Uniden UC100B-DC Le manuel du propriétaire

Taper
Le manuel du propriétaire
1
UNIDEN SECURITY CLOUD
CAMERA USER MANUAL
Compatible Models - UC100B/DC
IMPORTANT SAFETY INSTRUCTIONS
Do not connect multiple devices to a single power adapter. The
adapter may overload and cause overheating or a re hazard.
Verify the power supply voltage is correct before using the camera.
Position the power supply where it will not come in contact with liquid.
Keep it dry.
Do not drop the camera or subject it to physical shock.
Do not aim the camera at the sun or other bright places. Doing so may
aect sensor life.
It is the installer’s and/or end user’s responsibility to properly congure
security settings.
2
LEGAL DISCLAIMER
Surveillance laws very by state and local jurisdictions. Check all relevant
laws in your area before using this product to ensure that your use is in
compliance with applicable laws. Uniden is not liable in the event that this
product is used for illegal purposes.
If the camera does not work properly, contact www.uniden.com for
assistance.
Should any statements in this manual conict with applicable laws, the
applicable laws take precedence.
PARTS OF THE CAMERA
FRONT
3
REAR
NO. DESCRIPTION NO. DESCRIPTION
1 Mounting Base 7 Memory Card Slot
2 Back Case 8 Power Supply
Interface
3 Sun Shield 9 10/100M Self-
Adaptive Ethernet
Interface
4 Lens 10 PoE Cable
5 Adjusting Nut 11 GND Screw
6 WPSS/RESET Button
INSTALLATION
CONSIDERATIONS
Make sure the device in the package is in good condition and all the
assembly parts are included.
The standard power supply is 12VDC (±25%) or PoE (802.3 af). Verify
that your power supply matches your camera.
Make sure all the related equipment is o during the installation.
Make sure that the wall or ceiling is strong enough to hold the weight
of the camera and the base.
4
Do not place the camera in areas where it will be exposed to extreme
heat or cold. Operating temperature range is -22°F to +140°F (-30°C
to +60°C).
To prevent IR reection:
Dust or grease on the camera lens will cause IR reection. If there is
dust or grease on the lens, clean it with clean soft cloth and isopropyl
alcohol.
Make sure that there is no reective surface too close to the camera
lens. The IR light from the camera may reect back into the lens,
causing reection.
INSTALL MEMORY CARD
1. Unscrew the cover to expose the memory card slot.
2. Insert the memory card.
3. To remove the memory card, press it inwards until it clicks. Release it
and the memory card ejects.
4. Screw the cover back on the camera.
CEILING MOUNT
Illustrations may vary slightly from actual camera.
1. Attach the drill template in the desired mounting location.
5
2. Drill the screw holes into the ceiling according to the drill template.
3. Route the cables and x the mounting base on the ceiling with three
screws (included).
4. Adjut surveillance angle. Loosen one tilting adjustment screw and
adjust as needed. Tighten the screw.
COMPLIANCE
FCC PART 15
The equipment has been tested and found to comply with the limits
for a Class B device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
6
turning the equipment o and on, the user is encouraged to try to correct
the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party
responsible for compliance could void your authority to operate the
equipment.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Tout changement ou modication non approuvé expressément par
la partie responsable pourrait annuler le droit à l’utilisateur de faire
fonctionner cet équipement. Tout changement ou modication doit être
approuvé par écrit par Uniden.
Avis de conformité à la FCC : Ce dispositif a été testé et s’avère
conforme à l’article 15 des règlements de la Commission fédérale
des communications (FCC). Ce dispositif est soumis aux conditions
suivantes: 1) Ce dispositif ne doit pas causer d’interférences nuisibles et;
2) Il doit pouvoir supporter les parasites qu’il reçoit, incluant les parasites
pouvant nuire à son fonctionnement.
In order to comply with FCC RF Exposure requirements, this device must
be installed to provide at least 7.9 in (20 cm) separation from the human
body at all times.
IC
This device complies with Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
7
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Cet appareil est conforme aux normes CNR d’Industrie Canada destinés
aux appareils radio exempts de licence. Son fonctionnement est soumis
aux deux conditions suivantes :
1) Cet appareil ne doit pas causer d’interférences nuisibles et;
2) Il doit pouvoir accepter les interférences, incluant celles pouvant nuire
à son fonctionnement normal.
In order to comply with FCC/ISED RF Exposure requirements, this device
must be installed to provide at least 7.9 in. (20 cm) separation from the
human body at all times.
An de se conformer aux exigences d’exposition RF FCC/ISED, ce
dispositif doit être installé pour assurer une séparation d’au moins 20 cm
du corps humain à tout moment.
ONE-YEAR LIMITED WARRANTY
Important: SAVE YOUR RECEIPT! Evidence of original purchase
is required for warranty service.
WARRANTOR: Uniden America Corporation (“Uniden”) ELEMENTS OF
WARRANTY: Uniden warrants, for ne year, to the original retail owner,
this Uniden Product to be free from defects in materials & craftsmanship
with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall
terminate & be of no further eect 12 months after the date of original
retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modied, altered, or used
as part of any conversion kits, subassemblies, or any congurations
not sold by Uniden, (C) improperly installed, (D) serviced or repaired by
someone other than an authorized Uniden service center for a defect or
malfunction covered by this warranty, (E) used in any conjunction with
equipment or parts or as part of any system not manufactured by Uniden,
or (F) installed or programmed by anyone other than as detailed by the
owner’s manual for this product.
8
STATEMENT OF REMEDY: In the event that the product does not
conform to this warranty at any time while this warranty is in eect,
warrantor will either, at its option, repair or replace the defective unit &
return it to you without charge for parts, service, or any other cost (except
shipping & handling) incurred by warrantor or its representatives in
connection with the performance of this warranty. Warrantor, at its option,
may replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE &
ENTIRE WARRANTY PERTAINING TO THE PRODUCT & IS IN LIEU
OF & EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER
OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not
allow this exclusion or limitation of incidental or consequential damages
so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specic legal rights, & you
may also have other rights which vary from state to state. This warranty is
void outside the United States of America & Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY:
If, after following the instructions in the owner’s manual you are certain
that the Product is defective, pack the Product carefully (preferably in its
original packaging). The Product should include all parts & accessories
originally packaged with the Product. Include evidence of original
purchase & a note describing the defect that has caused you to return it.
The Product should be shipped freight prepaid, by traceable means, to
warrantor at:
Uniden America Service
C/O Saddle Creek
743 Henrietta Creek Rd., Suite 100
Roanoke, TX 76026
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Uniden UC100B-DC Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues