Alesis DM10 MKII Pro Kit Manuel utilisateur

User Guide

English ( 2 – 15 )

Guía del usuario

Español ( 16 – 29 )

Guide d’utilisation

Français ( 30 – 44 )

Guida per l’uso

Italiano ( 45 – 58 )

Benutzerhandbuch

Deutsch ( 59 – 73 )

Appendix

English ( 74 – 78 )

2

User Guide (English)

Introduction

Box Contents

DM10 MKII Pro Module

Power Adapter

User Guide

Safety & Warranty Manual

Support

For the latest information about this product (system requirements, compatibility information,

etc.) and product registration, visit alesis.com.

For additional product support, visit alesis.com/support.

Features

Top Panel

1

2

4

5

6

8

9

12

11

15

13

14

7

3

12

16

17

18

22

19

2120

10

1. Power Button: Press this button to power the drum module on or off.

2. Display: This screen shows various menus and options to help you configure and use the

drum module. See Operation to learn more.

3. Function Buttons: These buttons allow you to navigate the menus shown in the LCD. Press

an F-Button to select the "virtual" button or tab shown above it in the LCD.

4. Enter: Press this to confirm your selection or to enter a submenu.

5. Exit: Press this button to cancel your selection or to exit a submenu.

6. Up: Press this button to move up one option in the display.

7. Down: Press this button to move down one option in the display.

3

8. Dial: Turn this dial to adjust the setting of the currently selected item in the display

(number values, kits, songs, etc.). Alternatively, use the Up and Down buttons.

9. Master Volume: Turn this knob to adjust the volume level of the outputs on the rear panel.

10. Aux Volume: Turn this knob to adjust the volume of an external sound source connected to

the Aux Input on the rear panel.

11. Phones Volume: Turn this knob to adjust the volume level of the phones output on the

rear panel.

12. Save Buttons: Press and hold these buttons for 2 seconds to save a favorite or frequently

used menu. Briefly press these buttons to jump directly to the saved page. See Operation

> Memory to learn more.

13. Tempo: Press this button to view the current tempo in the display. See Operation >

Metronome to learn more.

14. Play/Stop: Press this button to play or stop a song. When the drum module is record-

armed, press this button to start recording.

15. Click: Press this button to activate or deactivate the built-in metronome (“click”). When

you activate it, the Metronome settings will also appear in the display, which you can

adjust. See Operation > Metronome to learn more.

16. Record: Press this button to record-arm the drum module. To start recording, hit a drum

pad, press Enter, or press Play/Stop. To cancel recording, press Exit or Record.

17. Song: Press this button to access the Song Selection page in the display. This lets you

play along with MP3, WAV, and MIDI songs on the module or an external USB drive.

18. C

oach: Press this button to access the Coach mode in the display. See Operation >

Coach to learn more.

19. USB Memory: Press this button to access the USB Memory page in the display. See

Operation > USB Drive to learn more.

20. Utility: Press this button to access the Utility page in the display. See Operation > Utility

to learn more.

21. Trigger: Press this button to access the Trigger settings page in the display. See

Operation > Trigger Settings to learn more.

22. Kit: Press this button to access the Kit Selection page in the display. See Operation >

Kits to learn more.

4

Rear Panel

1

2

3

4 5 6 7 8

9

10

1. Phones Output: Connect 1/4” (6.35 mm) stereo headphones (sold separately) to this

output. Control the volume by turning the Phones Volume knob on the top panel.

2. USB MIDI/Audio Port: Connect this USB port to a computer using a standard USB cable.

The drum module will send MIDI messages and audio to and from your computer over this

connection.

3. USB Port: Connect a USB flash drive to this USB port to record songs to it, load samples

from it, or save and load kits, songs, and triggers. See Operation > USB Drive to learn

more.

Important: Your USB flash drive must use a FAT32 file system to work properly with the

drum module.

4. MIDI Out/Thru: Connect an external MIDI device (synthesizer, sound module, etc.) to this

output using a standard 5-pin MIDI cable.

5. MIDI In: Connect an external MIDI device (sequencer, drum machine, etc.) to this input

using a standard 5-pin MIDI cable.

6. Outputs: Connect your audio interface, mixer, powered monitors, etc. to these outputs

using standard 1/4” (6.35 mm) TS cables.

7. Tom 4 Trigger Input: Connect the Tom 4 drum pad to this input. Refer to the Assembly

Guide for more information.

8. Crash 2 Trigger Input: Connect the Crash 2 cymbal pad to this input. Refer to the

Assembly Guide for more information.

9. Aux Input: Connect an additional audio player (smartphone, tablet, etc.) to this input using

a standard 1/8” (3.5 mm) stereo/TRS cable. The sound will be mixed with the drum

module’s sounds.

10. Power Input: Connect this input to a power outlet using the included power adapter.

5

Setup

Items not listed in

Introduction > Box Contents are sold separately.

Getting Started

1. Make sure all devices are off and all volume knobs are set to "zero."

2. Connect the cable snake to the port on the bottom of the DM10 MKII Pro module (using

the two screws to secure it), and then connect the 1/4” ends of the cables to their

respective pads.

3. Connect any input sources (CD player, smartphone, etc.) to the Aux input on the DM10

MKII Pro.

4. Connect output devices (amplifier, mixer, etc.) to the Outputs on the DM10 MKII Pro.

5. Plug all devices into power sources, and turn on devices in proper order:

• When starting a session, turn on (1) input sources, (2) DM10 MKII Pro, (3) output

devices.

• When ending a session, turn off (1) output devices, (2) DM10 MKII Pro, (3) input

sources.

6. Use the Down and Up buttons to select a kit, and use the dial to adjust the volume of the

kit.

7. Hit the pads and slowly adjust the master volume and/or phones volume until an

appropriate level is reached.

8. When finished, be sure to set all volume knobs back to “zero” before powering off DM10

MKII Pro.

Note: DM10 MKII Pro will automatically power off if no activity is detected for 30 minutes.

You can enable or disable this function in the Utility page.

Computer

Headphones

Monitors

Power

External MIDI Device

Cable Snake to

Drum Pads

6

Operation

Kits

A kit in the drum module is a selection of sounds that you can play with the pads of your

electronic drum kit. Kits 01–50 are Presets, and kits 51–80 are User Kits. You can edit the

parameters of all drum kits (01–80) and save them into user kits (51–80).

Selecting a Kit

Press Kit to enter the Kit Interface page. There are two parameters on the main kit interface–

kit number and kit volume. From here, use the Down and Up buttons to select a kit, and use

the dial to adjust the volume of the kit.

On this page:

• Press the F1 button to enter the Kit List menu.

• Press the F2 button to enter the Kit Edit menu.

• Press the F3 button to switch the X-stick on or off.

To select a kit:

1. Press Kit to enter the Kit Interface page (if you are not already viewing it).

2. Press the F1-List button to display the Kit List menu.

3. Use the Dial or Down and Up buttons to scroll through the list of kits. Press the F1-Preset

button to quickly jump to the Preset kits, or press the F3-User button to quickly jump to

the User Kits. The LED under the Kit button will indicate the type of kit selected.

4. To preview a kit, press the F2-PRVW button and play.

5. Kits will automatically be loaded as they are selected. Press Exit to return to the Kit

Interface page.

Note: To learn how to select a kit on a USB flash drive, see the USB Drive chapter.

Editing a Kit

You can change certain parameters of each kit, letting you customize its overall sound. Kit

parameters include the voices and effects for each trigger. When any parameter is changed,

you must save the kit before exiting the Kit Menu to keep the changes.

To edit a kit:

1. Press Kit to enter the Kit Interface page (if you are not already viewing it).

2. Press the F2 button to enter the Kit Edit menu.

3. On this page:

• Press the F1 button to enter the Voice Edit menu.

• Press the F2 button to enter the Effect Edit menu.

• Press the F3 button to enter the Save menu. See Saving a Kit to learn how to do this.

7

In a kit, each sound is called a “voice.” You can change each voice and set some of its

parameters, letting you customize the collection of sounds in a kit.

To edit a voice:

1. Enter the Kit Edit menu (if you are not already viewing it).

2. Press the F1-Voice button to enter the Voice Edit menu.

3. Hit the pad whose voice you want to edit. The pad’s name will appear at the top of the

display.

4. The display will show the pad’s current voice and its parameters. On this page:

• To select a parameter that you want to edit, use the Down and Up buttons:

o Voice Number: The pad’s current voice (001–758) and User Voices, up to 99).

o Volume: The pad’s volume (000–127).

o Pitch: The pad’s pitch offset in semitones (-08 to +08).

o Pan: The pad’s position in the stereo field (L8 to C to R8).

o Decay: The amount of time it takes for the pad’s sound to decay (-05–00). 00 is

the default and the longest amount of time. -05 is a very short time.

o Reverb Level: The amount of reverb effect applied to the pad’s sound (000–

127).

o FX Level: The amount of effects applied to the pad’s sound (000–127).

o MIDI Note:

When the drum module’s USB MIDI port or MIDI Out is connected to

a computer or external MIDI device, the pad will send this MIDI note to it. If you are

not using those connections, this setting will not affect the trigger or its sound.

Kick Drum 36 Tom 3 (Rim) 58 Crash 2 57

Snare Drum (Center) 38 Tom 4 (Center) 41 Crash 2 (Edge) 52

Snare Rim 40 Tom 4 (Rim) 39 Hi-Hat Open 46

Tom 1 (Center) 48 Ride Bow 51 Hi-Hat Open (Edge) 26

Tom 1 (Rim) 50 Ride Edge 59 Hi-Hat Closed 42

Tom 2 (Center) 45 Ride Bell 53 Hi-Hat Closed (Edge) 22

Tom 2 (Rim) 47 Crash 1 49 Hi-Hat Pedal 44

Tom 3 (Center) 43 Crash 1 (Edge) 55 Hi-Hat Splash 21

o Pad Pattern: The song that starts when you hit the pad. The song will stop when

you hit it again.

o Min Velocity: The minimum velocity needed to trigger the pad’s sound.

o Strainer: The tightness of the snare wires on the snare drum (Off, Loose, Low,

Medium, or Tight).

Note: Not all instruments have a snare strainer effect.

o Muffling: The muffling effect of the snare, toms, and kick only (Off, 1 to 4).

o Head Tuning: The tuning of the pad’s head (-63 to +63).

o Size: The size of the cymbal (-63 to +63). This setting only applies to cymbals.

o Sustain: The amount of sustain of the cymbal (-63 to +63). This setting only

applies to cymbals.

• To edit the parameter’s setting or value, use the dial.

5. When you are done editing, you must save the kit before exiting the Kit Edit menu. See

below to learn how to do this.

8

You can apply effects such as reverb or EQ to your kit, as well as to up to 3 individual triggers.

To edit effects parameters:

1. Enter the Kit Edit page (if you are not already viewing it).

2. Press the F2-Effect button to enter the Effect Edit page.

3. Use the Down or Up buttons to select your desired item: Kit FX, Kit Reverb, Kit EQ, Kit

Compress, or Voice FX. Press Enter to continue.

4. To select a parameter that you want to edit, use the Down and Up buttons. To edit the

parameter’s setting or value, use the dial. See Appendix > Effects Parameters > Kit

Effects for more information on kit parameters.

5. When you are done editing, we recommend saving the kit. See below to learn how to do

this.

Saving a Kit

You can also save the current sounds and settings as a user kit.

To save a kit:

1. Press Kit to enter the Kit Interface page (if you are not already viewing it).

2. Press F2-Edit to enter the Kit Edit page.

3. When you have finished editing your parameters, press F3-Save to enter the Kit Save

menu.

4. Use the dial or Up or Down buttons to select the kit you want to save.

5. Press F3-Enter to continue, or press F2-Exit to return to the previous menu. Rename will

appear at the top of the display.

6. Optional: On this page:

• To change the currently selected character, turn the dial.

• To move to the next or previous character, press the Up or Down buttons.

• To insert a character, press F1-Insert.

• To delete a character, press F2-Delete.

7. After entering the name of the new kit, press F3-Enter to continue saving the kit, or F2-

Exit to cancel and return to the Kit Selection page.

8. If the save operation is successful, Save OK! will appear briefly in the display.

To cancel the operation at any point, press Exit.

Note: To learn how to save a kit to a USB flash drive, see the USB Drive chapter.

9

Trigger Settings

The drum module also lets you customize the settings of each trigger (drum pad or cymbal

pad). You can change its parameters, letting you customize your kit to your playing style.

These settings are “global” and therefore apply to all kits. DM10 MKII Pro has a set of preset

trigger settings and 5 user adjustable trigger settings.

To edit your trigger setting:

1. Press Trigger to enter the trigger interface page.

2. Hit the pad whose voice you want to edit. The pad’s name will appear at the top of the

display. Alternatively, use the Down or Up buttons to select the pad’s name at the top of

the display, and then use the dial to change it.

3. The display will show the current trigger and its parameters. On this page:

• To select a parameter that you want to edit, use the Down and Up buttons (not all

parameters are available for all pads):

o Threshold: The amount of force required to trigger the sound.

o Head Sensitivity: The sensitivity of the head (center) of a drum pad. Higher

values let you produce louder sounds with less force. Lower values require more

force to produce quieter sounds.

o Rim Sens: The sensitivity of the rim of a drum pad. Higher values let you

produce louder sounds with less force. Lower values require more force to

produce quieter sounds.

o X-Stick Level: The amount of cross-stick produced when the rim is struck.

Higher values increase the probability that the cross-stick sound will play when

the rim is hit. When set to 0, only the rimshot sound will play when the rim is hit.

o Head-Rim Adj: The amount of crosstalk reduction between the head (center)

and rim of a drum pad. Higher values reduce the probability that the pad’s rim

sound will be triggered when you play its head only and vice versa (due to the

force being transferred through the pad). Don’t set this value too high, though! If

this value is too high, you may not be able to trigger its sound if you intentionally

play both the head and rim at the same time; it may be silenced because the

module incorrectly interprets the hit as crosstalk.

o Curve: The velocity curve of the pad. This controls the relationship between the

amount of playing force and the volume level of the pad’s sound.

o X-Talk: The amount of crosstalk reduction. Higher values reduce the probability

that the pad’s sound will be triggered when you play another pad (due to the

force being transferred through a rack, through the floor, etc.). Don’t set this

value too high, though! If this value is too high, you may not be able to trigger its

sound if you play another pad at the same time; it may be silenced because the

module incorrectly interprets the hit as crosstalk.

o Retrig Cancel: The required amount of time between successive hits of the pad

to produce the sound for both hits. If the value is too low, you may hear multiple

hits (or “flams”) occur after striking the trigger once. If the value is too high, you

may hear missed notes when playing faster or rolling.

• To edit the parameter’s setting or value, use the dial.

4. To save your changes, press F3-Save. Otherwise, your changes will be lost when you

power off the drum module. See below to learn how to do this.

5. Press Exit to return to the previous page.

10

To save your trigger setting:

1. While viewing the Trigger Interface page, press F3-Save.

2. Select one of the five user trigger slots. An asterisk (*) next to a setting indicates that the

trigger is unused.

3. Press F3-Enter to select to continue, or press F2-Exit to return to the previous menu.

Rename will appear at the top of the display.

4. Optional: On this page, you can rename the trigger using the same process as Kit

Rename.

5. After entering the name of the new trigger setting, press F3-Enter to continue saving the

trigger setting, or F2-Exit to cancel and return to the trigger interface page.

Note: To learn how to save a trigger setting to a USB flash drive, see the USB Drive chapter.

To load a trigger setting:

1. Press Trigger to enter the trigger interface page (if you are not already viewing it).

2. While viewing the trigger interface page, press F2-Load.

3. Choose the trigger setting that you want to load using the dial or Down and Up buttons.

4. Press F3-Enter to load the trigger setting, or press F2-Exit to cancel and return to the

trigger interface page.

5. If the load operation is successful, Load OK! will appear briefly in the display. You will

then be returned to the trigger interface page.

Note: To learn how to load a trigger setting to a USB flash drive, see the USB Drive chapter.

Metronome

The built-in metronome (or “click track”) can help you keep a steady tempo while playing.

To activate or deactivate the metronome, press Click.

When you activate the metronome, its settings will also appear in the display, which you can

adjust.

1. To select a parameter that you want to edit, use the Down and Up buttons:

• Voice: the sound played for the metronome (Click, Clave, Stick, CoClick, FmClick,

Voice1, or Voice2).

• Volume: The volume of the click (000–127).

• Time Sig: The time signature of the click (0/2–9/2; 0/4–9/4; 0/8–9/8; or 0/16–9/16).

• Interval: How often the metronome clicks (1/2, 3/8, 1/4, 1/8, 1/12, or 1/16)

• Output: Sets whether the metronome plays through all of the module’s outputs (All)

or just the phones output (Phones).

To change the setting or value, use the dial.

2. To exit the page, press Exit, or press Click to deactivate the metronome.

To change the tempo:

1. Press Tempo. The current tempo will appear in the display.

2. Use the dial set the tempo.

3. Press Exit or Tempo to return to the previous page.

11

Record

You can record on the DM10 MKII Pro in two ways, MIDI and MP3. When no USB drive is

connected, only MIDI recording is available.

To record MIDI or USB files:

1. Press the Record button. By default, this will enter MIDI record mode.

To record MP3 when a USB drive is connected, press the F2-USB button.

2. To select a parameter that you want to edit, use the Down and Up buttons:

• Pattern: Select a preset pattern (001–100) or turn off.

• Tempo: The tempo of the recording (30–280 BPM).

• Time-Signature: The time signature of the recording (0/2–9/2; 0/4–9/4; 0/8–9/8; or

0/16–9/16). This parameter is only adjustable when Pattern is set to off.

• Precount: Play a one measure introduction before recording (on) or start recording

immediately (off).

To change the setting or value, use the dial.

3. Press F3-Start or hit a pad to start recording. The Metronome will turn on automatically

when you want to record. To turn off the Metronome, press the Click button. If you do

record with the Metronome on, only the background music and drum voices will be

recorded.

Note: During recording, only the F3-Stop, Click, and Start/Stop buttons are available.

4. When you have finished recording, press the F3-Stop or Start/Stop buttons to stop

recording and proceed to the rename page. Rename will appear at the top of the display.

5. Optional: On this page, you can rename the recording using the same process as Kit

Rename.

Note: Filenames can be a maximum of 12 characters.

6. When you have finished, press the F3-Enter or Enter buttons to save the recording. Press

Exit to exit the naming menu and return to the previous page.

Note: To learn how to save and load songs from a USB flash drive, see the USB Drive

chapter.

Coach

The Coach function lets you develop your timing, accuracy, and speed skills with three

different practice modes.

(F1) Quiet Count

In Quiet Count mode, a drum loop will repeat, alternating between (1) the drum pattern itself,

and (2) a metronome track of the same length during which you play the drum pattern yourself.

To use Quiet Count:

1. Press Coach to enter Coach mode, then press F1-Quiet to enter Quiet Count.

2. To select a parameter that you want to edit, use the Down and Up buttons: Beat Type

(half note, quarter note, eighth note, eighth note triplet, or sixteenth note), Mode (how

many measures alternate; 1-1, 2-2, or 1-3), and Measure Hint (turns on or off the accent

hint). To change the setting or value, use the dial.

3. Press Play/Stop to start practice. The display will show the accuracy of your playing,

indicating if you are behind, on, or ahead of the beat.

4. Press Play/Stop again to stop practice.

12

(F2) Beat Check

Beat Check mode evaluates your sense of time and how accurately you play along with the

metronome. To use Beat Check:

1. Press Coach to enter Coach mode, then press F2-Beat to enter Beat Check.

2. To select a parameter that you want to edit, use the

Down and Up buttons: Beat Type (001–015, see

right), Score (turns on or off the score function, which

grades your performance), and Measure Hint (turns

on or off the accent hint). To change the setting or

value, use the dial.

3. Press Play/Stop to start practice. The display will show the accuracy of your playing,

indicating if you are behind, on, or ahead of the beat.

4. Press Play/Stop again to stop practice.

(F3) Change Up

Change Up mode helps you practice changing rhythms while still maintaining accurate time.

To use Change Up:

1. Press Coach to enter Coach mode, then press F3-Change to enter Change Up.

2. To select a parameter that you want to edit, use

the Down and Up buttons: Beat Type (001–003,

see right), Score (turns on or off the score

function, which grades your performance), and

Measure Hint (turns on or off the accent hint).

To change the setting or value, use the dial.

3. Press Play/Stop to start practice. The display will show the accuracy of your playing,

indicating if you are behind, on, or ahead of the beat.

4. Press Play/Stop again to stop practice.

Utility

The Utility menu lets you configure various settings for the module itself. Press the Utility

button to enter the Utility menu, and use the Down and Up buttons to select from the options

below. Press Exit to return to the previous page.

Master Effect

Use this page to adjust the Master EQ and Master Compressor effect settings. These will be

applied to all kits and songs. See Appendix > Effects Parameters > Master Effects to learn

more.

Master Setup

Use this page to adjust the MIDI and Power settings.

• Soft Through: Allows the MIDI In data to be passed through to the MIDI Out.

• Local Control: When activated (On), playing the pads connected to the drum module will

trigger the drum module’s internal sounds. When deactivated (Off), playing the pads will

send MIDI notes from the drum module to a connected computer or MIDI device.

13

• GM Mode: When activated (On), MIDI messages sent into the drum module’s MIDI In will

trigger sounds from the General MIDI (GM) specification. When deactivated (Off), MIDI

messages sent into the drum module’s MIDI In will trigger the module’s internal sounds

(the ones played by each kit).

• Prog Change RX: Turn On to receive Program Change MIDI data in Channel 10, or turn

Off to ignore.

• Prog Change TX: Turn On to send Program Change MIDI data on Channel 10 when

changing kits, or turn Off to not send.

• Auto Power Off: This feature sets the drum module to power off automatically if it is not

used for a certain amount of time. You can set this to 30 minutes, 60 minutes, or turn it

off (Off).

User Voice

Use this page to manage the module’s internal memory.

• Delete Voice: Use this menu to delete a user voice.

i. Select Voice Delete and press Enter.

ii. Use the Down and Up buttons to select the voice that you want to delete, and then

press Enter.

iii. The display will show a warning that the memory will not be released immediately

when the voice is deleted. Press Enter again to continue and delete the voice, or

press Exit to return to the previous page.

• Clear Deleted Voices: When a user voice has been deleted, the corresponding memory

space cannot be released right away. Use the Clear Deleted Voices menu to clear this

memory so you can add more user samples.

i. Select Clear Deleted Voices and press Enter.

ii. The display will show a warning that clearing the deleted user voices can take a long

time. Press Enter again to continue the process, or press Exit to return to the

previous page.

iii. After the voice clearing has finished, the module will restart automatically.

Factory Set

Use this page to reset user drum kits, songs, voices, and trigger settings to factory defaults.

Select an option below using the Down and Up buttons and then press Enter to perform a

reset. Press Exit to return to the previous page.

• Kit: Resets only the user kit settings.

• Song: Resets only the user songs.

• Voice: Resets only the user voices.

• Trigger: Resets only the user trigger settings.

• All: Resets all user settings.

14

USB Drive

You can use the drum module with a USB flash drive save and load your data. Your USB flash

drive can have a capacity of 4–64 GB, and it must use a FAT32 file system to work properly

with the drum module.

IMPORTANT: We recommend plugging your USB flash drive into the module before loading

any files to it. This will create new folders to store Kits, Songs, Triggers, and Voices. When

adding files, make sure they are placed in the correct folder so they can be recognized by the

module. For instance, place WAV files in the Voice folder when loading your own samples.

Load

You can load four types of data from a USB flash drive—Kits, Songs, Triggers, and Voices.

The process for loading kits, songs, and triggers is the same. For songs and triggers, follow

the directions for loading kits below, but replace “kit” with “song” or “trigger.”

To load a kit from a USB flash drive:

1. Press USB Mem to enter the USB Memory menu.

2. Press the F1-Load button to enter the loading page (if you are not already viewing it).

3. Use the Down or Up buttons to select Kit, then press Enter to open the loading menu. A

list of your kits will appear in the display.

4. Use the Down and Up buttons to select a kit, and then press Enter.

5. Use the Down and Up buttons to select the desired “destination” user kit number. An

asterisk (*) next to a user kit name indicates that the kit is unused.

6. Press Enter to select the “destination” user kit number, or press Exit to return to the

previous menu. Rename will appear at the top of the display.

7. Optional: On this page, you can rename the kit using the same process as Kit Rename.

8. Press F3-Enter to load the kit or F2-Exit to cancel. You may need to wait a minute for the

kit to load, depending on its size.

You can also load your own samples to use as voices within a kit. Each sample must be a 16-

bit WAV file, with a total maximum size of 16 MB. It can have a sampling rate of 48, 44.1, 32

,

22.05, or 11.025 kHz.

To load a sample from a USB flash drive and create a user voice:

1. Press USB Mem to enter the USB Memory menu.

2. Press the F1-Load button to enter the loading page (if you are not already viewing it).

3. Use the Down or Up buttons to select Voice, then press Enter to open the loading menu.

A list of your samples will appear in the display.

4. Use the Down and Up buttons to select a sample, and then press Enter.

5. Use the Down and Up buttons to select from the options below:

• Velo Point: The velocity point separates Layer A and Layer B. Values above the point

will activate Layer A, and values below the point will activate Layer B. If the velocity

point is set to 127, the voice is only one layer and Wave B will be unselectable.

• Wave A: The sample for the first layer of the voice.

• Wave B: The sample for the second layer of the voice.

To edit the parameter’s setting or value, use the dial.

6. Press F3-Enter to confirm loading the sample, or press F2-Exit to return to the previous

menu. You may need to wait a minute for the sample to load, depending on its size. When

the sample has successfully loaded, the display will show Load OK and enter the

renaming menu. Rename will then appear at the top of the display.

15

7. Optional: On this page, you can rename the sample using the same process as Kit

Rename.

8. After entering the name of the voice, press F3-Enter to save the voice to the module.

9. Restart the module by powering it off and then back on using the power button to make

the new voice available to use.

Save

There are three types of data you can save to a USB flash drive—Kits, Songs, and Triggers.

The process is the same for all three. For songs and triggers, follow the directions for saving

kits below, but replace “kit” with “song” or “trigger.”

To save a kit to a USB flash drive:

1. Press USB Mem to enter the USB Memory menu.

2. Press the F2-Save button to enter the saving page.

3. Use the Down and Up buttons to select the kit number you want to save. An asterisk (*)

next to a user kit name indicates that the kit is unused.

4. To save the kit to the selected number, press F3-Enter. Press F2-Exit to return to the

previous page. Rename will appear at the top of the display.

5. Optional: On this page, you can rename the kit using the same process as Kit Rename.

6. After entering the name of the kit, press F3-Enter to save the kit to the USB drive. The

display will then return to the USB Memory menu.

To cancel, press Exit.

Format

To erase all data from your USB flash drive, use the format function.

To format a connected USB flash drive:

1. Press USB Mem to enter the USB Memory menu.

2. Press the F3-Format button to format the USB flash drive.

3. The display will show Format the USB Memory! Exit/Enter?

To format the drive (which will also erase its contents), press Enter. The display will show

Waiting! while the card is being formatted.

To cancel formatting, press Exit.

Memory

The Save buttons let you store some of your favorite or frequently used menus so you can

quickly access them with the press of a button.

Note: The Save buttons cannot be used in the Click, Record, Rename, and Tempo menus.

To save a menu to memory, navigate to the menu you wish to save and then press and hold

one of the Save buttons for 2 seconds. The display will show M1 function has saved to

indicate the save was successful.

Note: When Save is used in the Song or Kit menus, the selected song or kit number will also

be saved.

To load a saved menu from memory, briefly press the corresponding Save button.

16

Guía del usuario (Español)

Introducción

Contenido de la caja

DM10 MKII Pro Module

Adaptador de alimentación

Guía del usuario

Manual sobre la seguridad y garantía

Soporte

Para obtener la información más completa acerca de este product (los requisitos del sistema,

compatibilidad, etc) y registro del producto, visite alesis.com.

Para soporte adicional del producto, visite alesis.com/support.

Características

Panel superior

1

2

45

6

8

9

12

11

15

13

14

7

3

12

16

17

18

22

19

2120

10

1. Botón de encendido: Pulse este botón para encender o apagar el módulo de batería.

2. Pantalla: Esta pantalla muestra diversos menús y opciones para ayudarle a configurar y

utilizar el módulo de batería. Consulte Funcionamiento para aprender más.

3. Botones de función: Estos botones le permiten navegar los menús mostrados en la pantalla

LCD. Pulse un botón F para seleccionar el botón "virtual" o la pestaña mostrada arriba en la

pantalla LCD.

4. Intro: Pulse este botón para confirmar su selección o para entrar a un submenú.

5. Salir: Pulse este botón para cancelar su selección o para salir de un submenú.

6. Arriba: Pulse este botón para desplazarse hacia arriba por las opciones en la pantalla.

7. Abajo: Pulse este botón para desplazarse hacia abajo por las opciones en la pantalla.

17

8. Cuadrante: Gire este cuadrante para cambiar el ajuste del elemento actualmente

seleccionado en la pantalla (valores numéricos, kits, canciones, etc.). Como alternativa,

utilice los botones de subir y bajar.

9. Volumen maestro: Gire esta perilla para ajustar el nivel de volumen de las salidas del

panel trasero.

10. Volumen de auxiliares: Gire esta perilla para ajustar el nivel de volumen de las fuentes de

sonido externas conectadas a las entradas Aux del panel trasero.

11. Volumen de auriculares: Gire esta perilla para ajustar el nivel de volumen de la salida

para auriculares del panel trasero.

12. Botones Save: Mantenga pulsados estos botones durante 2 segundos para guardar un

menú favorito o usado frecuentemente. Pulse brevemente estos botones para saltar

directamente a la página guardada. Consulte Funcionamiento > Memoria para aprender

más.

13. Tema: Pulse este botón para acceder a la página de selección de canción en la pantalla.

Consulte Funcionamiento > Metrónomo para aprender más.

14. Iniciar/parar: Pulse este botón para iniciar o detener una canción. Cuando el módulo está

preparado para grabar, pulse este botón para comenzar a grabar.

15. Clic: Pulse este botón para activar o desactivar el metrónomo (“clic”) integrado. Cuando lo

active, los ajustes de metrónomo también aparecerán en la pantalla, los cuales puede

ajustar. Consulte Funcionamiento > Metrónomo para aprender más.

16. Grabar: Pulse este botón para preparar el módulo de batería para grabar. Para comenzar

a grabar, golpee un pad, pulse Enter o Play/Stop. Para finalizar la grabación, pulse Exit o

Record.

17. Song: Pulse este botón para acceder a la página Song Selection (Selección de canción)

e

n la pantalla. Esto le permite tocar con canciones de acompañamiento MP3, WAV y MIDI

del módulo o una unidad USB externa.

18. Coach: Pulse este botón para acceder al modo Coach (Entrenador) en la pantalla.

Consulte Funcionamiento > Coach para aprender más.

19. USB Mem: Pulse este botón para acceder a la página USB Memory (Memoria USB) en la

pantalla. Consulte Funcionamiento > Unidad USB para aprender más.

20. Utility: Pulse este botón para acceder a la página Utility (Utilidad) en la pantalla. Consulte

Funcionamiento > Utilidad para aprender más.

21. Trigger: Pulse este botón para acceder a la página de ajustes Trigger (Disparador) en la

pantalla. Consulte Funcionamiento > Ajustes del disparador para aprender más.

22. Kit: Pulse este botón para acceder a la página de selección de kit en la pantalla. Consulte

Funcionamiento > Kits para aprender más.

18

Panel trasero

1

2

3

4 5 6 7 8

9

10

1. Salida para auriculares: Conecte auriculares estéreo de 6,35 mm (1/4 pulg.) a esta salida

(se venden por separado). Controle el volumen con la perilla Phones Volume (volumen de

auriculares) del panel superior.

2. Puerto USB MIDI/Audio: Conecte este puerto USB a un ordenador utilizando un cable

USB estándar. El módulo de batería enviará y recibirá mensajes MIDI y audio hacia y

desde su ordenador a través de esta conexión.

3. Puerto USB: Conecte una unidad de memoria USB a este puerto USB para grabar

canciones en la misma, cargar muestras desde ella o guardar y cargar kits, canciones o

disparadores. Consulte Funcionamiento > Unidad USB para aprender más.

Importante: Su unidad de memoria USB debe utilizar un sistema de archivos FAT32 para

funcionar correctamente con el módulo de batería.

4. Salida/pasante MIDI: Conecte un dispositivo MIDI externo (sintetizador, módulo de

sonidos, etc.) a esta salida mediante un cable MIDI estándar de 5 patillas.

5. Entrada MIDI: Conecte un dispositivo MIDI externo (secuenciador, caja de ritmos, etc.) a

esta entrada mediante un cable MIDI estándar de 5 patillas.

6. Salidas: Conecte su interfaz de audio, mezclador, monitores alimentados, etc. a estas

salidas utilizando cables TS estándar de 6,35 mm (1/4 pulg.).

7. Entrada de disparador Tom 4: Conecte a esta entrada el pad de tambor Tom 4. Para

más información, consulte la Guía de armado.

8. Entrada de disparador Crash 2: Conecte a esta entrada el pad de platillos Crash 2. Para

más información, consulte la Guía de armado.

9. Entrada auxiliar: Conecte una fuente de audio adicional (teléfono inteligente

[smartphone], etc.) a esta entrada mediante un cable estéreo/TRS de 3,5 mm (1/8 pulg.). El

sonido se mezclará con los sonidos del módulo de batería.

10. Entrada de corriente: Conecte esta entrada a un tomacorriente utilizando el adaptador de

alimentación incluido.

19

Instalación

Los elementos que no se enumeran en Introducción > Contenido de la caja se venden por separado.

Inicio rápido

1. Asegúrese de que todos los dispositivos estén apagados y que todos los faders y perillas de

ganancia estén ajustados a "cero".

2. Conecte el multicable al puerto de la parte inferior del módulo DM10 MKII Pro (usando los dos

tornillos para fijarlo) y a continuación conecte los extremos de 3,5 mm (1/4 pulg.) de los cables a

sus pads respectivos.

3. Conecte las fuentes de entrada (reproductor de CD, teléfono inteligente, etc.) a la entrada Aux

In del DM10 MKII Pro.

4. Conecte los dispositivos de salida (amplificador, mezclador, etc.) a las Outputs (Salidas) del

DM10 MKII Pro.

5. Enchufe todos los dispositivos a las fuentes de alimentación y enciéndalos en el orden correcto:

• Para iniciar la sesión, encienda (1) las fuentes de entrada, (2) el DM10 MKII Pro, (3) los

dispositivos de salida.

• Al terminar la sesión, invierta esta operación apagando (1) los dispositivos de salida, (2) el

DM10 MKII Pro y (3) las fuentes de entrada

6. Utilice los botones de subir y bajar para seleccionar un kit y el cuadrante para ajustar el

volumen del kit.

7. Toque los pads y ajuste lentamente el volumen de Master (Maestro) y/o Phones (Auriculares)

hasta que se alcance un nivel apropiado.

8. Cuando termine, asegúrese de ajustar todas las perillas de volumen nuevamente a “cero” antes

de apagar el DM10 MKII Pro.

Nota: El DM10 MKII Pro se apagará automáticamente si no se detecta actividad durante 30

minutos. Puede habilitar o inhibir esta función en la página Utility.

Dispositivo MIDI externo

Computadora

Auriculares

Monitores

Alimentación

Multicable a los

pads de tambor

20

Funcionamiento

Kits

Un kit del módulo de batería es una selección de sonidos que puede reproducir con los pads

de su batería electrónica. Los kits 01–50 son preestablecidos y los kits 51–80 kits del usuario.

Puede editar los parámetros de todos los kits de batería (01–80) y guardarlos en los kits del

usuario (51–80).

Cómo seleccionar un kit

Pulse Kit para entrar a la página Kit Interface (Interfaz de kits). La interfaz principal de kits

consta de dos parámetros—número y volumen del kit. A partir de aquí, utilice los botones de

subir y bajar para seleccionar un kit y el cuadrante para ajustar el volumen del kit.

En esta página:

• Mantenga pulsado el botón F1 para abrir el menú Kit List (Lista de kits).

• Pulse el botón F2 para entrar al modo Kit Edit (Edición de kits).

• Pulse el botón F3 para activar o desactivar la función X-stick.

Para seleccionar un kit:

1. Pulse Kit para abrir la página de interfaz de kits (si aún no se encuentra en ella).

2. Pulse el botón F1-List para mostrar el menú Kit List (Lista de kits).

3. Utilice el cuadrante o los botones Subir y Bajar para desplazarse por la lista de kits.

Pulse el botón F1-Preset para saltar rápidamente a los kits preestablecidos o el botón F3-

User para saltar rápidamente a los kits del usuario. El LED que está debajo del botón Kit

indica el tipo de kit seleccionado.

4. Para probar un kit, pulse el botón F2-PRVW y comience a reproducir.

5. Los kits se cargarán automáticamente a medida que se seleccionen. Pulse Exit para

volver a la página de interfaz de kits.

Nota: Para aprender a seleccionar un kit en una unidad de memoria USB, consulte el capítulo

Unidad USB.

Cómo editar un kit

Puede modificar ciertos parámetros de cada kit, pudiendo personalizar el sonido general. Los

parámetros del kit incluyen las voces y los efectos correspondientes a cada disparador.

Cuando se modifica cualquier parámetro, debe guardar el kit antes de salir del menú del kit a

fin de guardar los cambios.

Cómo editar un kit:

1. Pulse Kit para entrar a la página de selección de kits (si aún no se encuentra en ella).

2. Pulse el botón F2 para entrar el menú Kit Edit.

3. En esta página:

• Pulse el botón F1 para abrir el menú Voice Edit (Edición de voz).

• Pulse el botón F2 para abrir el menú Effect Edit (Edición de efectos).

• Pulse el botón F3 para abrir el menú Save (Guardar). Cuando termine la edición, le

recomendamos guardar el kit. Consulte Cómo guardar un kit para aprender a

hacerlo.

La page est en cours de chargement...

Alesis DM10 MKII Pro Kit Manuel utilisateur

Ce manuel convient également à

Alesis DM10 MKII Pro Kit Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents