Hampton Bay LDS-BF3002 Mode d'emploi

Marque: Hampton Bay

Modèle: LDS-BF3002

Taper: Mode d'emploi

Ce manuel convient également à

LDS-BF3003

USE AND CARE GUIDE

COLOR CHANGING LED VENTILATION FAN

Questions, problems, missing parts? Before returning to the store,

call Hampton Bay Customer Service

8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-800-841-1350

HAMPTONBAY.COM

THANK YOU

We appreciate the trust and conﬁdence you have placed in Hampton Bay through the purchase of this ventilating bath fan. We strive to

continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.

Thank you for choosing Hampton Bay!

Item #317297138/317297139

Model #LDS-BF3002/LDS-BF3003

Table of Contents ........................................................... 2

Safety Information.......................................................... 2

................................................... 4

Typical Installation.......................................................... 4

Wiring Diagram............................................................... 4

Warranty .......................................................................... 5

LIMITED LIFETIME WARRANTY ................................................5

What is Covered......................................................................5

Pre-installation................................................................ 5

Planning Installation................................................................ 5

Tools Required........................................................................5

Package Contents...................................................................6

Installation - New Construction with Flex Bracket ..... 7

Installation - Existing Construction............................ 11

Light Mode Operation .................................................. 13

Compatility ................................................................... 13

Installation - New Construction without Flex Bracket 9

Care and Maintenance................................................. 14

Troubleshooting............................................................ 14

Table of Contents

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the

product.

1. Always disconnect the power supply prior to servicing the fan, motor or junction box.

2. Follow all local building, safety and electrical codes as well as NEC (National Electrical Code) and OSHA (Occupational Safety and Health Act).

3. Electric Service supply must be 120 volts, 60 hertz.

4. This product must properly connect to the grounding conductor of the supply circuit.

5. Do not bend or kink the power wires.

6. Do not use this fan with any solid state control device, such as a remote control, dimmer switch, or certain timers. Mechanical timers are not

solid state devices.

7. Do not install in a ceiling with insulation greater than R50.

8. Duct work should be installed in a straight line with minimal bends.

9. Duct work size must be the same size as the discharge and should not be reduced. Reducing the duct size may increase fan noise.

10. To ensure the performance, please use the recommended dimmers in the list if necessary.

WARNING:

CAUTION: For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

CAUTION: Not for use in cooking areas.

CAUTION:

1. Use this unit in the manner intended by the manufacturer. If you have any questions. Please call customer service.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

warning tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualiﬁed personis) in accordance with all apolicable codes and standards, including

ﬁre-rated construction.

4. Sufﬁcient air is needed for proper combustion and exhausting of gases through the ﬂue (chimney) of fuel burning equipment to prevent backdrafting.

Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and local code authorities.

5. When cutting or drilling into the wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault

Circuit Interrupter) – protected branch circuit.

8. FOR USE IN ONE- AND TWO-FAMILY DWELLINGS ONLY.

9. TYPE IC-INHERENTLY PROTECTED

10. FOR USE IN NON FIRE RATED INSTALLATIONS ONLY.

11. SUITABLE FOR DAMP LOCATIONS

HAMPTONBAY.COM

Please contact 1-800-841-1350 for further assistance.

Safety Information

Product Description : Bathroom Exhaust Fan with LED Light

Model Number LDS-BF3002, LDS-BF3003

Trade NameHAMPTON BAY

Responsible Party 300 Technology Court SE Suite 100, Smyrna, GA 30082

Tel.: (678) 293-8382

Testing Laboratory : Intertek Testing Services Shanghai

Building No.86, 1198 Qinzhou Road (North), Caohejing Development Zone, Shanghai 200233, China

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC Part 15Supplier's Declaration of Conformity

Typical Installation

Wiring Diagram

SPECIFICATIONS SPECIFICATIONS

Power consumption: Fan 38W, Light 20W

Voltage: 120 V, 60 Hz

Airﬂow: 160 CFM Main light: 1500lm Night light: 2200K

Weight: 13.01 lbs.

Duct diameter: 6 in. Ceiling Opening Dimension Requirements: 12.17 in. (L) x 11 in. (W).

Sound output: 1.1 Sones

The ducting from this fan to the outside of the

energy use of the fan. Use the shortest, straightest

duct routing possible for best performance, and

avoid installing the fan with smaller ducts than

recommended. Insulation around the ducts can

reduce energy loss and inhibit mold growth. Fans

installed with existing ducts may not achieve

WARNING: Wiring must comply with all applicable electrical

codes. Turn OFF power before removing or installing connectors

WARNING: COPPER TO COPPER ONLY. Do not use Aluminum wire.

Roof cap (with

built-in damper)

Caulk

termination

to duct

Wall cap

(with

built-in

damper)

Properly insulate

around fan to

minimize building

heat loss and gain

Fan housing

Seal any gap around

fan housing 2-3 foot straight run

before elbow

duct helps alignment

and absorbs sound

fan

fan switch

(purchased separately)

light switch

(purchased separately)

120V line ACGround

black

white

ground

lightfan

black

The LED light

can be

connected to a

dimmer switch

The FAN wires

cannot be

connected to a

dimmer switch

LIMITED LIFETIME WARRANTY

WHAT IS COVERED

of charge, postage-paid at their option. This warranty does not cover products that have been abused, altered, damaged, misused, cut or worn. This

warranty does not cover use in commercial applications. Use only manufacturer-supplied genuine warranty repair replacement parts to repair this fan. Use of

non-genuine repair parts will void your warranty. The manufacturer DISCLAIMS all other implied or express warranties including all warranties of merchant-

This warranty is limited to the replacement of defective parts only. Labor charges and/or damage incurred during installation, repair, replacement as well

as incidental and consequential damages connected with the above are excluded. Any damage to this product as a result of neglect, misuse, accident,

improper installation or use other than the purpose SHALL VOID THIS WARRANTY. Shipping costs for return product as part of a claim on the warranty

must be paid for by the customer.

Contact the Customer Service Team at 1-800-841-1350 or visit www.HAMPTONBAY.com.

Warranty

Pre-installation

PLANNING INSTALLATION

Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents. If

any part is missing or damaged, do not attempt to assemble the product.

WARNING: Turn off electricity at breaker box before beginning

installation.

Carefully remove the unit from the carton.

for proper ventilation.

Inspect duct work and wiring before proceeding with installation.

Before installation, provide inspection and future maintenance access at a location that will not interfere with installation work.

NOTE: Installation may vary depending on how the previous bath fan

was installed. Supplies necessary for the installation of your bath fan are

not all included. However, most are available at your local home

improvement or hardware store.

TOOLS REQUIRED (not included)

Claw

hammer

Drill

bits

Flathead

screwdriver

Duct Pliers

tape

Phillips head

screwdriver

Utility

knife

Electric Goggles Gloves

drill

HAMPTONBAY.COM

Please contact 1-800-841-1350 for further assistance.

Pre-installation (continued)

PACKAGE CONTENTS

Part Description Quantity

A Fan housing 1

B1 or B2 Grille with light 1

C Duct connector 1

D Joist screw 4

E Short screw 1

F Wire cover 1

G Flex bracket 1

H Cut-hole template 1

I Drywall cover board 1

(Model LDS-BF3002 Only)

(Model LDS-BF3003 Only)

① Tape the template to the ceiling.

Plier les onglets du modèle.

② Insert jab saw to cut or pencil to mark.

Insérez les languettes dans la fente du boîtier du ventilateur.

③ Use template edge to guide saw or pencil.

Fixer le gabarit avec du ruban adhésif.

Drywall Cutout Template

Easy installation

Gabarit de découpe pour

cloison sèche Installation facile

TEMPLATE

MODÈLE

Grille enclosed – Do not throw away

Installation instructions are included within the grille’s packaging

Grille fermée - Ne pas jeter

Les instructions d'installation sont incluses dans l'emballage de la grille.

Caution/Attention:

Fan Housing Covering Template

Gabarit de recouvrement

du boîtier du ventilateur

3.Secure the template with tape

Fixer le gabarit avec du ruban adhésif

To protect the fan housing from painting, please apply this fan

housing covering template to the housing as shown above.

Pour protéger le boîtier du ventilateur de la peinture, veuillez

appliquer ce gabarit de recouvrement du boîtier du ventilateur

sur le boîtier comme indiqué ci-dessus.

Installation / l' installation

1.Fold the tabs of template

Plier les onglets du modèle

2.Insert the tabs to the slot of fan housing

Insérez les languettes dans la fente du boîtier du ventilateur.

Installation - New Construction with Flex Bracket

CAUTION:  Make sure power is switched off at

service panel before starting installation.

 Wear gloves during installing to help protect your

hands from injury.

NOTE: Ceiling mount only.

1Install the flex bracket

 Bend down 4 tabs on the side of flex bracket (G) for

positioning, pre-install the flex bracket to joists by

using 2 screws (D) on one side.



Adjust the length of flex bracket (G) to fit the spacing

between the joists (12in. to 22in.). Attach the flex

bracket with the other 2 screws (D).

Please make sure the bottom of the flex bracket will

be flush with the bottom of the joists.

2Adjust the tabs of fan housing

 Pull the 4 tabs (AA) of the fan housing into the vertical position.

3Install the fan housing on bracket

 Align the 4 tabs (AA) on the fan housing through the slots on the

flex bracket (G). Then insert the tabs through the slots until the

fan housing (A) sitting on the flex bracket (G).

 Then bend the tabs (AA) to both sides to attach the fan housing

firmly on the flex bracket (G).

Please remove the tape, which protects

the damper during shipping and

installation, from the duct adaptor as

shown below.

IMPORTANT:

HAMPTONBAY.COM

Please contact 1-800-841-1350 for further assistance.

Installation - New Construction (continued)

4Connect the wire



5Connect the duct



Connect a 6 in. circular duct (not supplied) and vent to the

duct connector. Secure it with duct tape (not supplied) or a

clamp (not supplied) to make the connection secure and

air tight.

Turn on the power source. Check the fan for any abnormal

sound or vibration.

7Select the light color

 Select desired LED color temperature by sliding the toggle

switch on the back of the grille (B).

CAUTION: If the electrical wires do not match the colors

listed, you must determine what each house wire represents

before connecting. You may need to consult an electrical

contractor to determine safely.

NOTE: Attach the 1/2" ROMEX connector or 1/2 "Flexible Metal Conduit

connector (supplied by others) to wiring compartment cover and lock in

place with 1/2 lock nut included with connector.

5000K

4000K

3000K

5000K

4000K

3000K

Green to Green White

Black

Loosen the short screw (E) and remove the wire cover (F).

Pull the house wires through the knockout of wire cover (F).

Using the quick connectors to connect 120 V AC house

wiring from the wall switch to the fan as shown in the

wiring diagram on page 3.

Carefully push the connected wires back into the wiring

compartment of the fan housing (A). Reattach the wire

cover (F) and attach it firmly with the short screw (E).

Ground- Green or copper wire

Neutral-White to White wire

Line-Black to Black wire

NOTE: If you have to connect to 4in.

circular duct, please use a 6in. to 4in.

duct adapter (not supplied).

CAUTION: After checking the

fan, please remember to turn

off the power before next

installation step.

6Finish the ceiling work

 After electrical and construction inspection is completed,

the dry wall ceiling can be installed.



Cut the ceiling hole with the cut-hole template (H) or the

size 11*12.17inch (280*309mm). Ceiling hole should be

aligned with the inside edge of fan housing.

TEMPLATE

Important: Cover and seal up all gaps with duct tape

NOTE: That it is common practice in heating and ventilation

systems using sheet metal ductwork and ﬁttings or ﬂexible duct

work tubing to use duct tape or aluminum tape to ensure air

tight seals and improve efﬁciency.

12.17inch

11inch

Duct tape Duct tape Gaps

HAMPTONBAY.COM

Please contact 1-800-841-1350 for further assistance.

Installation - New Construction without Flex Bracket

1Remove the duct connector and wire cover

2Mount the housing to the joist



Bend down 2 tabs (BB) on outside of housing to locate

and position against bottom of joist for proper position.

Secure fan housing (A) through mounting keyholes on

bracket with with 4 screws (D). Make sure bottom of

fan housing will be flush with finished ceiling.

8Install the grille with light



Attach the grille by squeezing one spring together and inserting

the springs into the spring guides in the fan housing (A) firstly.

Connect LED wire to the plug in the fan housing.

Then insert another spring and push the grille (B) up against

the ceiling.

Check that the installation is secure and safe from falling objects.



To remove duct connector, pull up on the finger latch, then slide

the duct connector left until until it is removed from the fan

housing (A).

Loosen the short screw (E) and remove the wire cover (F).

Installation - New Construction (continued)

NOTE: Ceiling mount only.

Finger latch

Plug

CAUTION:  Make sure power is switched off at

service panel before starting installation.

 Wear gloves during installing to help protect your

hands from injury.

Please remove the tape, which protects

the damper during shipping and

installation, from the duct adaptor as

shown below.

IMPORTANT:

Installation - New Construction(continued)

4Connect the duct



Connect a 6 in. circular duct (not supplied) and vent to the duct

connector. Secure it with duct tape (not supplied) or a clamp

(not supplied) to make the connection secure and air tight.

Insert the duct connector back to the fan housing (A) follow the

guide slot from left to right. And it will be in place with a “click”

sound. Please secure it tightly.

5Select the light color

 Select desired LED color temperature by sliding the toggle

switch on the back of the grille (B).

5000K

4000K

3000K

5000K

4000K

3000K

7Install the grille with light



Attach the grille by squeezing one spring together and inserting

the springs into the spring guides in the fan housing (A) firstly.

Connect LED wire to the plug in the fan housing.

Then insert another spring and push the grille (B) up against the ceiling.

Check that the installation is secure and safe from falling objects.

Plug

3Connect the wire



Green to Green White

Black

Pull the house wires through the knockout of wire

cover (F). Using the quick connectors to connect

120 V AC house wiring from the wall switch to the

fan as shown in the wiring diagram on page 3.

Carefully push the connected wires back into the

wiring compartment of the fan housing (A). Reattach

the wire cover (F) and attach it firmly with short screw (E).

Ground- Green or copper wire

Neutral-White to White wire

Line-Black to Black wire

NOTE: If you have to connect to

4in. circular duct, please use a 6in.

to 4in. duct adapter (not supplied).

NOTE: Attach the 1/2" ROMEX connector or 1/2 "Flexible Metal Conduit

connector (supplied by others) to wiring compartment cover and lock in

place with 1/2 lock nut included with connector.

6Finish the ceiling work

 After electrical and construction inspection is completed,

the dry wall ceiling can be installed.



Cut the ceiling hole with the cut-hole template (H) or the

size 11*12.17inch (280*309mm). Ceiling hole should be

aligned with the inside edge of fan housing.

TEMPLATE

Important: Cover and seal up all gaps with duct tape

NOTE: That it is common practice in heating and ventilation

systems using sheet metal ductwork and ﬁttings or ﬂexible duct

work tubing to use duct tape or aluminum tape to ensure air

tight seals and improve efﬁciency.

12.17inch

11inch

Duct tape Duct tape Gaps

NOTE: MAKE SURE ONE EDGE OF THE OPENING IS FLUSH

WITH THE JOIST FOR INSTALLATION.

HAMPTONBAY.COM

Please contact 1-800-841-1350 for further assistance.

Installation - Existing Construction

1Remove the existing fan



Remove the old fan from the ceiling.

3Remove the duct connector and wire cover



To remove duct connector, pull up on the finger latch, then slide

the duct connector left until it is removed from the fan housing (A).

Loosen the short screw (E) and remove the wire cover (F). F

Ceiling

4Place the fan housing

 Place the fan housing (A) inside the ceiling through the hole.

And then place on the side. Shown as in picture.

Finger latch

Roof cap (with

built-in damper)

Caulk

termination

to duct

Wall cap

(with

built-in

damper)

2-3 foot straight run

before elbow

CAUTION:  Make sure power is switched off at

service panel before starting installation.

 Wear gloves during installing to help protect your

hands from injury.

5Connect the wire



 E

Green to Green White

Black

Pull the house wires through the knockout of wire cover (F).

5 Using the quick connectors to connect 120 V AC house

wiring from the wall switch to the fan as shown in the

wiring diagram on page 3.

Carefully push the connected wires back into the wiring fan

housing (A). Reattach the wire cover (F) attach it firmly with

the short screw (E).

Ground- Green or copper wire

Neutral-White to White wire

Line-Black to Black wire

Please remove the tape, which protects

the damper during shipping and

installation, from the duct adaptor as

shown below.

IMPORTANT:

2Ceiling cut out work

 Measure the opening to ensure it is large enough to

accommodate the new fan body (A) (11 in. x 12.17 in.).

 If this fan is not replacing an old fan, be sure to cut a

11 in. x 12.17 in. opening for the fan body (A).

NOTE:  Wear safety goggles to prevent getting dust,

falling insulation or other debris into your eyes, nose

and mouth.

 Carefully cut open the ceiling hole with out cutting into

electrical or gas or water lines that may not be visible.

12.17inch

11inch

NOTE: Attach the 1/2" ROMEX connector or 1/2 "Flexible Metal Conduit

connector (supplied by others) to wiring compartment cover and lock in

place with 1/2 lock nut included with connector.

Installation - Existing Construction(continued)

8Adjust the inserts of fan housing

 Pull the 4 tabs (AA) of the fan housing into the

vertical position.

NOTE: If you have to connect to 4in. circular duct, please use a 6in.

to 4in. duct adapter (not supplied).

12.17inch

11inch

6Connect the duct



Connect a 6 in. circular duct (not supplied) and vent to

the duct connector. Secure it with duct tape (not supplied)

or a clamp (not supplied) to make the connection secure

and air tight.

Insert the duct connector back to the fan housing (A) follow

the guide slot from left to right. And it will be in place with

a “click” sound. Please secure it tightly.

7Install the flex bracket



Put the flex bracket (G) inside the ceiling through hole.

Fix the flex bracket (G) onto the joists with 4 screws (D).

The flex bracket is adjustable to fit different space

(12~22inches) between the joists.

Please make sure the bottom of the flex bracket will be

flush with the bottom of the joists.

9Install the fan housing on bracket



Align the 4 tabs (AA) on the fan housing through the

slots on the flex bracket (G). Then insert the tabs

through the slots until the fan housing (A) sitting on

the flex bracket (G).

Then bend the tabs (AA) to both sides to attach the

fan housing firmly on the flex bracket (G).

 Important: Cover and seal up all gaps with duct tape

NOTE: That it is common practice in heating and ventilation

systems using sheet metal ductwork and ﬁttings or ﬂexible duct

work tubing to use duct tape or aluminum tape to ensure air

tight seals and improve efﬁciency. Duct tape Duct tape Gaps

Installation - Existing Construction(continued)

Light Mode Operation

Compatibility

FOR USE WITH DIMMER MODELS:

LUTRON:P-PKG1W-WH-R,STCL-153PH-WH,CTCL-153PDH-WH,DVCL-153PR-WH,MACL-153MLH-WH,TGCL-153PH-WH,MACL-LFQ-WH

LEVITON:R68-06674-P0T,R62-6674-P0W,C22-6672-1LW,R00-RNL06-TW,R11-DSL06-1TW,66DF-10W

TP-LINK:HS220

LEGRAND:RHCL453PNICCV4

For a complete list of compatible dimmers, please visit Homedepot.com

10 Select the light color

 Select desired LED color temperature by sliding the toggle

switch on the back of the grille (B).

5000K

4000K

3000K

5000K

4000K

3000K

11 Install the grille with light



Attach the grille by squeezing one spring together and inserting

the springs into the spring guides in the fan housing (A) firstly.

Connect LED wire to the plug in the fan housing.

Then insert another spring and push the grille (B) up against

the ceiling.

Check that the installation is secure and safe from falling objects.

Plug



To change to night light mode while using the main light, switch

the wall switch off then back on again within 2 seconds.

To change to main light mode while using night light mode,

switch the wall switch off then back on again within 2 seconds.

NOTE:  If you connect the light and fan on two

separate switches, light and fan will operate

independently. If you connect the light and fan on one

switch, the light and fan will operate as the same time,

preventing the night light from being on without the fan.

 Do not connect the fan to a dimmer.

HAMPTONBAY.COM

Please contact 1-800-841-1350 for further assistance.

WARNING: Disconnect power supply before servicing.

 See SAFETY INFORMATION before proceeding. Routine maintenance should be done at least once a year.

 Never use solvents, thinner or harsh chemicals for cleaning the fan.

 Do not allow water to enter the motor.

 Do not immerse metal parts in water.

Care and Maintenance

Troubleshooting

Problem Possible Cause Solution

The fan seems louder than

it should.

The CFM is too great. Be sure the CFM rating on the fan matches the square

footage of your room.

The damper is damaged or not working properly.

Check the damper to ensure it is opening and closing

properly. If the damper has become damaged, please call

Customer Service.

The bend in the duct is too close to the fan discharge. Be sure you do not have any sharp bends in the duct closer

than 18 in. to the fan discharge.

Use the recommended size ducting to reduce fan noise.

The fan body is not attached securely. Be sure the fan is securely attached to the ceiling joists.

The fan is not clearing the

room.

Be sure a door or window is slightly ajar or opened to allow

Be sure the CFM rating on the fan matches the requirements

for your room size.

NOTE: Using a tissue is not the correct method for

determining if the fan is operating properly. If the fan

clears steam from the room within approximately 15

minutes of completing your shower, then the fan is

operating properly.

Questions, problems, missing parts? Before returning to the store,

call Hampton Bay Customer Service

8 a.m. - 7 p.m., EST, Monday-Friday,

9 a.m. - 6 p.m., EST, Saturday

1-800-841-1350

HAMPTONBAY.COM

Retain this manual for future use.

4021V1.0

FCC compliance information is listed as below:

Responsible party: Leedarson America, Inc.

Responsible party address: 300 Technology

Court SE Suite 100, Smyrna, GA 30082

Telephone number: (678) 293-8382

GUÍA DE USO Y CUIDADO

VENTILADOR CON LED DE COLOR CAMBIANTE

Elemento #317297138/317297139

Modelos #LDS-BF3002/LDS-BF3003

¿Preguntas, problemas, piezas que faltan? Antes de volver a la tienda,

llame al servicio de atención al cliente de Hampton Bay

8 a.m. - 7 p.m., EST, Lunes-Viernes, 9 a.m. - 6 p.m., EST, Sábado

1-800-841-1350

HAMPTONBAY.COM

¡GRACIAS!

Agradecemos la conanza que tiene en Hampton Bay al comprar este ventilador de baño. Nos esforzamos por crear continuamente

productos de calidad diseñados para mejorar su hogar. Visítenos en línea para ver nuestra línea completa de productos disponibles

para mejorar su hogar.

¡Gracias por elegir Hampton Bay!

Índice de contenidos

Información de seguridad

Lea y comprenda todo este manual antes de intentar ensamblar, operar o instalar el producto.

Índice de contenidos ..................................................... 2

Información de seguridad

Especificaciones del producto

............................................. 2

..................................... 4

Instalación típica .......................................................... 4

Diagrama de cableado .................................................. 4

Garantía .......................................................................... 5

GARANTÍA LIMITADA DE POR VIDA ........................................ 5

CUÁL ES LA COBERTURA ....................................................... 5

Preinstalación ................................................................ 5

PLANIFICACIÓN DE LA INSTALACIÓN ..................................... 5

HERRAMIENTAS NECESARIAS ..................................................5

CONTENIDO DEL PAQUETE ......................................................6

Instalación - Construcción nueva con soporte flexible 7

Instalación - Construcción existente ......................... 11

Funcionamiento del modo de luz ............................... 13

Compatibilidad ............................................................. 13

Instalación - Construcción nueva sin soporte flexible 9

Cuidado y mantenimiento ........................................... 14

Solución de problemas ............................................... 14

1. Desconecte siempre la fuente de alimentación antes de reparar el ventilador, el motor o la caja de conexiones.

2. Siga todos los códigos locales de construcción, seguridad y electricidad, así como el NEC (Código Eléctrico Nacional) y la OSHA (Ley de Seguridad

y Salud Ocupacional).

3. El suministro del servicio eléctrico debe ser de 120 Volts, 60 hertz.

4. Este producto debe conectarse correctamente al conductor de tierra del circuito de alimentación.

5. No doble ni tuerza los cables de alimentación.

6. No utilice este ventilador con ningún dispositivo de control de estado sólido, como un mando a distancia, un atenuador o determinados

temporizadores. Los temporizadores mecánicos no son dispositivos de estado sólido.

7. No lo instale en un techo con un aislamiento superior a R50.

8. Los ductos deben ser instalados en línea recta con mínimas curvas.

9. El tamaño de los ductos debe ser el mismo que el de descarga y no debe ser reducido. La reducción del tamaño del ducto puede aumentar el

ruido del ventilador.

10. Para garantizar el rendimiento, utilice los atenuadores recomendados en la lista si es necesario.

ADVERTENCIA: Para reducir el riesgo de incendio, descarga eléctrica o lesiones a las personas,

1. Utilice esta unidad de la manera prevista por el fabricante. Si tiene alguna duda. Llame al servicio de atención al cliente.

2. Antes de realizar el mantenimiento o la limpieza de la unidad, desconecte la alimentación en el panel de servicio y bloquee los medios de

desconexión de servicio para evitar que la alimentación se conecte accidentalmente. Cuando no se pueda bloquear el medio de desconexión del

servicio, ﬁje de forma segura un dispositivo de advertencia prominente, como una etiqueta, en el panel de servicio.

3. El trabajo de instalación y el cableado eléctrico deben ser realizados por una persona cualiﬁcada, de acuerdo con todos los códigos y normas

aplicables, incluyendo los de construcción contra incendios.

4. Se necesita suﬁciente aire para una combustión adecuada y para la evacuación de los gases a través del conducto de humos (chimenea) de los

equipos de combustión para evitar el reﬂujo. Siga las directrices del fabricante del equipo de calefacción y las normas de seguridad, como las

publicadas por la Asociación Nacional de Protección contra Incendios (NFPA), y la Sociedad Americana de Ingenieros de Calefacción,

Refrigeración y Aire Acondicionado (ASHRAE) y las autoridades locales de códigos.

5. Al cortar o perforar la pared o el techo, evite dañar el cableado eléctrico y otros elementos ocultos.

6. Los ventiladores con ductos siempre deben tener ventilación hacia el exterior.

7. Si esta unidad se instala sobre una bañera o una ducha, debe tener la designación de ser apropiada para dicho uso y estar conectada a un

circuito derivado con protección GFCI (Ground Fault Circuit Interrupter).

8. SÓLO PARA USO EN VIVIENDAS UNIFAMILIARES Y BIFAMILIARES.

9. TIPO IC-PROTEGIDO INTRÍNSECAMENTE

10. SÓLO PARA USO EN INSTALACIONES NO RESISTENTES AL FUEGO.

11. APTO PARA LUGARES HÚMEDOS

PRECAUCIÓN: Sólo para uso general de ventilación. No utilizar para extraer materiales y vapores peligrosos o explosivos.

PRECAUCIÓN: No utilizar en zonas de cocina.

Para reducir el riesgo de lesiones a las personas, instale el ventilador a una altura mínima de 2.1 m sobre el suelo.

PRECAUCIÓN:

tenga en cuenta lo siguiente:

HAMPTONBAY.COM

Please contact 1-800-841-1350 for further assistance.

Información de seguridad

Número de modelo: LDS-BF3002,LDS-BF3003

Nombre comercial: HAMPTON BAY

Responsable: 300 Technology Court SE Suite 100, Smyrna, GA 30082

Tel. : (678) 293-8382

Laboratorio de pruebas: Intertek Testing Services Shanghai

Building No.86, 1198 Qinzhou Road (North), Caohejing Development Zone, Shanghai 200233, China

Este dispositivo cumple con el apartado 15 de la normativa de la FCC. Su funcionamiento está sujeto a las dos condiciones siguientes: (1) Este

dispositivo no puede provocar interferencias dañinas, y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluidas las que

puedan causar un funcionamiento no deseado.

NOTA: Este equipo ha probado y se ha observado que cumple con los límites de los dispositivos digital es de Clase B, de acuerdo con el apartado

15 de la normativa de la FCC.

Estos límites están diseñados para proporcionar una protección razonable contra interferencias perjudiciales en instalaciones residenciales. Este

equipo genera, utiliza y puede irradiar energía de radiofrecuencia y si no se instala y utiliza de acuerdo con las instrucciones suministradas,

podría causar interferencias perjudiciales para las comunicaciones por radio. No obstante, no se garantiza que no puedan producirse interferen-

cias en una instalación en particular. Si este equipo causa interferencias perjudiciales en la recepción de la señal de radio o televisión, lo cual

puede determinarse apagando y encendiendo el equipo, se recomienda al usuario que intente corregirlas realizando una o varias de las siguien-

tes acciones:

- Cambie la orientación o la ubicación de la antena receptora.

- Aumente la distancia entre el equipo y el receptor.

- Conecte el equipo a la toma de corriente en un circuito diferente al que está conectado el receptor.

- Consulte con el fabricante o con un técnico de radio y TV con experiencia para obtener ayuda.

Declaración de conformidad del proveedor del apartado 15 de la normativa de la FCC.

Instalación típica

Diagrama de cableado

ESPECIFICACIONES ESPECIFICACIONES

Consumo de energía: Ventilador 38W, Luz 20W

Voltaje: 120 V, 60 Hz

Flujo de aire: 160 CFM Luz principal: 1500 lm Luz nocturna: 2200K

Peso: 13.45 lbs.

Diámetro del ducto: 6 in. Requisitos de las dimensiones de la abertura del techo:

12.17 in. (L) x 11 in. (W).

Salida de sonido: 1.1 Sones

La instalación de ductos desde este ventilador hacia

el exterior del ediﬁcio tiene un fuerte efecto en el

ﬂujo de aire, el ruido y el uso de energía del

ventilador. Utilice el recorrido de ductos más corto y

recto posible para obtener el mejor rendimiento, y

evite instalar el ventilador con ductos más pequeños

que los recomendados. El aislamiento alrededor de

los ductos puede reducir la pérdida de energía e

inhibir el crecimiento de moho. Los ventiladores

instalados con ductos existentes pueden no

alcanzar su ﬂujo de aire nominal.

ADVERTENCIA: El cableado debe cumplir con todos los códigos

eléctricos aplicables. Desconecte la alimentación antes de retirar o

instalar los conectores

ADVERTENCIA: COBRE A COBRE SOLAMENTE. No utilice cables

Tapa del techo

(con compuerta

incorporada)

Acabado de

calafateo al

ducto

Tapón de

pared (con

compuerta

incorporada)

Aislar adecuadamente

alrededor del ventilador

para minimizar

la pérdida y ganancia

de calor del edicio

Carcasa del ventilador

Selle cualquier

hueco alrededor

de la carcasa del

ventilador

Tramo recto de

2 a 3 pies antes del codo

Un trozo corto de

ducto exible ayuda

a la alineación y

absorbe el sonido

ventilador

interruptor del ventilador

(se compra por separado)

interruptor de la luz

(se compra por separado)

Línea de 120Vtierra

negro

blanco

ground

luzventilador

negro

La luz LED se

puede conectar

a un interruptor

atenuador

Los cables del

ventilador no

se pueden

conectar a un

interruptor

atenuador

Especificaciones del producto

de aluminio.

HAMPTONBAY.COM

Please contact 1-800-841-1350 for further assistance.

GARANTÍA LIMITADA DE POR VIDA

CUÁL ES LA COBERTURA

Póngase en contacto con el equipo de atención al cliente en el 1-800-841-1350 o visite www.HAMPTONBAY.com.

Garantía

Preinstalación

PLANIFICACIÓN DE LA INSTALACIÓN

Antes de comenzar a ensamblar el producto, asegúrese de que dispone de todas las piezas. Compare las piezas con la lista de contenido del

paquete y el contenido del hardware. Si alguna pieza falta o está dañada, no intente ensamblar el producto.

ADVERTENCIA: Desconecte la electricidad en el cuadro de

fusibles antes de comenzar la instalación.

Saque con cuidado la unidad de la caja de cartón.

Compruebe el área por encima de la ubicación de la instalación para asegurarse de que el cableado se puede llevar a la ubicación prevista y que los

conductos se pueden llevar a cabo y el área tiene suﬁciente espacio para una ventilación adecuada.

Inspeccione los ductos y el cableado antes de proceder a la instalación.

Antes de la instalación, deje un acceso de inspección y mantenimiento futuro en un lugar que no interﬁera con el trabajo de instalación.

NOTA: La instalación puede variar dependiendo de cómo se haya

instalado el ventilador de baño anterior. No se incluyen todos los

suministros necesarios para la instalación de su ventilador de baño.

Sin embargo, la mayoría están disponibles en su tienda local de

mejoras domésticas o ferretería.

HERRAMIENTAS NECESARIAS (no incluidas)

Martillo

de uña

Brocas Destornillador

plano

Cinta

americana

Alicates

Destornillador

de estrella

Cuchillo de

trabajo

Taladro

eléctrico

Gafas Guantes

Si este producto falla debido a un defecto en los materiales o en la mano de obra en cualquier momento durante los primeros 3 años después de su

adquisición, el fabricante lo sustituirá gratuitamente, con gastos de envío a criterio del fabricante. Esta garantía no cubre los productos que hayan sido

maltratados, alterados, dañados, mal utilizados, cortados o desgastados. Esta garantía no cubre el uso en aplicaciones comerciales. Para reparar este

ventilador, utilice únicamente piezas de repuesto originales suministradas por el fabricante. El uso de piezas no originales para la reparación anulará la

garantía. El fabricante RECHAZA todas las demás garantías implícitas o expresas, incluidas todas las garantías de comerciabilidad y/o idoneidad para un

ﬁn determinado. Como algunos estados no permiten exclusiones o limitaciones de una garantía implícita, las exclusiones y limitaciones anteriores

pueden no ser aplicables. Esta garantía le otorga derechos legales especíﬁcos, y puede tener otros derechos que varían de un estado a otro.

Esta garantía se limita a la sustitución de las piezas defectuosas únicamente. Quedan excluidos los gastos de mano de obra y/o los daños que se

produzcan durante la instalación, la reparación o la sustitución, así como los daños incidentales y consecuentes relacionados con lo anterior. Cualquier

daño a este producto como resultado de negligencia, mal uso, accidente, instalación incorrecta o uso distinto al previsto ANULARÁ ESTA GARANTÍA. Los

gastos de envío para la devolución del producto como parte de una reclamación de la garantía deben ser pagados por el cliente.

La page charge ...