Haier HATS9CBS6BPLWI Manuel utilisateur

ENGLISH INSTALLATION AND USER'S MANUAL

ITALIANO MANUALE D'INSTALLAZIONE E D'USO

FRANÇAIS NOTICE D'INSTALLATION ET D'UTILISATION

ESPAÑOL MANUAL DE USO E INSTALACIÓN

DEUTSCH EINBAU- UND BEDIENUNGSANLEITUNG

NEDERLANDS HANDLEIDING VOOR INSTALLATIE EN GEBRUIK

ČESTÍNA NÁVOD K INSTALACI A POUŽITÍ

SLOVENČINA NÁVOD NA INŠTALÁCIU A POUŽITIE

INSTALLATION AND USER’S MANUAL

02

04

05

06

13

CONTENT

INTRODUCTION

SAFETY PRECAUTION

ELECTRICA L INSTALLATION

SPECIFICATION

INSTALLATION (VENT OUTSIDE)

INSTALLATION (VENT INSIDE)

DESCRIPTION OF COMPONENTS

OPERATION

MAINTENANCE

TROBULESHOOTING

CONFORMITY WITH DIRECTIVES

ENVIRONMENTAL PROTECTION

17

20

21

22

1

INTRODUCTION

Thank you for choosing this cooker hood.

This instruction manual is designed to provide you with all required

instructions related to the installation, use and maintenance of the appliance.

In order to operate the unit correctly and safety, please read this instruction

manual carefully before installation and usage.

The cooker hood uses high quality materials, and is made with a streamlined

design. Equipped with large power electric motor and centrifugal fan, it also

provides strong suction power, low noise operation, non-stick grease filter and

easy assembly installation.

Hereby, Candy Hoover Group Srl declares that the radio equipment is in

compliance with Directive 2014/53/EU and with the relevant Statutory

internet address: www.candy-group.com

SAFETY PRECAUTION

Never let the children operate the machine.

The cooker hood is for home use only, not suitable for barbecue, roast

shop and other commercial purpose.

The cooker hood and its filter should be clean regularly in order to

keep in good working condition.

Clean the cooker hood according to the instruction manual and keep

the unit from danger of burning.

Forbid the direct baking from the gas cooker.

Please keep the kitchen room a good convection.

Before connecting this appliance check that the power supply cord is

not damaged. A damage supply cord must be replaced by qualified

service personnel only.

There shall be adequate ventilation of the room when the range hood

is used at the same time as appliances burning gas or other fuels;

The air must not be discharged into a flue that is use d for exhausting

fumes from appliances burning gas or other fuels;

Regulations concerning the discharge of air have to be fulfilled.

Requirements (for the UKCA market).

The full text of the declaration of conformity is available at the following

2

Electrical Shock Hazard

˜

Only plug this unit into a properly earthed outlet. If in doubt seek

advice from a suitably qualified engineer.

˜

Failure to follow these instructions can result in death, fire, or

electrical shock.

5IFTFTIBMMCFBEFRVBUFWFOUJMBUJPOPGUIFSPPNXIFOUIFSBOHF

IPPEJTVTFEBUUIFTBNF UJNFBTBQQMJBODFTCVSOJOHHBTPSPUIFS

GVFMTOPUBQQMJDBCMFUPBQQMJBODFTUIBUPOMZEJTDIBSHFUIFBJSCBDL

JOUPUIFSPPN

UIFEFUBJMTDPODFSOJOHUIFNFUIPEBOEGSFRVFODZPGDMFBOJOH

UIFSFJTBGJSFSJTLJGDMFBOJOHJTOPUDBSSJFEPVUJOBDDPSEBODFXJUIUIF

JOTUSVDUJPOT

EPOPUGMBNFVOEFSUIFSBOHFIPPE

$"65*0/"DDFTTJCMFQBSUTNBZCFDPNFIPUXIFOVTFEXJUI

DPPLJOHBQQMJBODFT

- Children should be supervised to ensure that they do not play with

the appliance.

- Do not flambé under the range hood.

The range hood is not intended to be installed over a hob having

more than four hob elements

The lamp used in this product is not suitable for use

in the lighting of a room.

The purpose of this lamp is to provide illumination for using the product.

3

Direct Connection

The appliance must be connected directly to the mains using an

omnipolar circuit breaker with a minimum opening of 3mm between

the contacts.

The installer must ensure that the correct electrical connection has

been made and that it complies with the wiring diagram.

The cable must not be bent or compressed.

Regularly check the power plug and power cord for damage. If the

supply cord is damaged, it must be replaced by a special cord or

assembly available from the manufacturer or its service agent.

WARNING: This is a Class I appliance and MUST be earthed

This appliance is supplied with a 3 core mains cable coloured as

follows:

Brown = L or Live

Blue = N or Neutral

Green and Yellow = E or Earth

The fuse must be rated at 3 Amps.

Electrical Installation

All installation must be carried out by a competent person or qualified

electrician. Before connecting the mains supply ensure that the mains

voltage corresponds to the voltage on the rating plate.

4

Standard Installation Accessories List

Spec. Qty

Casing 1

Upper Chimney 1

Lower Chimney 1

Lower chimney bracket 1

Upper chimney bracket 1

Hanging Board 1

φ8 rawl plugs

φ8×φ6 white color 9

Screws

ST4.0×30 9

φ7.2screws

ST4.0×8 2

Illustration Picture

Air outlet 1

Carbon ﬁlter 2

Plasma 1

5

INSTALLATION

˄

wall mounting

˅

If you have an outlet to the outside, your cooker hood can be connected as

below picture by means of an extraction duct (enamel, aluminum, flexible pipe

non flammabe with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should be placed at a distance of 65~75cm above

the cooking plane for best effect.

3. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten

the bracket onto the wall with the screws provided.

Wall plug

Wall bracket 107.5mm

Screw(4mm x 30mm)

6

4. Leave up the cooker hood and hang onto the wall bracket hook.

5. Fix the one-way-valve to the air outlet of the cooker hood. Then,

attached the exhaust pipe onto the one-way-valve as shown below.

Exhaust pipe

Cooker hood

7

6. i. Place the glass in appropriate position on the top the cooker

hood.

ii. Fix with 4 screws and washer. In order to avoid the glass

cracking, please do not tighten the screws too strongly.

i. By Put the inner chimney into outer chimney .Then pulling out

the inner chimney upwards. Adjust to reach the height required.

ii. Sliding the chimney to adjust the chimney height. When the

height you required is reached, then hang the fixing hole to the fixing

screws as showed in below pictures.

Inner chimney

Outer chimney

8

8. i. Drill 2 x 8mm holes to accommodate the plate II. Screw and

tighten the plate II onto the wall with 2 screws provided.

ii. Assembly the chimney onto the unit and fix it with 2 screws.

Plate II

Wall plug

Screw

4mm x 8mm

Screw

(4mm x 30mm)

9

StandardInstallationAccessoriesList

Spec. IllustrationPicture Qty

AirDeflector 1

Bracket 1

ĳ8rawlplugs

ĳ8×ĳ6whitecolor

2

Screws

ST4.0×30

2

Screws

ST3.5×12

2

10

INSTALLATION(AIRDEFLECTOR):

Airdeflectorismentionedasincludedandnotoptional.

1. Beforeinstallation,curvebothendsofthebracketasshownbelow:

2. FixthebrackettotheT-shapedplasticoutletwith2pcsST3.5x12mm

screwsprovided.

3.Drill2holestoaccommodatethewallplugs,thenscrewandtightenthe

bracketontothewallwith2pcsST4x30mmscrewsprovided.

4.Attachtheexhaustpipeontotheairoutletofthecookerhoodasshownbelow:

5.Installthechimneytotheunitandfixit.

11

oi1MFBTFLJOEMZCFOPUFE5TIBQFEQMBTUJDPVUMFUBOEWGMBQTDBOOPU

CFVTFEBUUIFTBNFUJNF:PVDBOVTFUIFNJOUXPXBZT"EEW

GMBQPOFYJTUJOHPVUMFU6TF5TIBQFEQMBTUJDPVUMFUOPBEEW

GMBQw

oi/PUF5IFQSPEVDUJTQSPWJEFEXJUIWGMBQBDDFTTPSZ5IJT

BDDFTTPSZJTOPUNBOEBUPSZGPSJOTUBMMBUJPOPQFSBUJPOBOEVTFPG

UIFQSPEVDUw

12

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, exhaust pipe is not required and

the installation is similar to the one show in section “INSTALLATION (VENT

OUTSIDE)”.

Activated carbon filter can be used to trap odors.

In order to install the activated carbon filter, the grease filter should be

detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in clockwise direction.

Repeat the same on the other side.

NOTE:

oMake sure the filter is securely locked. Otherwise, it would loosen and

cause dangerous.

oWhen activated carbon filter attached, the suction power will be

lowere

13

Intended Use

Please read this user manual thoroughly before attempting to use this plasma filter

for the first time. This manual contains important information on safe installation, use

and care of this filter. Retain these instructions for future reference and pass on to the

next user.

This plasma filter can only be used safely if it is correctly installed according to the safety

instructions. The installer is responsible for ensuring that the appliance works correctly at its

installed location.

This plasma filter is intended for domestic use and household environment only. Do not use

the plasma filter for other uses than its specific purpose. Do not leave the appliance

unattended during operation.

This plasma filter is intended to remove airborne dust particles, pollen, micro-organisms

(house dust mites, bacteria, viruses and moulds), cigarette smoke and smells from the air.

Presence of smell will still be present when you are cooking and can only be completely

removed after you had finished your cooking. Harmful gases (carbon monoxide etc.) cannot

be removed.

The plasma filter produces ozone, the amount will depend on the time you use the filter.

When the plasma filter is placed in a well ventilated room, the amount emitted is within the

set safety limits and standard. A slight ionisation smell will be present during usage and do

not indicate a faulty connection or device

This appliance may be used by children over the age of 8 years old and by persons with

reduced physical, sensory or mental capacity or by persons with a lack of experience or

knowledge if they are supervised by someone who is responsible for their safety or have

been instructed in how to use the appliance safely and have understood the risks involved in

not using it properly.

Children must not play with the appliance. Cleaning and user maintenance must not be

performed by children unless they are over 15 years of age and are supervised. Keep

children below the age of 8 years old at a safe distance from the appliance and power cable.

Check the appliance for damage after unpacking it. Do not connect the appliance if it has

been damaged during transport.

Important

This plasma filter is intended for use in combination with an extractor hood

with metal grease filters

The manufacturer is not liable for any damage which is caused by

improper use or incorrect operation.

14

Operating Instructions

Warning: Only use the plasma filter in combination with an extractor unit with metal

grease filters. Always ensure that the plasma filter is in a location with good oxygen supply

and good permanent ventilation. Please refer to your extractor hood user manual.

Operating the Plasma Filter on the Extractor Hood

Touch the sensor buttons gently on the control panel on the extractor to operate this

appliance.

To achieve better air extraction, it is advisable to switch on the extractor hood a few minutes

before starting to cook and leave it on for approximately 15 minutes after cooking or at least

all cooking smell is completely removed.

The plasma filter uses a sensor switch that reacts to the air flow from the extractor hood.

When the extractor hood is switch ON, the air pass through a sensor to activate the plasma

filter automatically. It may take approximately 20 to 30 seconds to activate the plasma filter

depending on the type of extractor hood.

The indicator lamp on the plasma filter will light up and an audio signal will sound to indicate

that the plasma filter is now switch ON.

Cleaning the Plasma Filter

Little maintenance is needed as the plasma filter is cleaned automatically as soon as it is

put into operation. The electrodes exhibit a very long lifetime and are nearly

indestructible in destined operation.

The activated carbon filter is regenerated at each process, keeps its pores clean and is

expected to last for not less than 6 years if the activated carbon filter is use for not more

than 4 hours a day. Usage of more than 4 hours a day will reduce the lifespan of the

activated carbon filter.

Note: It is important to follow the maintenance instructions of your extractor hood. The

grease filter must be clean regularly and/or replace at appropriate intervals to prevent

contamination.

Periodic Maintenance for Plasma Filter

To ensure that your plasma filter is in satisfactory working condition, contact your local After

Sales Center once every 5 years to do periodic inspection on the plasma filter.

15

Trouble Shooting

Problem

Possible Cause

Solution

The Plasma Filter

Does Not Work

No electricity supply

Check power plug is connected properly and

main power switch is turned on

Faulty Fuse

Check the fuse box of the plasma filter to

ensure fuse is not blown

Power Trip

Check if other electrical appliance are working

The Indicator Lamp

on the Plasma Filter

Did Not Light Up

Air Sensor Switch might be

faulty

Please contact your local After Sales Center

PCB Board Failure

16

Wi-Fi Connection

Long press WiFi icon and enter into connecting mode: the backlit of WiFi icon

keep flashing indicate the connection is under connecting, the backlit of WiFi

icon is light on indicate it is connected, same for standby mode; long press

WiFi icon again and the connection will be stopped;

DESCRIPTION OF COMPONENTS

OPERATION

Boost 1(speed 4)

Press speed b button 1, the backlit of speed B button is on, and the cooker

hood is working at boost mode ;

Boost 2(speed 5)

Press speed b button 2, the backlit of speed B+ button is on, and the

cooker hood is working at boost mode ;

Light

Short press for lighting on & off

Quick timer: Long press the light button hold for 3 seconds, fan speed

buttons will flashing & into 5minutes count down, after 5 minutes motor &

light will turn off automatic with three Buzzer sound.

Medium Speed button

Airflow speed is ideally for ventilation in standard cooking operation.

High Speed button

When high density of smoke or steam produced, press high-speed button

for high effective ventilation.

CONFIGURATION 1

Low Speed button

It’s used for Ventilation on the kitchen. It is suitable for simmering and

cooking which do not make much steam.

17

STANDBY MODE.

After plug in, all lighting, system in

STANDBY MODE

.

Medium Speed button

Airflow speed is ideally for ventilation in standard cooking operation.

High Speed button

When high density of smoke or steam produced, press high-speed button

for high effective ventilation.

Booster function

This hood has a booster function. To activate the booster, Press

to speed 4, enter into highest speed while the hood is in use and it will

increase speed for 5 minutes, before slowing down again.

Light

Short press for lighting on & off

Quick timer: Long press the light button hold for 3 seconds, fan speed

buttons will flashing & into 5minutes count down, after 5 minutes motor &

light will turn off automatic with three Buzzer sound.

CONFIGURATION 2

Wi-Fi Connection

Long press WiFi icon and enter into connecting mode: the backlit of WiFi

icon keep flashing indicate the connection is under connecting, the

backlit of

WiFi icon is light on indicate it is connected, same for standby

mode; long press WiFi icon again and the connection will be stopped;

Low Speed button

It’s used for Ventilation on the kitchen. It is suitable for simmering and

cooking which do not make much steam.

18

La page charge ...

Haier HATS9CBS6BPLWI Manuel utilisateur

Haier HATS9CBS6BPLWI Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents