KB310-SSRE
Recessed-Mounted
Baby Changing Station
Cambiador Plegable
Table à Langer
Babywickelstation
Important. Retain for future reference. Read carefully.
Importante. Guárdelo para futuras consultas. Leer atentamente.
Important. À conserver pour information. À lire attentivement.
Wichtig. Zur späteren bezugnahme aufbewahren. Bitte sorgfältig durchlesen.
Koala Kare Products
Installation & Operations Instructions
The KB310 Baby Changing Stations have been designed to meet the following applicable provisions of the
2010 ADA Standards (ADAS) and the 2009/2017 American National Standards Institute A117.1 Standards
(ANSI 2009/2017) and the 2012 Texas Accessibility Standard (TAS) when properly installed and maintained.
To comply with these accessibility requirements the unit must be installed in a compliant location and height
in accordance with the installation instructions.
You are responsible for the safe operation of this unit.
3
KB310-SSRE
Operations Instructions
Please Note
To assure proper installation, it is suggested that
a qualified person or carpenter install the Koala
Baby Changing Station. Koala Kare Products will
not be responsible if the station is not installed
properly. Koala Baby Changing Stations have
been tested to hold a substantial static load. The
unit must be attached to a permanent wall that is
capable of holding a substantial load. The maximum
recommended total weight for this baby changing
station is 50 lbs. Excessive weight may cause a
hazardous or unstable condition to exist.
Inspection Criteria
A properly maintained baby changing station:
• Opens and closes smoothly.
• Has a functioning strap and buckle. Strap is held
firmly in place when buckle is depressed over it.
• Oers parents liners through a fully stocked liner
dispenser. (Dispenser built into unit.)
• Provides a clean, convenient place for customers
to attend to their children.
Restraint System
Check strap by releasing the lever on the buckle and
pulling one end of the strap up through the bottom
of the buckle, depressing the lever when the strap is
tight. Give the strap a tug in the horizontal direction
away from the buckle, checking that the strap
remains in place beneath the buckle. To loosen the
strap, release the lever and pull the strap from the
bottom of the buckle.
ASTM F2285-04 (2016)
WARNING: Never leave child unattended.
WARNING: Avoid serious injury from falling or
sliding out. Always use restraint system.
WARNING: Designed for Infants Only. Age up
to 3.5 years and weighing less than 50 lb (22.7
kg). Keep one hand on the child at all times.
Parcels or accessory items, or both, placed on the
unit may cause the unit to become unstable.
Replacement Parts
For a list of replacement parts for this product,
(such as straps, shocks and labels) please visit
www.koalabear.com.
Replacement parts and additional liners can be
purchased from your local distributor or direct from
Koala at www.koalabear.com.
ADA Requirements
Additional information on how this product
complies with ADA requirements can be found
in the KB310 & KB311 Baby Changing Stations
Accessibility Compliance document on
www.koalabear.com.
4
KB310-SSRE
Installation Instructions
Tools Needed
Safety Gloves Wall Stud FinderDrill Measuring TapePencil Level
1/8" (3mm)
(regular & masonry)
drill bits
Phillips Head
Screwdriver
7/32" (6mm)
(regular & masonry)
drill bits
1/4" x 3"
Flat Head Wood Screws
Quantity: 6
8-32" x 5/16"
Flange Button Phillips Head Screws
Quantity: 4
Allen Wrench
Quantity: 1
9/32" x 7/8"
Flat Head Phillips Screws
Quantity: 3
Hardware Provided
Scan the QR code to view the installation video and
to find product resources. Also available at:
www.koalabear.com/product-catalog/kb310-ssre/
*Diagrams are not to scale.
5
KB310-SSRE
Installation Instructions
Step 1:
• Prepare the rough wall opening per the Technical
Data sheet. Fig. 1 For more information navigate to
www.koalabear.com.
• Be sure to wear safety gloves to protect your hands
from the products exposed metal edge.
Step 2:
• Remove the handles and bag hook from the
packaging and set to one side.
• Open the unit by pulling up on the handle mounting
studs and remove the plastic liner dispenser from
inside the unit and set to one side.
Step 3:
• With the assistance of a second person, lift and
position the unit into the rough wall opening.
• Have one person hold the unit and place into the
wall while the other opens the unit using the handle
mounting studs.
Step 4:
• Open unit fully and you will have access to the six
mounting holes on either side of the unit. Fig. 2
• Using the hardware provided, predrill and screw
through the mounting holes. Do not over tighten.
• Once secured, the unit will no longer need to be
held in place.
Step 5:
• With the unit open, take the liner dispenser and
position it over the exposed metal frame in the
center of the recess.
• Use the provided key to open the liner dispenser.
This will provide access to the four mounting holes.
• Use the provided hardware to secure the liner
dispenser to the metal frame. Fig. 3
• Lock the liner dispenser and close the unit.
Fig. 1
Fig. 2
Fig. 3
*Diagrams are not to scale.
6
KB310-SSRE
Installation Instructions
Step 6:
• Take one of the provided handles and position it
over the handle mounting studs, so that the open
portion is toward the top of the unit.
• Use provided Allen wrench to tighten the set screws
in the handles, securing it to the handle mounting
studs. Fig. 4
• Repeat for the opposite handle.
Step 7:
• Test the unit by opening and closing multiple times,
ensuring it opens and closes smoothly.
• Remove protective film from the surface of the unit.
Step 8:
• To install the bag hook, measure up 44" from
finished floor in the desired location and mark the
wall. Fig. 5
• Position the bag hook on the wall so that the top of
the mounting plate is level with the 44" mark.
• Position the bag hook over a wall stud for optimal
strength.
• Mark then predrill the mounting holes.
• Use the provided screws to secure the bag hook in
position, then take the escutcheon plate and screw
it over the mounting plate to cover the mounting
screws. Fig. 6
Fig. 4
Fig. 5
*Diagrams are not to scale.
Fig. 6
Koala Kare Products
A Division of Bobrick
6982 South Quentin Street, Centennial, CO 80112-3945
Main: 303.539.8300 | Toll Free: 888.733.3456 | Fax: 303.539.8399
Website: koalabear.com | Email: customerservice@koalabear.com
©2020 Koala Kare Products, Form No. ###. December 2020
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
- English: KoalaKare KB310-SSRE User manual
Autres documents
-
Koala Kare KB310-SSRE Mode d'emploi
-
Koala Kare 311-32-KIT Mode d'emploi
-
Koala Kare KB310-SSWM Mode d'emploi
-
Koala Kare 301-5-KIT Manuel utilisateur
-
-
-
-
Koala Kare KB311-SSWM Manuel utilisateur
-