ATEN CL5708N-ATA-AU Technical Manual

LCD KVM Switch

CL5708 / CL5716

User Manual

www.aten.com

CL5708 / CL5716 User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at their own expense.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate this equipment.

Warning:

Operation of this equipment in a residential environment could cause radio

interference.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

KCC Statement

RoHS

This product is RoHS compliant.

CL5708 / CL5716 User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

CL5708 / CL5716 User Manual

iv

Package Contents

Basic Package

The basic CL5708 / CL5716 package consists of:

 1 CL5708 / CL5716 KVMP Switch with standard Rack Mounting Kit

 2 Custom KVM Cable Sets

 1 5-in-1 USB / PS/2 Console Cable

 1 Firmware Upgrade Cable

 1 Power Cord (AC Power Models)

 1 User Instructions*

Optional Equipment

Depending on any optional equipment that you may have purchased, one of the

following may be included in your package:

 Standard Rack Mounting Kit - Long

 Easy-Installation Rack Mounting Kit - Short

 Easy-Installation Rack Mounting Kit - Long

 Fingerprint Identification Module

Check to make sure that all the components are present and that nothing got

damaged in shipping. If you encounter a problem, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit, and/or any of the

devices connected to it.

* Features may have been added to the CL5708 / CL5716 since this manual

was published. Please visit our website to download the most up-to-date

version of the manual.

Manual Date: 2019-05-03

All other brand names and trademarks are the registered property of their respective owners.

CL5708 / CL5716 User Manual

v

Contents

EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Basic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Optional Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

1. Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

External Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Rear View (AC Power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2. Hardware Setup

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Before you Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Standard Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Single Level Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

AC Power Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Cabling Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Daisy Chain Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3. Basic Operation

Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

LCD OSD Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

The LCD Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

CL5708 / CL5716 User Manual

vi

LCD Adjustment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Changing Station Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Hot Plugging External Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . 25

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Manual Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

USB Peripheral Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4. OSD Operation

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Manufacturing Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

OSD Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

OSD Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

OSD Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

OSD Main Screen Headings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

F2: LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

F3: SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

F5: SKP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

F6: BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

F8: LOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5. Keyboard Port Operation

Hotkey Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Invoke Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Number Lock and Minus Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Control and F12 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Select the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Auto Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Invoking Auto Scan: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Computer Keyboard / Mouse Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Quick Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

OSD Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Port OS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Set USB Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Restore Default Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Hotkey Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

CL5708 / CL5716 User Manual

vii

6. Keyboard Emulation

Mac Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Sun Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

7. The Firmware Upgrade Utility

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . .55

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

CL5708 to Compatible 8-Port Switches . . . . . . . . . . . . . . . . . . . . . . . 72

CL5708 to Compatible 16-Port Switches . . . . . . . . . . . . . . . . . . . . . .72

CL5716 to Compatible 8-Port Switches . . . . . . . . . . . . . . . . . . . . . . .73

CL5716 to Compatible 16-Port Switches . . . . . . . . . . . . . . . . . . . . . .73

Supported KVM Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Clear Login Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

OSD Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Optional Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Standard - Long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Easy Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Keyboard Invocation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

About SPHD Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

CL5708 / CL5716 User Manual

viii

About this Manual

This user manual is provided to help you get the most from your CL5708 /

CL5716 system. It covers all aspects of installation, configuration and operation.

An overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the CL5708 / CL5716 system.

Its purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Hardware Setup, describes how to set up your installation. The

necessary steps from a basic single stage hookup to a complete 32-switch daisy

chained operation are provided.

Chapter 3, Basic Operation, explains the fundamental concepts involved

in operating the CL5708 / CL5716.

Chapter 4, OSD Operation, provides a complete description of the

CL5708 / CL5716's on-screen display (OSD), and how to work with it.

Chapter 5, Keyboard Port Operation, details all of the concepts and

procedures involved in the hotkey operation of your CL5708 / CL5716

installation.

Chapter 6, Keyboard Emulation, provides tables that list the PC to Mac

and PC to Sun keyboard emulation mappings.

Chapter 7, The Firmware Upgrade Utility, explains how to use this

utility to upgrade the CL5708 / CL5716's firmware with the latest available

versions.

An Appendix, provides specifications and other technical information

regarding the CL5708 / CL5716.

CL5708 / CL5716 User Manual

ix

Conventions

This manual uses the following conventions:

Product Information

For information about all ALTUSEN products and how they can help you

connect without limits, visit ALTUSEN on the Web or contact an ALTUSEN

Authorized Reseller. Visit ALTUSEN on the Web for a list of locations and

telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means

to press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential

steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→

Run means

to open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

CL5708 / CL5716 User Manual

x

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

The CL5708 / CL5716 Slideaway

TM

LCD KVMP Switch is an integrated LCD

console and keyboard, video, and mouse (KVM) switch that offers secure

access to 8 or 16 attached computers and mounts in only 1U of rack space. It

features an independently retractable 17” LED-backlit LCD monitor and

keyboard with built-in touchpad. An extra console port is provided on the rear

panel to manage the LCD KVM switch from an external console (monitor,

keyboard, and mouse) up to 20 meters away. For added convenience it also

supports an external USB mouse.

The CL5708 / CL5716 supports both PS/2 and USB keyboards and mice for

the connected computers, and the CL5708 / CL5716 supports USB peripheral

devices to be used with the attached computers. A single CL5708 / CL5716 can

control up to 8 or 16 computers. As many as 31 additional compatible KVM

switches can be daisy chained together, so that up to 256 or 512 computers can

all be controlled from a single keyboard, monitor, and mouse console. (See the

Appendix for a list of compatible ATEN switches.)

The CL5708 / CL5716 is built on a modular design. The KVM section can be

detached from the switch section for convenient maintenance and repair.

There are four models in the series as outlined in the following table:

Your CL5708 / CL5716 investment is protected by an included firmware

upgrade utility. You can stay current with the latest functionality

improvements by downloading firmware update files from our website as they

become available, and using the utility to quickly and conveniently perform the

upgrade.

Setup is fast and easy: plugging cables into their appropriate ports is all that is

entailed. Because the CL5708 / CL5716 intercepts keyboard input directly,

Model LCD Panel KVM Ports

CL5708M 17" 8

CL5716M 17" 16

CL5708N 19” 8

CL5716N 19” 16

CL5708 / CL5716 User Manual

2

there is no software to configure, no need to get involved in complex

installation routines, nor any need to be concerned with incompatibility

problems. Access to any computer connected to the installation is easily

accomplished either by entering hotkey combinations from the keyboard, or by

means of a powerful, mouse driven, OSD (on-screen display) menu system. A

convenient Auto Scan feature also permits automatic scanning and monitoring

of the activities of all computers running on the installation one by one.

There is no better way to save time and money than with a CL5708 / CL5716

installation. By using the CL5708 / CL5716 with its sliding LCD console to

manage your installation, you: eliminate the expense of having to purchase a

separate keyboard, monitor, and mouse for each computer; save all the space

those extra components would take up; save the space that a keyboard, monitor,

and mouse would take with a standard KVM switch; save on energy costs; and

eliminate the inconvenience and wasted effort involved in constantly moving

from one computer to another.

Chapter 1. Introduction

3

Features

 Exclusive LED illumination light - designed by ATEN to illuminate the

keyboard and touchpad to allow visibility in low-light conditions

 Integrated KVM console with 17” or 19” LED-backlit LCD in a

Slideaway

TM

housing

 Space saving technology – up to two consoles (one bus) control up to 8 or

16 computers

 Daisy chain up to 31 additional units – control up to 256 (CL5708) or 512

(CL5716) computers from a single console

 Dual Interface – supports computers with PS/2 or USB keyboards and mice

 USB port allows each computer to access USB peripherals

1

 Multiplatform support – Windows 2000/XP/Vista, Linux, Mac, and Sun

 Supports multimedia USB keyboards for PC, Mac and Sun

 Auto PS/2 and USB interface detection

 Keyboard and mouse emulation (PS/2 and USB) for smooth switching and

simultaneous booting of multiple computers even when the console focus

is elsewhere

 Superior video quality – supports resolutions up to 1280 x 1024 @ 75 Hz

 No software required – convenient computer selection via mouse-driven,

intuitive OSD (on-screen display) menus and hotkeys

 Auto-senses station's position on daisy chained installations; no need for

manual dip switch setting; front panel led indicates station's position

 Port names automatically reconfigured when station sequence is changed

 Two level password security – authorized users view and control computers

 Supports one administrator and four user accounts with separate profiles

 Auto Scan mode enables continuous monitoring of user-selected computers

 Broadcast support – commands from the keyboard can be broadcast to all

available computers on the installation

 Hot pluggable – add or remove computers without having to power down

the switch

 Beeper on/off via hotkey and OSD

1. The USB peripheral function only works with USB cable set connections. It will not

work with PS/2 cable set connections.

CL5708 / CL5716 User Manual

4

 Firmware upgrades to all the chained KVM switches at the same time via

the daisy chain cable

 Extra console port – manage computers from an external console (monitor,

USB or PS/2 keyboard and mouse)

 Supports external USB mouse

 Conveniently located station and port selectors, each with two 7-segment

LED displays to quickly switch to target computers

 Dedicated Hotkey mode and OSD Invocation Keys reduce the number of

keystrokes and provide quick access to these functions

 OSD tree structure makes finding and managing computers easy

 Console lock – enables the console drawer to remain securely locked away

when not in use

 OSD port list automatically expands when new stations are added

 Security – Administrator/User password authorization for enhanced

security protection; Administrator access rights synchronized between

master and slave stations

 OSD screen automatically adjusts to resolution changes

 Two types of logout: manual and timed

 Slideaway

TM

housing is slightly less than 1U with top and bottom

clearance for smooth operation in 1U of rack space

 DDC emulation – video settings of each computer are automatically

adjusted for optimal output to the monitor

 Standard 105-key keyboard

 Keyboard status restored when switching computers

 Keyboard language supports English (US), English (UK), French,

German, German (Swiss), Greek, Hungarian, Italian, Japanese, Korean,

Russian, Spanish, Swedish and Traditional Chinese

Chapter 1. Introduction

5

Requirements

External Console

The following hardware components are required for the external console:

 A VGA, SVGA, or multisync monitor capable of displaying the highest

resolution provided by any computer in the installation.

 A USB or PS/2 keyboard and mouse

Computers

The following equipment must be installed on each computer:

 A VGA, SVGA, or multisync video graphics card with an HDB-15 port.

Note: The integrated LCD monitor's maximum resolution is

1280 x 1024 @ 75 Hz. Make sure that none of the computer

resolution settings exceed the LCD monitor's maximum resolution.

 PS/2 mouse and keyboard ports (6-pin Mini-DIN), or at least one USB port.

 Direct support Sun USB systems; or, for Sun legacy systems, an ATEN

CV130A Sun Console Converter.

Cables

Substandard cables may damage the connected devices or degrade overall

performance. For optimum signal integrity and to simplify the layout, we

strongly recommend that you use the high quality CS Custom Cable sets

described below:

Function Length Part Number

KVM switch to KVM switch

(Daisy chaining)

0.6 m

1.8 m

3 m

5 m

15 m

2L-1700

2L-1701

2L-1703

2L-1705

2L-1715

KVM switch to computer PS/2 1.2 m

1.8 m

3.0 m

6.0 m

1.8 m

2L-5201P

2L-5202P

2L-5203P

2L-5206P

2L-5702P

USB 1.2 m

1.8 m

3.0 m

5.0 m

2L-5201U

2L-5202U

2L-5203U

2L-5205U

CL5708 / CL5716 User Manual

6

Operating Systems

Supported operating systems are shown in the table, below:

OS Version

Windows 2000 and higher

Linux RedHat 7.1 and higher

SuSE 9.0 and higher

Mandriva (Mandrake) 9.0 and higher

UNIX AIX 4.3 and higher

FreeBSD 4.2 and higher

Sun Solaris 8 and higher

Novell Netware 5.0 and higher

Mac OS 9 and higher

DOS 6.22

Chapter 1. Introduction

7

Components

Front View

Note: The CL5716 is pictured in the diagrams of this chapter. However, the

CL5708 is the same as the CL5716, except that it has 8 KVM ports.

16

2

1

2

4

3

5

6

14

15

13

12

11

10

9

8

7

EXIT I LIGHT

17

CL5708 / CL5716 User Manual

8

No. Component Description

1 Handle Pull to slide the KVM module out; push to slide the module in

(see item 2 in this table).

2 Slide Release In order to slide the console out, you must first release it by

sliding these tabs to the inside. See page 19 for details on

sliding the console in and out.

3 LCD Display After sliding the KVM module out, flip up the cover to access

the LCD monitor.

4 LCD Controls The LCD On/Off switch is located here, as well as buttons to

control the position and picture settings of the LCD display.

See page 23 for details.

5 Port LEDs An ON LINE LED lights to indicate that the computer

attached to its corresponding port is up and running.

6 Keyboard Standard 105-key keyboard

7 Touchpad Standard mouse touchpad

8 Station/Port

Switches

Press the UP or DOWN buttons for the Port ID and Station ID

to bring the KVM focus to the computer attached to the

corresponding port. See Manual Port Switching, page 26.

9 External Mouse

Port

A USB mouse port is provided for users who prefer to use an

external mouse.

10 Power LED Lights to indicate that the unit is receiving power.

11 Rack Mounting

Brackets

The rack mount brackets located at each corner of the unit

secure the chassis to a system rack.

12 Lock LEDs Num Lock, Caps Lock, Scroll Lock LEDs are located here.

13 Reset Switch Located to the right of the Lock LEDs. Press this recessed

switch in with a small object to perform a system reset.

14 Firmware

Upgrade

Section



Firmware Upgrade Port: The Firmware Upgrade Cable

that transfers the firmware upgrade data from the adminis-

trator's computer to the CL5708 / CL5716 plugs into this

RJ-11 connector.



Firmware Upgrade Switch: During normal operation this

switch should be in the NORMAL position. (See The Firm-

ware Upgrade Utility, page 55 for firmware upgrading

details.)

15 USB Port The USB port is available to connect a USB 1.1 peripheral

device (flash drive, CD-ROM drive, etc.) to the switch.

16 LED Illumination

Light

Illuminates the keyboard and touchpad to allow visibility in

low-light conditions.

17 Exit/Light

Pushbutton

Press the Exit/Light pushbutton for two seconds to turn the

LED Illumination Light On or Off. (Default: On)

Chapter 1. Introduction

9

Rear View (AC Power)

No. Component Description

1 Power Socket This is a standard 3-prong AC power socket. The power cord

from an AC source plugs in here.

2 Power Switch This standard rocker switch powers the unit on and off.

3 Daisy Chain Port When daisy chaining units, the cable plugs in here.

4KVM Port

Section

The cables that link to the computers plug in here.

Note: The shape of these SPHD connectors has been

specifically modified so that only KVM cables designed to

work with this switch can plug in (see the Cables section on

page 5, for details). Do NOT attempt to use ordinary 15 pin

VGA connector cables to link these ports to the computers.

5 Grounding

Terminal

The grounding wire used to ground the switch attaches here.

6 External

Console Port

For flexibility and convenience, the CL5708 / CL5716

supports an independent, external, KVM console.

The external console keyboard, monitor, and mouse cables

plug in here.

12 34

56

CL5708 / CL5716 User Manual

10

This Page Intentionally Left Blank

La page charge ...

ATEN CL5708N-ATA-AU Technical Manual

Ce manuel convient également à

ATEN CL5708N-ATA-AU Technical Manual

dans d''autres langues

Documents connexes

Autres documents