To make bread, cookie, or cracker crumbs:

Break food into 1½ to 2-inch (3.75-5 cm)

pieces. Process until ﬁne. For larger pieces,

pulse two to three times, 1 to 2 seconds

each time. Then process until ﬁne.

12 | TIPS FOR GREAT RESULTS

TIPS FOR GREAT RESULTS

To slice or shred fruits and vegetables

that are round, such as onions, apples,

and green peppers:

Peel, core, and remove seeds. Cut in halves

or quarters to ﬁt feed tube. Position in feed

tube. Process using even pressure with the

food pusher.

To slice or shred fruits and vegetables

that are small, such as strawberries,

mushrooms, and radishes:

Position food vertically or horizontally in

layers within the feed tube. Fill feed tube

in order to keep food positioned properly.

Process using even pressure with the

food pusher, or use the small feed tube

in the two-piece food pusher. Position

food vertically in the tube and use the

small food pusher to process food.

To slice uncooked meat or poultry,

such as stir-fry meats:

Cut or roll food to ﬁt feed tube. Wrap

and freeze food until hard to the touch,

30 minutes to 2 hours, depending on

thickness of food. Check to be sure you

can still pierce food with the tip of a sharp

knife. If not, allow to thaw slightly. Process

using even pressure with the food pusher.

To slice or shred fruits or

vegetables that are long

and relatively small in diameter, such as

celery, carrots, and

bananas:

Cut food to ﬁt feed

tube vertically or

horizontally, and

pack so that the

food is supported.

It should not be

packed so tightly

that it cannot move freely. Process using

even pressure with the food pusher, or use

the small feed tube in the two-piece food

pusher. Position food vertically in the tube

and use the small food pusher to process

food.

USING THE REVERSIBLE SLICING/SHREDDING DISC

Rotating Blade Hazard

Always use food pusher.

Keep ngers out of openings.

Keep away from children.

Failure to do so can result in

amputation or cuts.

To melt chocolate in a recipe:

Combine chocolate and sugar from recipe

in work bowl. Process until ﬁnely chopped.

Heat liquid from recipe. With processor

running, pour hot liquid through the feed

tube. Process until smooth.

To grate hard cheeses, such as

Parmesan and Romano:

Never attempt to process cheese that

cannot be pierced with the tip of a sharp

knife. You can use the multipurpose

blade to grate hard cheeses. Cut cheese

in 1-inch (2.5 cm) pieces. Place in work

bowl. Process, using short pulses, until

coarsely chopped. Process continuously

until ﬁnely grated. Pieces of cheese can

also be added through the feed tube while

the processor is running.

ENGLISH

TIPS FOR GREAT RESULTS | 13

To slice cooked meat or poultry,

including salami, pepperoni, etc.:

Food should be very cold. Cut in pieces

to ﬁt feed tube. Process food using ﬁrm,

even pressure with the food pusher.

To shred spinach and other leaves:

Stack leaves. Roll

up and stand

up in feed tube.

Process using even

pressure with

the food pusher.

To shred ﬁrm and soft

cheeses:

Firm cheese should

be very cold. For best results with soft

cheeses, such as mozzarella, freeze 10 to

15 minutes before processing. Cut to ﬁt

feed tube. Process using even pressure

with the food pusher.

TIPS FOR GREAT RESULTS

HELPFUL HINTS

• To avoid damage to the blade or motor,

do not process food that is so hard or

ﬁrmly frozen that it cannot be pierced

with the tip of a sharp knife. If a piece

of hard food, such as a carrot, becomes

wedged or stuck on the blade, stop the

processor and remove the blade. Gently

remove food from the blade.

• Do not overﬁll work bowl. For thin

mixtures, ﬁll work bowl up to 1/2 to 2/3

full. For thicker mixtures, ﬁll work bowl

up to 3/4 full. For liquids, the work bowl

should be no more than 2/3 full. When

chopping, the work bowl should

be no more than 1/3 to 1/2 full.

• Position slicing/shredding disc so the

cutting surface is just to the right of the

feed tube. This allows the blade a full

rotation before contacting the food.

• To capitalize on the speed of the

processor, drop ingredients to be

chopped through the feed tube while

the processor is running.

• Different foods require varying degrees

of pressure for best shredding and slicing

results. In general, use light pressure

for soft, delicate foods (strawberries,

tomatoes, etc.), moderate pressure for

medium foods (zucchini, potatoes, etc.),

and ﬁrmer pressure for harder foods

(carrots, apples, hard cheeses, partially

frozen meats, etc.).

• Soft and medium-hard cheese may

spread out or roll up on the shredding

disc. To avoid this, shred only well-chilled

cheese.

• Sometimes slender foods, such as carrots

or celery, fall over in the feed tube,

resulting in an

uneven slice. To

minimize this, cut

food in several

pieces and pack

the feed tube

with the food.

For processing

small or slender

items, the small

feed tube in the

2-piece food

pusher will prove

especially convenient.

• When preparing a cake or cookie batter

or quick bread, use the multipurpose

blade to cream fat and sugar ﬁrst. Add

dry ingredients last. Place nuts and fruit

on top of ﬂour mixture to prevent over-

chopping. Process nuts and fruits, using

short pulses, until blended with other

ingredients. Do not overprocess.

• When shredded or sliced food piles

up on one side of the bowl, stop the

processor and redistribute the food

using a spatula.

14 | CARE AND CLEANING

• When food quantity reaches the bottom

of the slicing/shredding disc, remove

the food.

• A few larger pieces of food may

remain on top of the disc after slicing

or shredding. If desired, cut these by

hand and add to mixture.

• Use the spatula to remove ingredients

from the work bowl.

• Organize processing tasks to minimize

bowl cleanup. Process dry or ﬁrm

ingredients before liquid ingredients.

• To clean ingredients from the

multipurpose blade easily, just empty

the work bowl, replace the lid, and pulse

1 to 2 seconds to spin the blade clean.

• After removing the work bowl cover,

place it upside down on the counter.

This will help keep the counter clean.

• Your Food Processor is not designed

to perform the following functions:

- Grind coffee beans, grains, or

hard spices

- Grind bones or other inedible

parts of food

- Liquefy raw fruits or vegetables

- Slice hard-cooked eggs or room-

temperature meats.

• If any plastic parts should discolor due

to the types of food processed, clean

them with lemon juice.

TIPS FOR GREAT RESULTS

CARE AND CLEANING

CLEANING THE FOOD PROCESSOR

1

Press the OFF/PULSE button, then

unplug the Food Processor before

cleaning.

IMPORTANT: The BPA-free bowl requires

special handling. If you choose to use

a dishwasher instead of hand washing,

please follow these guidelines.

2

Wipe the base and cord with a warm,

damp cloth. Thoroughly dry with

a soft cloth. Do not use abrasive

cleaners or scouring pads. Do not

immerse base in water or other liquid.

3

All parts are top rack dishwasher safe.

Avoid laying the bowl on its side.

Thoroughly dry all parts after washing.

Use gentle dishwashing cycles such

as normal. Avoid high-temperature

cycles.

ENGLISH

TROUBLESHOOTING | 15

4

You can store up to two blades and

two discs as well as the drive adapter

inside of the work bowl when the

Food Processor is not in use. Wrap

the power cord around the cord

storage on the bottom of the base,

then secure the plug by clipping it to

the housing.

CARE AND CLEANING

CLEANING THE FOOD PROCESSOR

NOTE: If washing the food processor

parts by hand, avoid the use of abrasive

cleansers or scouring pads. They may

scratch or cloud the work bowl and cover.

TROUBLESHOOTING

If your Food Processor should

malfunction or fail to operate, check

the following:

1. Is the Food Processor plugged in?

2. Make sure that the bowl and lid are

properly aligned and locked in place.

3. Have you pressed more than one

button at the same time?

4. Unplug the Food Processor, then plug

it back into the outlet.

5. Is the fuse in the circuit to the

Food Processor in working order?

If you have a circuit breaker box, be

sure the circuit is closed.

6. The Food Processor may need to cool

to room temperature.

If the speed light turns off and the

Off/Pulse light flashes, wait until the

Off/Pulse light turns off and retry.

The Food Processor may take from

5 to 15 minutes to cool completely.

7. The motor may be locked.

If the speed light stays on while

the Off/Pulse light flashes, press the

Off/Pulse button to reset the motor.

Food Processor not shredding

or slicing properly:

1. Make sure the raised-blade side of

the disc is positioned face up on the

drive adapter.

2. Make sure ingredients are suitable

for slicing or shredding. See the “Tips

for great results” section.

3. Make sure the disc is positioned in the

process position (near the top of the

bowl), and not the storage position (low

and inside of the bowl).

If the work bowl cover won’t close

when using the disc:

1. Make sure the disc is installed correctly,

and is positioned properly on the drive

adapter.

If the problem is not due to one of the

above items, see the “Warranty and

service” section.

Do not return the Food Processor to the

retailer. Retailers do not provide service.

16 | WARRANTY AND SERVICE

WARRANTY AND SERVICE

KITCHENAID

®

FOOD PROCESSOR WARRANTY FOR

THE 50 UNITED STATES, THE DISTRICT OF COLUMBIA,

PUERTO RICO, AND CANADA

This warranty extends to the purchaser and any succeeding owner for Food Processors

operated in the 50 United States, the District of Columbia, Puerto Rico, and Canada.

Length of Warranty: One Year Full Warranty from date of purchase.

KitchenAid Will Pay

for Your Choice of:

Hassle-Free Replacement of your Food Processor. See

the next page for details on how to arrange for service,

or call the Customer eXperience Center toll-free at

1-800-541-6390.

OR

The replacement parts and repair labor costs to correct

defects in materials and workmanship. Service must be

provided by an Authorized KitchenAid Service Center.

KitchenAid Will

Not Pay for:

A. Repairs when your Food Processor is used

in other than normal single family home use.

B. Damage resulting from accident, alteration,

misuse or abuse.

C. Any shipping or handling costs to deliver

your Food Processor to an Authorized

Service Center.

D. Replacement parts or repair labor costs

for Food Processors operated outside

the 50 United States, District of Columbia,

Puerto Rico, and Canada.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED

TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY

BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD

ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS

OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY

TO YOU.

IF THIS PRODUCT FAILS TO WORK AS WARRANTED, CUSTOMER’S SOLE AND

EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT ACCORDING TO THE

TERMS OF THIS LIMITED WARRANTY. KITCHENAID AND KITCHENAID CANADA

DO NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES. This warranty gives you speciﬁc legal rights and you may also have other

rights which vary from state to state or province to province.

ENGLISH

WARRANTY AND SERVICE | 17

are trademarks in the U.S. and elsewhere. Used under license in Canada.

In the United States and Puerto Rico:

For service information, or to order

accessories or replacement parts, call

toll-free at 1-800-541-6390 or write to:

Customer eXperience Center,

KitchenAid Small Appliances,

P.O. Box 218, St. Joseph, MI 49085-0218

Outside the United States and Puerto Rico:

Consult your local KitchenAid dealer or

the store where you purchased the Food

Processor for information on how to obtain

service.

For service information in Canada:

Call toll-free 1-800-807-6777.

For service information in Mexico:

Call toll-free 01-800-0022-767.

We’re so conﬁdent the quality of our

products meets the exacting standards

of KitchenAid that, if your Food

Processor should fail within the ﬁrst year

of ownership, KitchenAid will arrange

to deliver an identical or comparable

replacement to your door free of charge

and arrange to have your original Food

Processor returned to us. Your replacement

unit will also be covered by our one year

limited warranty.

If your Food Processor should fail within

the ﬁrst year of ownership, simply call our

toll-free Customer eXperience Center at

1-800-541-6390 Monday through Friday.

Please have your original sales receipt

available when you call. Proof of purchase

will be required to initiate the claim. Give

the consultant your complete shipping

address (no P.O. Box numbers, please).

When you receive your replacement

Food Processor, use the carton, packing

materials, and prepaid shipping label to

pack up your original Food Processor and

send it back to KitchenAid.

We’re so conﬁdent the quality of our

products meets the exacting standards

of the KitchenAid brand that, if your Food

Processor should fail within the ﬁrst year

of ownership, we will replace your Food

Processor with an identical or comparable

replacement. Your replacement unit will

also be covered by our one year limited

warranty.

If your Food Processor should fail within

the ﬁrst year of ownership, simply call our

toll-free Customer eXperience Center at

1-800-807-6777 Monday through Friday.

Please have your original sales receipt

available when you call. Proof of purchase

will be required to initiate the claim.

Give the consultant your complete

shipping address.

When you receive your replacement

Food Processor, use the carton, packing

materials, and prepaid shipping label to

pack up your original Food Processor

and send it back to KitchenAid.

WARRANTY AND SERVICE

HASSLE-FREE REPLACEMENT WARRANTY – 50 UNITED STATES,

DISTRICT OF COLUMBIA, AND PUERTO RICO

HASSLE-FREE REPLACEMENT WARRANTY – CANADA

ARRANGING FOR SERVICE AFTER THE WARRANTY EXPIRES,

OR ORDERING ACCESSORIES AND REPLACEMENT PARTS

18 | PIÈCES ET CARACTÉRISTIQUES

PIÈCES ET CARACTÉRISTIQUES

PIÈCES ET ACCESSOIRES

Base robuste

Cordon d’alimentation

et range-cordon

(non illustré)

Loquet du

couvercle

Axe

d'entraînement

Charnière du

couvercle

Charnière de

la poignée

Disque éminceur/

déchiqueteur

réversible

Tige

d'entraînement

Lame

polyvalente en

acier inoxydable

Couvercle du bol

avec goulotte

d'alimentation

2-en-1

Poussoir en 2

parties

Bol de 7

tasses (1,7 L)

SÉCURITÉ DU ROBOT CULINAIRE | 19

FRANÇAIS

SÉCURITÉ DU ROBOT CULINAIRE

CONSIGNES DE SÉCURITÉ

IMPORTANTES

Lors de l’utilisation d’appareils électriques, il faut toujours observer

certaines précautions élémentaires de sécurité, y compris les suivantes :

1. Lire toutes les instructions.

2. Pour éviter tout risque de choc électrique, ne pas immerger le robot culinaire

dans de l’eau ou tout autre liquide.

3. Cet appareil ne convient pas à une utilisation par des personnes (y compris des

enfants) à capacités physiques, sensorielles ou mentales réduites, ou possédant

un manque d’expérience ou de connaissances, à moins qu’elles ne soient

placées sous supervision ou qu’elles aient reçu des instructions concernant

l’utilisation de l’appareil par une personne responsable de leur sécurité.

4. S’assurer que l’appareil est éteint et débranché de la prise murale lorsqu’il n’est

pas utilisé, avant d’y ajouter des pièces ou d’en enlever et avant de la nettoyer.

Pour débrancher, saisir la che et la retirer de la prise. Ne pas tirer sur le cordon

d’alimentation.

20 | SÉCURITÉ DU ROBOT CULINAIRE

SÉCURITÉ DU ROBOT CULINAIRE

5. Éviter tout contact avec les pièces en mouvement.

6. Ne pas faire fonctionner un appareil si le cordon ou la prise est endommagé,

si l'appareil ne fonctionne pas correctement, s'il tombe ou s’il est endommagé

d’une quelconque façon. Retourner l’appareil au centre de service agréé le plus

proche pour examen, réparation ou réglage électrique ou mécanique.

7. L’utilisation d’accessoires non recommandés ou non vendus par KitchenAid peut

causer un incendie, un choc électrique ou des blessures.

8. Ne pas utiliser à l’extérieur.

9. Ne pas laisser le cordon pendre par dessus le bord d’une table ou d’un plan de

travail.

10. Garder les mains et les ustensiles à l’écart des lames ou disques lors de

la préparation des aliments pour éviter tout blessure corporelle grave ou

dommage au robot culinaire. On peut utiliser un grattoir, mais il doit être employé

uniquement lorsque le robot culinaire ne fonctionne pas.

11. Les lames sont aiguisées. Manipuler avec précaution.

12. Pour réduire le risque de blessure, ne jamais placer la lame ou les disques sur la

base sans installer correctement le bol au préalable.

13. S’assurer que le couvercle est bien verrouillé avant de faire fonctionner l’appareil.

14. Ne jamais introduire les aliments à la main. Toujours utiliser le poussoir pour

introduire les aliments.

15. Ne pas tenter d’outrepasser le dispositif de verrouillage du couvercle.

16. Ne pas remplir le bol au-dessus de la ligne de remplissage maximale marquée

(ou de la capacité nominale) an d’éviter tout risque de blessure en cas

d’endommagement du couvercle ou du bol.

CONSERVER CES INSTRUCTIONS

SPÉCIFICATIONS ÉLECTRIQUES

Ce produit est conçu uniquement pour un usage domestique.

Tension : 120 V CA

Fréquence : 60 Hz

REMARQUE : Ce robot culinaire

comporte une fiche polarisée (avec une

lame plus large que l’autre). Pour réduire

le risque de choc électrique, cette fiche

ne peut être insérée dans une prise que

dans un seul sens. Si la fiche ne s’enfonce

pas complètement dans la prise, inverser

la fiche. Si la fiche ne s’introduit toujours

pas, appeler un électricien qualifié. Ne

pas modifier la prise de quelque manière

que ce soit.

La page charge ...

KitchenAid KFP0718L/KFP0718 Food Processors Manuel utilisateur

KitchenAid KFP0718L/KFP0718 Food Processors Manuel utilisateur

dans d''autres langues

Documents connexes