NAPOLEON NEFB24HG-3A Le manuel du propriétaire

EN

W415-1662 / 05.17.16

FR

PG

27

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.16F

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonﬁ replaces.com •[email protected]

SAFETY INFORMATION

!

WARNING

If the information in these instructions

are not followed exactly, a ﬁ re may result

causing property damage, personal injury

or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

$10.00

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 2021

NEFB24HG, NEFB27HG &

NEFB29HG

ELECTRIC FIREPLACE

EN

W415-1662 / 05.17.16

2

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 5

1.3 GENERAL INSTRUCTIONS 5

1.4 RATING PLATE INFORMATION 6

1.5 LABEL LOCATION 6

2.0 LOCATING APPLIANCE 7

2.1 UNPACKING AND TESTING APPLIANCE 7

2.2 GROUNDING APPLIANCE 7

3.0 INSTALLATION 8

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 8

3.2 MINIMUM MANTEL CLEARANCES 8

3.3 FRAMING 9

3.3.1 HARD WIRING INSTALLATION 10

3.3.2 APPLIANCE INSTALLATION 11

4.0 OPERATING INSTRUCTIONS 12

4.1 OPERATING CONTROL PANEL 12

4.2 OPERATING BY REMOTE CONTROL 13

5.0 FINISHING 14

5.1 GLASS DOOR REMOVAL AND INSTALLATION 14

5.2 PLACING GLASS MEDIA 14

5.3 GLASS MEDIA EMBER BED ASSEMBLY REMOVAL 15

6.0 WIRING DIAGRAM 16

7.0 REPLACEMENT PARTS 17

7.1 NEFB24HG OVERVIEW 18

7.2 NEFB27HG OVERVIEW 19

7.3 NEFB29HG OVERVIEW 20

8.0 TROUBLESHOOTING 21

9.0 WARRANTY 23

10.0 SERVICE HISTORY 24

11.0 NOTES 25

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your municipality

for recycling instructions.

Les piles doivent être mises au rebut conformément aux lois et à la réglementation locales. Certaines

piles peuvent être recyclées et acceptées dans votre centre de recyclage local. Renseignez-vous auprès

de votre municipalité au sujet des directives de recyclage.

EN

W415-1662 / 05.17.16

3

1.0 INTRODUCTION

!

WARNING

3.7C

C

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF

CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁ re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before

servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

and are kept clean. The appliance should be inspected before use and at least annually by a qualiﬁ ed

service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and

other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from trafﬁ c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or ﬁ re, or damage the appliance.

• To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or

relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or other electronic components.

EN

W415-1662 / 05.17.16

4

1.1 DIMENSIONS

CEFB24H ILLUSTRATED

CEFB27H ILLUSTRATED

24"

610mm

18 5/8"

473mm

15 3/4"

399mm

12 3/4"

323mm

18"

457mm

9 1/2"

241mm

25 1/8"

639mm

21"

533mm

17 5/8"

448mm

14 5/8"

371mm

11 5/8"

294mm

8 5/8"

219mm

17"

432mm

22 1/8"

563mm

20 1/8"

511mm

26"

660mm

17 1/4"

437mm

14 1/4"

361mm

9 1/2"

241mm

19 1/2"

495mm

27 1/4"

691mm

20 1/8"

510mm

CEFB29H ILLUSTRATED

24"

610mm

27"

686mm

29"

737mm

NEFB24HG ILLUSTRATED

NEFB27HG ILLUSTRATED

NEFB29HG ILLUSTRATED

EN

W415-1662 / 05.17.16

5

4.8B

A.

Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

B.

The appliance may emit a slight, harmless odour when ﬁ rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

C.

If your appliance does not emit heat, consult the operation section of this manual for further

information.

D.

Use with a CSA- or UL-certiﬁ ed surge protector.

E.

Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured

homes when installed according to these instructions.

!

WARNING

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL

ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

1.2 LISTING APPROVALS

This appliance has been tested in

accordance with the CSA Standards

for ﬁxed and location-dedicated

electric room appliances in the United

States and Canada. If you need

assistance during installation, please

contact your local dealer.

NOTE: This appliance must be

electrically wired and grounded

in accordance with local codes

or, in the absence of local codes,

with National Electric Code ANSI/

NFPA 70-latest edition in the United

States or the Canadian Electric

Code, CSA C22.1 in Canada.

Model Number NEFB24HG NEFB27HG NEFB29HG

Description 24" Electric

Fireplace

27" Electric

Fireplace

29" Electric

Fireplace

Voltage 120V AC 120V AC 120V AC

Watts 1500W 1500W 1500W

Amps 15 AMP

Grounded

Circuit

15 AMP Ground-

ed Circuit

15 AMP Ground-

ed Circuit

Appliance Width 24" (610mm) 27" (686mm) 29" (737m)

Appliance Height 17 5/8"

(448mm)

18 5/8" (473mm) 20 1/8" (511mm)

Appliance Depth 8 5/8" (219mm) 9 1/2" (241mm) 9 1/2" (241mm)

Net Weight 31.1lbs (14.1kg) 35.9lbs (16.3kg) 36.4lbs (16.5kg)

Gross Weight (1A) 34.6lbs (15.7kg) 39.7lbs (18kg) 40.8lbs (18.5kg)

Gross Weight (3A) 37lbs (17kg) 44lbs (20kg) 45bs (20.5kg)

1.3 GENERAL INSTRUCTIONS

As with most electronic devices, your new electric ﬁreplace has been designed to operate at temperatures

between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the ﬁreplace to reach room

temperature before turning it on.

EN

W415-1662 / 05.17.16

6

1.4 RATING PLATE INFORMATION

W385-2154

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 2021 /

HOMOLOGUÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 2021

Page 1 of 1

FOYER À ÉLECTRIQUE. HOMOLOGUÉ POUR

INSTALLATION DANS UNE CHAMBRE À

COUCHER, UNE SALLE DE BAIN ET UN STUDIO.

APPROPRIÉ POUR INSTALLATION DANS UNE

MAISON MOBILE.

ELECTRIC FIREPLACE. SUITABLE FOR

BEDROOM AND BED-SITTING ROOM

INSTALLATION. SUITABLE FOR MOBILE

HOME INSTALLATION.

VOLTAGE: 120 VAC TENSION: 120VCA

FREQUENCY: 60Hz FRÉQUENCE: 60Hz

POWER: 1500W PUISSANCE: 1500W

DATE CODE: XXXXX CODE DE DATE:

DESIGNED IN NORTH AMERCIA

BY WOLF STEEL LTD.

MADE IN CHINA

FABRIQUÉ EN CHINE

WOLF STEEL LTD.

24 NAPOLEON ROAD,

BARRIE, ON, L4M 0G8 CANADA

SERIAL NUMBER/NO. DE SÉRIE:

NEFB

MATERIAL: CLASS IIIA-2 PERMANENT LEXAN ADHESIVE LABEL, MINIMUM THICKNESS 0.1MM, 121°C (250°F) RATING

SPECIFICATION: BLACK LETTERING ON SILVER BACKGROUND. MINIMUM FONT SIZE TO BE MINIMUM OF 8.5 PT (3.2mm)

MAX OVERALL SIZE: 6" x 3"

SERIAL NUMBERS TO BE ASCENDING FROM NEFB24HG 019016

TITLE: RATING PLATE NEFB24HG

REVISION:

DWG#: W385-2154

DATE: 04.27.16_H.W.

MODEL / MODÈLE:

NEFB24HG

DESIGN AMÉRIQUE DU NORD

PAR WOLF STEEL LTÉE.

MASTER CONTRACT: 161746

CONTRAT-CADRE: 161746

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to

the model of the appliance.

For rating plate location, see “LABEL LOCATION” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

SAMPLE

1.5 LABEL LOCATION

RATING PLATE WITH SERIAL

NUMBER

NEFB24HG (W385-2154)

NEFB27HG (W385-2155)

NEFB29HG (W385-2156)

WARNING LABEL

(W385-1944)

CAUTION LABEL

(W385-1945)

WIRE DIAGRAM LABEL

(W385-2157)

"DO NOT COVER" LABEL

(W385-1946)

HARD WIRING

LABEL

(W385-2003)

WARNING

LABEL

(W385-1943)

REAR

FRONT

SIDE

"HOT SURFACE"

LABEL

(W385-2017)

ATTENTION LABEL

(W385-2133)

EN

W415-1662 / 05.17.16

7

!

WARNING

2.0 LOCATING APPLIANCE

2.1 UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box and remove the support brackets. Prior to installing the

appliance, remove all packaging material and test to make sure the appliance operates properly by plugging

the power supply cord into a conveniently located 120V,15 Amp minimum grounded outlet.

2.2 GROUNDING APPLIANCE

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

96.1

GROUNDING METHODS

METAL SCREW

(A)

NOT ALLOWED IN CANADA

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

COVER OF

GROUNDED

OUTLET BOX

(C)

(B)

This appliance is for use on 120 volts. The cord has a plug

as shown in (A). An adapter as shown in (C) is available for

connecting three-blade grounding type plugs to two-slot

receptacles. The green grounding plug extending from the

adapter must be connected to a permanent ground such as

a properly grounded outlet box. The adapter should not be

used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove

plug from outlet.

NOTE: Must be connected to a dedicated15 amp circuit. The

use of an extension cord is NOT permitted.

EN

W415-1662 / 05.17.16

8

3.0 INSTALLATION

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high

trafﬁc areas.

NOTE: Follow all National and local electrical codes.

!

WARNING

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID

TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN

CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD

AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT

USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.

USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE

WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE

HAZARD.

DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.

68.5A

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES

Measurements are taken from the glass front.

Bottom 0" Top 0" to 2" (51mm) mantel

Sides 1/4" (6.3mm) Top 3" (76mm) to ceiling

Back 1/4" (6.3mm) Top 1/4" (6.4mm) to enclosure

!

WARNING

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE

HEAT RESISTANT TO PREVENT DISCOLOURATION.

3.2 MINIMUM MANTEL CLEARANCES

NOTE: The control panel switch is located on the upper right hand side of the appliance. Always ensure

this switch remains accessible.

TOP OF APPLIANCE

6"

152mm

8"8"

203mm

MANTEL

1"

25mm

2"

51mm

3"

76mm

4"

102mm

2"

51mm

1/4"

6.3mm

EN

W415-1662 / 05.17.16

9

A. Once the rough opening has been

prepared, and the power has been

routed to the right side of the recess,

the appliance may be installed.

B. The electrical connection must be

made prior to placing the appliance

into position. (See "HARD WIRING

INSTALLATION" section).

Prepare rough in framing following the recommended dimensions in Figure 1. For the corner rough in

framing, follow the recommended dimension in Figure 2.

Select a location that is not prone to moisture and is located at least 36" (914mm) away from combustible

materials such as curtain drapes, furniture, bedding, paper etc.

NEFB24HG NEFB27HG NEFB29HG

A

9" (229mm)

10" (254mm) 10" (254mm)

B

23" (584mm)

26" (660mm) 28" (711mm)

C

17 1/4"

(438mm) + F

18 1/4"

(463mm) + F

19 3/4"

(502mm) + F

J

41"

(1041mm)

44" (1118mm) 46" (1168mm)

K

29" (736mm) 31 1/2"

(800mm)

32 1/2"

(826mm)

L

29" (736mm) 31 1/2"

(800mm)

32 1/2"

(826mm)

L

K

J

B

C

B

A

L

K

J

B

C

B

A

F

FLOOR

(Or mantel base thickness)

Fig. 1

Fig. 2

3.3 FRAMING

A. Remove the securing screw from the electrical cover plate, located on the right hand side of the

ﬁreplace.

B. Add an electrical box connector and feed the supply wires through the 7/8" (22mm) hole.

C. Separate the black, white and green wires that have the wire nuts on them.

D. Remove the wire nuts and secure the black wire (power L1) to the black (power L1) lead of the

power supply. Connect the white wire from the unit to the white (neutral) wire from the power

supply. Connect the green wire to the ground wire.

E. Resecure the cover plate.

EN

W415-1662 / 05.17.16

10

GREEN

BLACK

WHITE

HARD WIRING CONNECTION

If it is necessary to hard wire this appliance, a qualiﬁed electrician must remove the cord connection, and

wire the appliance directly to the household wiring. The wire and power supply breaker must rated for 120V

minimum 15 Amps.

This appliance must be electrically connected and grounded in accordance with local codes, if hard wired.

In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the

current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLAINCE.

GREEN

BLACK

WHITE

NOTE: There are 3 wires from the ﬁreplace junction; white (neutral), black (power L1) and green

(ground) that connect to 120V power supply (breaker panel), see below.

White, Green and

Black wires:

Connect to 120V

power supply.

3.3.1 HARD WIRING INSTALLATION

* NEFB29HG ILLUSTRATED

NOTE: To aid with moving the appliance, leave enough wire so that the appliance can be removed

from the enclosure without disconnecting the power supply. If servicing, shut off power supply.

BLACK

WHITE

BLACK

WHITE

GREEN

GROUND

BLACK

WHITE

WIRE NUT

WALL

SWITCH

POWER

SUPPLY

MARRET

RED

GREEN

THERMOSTAT

(L1)

(N)

(G)

WIRE NUT

(L1)

(N)

(L1)

(N)

Fig. 1

Fig. 2

EN

W415-1662 / 05.17.16

11

3.3.2 APPLIANCE INSTALLATION

A. With two people, lift the appliance up and insert into the opening, keeping a 3/8" (9.5mm) space

between the appliance and ﬂoor base in order to not scratch the ﬂoor surface. Do not push or slide

the bottom of the appliance on the ﬂoor base, see Figure 1.

B. Set the appliance down and into place, see Figure 2.

C. If the appliance does not sit ﬂat on the ﬂoor or mantel base, apply a shim (not supplied) under the

nylon pads and adjust until level.

MANTEL

TABLETTE

APPLIANCE

APPAREIL

1/4"

MANTEL

TABLETTE

APPLIANCE

APPAREIL

STEP 1: LIFT

ÉTAPES 1: SOULEVER

STEP 2: INSERT

ÉTAPES 2: INSÉREZ

STEP 3: SET APPLIANCE

ÉTAPES 3: RÉGLÉ APPAREIL

DO NOT SLIDE APPLIANCE

NE GLISSEZ PAS L'APPAREIL

!

MANTEL

TABLETTE

APPLIANCE

APPAREIL

1/4"

MANTEL

TABLETTE

APPLIANCE

APPAREIL

STEP 1: LIFT

ÉTAPES 1: SOULEVER

STEP 2: INSERT

ÉTAPES 2: INSÉREZ

STEP 3: SET APPLIANCE

ÉTAPES 3: RÉGLÉ APPAREIL

DO NOT SLIDE APPLIANCE

NE GLISSEZ PAS L'APPAREIL

!

MANTEL

F

NOTE: This appliance is equipped with nylon pads located on the bottom four corners. To prevent

damaging the base of the mantel, carefully lift the appliance into the mantel while avoiding contact

with the front edge of the mantel base.

POWER

Turns the appliance ON/OFF.

FLAME & EMBER LIGHT

CONTROL

HEATER CONTROL

DECORATIVE LIGHT

(CEFB29H ONLY)

TIMER

TEMPERATURE

CONTROL

Controls Flame brightness and the Ember Light.

5 Settings

: Flame & Ember off (FO), Ember on but Flame

off (LL), small Flame & Ember (F1), medium Flame &

Ember (F2), brightest Flame and Ember (F3).

Turns the Heater and Blower ON/OFF.

4 Settings: Heater & Blower off (HO), Blower on (BL), low

heat (H1), high heat (H2).

Controls Decorative Light settings.

4 Settings

: Decorative Light off (do), white colour (d1),

auto-cycle from White / Orange / Blue / Orange-Blue /

White-Orange / White-Blue (d2), lock to desired colour

(d3). It will take 8.5 seconds to switch between colours

(on d2 setting).

Timer can be programed to run appliance for specific

lengths of time (30mins. minimum to 6hrs maximum).

Press and hold the Timer button for 5 seconds. This

will change the button to Temperature Control, or vice

versa. There are 7 temperature settings (61

°F, 64°F, 70°

F,

75

°F, 81°F, 85°F and OFF)

F° / C° SWITCH

Hold 5

seconds

To change temperature format, Fahrenheit or Celsius.

Press and hold the Flame button for 5 seconds.

HEATER LOCK

Hold 5

seconds

Heater button can be locked or unlocked by holding the

Heater button for 5 seconds.

Hold 5

seconds

EN

W415-1662 / 05.17.16

12

4.0 OPERATING INSTRUCTIONS

Once the appliance has been plugged into a grounded electrical outlet or hard wired to a dedicated 120V

power supply, it is ready to operate.

ATTENTION: Ensure the house circuit breakers for the power supply are turned on. When initially

connecting the appliance into a power source the unit will perform an LED check. The unit will ﬂash on

and off for 5 seconds.

The Control Panel is located on the top front of the appliance.

4.1 OPERATING CONTROL PANEL

EN

W415-1662 / 05.17.16

13

4.2 OPERATING BY REMOTE CONTROL

!

WARNING

TO AVOID DANGER OF SUFFOCATION KEEP THE PACKAGING BAG AWAY FROM BABIES AND

CHILDREN. DO NOT USE IN CRIBS, BED, CARRIAGES OR PLAY PENS. THIS BAG IS NOT A TOY.

KNOT BEFORE THROWING AWAY.

A. The power button can be used to turn the appliance on/off. Pressing

this button activates the power to the appliance. Pressing the power

button again will turn off the appliance. The ember and log will fade after

4 seconds after turning off the appliance.

B. To adjust the ﬂame brightness and ember log light, press the ﬂame

button . There is one ember log light and three ﬂame brightness

levels to cycle through and then an off setting ( LL, F1, F2, F3 and then

F0).F3 is the brightest ﬂame level, LL is the ember log light only.

C. To control the thermostat function press the thermostat button .

There are 7 temperature settings (61°F, 64°F, 70°F, 75°F, 81°F 85°F and

off). The default setting will display Fahrenheit. Press the thermostat

button to cycle through the settings. Once you have selected the

desired temperature the heater will automatically operate until that

temperature is reached. When the room temperature is 2 degrees lower

than the temperature setting, the heater will turn on.

D. To activate the heater and blower, press the heater button , the blower

will turn on. Press the heater button again to set desired low or high

heat temperature; press the heater button again to turn off the heater.

E. The timer controls all operating modes of the appliance. To activate the

timer, press the timer button , the icon will illuminate and the time

will appear on the LED display. To choose the desired time, continue to

press the timer button, there are 8 settings (30mins,1h, 2h, 3h, 4h, 5h,

6h and off). The ﬁreplace will turn off at the setting time.

F. To activate the decoration light, press the light button .There are

three settings to cycle through and then an off setting (d1, d2, d3 and

then d0). d1 white colour, d2 colour cycles from White / Orange / Blue / Orange-Blue / White-Orange

/ White-Blue. It will take 8.5 seconds to switch from one colour to the next when in d2 setting, d3 will

lock to a desired colour.

G. To turn off the appliance, press the power button once on the remote, or press the power button once

on the control panel on the unit.

NOTE: This hand held remote control must remain within 6 meters or 19 feet of the appliance to be

effective.

NOTE: When operating the remote control, it must be directed towards the front center of the appliance.

EN

W415-1662 / 05.17.16

14

5.0 FINISHING

!

WARNING

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID

RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

5.1 GLASS DOOR REMOVAL AND INSTALLATION

A. Remove the 4 screws off the appliance, as shown.

B. Remove the glass front and place on a soft non-

abrasive surface.

C. Reverse these steps to reinstall the glass front.

!

WARNING

FACING AND/OR FINISHING MATERIAL MUST NOT INTERFERE WITH AIR FLOW THROUGH

AIR OPENINGS, LOUVRES OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR

SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.

BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL

TO THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.

SCREW

5.2 PLACING GLASS MEDIA

A. Remove glass door, see "GLASS DOOR

REMOVAL AND INSTALLATION" section.

B. Sprinkle glass media evenly onto PVC tray.

Ensure glass media stays within the media tray

cavity.

EN

W415-1662 / 05.17.16

15

5.3 GLASS MEDIA EMBER BED ASSEMBLY REMOVAL

SCREW

EMBER

BED

* NEFB27HG ILLUSTRATED

A. Remove glass media from ember tray.

B. Remove the 4 screws, as shown.

C. Lift ember bed up from the appliance

and remove.

SCREW

EN

W415-1662 / 05.17.16

16

6.0 WIRING DIAGRAM

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLAINCE.

TITLE: LABEL, WIRE DIAGRAM (NEFB24/27/29HG) PART #: W385-2157

REVISION:

DATE: 04.27.16_H.W.

MATERIAL: CLASS IIA-1 PERMANENT LEXAN ADHESIVE LABEL, MINIMUM THICKNESS 0.1MM,

TEMPERATURE RATING MINIMUM OF 121°C (250°F)

SPECIFICATION: BLACK LETTERING ON SILVER BACKGROUND

LABEL SIZE: 5 7/8" (150mm) x 4 3/8" (111mm)

PLUG /

FICHE

FAN /

SOUFFLERIE

MOTOR /

MOTEUR

AC-N

AC-L

RLY1 RLY2 RLY3 RLY4

NTC

OUTOUT

OUT

IN

#7

#8

#5

#6

#2 #4

#14

#1

#9

#3

#11

#12

#13

#10

#15

CARTE DE CIRCUIT IMPRIMÉ

MAIN PCB BOARD /

DECORATION /

DÉCORATION

L

N

G

WIRE NUT /

CONNECTEUR

DE FILS

WIRE NUT /

CONNECTEUR

DE FILS

WIRE NUT /

CONNECTEUR

DE FILS

HEATER 700W2 /

CHAUFFERETTE 700W2

HEATER 700W1 /

CHAUFFERETTE 700W1

THERMAL CUT-OFF /

COUPURE

THERMIQUE

DECORATION LIGHT (OPTIONAL) /

DECORATION DE LUMIÈRE(OPTIONNEL)

700W1

700W2

MOTOR /

MOTEUR

FAN /

SOUFFLERIE

T-FUSE /

FUSIBLE

FLAME /

FLAMME

DISPLAY CN3 /

AFFICHAGE

TEMPERATURE

SENSOR /

CAPTEUR DE

EMPÉRATURE

CONTROL PANEL BOARD /

PANNEAU DE CONTRÔLÉ

FLAME LED LIGHT /

LUMIÈRE DEL DE FLAMME

#1 EMBER BED LED /

LIT DE BRAISES DE DEL #1

W385-2157

#2 EMBER BED LED /

LIT DE BRAISES DE DEL #2

EN

W415-1662 / 05.17.16

17

Contact your dealer or the factory for questions concerning prices and

policies on replacement parts. Normally all parts can be ordered through

your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE

ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

• Model and serial number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

FOR FURTHER INFORMATION, CONTACT YOUR AUTHORIZED DEALER.

* PARTS, PART NUMBERS AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT NOTICE.

41.1A

FAILURE TO POSITION THE PARTS

IN ACCORDANCE WITH THIS

MANUAL OR FAILURE TO USE ONLY

PARTS SPECIFICALLY APPROVED

WITH THIS APPLIANCE MAY

RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY.

!

WARNING

For after sales service, please call 1-866-820-8686

7.0 REPLACEMENT PARTS

EN

W415-1662 / 05.17.16

18

NOTE: Care must be taken when removing and disposing of any broken glass or damaged

components. Be sure to vacuum up any broken glass from inside the appliance before operation.

REF.

PART NO.

DESCRIPTION

1

2

3

4

5

6

7

8

REF.

PART NO.

DESCRIPTION

11

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

G105-0006-SER

FRONT GLASS (W/ MOUNTING BRACKET)

G010-0079-SER

W405-0042

G010-0084

W010-3934

G660-0005

W010-3145-SER

PLASTIC FLAME PANEL

BLOWER & HEATER ASSEMBLY

FLAME LED

REFLECTOR

REMOTE CONTROL TRANSMITTER

FRONT HEADER

W435-0059-SER

SYNCHRONOUS MOTOR

W190-0066-SER

PCB BOARD, LED

31

14

15

12

13

CONTROL PANEL, NEFB29H

G010-0080

32

CONTROL PANEL BOARD

33

34

35

3

6

3

7

8

9

10

13

14

2217

G750-0034-SER

WIRE ASSEMBLY

10

G405-0011-SER

EMBER BED LED

9

G190-0004-SER

TEMPERATURE SENSOR

16

G405-0007-SER

NIGHT LIGHT LED

18

17

18

W497-0028-SER

MEDIA TRAY

MKGT

MEDIA KIT, TOPAZ GLASS (1LB)

12

G190-0006-SER

G510-0002-SER

BUMPER, PLASTIC

3

15

3

16

19

W285-0002-SER

FUSE 2 Amp

11

19

STOCKED

YES

7.1 NEFB24HG OVERVIEW

EN

W415-1662 / 05.17.16

19

REF.

PART NO.

DESCRIPTION

1

2

3

4

5

6

7

8

REF.

PART NO.

DESCRIPTION

11

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

G105-0007-SER

FRONT GLASS (W/ MOUNTING BRACKET)

G010-0079-SER

W405-0042

G010-0085

W010-3933

G660-0005

G010-0082-SER

PLASTIC FLAME PANEL

BLOWER & HEATER ASSEMBLY

FLAME LED

REFLECTOR ASSEMBLY

REMOTE CONTROL TRANSMITTER

FRONT HEADER

W435-0059-SER

SYNCHRONOUS MOTOR

W190-0066-SER

PCB BOARD, LED

31

14

15

12

13

CONTROL PANEL, NEFB29H

G010-0080

3

2

CONTROL PANEL BOARD

33

34

35

3

6

3

7

8

9

10

13

14

2217

G750-0034-SER

WIRE ASSEMBLY

9

G190-0004-SER

TEMPERATURE SENSOR

16

G405-0007-SER

NIGHT LIGHT LED

18

17

18

W497-0027-SER

MEDIA TRAY

MKGT

MEDIA KIT, TOPAZ GLASS (1LB)

12

G190-0006-SER

G510-0002-SER

BUMPER, PLASTIC

3

15

3

16

19

W285-0002-SER

FUSE 2 Amp

11

19

STOCKED

20

10

G405-0011-SER

EMBER BED LED

20

W405-0041

#2 EMBER BED LED

YES

NOTE: Care must be taken when removing and disposing of any broken glass or damaged

components. Be sure to vacuum up any broken glass from inside the appliance before operation.

7.2 NEFB27HG OVERVIEW

EN

W415-1662 / 05.17.16

20

REF.

PART NO.

DESCRIPTION

1

2

3

4

5

6

7

8

REF.

PART NO.

DESCRIPTION

11

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

G105-0006-SER

FRONT GLASS (W/ MOUNTING BRACKET)

G010-0079-SER

W405-0042

G010-0086

W010-3932

G660-0005

G010-3145-SER

PLASTIC FLAME PANEL

BLOWER & HEATER ASSEMBLY

FLAME LED

REFLECTOR ASSEMBLY

REMOTE CONTROL

FRONT HEADER

W435-0059-SER

SYNCHRONOUS MOTOR

W190-0066-SER

PCB BOARD, LED

31

14

15

12

13

CONTROL PANEL, NEFB29H

G010-0080

3

2

CONTROL PANEL BOARD

33

34

35

3

6

3

7

8

9

10

13

14

2217

G750-0034-SER

WIRE ASSEMBLY

10

G405-0011-SER

EMBER BED LED

9

G190-0004-SER

TEMPERATURE SENSOR

16

G405-0007-SER

NIGHT LIGHT LED

18

17

18

W497-0026-SER

MEDIA TRAY

MKGT

MEDIA KIT, TOPAZ GLASS (1LB)

12

G190-0006-SER

G510-0002-SER

BUMPER, PLASTIC

3

15

3

16

19

W285-0002-SER

FUSE 2 Amp

11

19

STOCKED

20

G405-0041

#2 EMBER BED LED

YES

NOTE: Care must be taken when removing and disposing of any broken glass or damaged

components. Be sure to vacuum up any broken glass from inside the appliance before operation.

7.3 NEFB29HG OVERVIEW

La page charge ...

NAPOLEON NEFB24HG-3A Le manuel du propriétaire

NAPOLEON NEFB24HG-3A Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents