Marvel 61HK-BB-F-L Mode d'emploi

Marque: Marvel

Modèle: 61HK-BB-F-L

Catégorie: Frigos

Taper: Mode d'emploi

Installation

Operation

and

Maintenance

Instructions

Scientic Freezer

with External Temperature

Display and Control

MS24FA

NOTE

CAUTION

CONTENTS

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

Unpacking your appliance ...................................................3

Remove packaging ........................................................3

Warranty registration .....................................................3

Installing your appliance .................. ...................................4

Select location ...............................................................4

Cabinet clearance ..........................................................4

Front grille ......................................................................4

Leveling legs ..................................................................4

Electrical requirements and grounding ...............................5

Handle installation ...............................................................6

Energy saving tips ...............................................................6

Using the Microsentry II ™ Control .....................................7

Starting your appliance....................................................7

Set temperature ..............................................................7

Appliance operation.........................................................7

Alarms..............................................................................7

Alarm mute.......................................................................7

Turning appliance o........................................................7

Product dimensions ............................................................8

Features and shelving........................................................10

Care and cleaning .............................................................12

Obtaining Service ..............................................................12

Troubleshooting ................................................................13

Commercial product warranty ..........................................14

Appendix A, additional Microsentry II ™ features ...............15

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

Death or serious injury could result if...

NOTE

CAUTION

UNPACKING YOUR APPLIANCE

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take o the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can

be a suocation hazard.

Figure 1

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See gure 1).

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Online registra-

tion available at

www.marvelrefrig-

eration.com

CAUTION

WARNING

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted be-

tween the minimum, 33

⁄4" (85.7 cm), by turning the leveling

leg in (CW ↷) and the maximum, 34

⁄4" (88.3 cm) by turning

the leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

An optional stacking kit is required to stack products.

Failure to use a stacking kit could result in personal

injury. Contact your dealer or Marvel customer service

at 800-223-3900 to order.

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Marvel does not recommend the use

of a custom made grille as air ow may be restricted. (See

Figure 2).

Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

INSTALLING YOUR APPLIANCE

Figure 5

Toe kick screw

Toe kick ( Front Grille)

Figure 6

Grounding Method

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply.

Electrical Requirements

Electrical Requirements: A 115 volt, 15 amp dedicated cir-

cuit is required. A 3 prong grounded receptacle is required.

The unit must be installed according to your local building

codes and ordinances.

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and cause decient opera-

tion.

• This unit should not, under any circumstances, be

installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. See Figure 3.

• Do not use an adapter. See Figure 4.

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Figure 4

NOTE

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Do not remove

ground prong

Figure 3

GROUNDING METHOD AND ELECTRICAL REQUIREMENTS

HANDLE INSTALLATION AND ENERGY SAVING TIPS

Handle Installation

1. Remove the handle, (2) screws, and

⁄32” allen wrench

from the bag shipped inside the cabinet.

2. Locate handle opposite the hinges and secure in place

using the (2) screws and the allen wrench.

(See Figure 7).

Screws

Handle

Figure 7

Right hand hinged

door shown

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your cold appliance next to a hot appli-

ance, (ovens, glassware washers, etc.). heating air

duct, or other heat sources.

2. Install product out of direct sunlight.

3. Ensure the toe grille vents at front of unit beneath door

are not obstructed and kept clean to allow ventilation

for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set-temperature

that provides the proper storage for your stored con-

tents.

11. Set the control to the “o” position if cleaning the unit

requires the door to be open for an extended period of

time.

12. Periodically clean the front grille (toe kick), see page 4.

USING THE MICROSENTRY II ™ CONTROL

NOTE

Starting your appliance

The appliance will begin start up when initially plugged in or

when power resumes after a power outage. If the appliance

has been turned o during use, “OFF” will appear on the

display. To start the appliance from the “OFF” position press

and hold the ON/OFF button for three seconds.

Set temperature

To set the set temperature, press and continue to hold

“SET” button. After one second, set temperature will be

displayed. While holding “SET” button use the “WARMER”

or “COLDER” button to desired set temperature.

Momentarily pressing & releasing “SET” button will access

information menu of control. Refer to appendix A for infor-

mation on this feature.

Appliance operation

The available temperature range of the freezer is -28° to

-9° C.

It may take up to 24 hours for your appliance to reach de-

sired temperature. This will depend on amount of contents

loaded and number of openings and closings of the door.

For best results allow the appliance to “pull down” to de-

sired set temperature before loading. Once contents are

loaded, allow at least 48 hours for temperature to stabilize

before making any adjustments to the set temperature.

Alarms

Your MicroSentry II™ appliance control will monitor ap-

pliance function and alert you with a series of audible and

visual alarms. For all alarm and error codes, the alarm

LED located in the top left corner of the display panel will

illuminate a steady amber. For all alarm and error codes

except condenser cleaning, an audible alarm will sound,

beeping in one (1) second intervals.

• Door Ajar Alarm: If the door has been

left open for over ve (5) minutes, the alarm

will sound and the display panel will ash

“do.” The alarm will stop once the door has been closed.

• High and Low Temperature Alarm: If

your unit reaches an unacceptable tempera-

ture, above or below your set temperature for

a period of greater than 60 minutes, the tem-

perature alarm will sound in one (1) second

intervals. The display panel will ash either “hi” or “Lo” de-

pending upon the condition. “hi” indicates a high tempera-

ture alarm, and “Lo” indicates a low temperature alarm.

The factory preset for the "hi" and "Lo" temperature devia-

tion is +2°C from set temperature for the "hi" and -2°C from

set temperature for the "Lo". If these temperature variations

need to be adjusted, please call Marvel customer service at

800-223-3900 for instructions.

• Temperature Sensor Fault: If the control

detects that the temperature sensor is not

properly functioning, an audible alarm will

sound, and “E1” will ash on the display. Please call

Marvel customer service or your dealer if this error code is

displayed.

• Condenser Needs Cleaning: When the

appliance has reached the recommended

amount of run time for a condenser cleaning,

“cL” will ash on the display as a reminder to clean the con-

denser. No audible alarm is associated with the condenser

clean warning. To clear the alarm:

1) Press and release the SET key until “cnd”

is displayed on the screen.

2) While “cnd” is displayed, press and hold the SET

key. The display will show the number of weeks the

condenser has been operating.

3) Continue to hold the SET key, then press and re

lease the ON/OFF key. The number shown on the

display will be reset to 00.

4) Release the SET key.

5) The display will return to normal operation after a

few seconds with no key presses.

See the “care and cleaning” section for cleaning instruc-

tions.

Alarm Mute

Press any key to mute the audible portion of an alarm.

NOTE-This action will only mute the alarm. If the condi-

tion that caused the alarm continues, the alarm code will

continue to ash and will sound for 20 seconds every 60

minutes.

Turning Appliance O

To turn appliance o, press and hold “ON/OFF” button for

three (3) seconds. “OFF” will appear on the

display.

Additional MicroSentry II™ Features

Refer to Appendix A for details on additional features avail-

able.

Figure 8

Control located

on face of door

Set

Colder Warmer

ON/OFF

Press and Hold Press and Hold

Alarm

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MS24FAS

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

⁄8"

(60.7 cm)

⁄4" to 34

⁄4"

(85.7 to 88.3 cm)

⁄32"

(60.2 cm)

⁄32"

(63.4 cm)

⁄32"

(119.6 cm)

⁄8"

(63.2 cm)

PRODUCT DIMENSIONS

"A"

"B"

"C"

"D"

"E"

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 10).

Figure 9

Figure 9a

Figure 10

* Depth dimension of rough-in opening may vary depend-

ing on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug

is required.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MS24FAS 115V/60Hz/15A

130 lbs

(59.1 kg)

PRODUCT DIMENSIONS

3" to 4"

(7.6 to 10.2 cm)

⁄2"

(54.6 cm)

"H"

"D"

"E"

"G"

"F"

"J"

Figure 11

Figure 13

FEATURES AND SHELVING CONFIGURATIONS

Freezer:

Loading Tips and Suggestions

Your appliance is equipped with 3 adjustable shelves for

exibility of content storage. The shelves can move up or

down to accommodate various content sizes.

24" (61 cm) Wide Models:

Shown with a solid door. Figure 13.

(3) full depth perforated

metal shelf.

Figure 14

Perforated metal shelf

Lock and Key

The lock and key allow you to lock and store contents.

Content Temperature versus Air Temperature

Air temperature moves up and down with door openings

and compressor run and o cycles. Air has little thermal

mass and therefore changes temperature relatively quickly

between on/o cycles. Stored contents have much higher

thermal mass so their temperatures change much slower.

Always measure temperature with a mass weighted sensor

to determine if the contents being stored are at the proper

temperature.

Probe Port

The probe port is a hole from the inside to the outside of

the unit, which is located on the back of the unit. (See

Figure 12). Remove the foil label and foam plug(s) from

the hole in the back of the unit, insert your probe or wires

through the hole in the back of the unit. Seal hole with foam

plug(s).

-Foam plug(s)

Figure 12

Foil label,

remove to

access probe

port hole.

Figure 15

Bottle holder

Bottle Holder

For your convenience a bracket has been provided to

hold your in-house temperature monitoring bottle. On the

MS24FA it is located on the right side of the interior liner

toward the front.

To install or remove a shelf:

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

16b). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Rear tang

(hook) on

shelf

Shelf support

slot

Installed shelf

tang

Make sure your cantilever shelf is secure on the shelf sup-

ports by pressing down on the shelf before loading.

CAUTION

Grasp the shelf by the front with

both hands and rotate the front

of the shelf up, then lift the shelf

up and remove the shelf from the

shelf ladders.

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving the

shelf.

SHELVING CONFIGURATIONS

Figure 16a

Figure 16

Figure 16b

CARE AND CLEANING AND OBTAINING SERVICE

Front Grille

Be sure that nothing obstructs the required air ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is o so as not to adversely aect the appliance's

temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a qualied service technician for replacement

of the LED.

CAUTION

If Service is Required:

• If the product is within the rst year warranty period

please contact your dealer or call Marvel Customer

Service at 800.223.3900 for directions on how to obtain

warranty coverage in your area.

• If the product is outside the rst year warranty period,

Marvel Customer Service can provide recommenda-

tions of service centers in your area. A listing of autho-

rized service centers is also available at www.marvelre-

frigeration.com under the service and support section.

• In all correspondence regarding service, be sure to

give the service number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "A" is provided for recording pertinent information

regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Service Number

Date Warranty Card Sent (Must

be within 10 days of purchase).

Table A

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

Before You Call for Service

If the appliance appears to be malfunctioning, read through

this manual rst. If the problem persists, check the trouble-

shooting guide below. Locate the problem in the guide and

refer to the cause and its remedy before calling for service.

The problem may be something very simple that can be

solved without a service call. However, it may be required

to contact your dealer or a qualied service technician.

TROUBLESHOOTING

Problem Possible Cause Remedy

Appliance not cold enough

(See “Adjusting the temperature" on page 7)

• Control set too warm

• Content temperature not stabilized.

• Excessive usage or prolonged door open-

ings.

• Airow to front grille blocked.

• Door gasket not sealing properly.

• Adjust temperature colder. Allow 24 hours

for temperature to stabilize.

• Allow temperature to stabilize for at least

24 hours.

• Airow must not be obstructed to front

grille. See “clearances” on

page 4.

• Replace door gasket.

Appliance too cold

(See “Adjusting the Temperature” on page 7)

• Control set too cold

• Door gasket not sealing properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Replace door gasket.

No interior light. • Failed LED light assembly or light switch. • Contact a qualied service technician.

Light will not go out when door is closed • Door not activating light switch.

• Failed light switch

• Appliance not level, level appliance, (See

page 4, “leveling legs”

• Contact a qualied service technician.

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• Level appliance, see “Leveling Legs” on

page 4.

• Contact a qualied service technician.

Appliance will not run. • Appliance turned o

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See “Starting your ap-

pliance” on page 7.

• Plug in power cord.

• Check house circuit.

NOTE

Your freezer has been designed to be very energy ecient.

Because of this the storage compartment has an almost air

tight seal. Therefore when accessing contents and closing

the door, the warm air intrusion will collapse due to the cold

compartment temperature creating a slight vacuum inside

the unit. This may make the door harder to open for about

10 seconds until the internal pressure equalizes with the

exterior.

CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call

a qualied service technician immediately. It is possible

that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused

by prematurely turning the unit o without appropriately

managing the excess water run-o.

NOTE

Your product has an automatic defrost feature that utilizes

an electric heater element. Periodically during defrost you

may observe the following:

• Water dripping and running sounds as a result of the

frost melt.

• Sizzling and popping sounds from water dripping on

the heater element.

• A faint reddish glow in the freezer compartment from

the electric heater element.

These are all “normal” operating characteristics related to

refrigeration product incorporating automatic defrost. They

do not represent any product fault or safety issue.

COMMERCIAL PRODUCT WARRANTY

Marvel Refrigeration (Marvel) Limited Warranty

ONE YEAR LIMITED PARTS & LABOR WARRANTY

For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the

product that proves to be defective in materials or workmanship. For products installed and used for normal residential use,

material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.

All service provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless

otherwise specied by Marvel. Service provided during normal business hours.

TWO YEAR LIMITED PARTS & LABOR WARRANTY (MARVEL PROFESSIONAL PRODUCTS)

For two years from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the

product that proves to be defective in materials or workmanship. For products installed and used for normal residential use,

material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.

All service provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless

otherwise specied by Marvel. Service provided during normal business hours.

AVAILABLE THIRD YEAR LIMITED WARRANTY (MARVEL PROFESSIONAL PRODUCTS)

For designated Marvel Professional product, Marvel oers a one year extension of the two year warranty coverage from the date

of purchase, free of charge. To take advantage of this third year warranty, you must register your product with Marvel within 60

days from the date of purchase at marvelrefrigeration.com and provide proof of purchase.

LIMITED FIVE YEAR SEALED SYSTEM WARRANTY

For ve years from the date of original purchase, Marvel will repair or replace the following parts, labor not included, that prove

to be defective in materials or workmanship: compressor, condenser, evaporator, drier, and all connecting tubing. All service

provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless otherwise

specied by Marvel. Service provided during normal business hours.

WARRANTY TERMS

These warranties apply only to products installed in any one of the fty states of the United States, the District of Columbia,

or the ten provinces of Canada. The warranties do not cover any parts or labor to correct any defect caused by negligence,

accident or improper use, maintenance, installation, service, repair, acts of God, re, ood or other natural disasters. The

product must be installed, operated, and maintained in accordance with the Marvel User Guide.

The remedies described above for each warranty are the only ones that Marvel will provide, either under these warranties or

under any warranty arising by operation of law. Marvel will not be responsible for any consequential or incidental damages

arising from the breach of these warranties or any other warranty, whether express, implied, or statutory. Some states do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to

you. These warranties give you specic legal rights, and you may also have other rights which vary from state to state.

Any warranty that may be implied in connection with your purchase or use of the product, including any warranty of

merchantability or any warranty t for a particular purpose is limited to the duration of these warranties, and only extends to ve

years in duration for the parts described in the section related to the ve year limited warranty above. Some states do not allow

limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

• The warranties only apply to the original purchaser and are non-transferable.

• These warranties cover products installed and used for normal residential use only.

• The warranties apply to units operated outside only if designed for outdoor use by model and serial number.

• Replacement water lters, light bulbs, and other consumable parts are not covered by these warranties.

• The start of Marvel’s obligation is limited to four years after the shipment date from Marvel.

• In-home instruction on how to use your product is not covered by these warranties.

• Food, beverage, and medicine loss are not covered by these warranties.

• If the product is located in an area where Marvel factory authorized service is not available, you may be responsible for a

trip charge or you may be required to bring the product to a Marvel factory authorized service location at your own cost and

expense.

• Units purchased after use as oor displays, and/or certied reconditioned units, are covered by the limited one year warranty

only and no coverage is provided for cosmetic defects.

• Signal issues related to Wi-Fi connectivity are not covered by these warranties.

For parts and service assistance, or to nd Marvel factory authorized service near you, contact Marvel Refrigeration:

MarvelRefrigeration.com • [email protected] • +616.754.5601

1260 E. Van Deinse St., Greenville, MI 48838

APPENDIX A, ADDITIONAL MICROSENTRY II ™ FEATURES

Information Menu / Lockout Key

To access the information menu, press the SET key, and

immediately release it.

In the information menu, a 2 or 3 digit code will be dis-

played representing each entry in the information menu.

The rst code displayed will be t1. With each sequential

press and release of the SET key, the following codes will

appear in this order: t1, t2, thi, tLo, cnd, FrM, and Loc.

(The t2 code only appears on the refrigerator).

To view the value of each code, press and hold the SET

key after the desired code is displayed. Additionally,

the WARMER and COLDER keys may be used to scroll

through the menu. To exit the information menu, press

the ON/OFF key, or wait for several seconds with no key

presses.

1) Current Interior Temperature (tI): While

tl is shown on the screen press and hold the

“SET” key to display the current interior tem-

perature.

2) Defrost Sensor Temperature (t2) refrig-

erator only: While t2 is shown on the screen

press and hold the "SET" key to display the

temperature of the defrost sensor.

3) Maximum Stored Temperature (thi): While

thi is shown on the screen, press and hold the

“SET” key to display the maximum recorded

temperature. The temperature is updated every 5 minutes.

To reset the maximum temperature; continue to hold the

SET key, then press and release the ON/OFF key to reset

the maximum temperature. The maximum temperature will

be reset to the current compartment temperature.

It is recommended that thi be reset after the initial pull-

down (24 hours after power on) to clear any residual

values.

4) Minimum Stored Temperature (tLO):

While tLo is shown on the screen, press and

hold the “SET” key to display the minimum

recorded temperature. The temperature is updated every

5 minutes. Continue to hold the SET key then, press and

release the ON/OFF key to reset the minimum temperature.

The minimum temperature will be reset to the current com-

partment temperature. It is recommended that tLo be reset

after the initial pull down (24 hours after power on) to clear

any residual values.

5) Total Operating Time of the Condenser

Since the Last Cleaning (cnd): The operating

time of the condenser since the last cleaning.

The control monitors the operating time of the condenser

fan to determine when the condenser is in need of being

cleaned. While cnd is displayed on the screen, press and

hold SET key to view the value of cnd. The value shown

is the number of weeks the condenser has been operating.

To reset cnd, continue to hold the SET key then press and

release the ON/OFF key. When the control recommends

the condenser be cleaned, a reminder will be displayed on

the screen (see Alarm Codes.) To clear the alarm code, re-

set the value in cnd following the instructions printed above.

6) Firmware Version (FrM): While FrM is

shown on the screen press and hold the "SET"

key to display the version of the rmware.

7) Keypad Lockout Feature (Loc): This fea-

ture is used to prevent accidental changes to

the set temperature, or accidentally turning the unit o.

While Loc is displayed on the screen, press and hold the

SET key.

If “No” is displayed, Lockout feature is o,

and all keys are enabled. If “Yes” is dis-

played, Lockout feature is ON. The ability to turn the unit

on and o, as well as the ability to adjust set temperature

will be disabled. To change the keypad lockout setting,

continue to hold the SET key, then use the WARMER and

COLDER keys to set the desired value.

All specications and product designs subject to change without notice. Such revisions do not entitle

the buyer to corresponding changes, improvements, additions, replacements or compensation for

previously purchased products.

www.marvelrefrigeration.com

1260 E. VanDeinse St.

Greenville MI 48838

800.223.3900

41014576-EN Rev E

1/15/20

Marvel Refrigeration

Instructions

d’installation,

d’utilisation

et d’entretien

Congélateur scientique avec achage et

contrôle de température extérieurs

MS24FA

ATTENTION

REMARQUE

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de malformations et

autres déciences de naissance.

AVERTISSEMENT

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de cancers.

AVERTISSEMENT

CONTENU

Déballage de votre appareil ................................................3

Enlèvement de l’emballage ..............................................3

Enregistrement de la garantie ..........................................3

Installation de votre appareil ...............................................4

Choix de l’emplacement ...................................................4

Écartements par rapport à l’armoire..................................4

Pieds de mise à niveau ............................................4

Raccordement électrique ...................................................5

Installation de poignées .....................................................6

Utilisation de votre contrôle ................................................6

Conseils pour les économies d’énergie .............................7

Dimensions du produit .......................................................8

Caractéristiques ...............................................................10

Entretien et Nettoyage ......................................................12

Obtention de service ........................................................12

Dépannage de votre appareil ............................................13

Garantie sur les produits commerciaux de réfrigération ...14

Annexe A ...........................................................................15

À lire pour éviter des blessures graves voire mortelles...

Importantes instructions de sécurité

Les avertissements et les instructions de sécurité qui ap-

paraissent dans ce guide n’ont pas la prétention de couvrir

toutes les conditions et situations possibles pouvant arriver.

Il faut faire preuve de bon sens, de précautions et de soins,

pour installer, utiliser ou entretenir cet appareil.

Reconnaissance des symboles,

des mots et des étiquettes

concernant la sécurité.

AVERTISSEMENT - Risque possible de décès ou

de blessure grave si vous ne suivez pas les instructions.

AVERTISSEMENT

ATTENTION - Risques ou pratiques dangereuses

pouvant entraîner des blessures individuelles, des dégâts

matériels ou des dommages au produit.

REMARQUE - Information importante pour réaliser une

installation et une utilisation sans problèmes.

Figure 1

AVERTISSEMENT

AVERTISSEMENT - Contribuez à éviter des tragédies

L’emprisonnement d’enfants et leur asphyxie ne sont pas

des problèmes du passé. Des épaves de réfrigérateurs

abandonnés continuent de présenter un danger - même

en restant dehors pour «juste quelques heures».

Si vous devez vous débarrasser de votre vieil appareil

de refroidissement, veuillez suivre ces instructions pour

aider à éviter des accidents possibles.

Avant de jeter votre vieux réfrigérateur ou congélateur :

• Démontez ses portes ou enlevez ses tiroirs.

• Laissez les étagères en place de façon à ce que des

enfants ne puissent pas facilement monter dedans.

ATTENTION

REMARQUE

AVERTISSEMENT

RISQUE DE POIDS EXCESSIF

Utilisez deux personnes ou plus pour déplacer le produit.

Sinon vous pourriez vous blesser.

Enlèvement de l’emballage intérieur

Votre congélateur a été emballé pour l’expédition avec toutes les

pièces pouvant être endommagées par le mouvement solidement

attachées. Enlevez les matériaux d’emballage intérieur et toute

bande maintenant des composants intérieurs en place. Le manuel

de l’utilisateur est envoyé à l’intérieur de l’appareil dans un sac en

plastique, accompagné de la carte d’enregistrement de la garan-

tie, et d’autres articles accessoires.

Important

Conservez votre carton d’emballage jusqu'à ce que votre con-

gélateur ait été complètement inspecté et trouvé en bon état.

S’il présentait des dommages, cet emballage serait nécessaire

comme preuve qu’ils sont survenus durant le transit. Ensuite

veuillez mettre tous ces matériaux d’emballage au rebut d’une

façon responsable.

Note pour le client

Cette marchandise a été soigneusement et complètement inspec-

tée avant de quitter notre usine. La responsabilité pour sa livrai-

son sûre a été assumée par le revendeur à l’acceptation de cette

expédition. Les réclamations pour perte ou dommages survenus

durant le transit sont à adresser au revendeur.

NE RENVOYEZ PAS DE MARCHANDISE ENDOMMA-

GÉE AU FABRICANT – DÉPOSEZ UNE RÉCLAMATION

AUPRÈS DU REVENDEUR.

AVERTISSEMENT - Jetez bien les sacs en plastique qui

représentent un risque de suocation.

AVERTISSEMENT

Si l’appareil a été livré, manipulé ou entreposé dans une posi-

tion autre que debout, pendant une durée quelconque, laissez-le

reposer debout pendant au moins 24 heures avant de la brancher

électriquement. Cela assurera le retour de l’huile au compresseur.

Un branchement immédiat de l’appareil pourrait endommager des

parties internes.

DÉBALLAGE DE VOTRE APPAREIL

Enregistre-

ment en ligne dis-

ponible sur

www.marvelrefrigera-

tion.com

Enregistrement de la garantie

Il est important que vous postiez votre carte

d’enregistrement de garantie immédiatement après avoir

reçu la livraison de votre congélateurs, vous pouvez aussi

l’enregistrer en ligne sur le site www.marvelrefrigeration.

com.

Les informations suivantes

seront nécessaires au moment

de l’enregistrement de votre

appareil:

Numéro de service

Numéro de série

Date d’achat

Nom et adresse du revendeur

Le numéro de service et le numéro de série se trouvent sur la

plaque signalétique qui est située à l’intérieur de l’armoire, du

côté gauche près du haut (Voyez la Figure 1).

ATTENTION

AVERTISSEMENT

Un kit optionnel d’empilage est nécessaire pour empiler des

produits. Le fait de ne pas utiliser de kit d’empilage peut

entraîner une blessure corporelle. Contactez votre revendeur

ou le service à la clientèle de Marvel au 800-223-3900 pour le

commander.

Choix de l’emplacement

Un bon emplacement assurera une performance de pointe pour

votre appareil. Nous recommandons un endroit où l’appareil ne

sera pas exposé directement au rayonnement solaire et restera

écarté de sources de chauage. Pour assurer que les perfor-

mances de votre produit soient au niveau de ses spécications, la

plage de températures recommandée au lieu d’installation sera de

55 à 100°F (13 à 38 °C).

Dégagements par rapport à l’armoire

Une ventilation est nécessaire depuis la section frontale du bas de

l’armoire. Gardez cette zone libre et exempte de toutes obstruc-

tions. Des meubles et comptoirs peuvent être installés autour de

l’unité de façon adjacente dans la mesure où sa grille frontale

restera non obstruée.

Grille frontale

N’obstruez pas la grille frontale. Les ouvertures au travers de la

grille frontale permettent l’écoulement de l’air par l’échangeur

thermique du condenseur. Des restrictions de ce ux d’air vont

augmenter la consommation d’énergie et aecter sa capacité de

refroidissement. C’est pourquoi il est important que cette zone ne

soit pas obstruée et soit maintenue propre. Marvel recommande

de ne pas utiliser de grilles personnalisées, car l’écoulement d’air

en serait diminué (Voyez la Figure 2).

Pieds de mise à niveau

Des pieds réglables aux angles avant et arrière de l’armoire

doivent être ajustés pour qu’elle soit fermement positionnée

au sol et bien d’aplomb, d’un côté à l’autre et d’avant en

arrière. La hauteur totale de votre appareil Marvel peut être

ajustée entre le minimum 33

⁄4 po (85,7 cm) (en vissant les

pieds de mise à niveau CW ↷) et le maximum 34

⁄4 po (88,3

cm) (en dévissant les pieds de mise à niveau CCW ↶) des.

Pour régler ces pieds de mise à niveau, placez l’appareil

sur une surface solide, en protégeant le sol en dessous

pour ne pas le rayer. Avec l’aide d’une autre personne, in-

clinez vers l’arrière de l’appareil pour accéder aux pieds de

mise à niveau de l’avant. Levez ou abaissez ces pieds à la

hauteur requise en les tournant. Répétez la procédure pour

les pieds arrière en inclinant le cave à vin vers l’avant en

faisant attention. Sur une surface plane, vériez le niveau

de l’appareil et ajustez les pieds en conséquence.

Les vis de la grille frontale peuvent être desserrées et la

grille ajustée à la hauteur voulue. Quand le réglage est fait

resserrez les vis de la grille frontale (Voyez la Figure 5).

Pieds de mise à

niveau avant

Figure 2

Pieds de

mise à niveau

arrière

Grille frontale,

gardez cette

zone dégagée.

INSTALLATION DE VOTRE APPAREIL

La page charge ...

Marvel 61HK-BB-F-L Mode d'emploi

Marque: Marvel

Modèle: 61HK-BB-F-L

Catégorie: Frigos

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel 61HK-BB-F-L User guide

Marvel 61HK-BB-F-L Mode d'emploi

Marvel 61HK-BB-F-L Mode d'emploi

dans d''autres langues

Documents connexes