ATEN CL1000M Manuel utilisateur

SlideawayTM LCD Console

CL1000

User Manual

www.aten.com

CL1000 User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

CE Warning: This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may be required

to take adequate measures.

KCC Statement

유선 제품용 / A 급 기기 ( 업무용 방송 통신 기기 )

이 기기는 업무용 (A 급) 전자파적합기기로서 판매자 또는 사용자는 이

점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적으로

합니다 .

RoHS

This product is RoHS compliant.

CL1000 User Manual

iii

SJ/T 11364-2006

The following contains information that relates to China.

CL1000 User Manual

iv

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

International http://eservice.aten.com

International 886-2-8692-6959

China 86-10-5255-0110

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

United Kingdom 44-8-4481-58923

CL1000 User Manual

v

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

A typical LCD (Liquid Crystal Display) monitor has millions of pixels. A dead

pixel refers to a pixel with a defect in its ability to display the correct color

output. It most often looks like a tiny black or white spot on your screen,

although it can be any other color. Since even a tiny dust particle on one of the

pixels during the manufacturing process or a slight bump during shipping can

create a dead pixel, the ISO 13406-2 norm defines 4 classes of acceptable

screens with dead pixels--Class 1 is the best; Class 4 is the worst. Almost all

manufacturers use Class 2 to establish their warranties, which allows a certain

amount of dead pixels to exist before they will replace the screen. Since the

manufacturers consider these screens to be acceptable under ISO

specifications, we cannot be responsible for replacement or warranty of the

TFT LCD panel.

CL1000 User Manual

vi

Package Contents

Basic Package

The basic CL1000 package consists of:

1 CL1000 with Standard Rack Mount Kit

1 Custom KVM Cable Set

1Power Cord

1 User Manual*

1 Quick Start Guide

Optional Equipment

Depending on any optional equipment that you may have purchased, one of the

following may be included in your package:

Standard Rack Mount Kit - Long

Easy-Installation Rack Mount Kit - Short

Easy-Installation Rack Mount Kit - Long

Check to make sure that all the components are present and that nothing got

damaged in shipping. If you encounter a problem, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit, and/or any of the

devices connected to it.

*Features may have been added to the CL1000 since this manual was printed.

Please visit our website to download the most up-to-date version of the

manual.

Manual Part No. PAPE-0287-102G

Manual Date: 2015-08-19

All other brand names and trademarks are the registered property of their respective owners.

CL1000 User Manual

vii

Contents

EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Basic Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Optional Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Chapter 1.

Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Switches and Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2.

Hardware Setup

Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Standard Rack Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 3.

Operation

Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

LCD OSD Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

LCD Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Adjustment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Manufacturing Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Port ID Numbering & Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

CL1000 User Manual

viii

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Optional Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

About SPHD Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

CL1000 User Manual

ix

About this Manual

This User Manual is provided to help you get the most from your CL1000

system. It covers all aspects of installation, configuration and operation. An

overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the CL1000 system. Its

purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Hardware Setup, provides step-by-step instructions for setting

up your installation, and explains some basic operation procedures.

Chapter 3, Operation, explains the fundamental concepts involved in

operating the CL1000.

An Appendix, provides specifications and other technical information

regarding the CL1000.

CL1000 User Manual

x

Conventions

This manual uses the following conventions:

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦Bullet lists provide information, but do not involve sequential steps.

→Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start → Run means to

open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

1

Chapter 1

Introduction

Overview

The CL1000 is a KVM console module that feature an integrated LCD panel,

full keyboard and touchpad in a 1U rack-mountable sliding housing. It was

developed in response to the enormous popularity of the sliding console found

on the CL1008 and CL1016 KVM switches. Those switches are made up of

two major modules: the front-end sliding KVM Console module, and the back-

end KVM Switch module.

The CL1000 is similar to the front-end Console module found on the CL1008

and CL1016. Its purpose is to serve as the front end sliding console for

compatible KVM switches.1 By only having to purchase the CL1000, users

who already have a compatible KVM switch can take advantage of the space

saving and efficiency benefits of the sliding console module without the

unnecessary expense of having to purchase a model that includes a KVM

switch module.

Setup is fast and easy. Simply use the KVM cable set supplied with this

package to link the CL1000's KVM port to the console port of your KVM

switch and you are ready to go.

1. The CL1000 supports most KVM switches that have PS/2 console port connectors. If

you are unsure if your switch is supported, check with your dealer.

CL1000 User Manual

2

Features

Exclusive LED illumination light - designed by ATEN to illuminate the

keyboard and touchpad to allow visibility in low-light conditions

Integrated KVM console with a 17" LED-backlit LCD monitor in a sliding

housing with top and bottom clearance for smooth operation in a 1U high

system rack

LCD module rotates up to 115o for a more comfortable viewing angle

Standard rack mount kit included – optional Easy Rack Mounting (single

person installation) rack mount kit available (requires separate purchase)

Compatible with most PS/2 KVM switches

Internal power supply

High video resolution:

Up to 1280 x 1024 @75Hz

Supports DDC, DDC2, DDC2B

DDC emulation of the LCD monitor

Video settings of attached computers are automatically adjusted for

optimal output to the LCD monitor

Keyboard language support: English (UK), English (US), French,

German, German (Swiss), Greek, Hungarian, Italian, Japanese, Korean,

Russian, Spanish, Swedish, Traditional Chinese

Chapter 1. Introduction

3

Requirements

Switches and Computers

The CL1000 supports most KVM switches that have PS/2 console port

connectors. If you are unsure whether your switch is supported or not,

check with your dealer.

The integrated LCD monitor's maximum resolution is 1280 x 1024 @

75 Hz. Make sure that none of the resolution settings of the connected

computers exceed the LCD monitor's maximum resolution.

Cables

For optimum signal integrity and to simplify the layout, we strongly

recommend that you use the high quality custom cable set provided with this

package. Different length cable sets, described in the table below, can be

purchased from your dealer.

Operating Systems

Supported operating systems are shown in the table, below:

*This operating system does not support USB.

Length (m) Part Number

1.2 2L-5201P

1.8 2L-5202P

3.0 2L-5203P

6.0 2L-5206P

OS Version

Windows 2000 and higher

Linux RedHat 7.1–7.3, 8.0, 9.0, Fedora Core 2–4

SuSE 8.2, 9.3, 10

Mandriva (Mandrake) 9, 2005 Limited Edition, 2006

UNIX AIX 4.3, 5L

FreeBSD 4.2, 4.5

Novell Netware 5.0*, 6.0

CL1000 User Manual

4

Components

Front View

No. Component Description

1 Handle Pull to slide the KVM module out; push to slide the module in.

2 Slide Release In order to slide the console out, you must first release it by

moving this tab sideways. See page 11 for details on sliding

the console in and out.

3 LCD Display After sliding the KVM module out, flip up the cover to access

the LCD monitor.

4 LCD Controls The LCD On/Off switch is located here, as well as buttons to

control the position and picture settings of the LCD display.

See page 14, for details.

5 Keyboard

6 Touchpad

7 Power LED Lights dark green to indicate that the unit is receiving power.

8 Rack Mounting

Brackets

The rack mounting brackets located at each corner of the unit

secure the chassis to a system rack.

9 Lock LEDs The Num Lock, Caps Lock, Scroll Lock LEDs are located

here.

10 Reset Switch Located to the right of the Lock LEDs. Press this recessed

switch in with a thin object to perform a system reset.

11 LED Illumination

Light

Press the Exit/Light pushbutton for two seconds to turn the

LED light On or Off. (Default: On)

Chapter 1. Introduction

5

Rear View

No. Component Description

1 Power Socket This is a standard 3-prong AC power socket. The power cord

from your AC source plugs in here.

2 Power Switch This is a standard rocker switch that powers the unit On and

Off.

3 KVM Port The cable that links the CL1000 to the KVM switch plugs in

here.

Note: The shape of this SPHD connector has been

specifically modified so that only KVM cables designed to

work with this switch can plug in (see Cables, page 3, for

details).

1 2 3

CL1000 User Manual

6

This Page Intentionally Left Blank

7

Chapter 2

Hardware Setup

Before you Begin

Standard Rack Mounting

A standard rack mount kit is provided with your CL1000. The kit enables the

console to be mounted in rack with a depth of 42–72 cm.

Note: 1. It takes two people to mount the console: one to hold it in place, the

other to screw it in.

2. The standard rack mounting kit does not include screws or cage nuts.

If you need additional screws or cage nuts, contact your rack dealer.

3. Optional mounting kits, including single person Easy Installation

kits, are available with a separate purchase. See page 26 for optional

rack mounting details.

1. Important safety information regarding the placement of this

device is provided on page 17. Please review it before proceeding.

2. Make sure that power to all the devices you will be connecting up

have been turned off. You must unplug the power cords of any

computers that have the Keyboard Power On function.

L Brackets

Side Mountng

Brackets

CL1000 User Manual

8

To rack mount the console, do the following:

1. While one person positions the CL1000 in the rack and holds it in place,

the second person loosely screws the front brackets to the rack.

2. While the first person still holds the CL1000 in place, the second person

slides the L brackets into the CL1000's side mounting brackets from the

rear until the bracket flanges contact the rack, then screws the L brackets

to the rack.

3. After the L brackets have been secured, tighten the front bracket screws.

Note: Allow at least 5.1 cm on each side for proper ventilation, and at least

12.7 cm at the back for the power cord and cable clearance.

Chapter 2. Hardware Setup

9

Installation

Refer to the installation diagram as you perform the installation steps. The

numbers in the diagrams correspond to the numbers of the steps.

1. Plug the SPHD connector end of the KVM cable provided with this unit

into the CL1000's KVM port.

2. Plug the keyboard, monitor, and mouse connectors of the KVM cable into

their respective ports on the Console Section of the KVM switch.

3. Plug the power cord into the CL1000's power socket and into an AC power

source.

4. Power up your KVM installation.

5. Turn on the power to CL1000.

3

2

4

5

1

CL1000 User Manual

10

This Page Intentionally Left Blank

La page charge ...

ATEN CL1000M Manuel utilisateur

Ce manuel convient également à

ATEN CL1000M Manuel utilisateur

dans d''autres langues

Documents connexes