Husqvarna 136 LiHD50 Le manuel du propriétaire

Catégorie
Taille-haies électriques
Taper
Le manuel du propriétaire
EE
EE
nn
nn
gg
gg
ll
ll
ii
ii
ss
ss
hh
hh
136 LiHD50
GB
Oper
ator’
s man
ual 2-23
SE
Br
uksan
visning 24-45
DK
Br
ugsan
visning 46-67
NO
Br
uksan
visning 68-89
FI
Käyttöohje 90-111
DE
Bedien
ungsanw
eisung 112-134
FR
Man
uel d’utilisation 135-157
NL
Gebr
uiksaanwijzing 158-179
ES
Man
ual de instr
ucciones 180-201
PT
Instr
uções par
a o uso 202-223
IT
Istr
uzioni per l’uso 224-245
H1154526-38,136 LiHD50,_1 v2.fm Page 1 Friday, February 10, 2012 3:20 PM
KEY
T
O SYMBOLS
2
English
Symbols on the mac
hine:
T
ranslation of the original Swedish operating instruction.
WARNING! Incorrect or
careless use of a hedge
trimmer can turn it into a
dangerous tool that can
cause serious or even
fatal injury. It is extremely
important that you read
and understand the contents of this operator's manual.
Always wear:
Approved hearing protection
Approved eye protection
This product is in accordance with
applicable EC directives.
Always wear approved protective
gloves.
Wear sturdy, non-slip boots.
Symbols on the product or its
packaging indicate that this product
cannot be handled as domestic
waste. This product must be
deposited at an appropriate
recycling facility.
Cutting tool. Do not touch the tool
without first deactivating the
machine.
Do not expose to rain.
Direct current
Noise emission to the environment
according to the European Community’s
Directive. The machine’s emission is
specified in the Technical data chapter
and on the label.
Symbols on the batter
y and on
the battery charger:
This product
must be
deposited at an
appropriate
recycling
facility.
Fail-safe transformer
Use and store battery charger only
indoors.
Double insulation
Other symbols/decals on the mac
hine refer to special
certification requirements for certain markets.
Symbols in the operator’
s
manual:
The machine is turned on and off by
pressing the on and stop button.
Always wear approved protective
gloves.
Regular cleaning is required.
Visual check.
Protective goggles or a visor must be
worn.
Remove the battery. IMPORTANT!
Always remove the battery to prevent
the machine being started by accident.
Li-ion
Li-ion
Li-ion
H1154526-38,136 LiHD50,_1 v2.fm Page 2 Friday, February 10, 2012 3:20 PM
KEY
T
O SYMBOLS
English
3
Y
ou will find the following labels on your hedge trimmer,
battery and battery charger:
Husqvarna 136 LiHD50 578 46 36-01
Husqvarna 136 LiHD50 578 46 36-01
s/n XXXX XXXXXXX
s/n XXXX XXXXXXX
36V
36V
Husqvarna AB
Husqvarna AB
Huskvarna SWEDEN
Huskvarna SWEDEN
H1154526-38,136 LiHD50,_1 v2.fm Page 3 Friday, February 10, 2012 3:20 PM
CONTENTS
4
English
Contents
Note the f
ollowing before
starting:
Please read the oper
ator's manual carefully.
KEY
TO SYMBOLS
Symbols on the machine:
...................................... 2
Symbols on the battery and on the battery charger:
2
Symbols in the operator’s manual: ........................ 2
CONTENTS
Contents
............................................................... 4
Note the following before starting: ........................ 4
INTR
ODUCTION
Dear Customer
, ..................................................... 5
WHA
T IS WHAT?
What is what?
....................................................... 6
GENERAL SAFETY PRECA
UTIONS
Gener
al power tool safety warnings ...................... 7
Personal protective equipment ............................. 9
Battery and battery charger .................................. 9
Machine
s safety equipment ................................. 11
B
ATTERY HANDLING
Batter
y .................................................................. 13
Battery charger ..................................................... 13
Transport and storage ........................................... 14
Disposal of the battery, battery charger and
machine ................................................................
14
ST
ARTING AND STOPPING
Chec
k before starting ............................................ 15
Connect battery to the machine ............................ 15
Starting and stopping ............................................ 15
W
ORKING TECHNIQUES
Gener
al working instructions ................................ 17
MAINTENANCE
Inspection and maintenance
................................. 19
Cleaning and lubrication ....................................... 19
Troubleshooting schedule ..................................... 20
Maintenance schedule .......................................... 21
TECHNICAL D
ATA
T
echnical data ....................................................... 22
EC-declaration of conformity ................................ 23
!
W
ARNING! Long-term exposure to noise
can result in permanent hearing
impairment. So always use approved
hearing protection.
!
W
ARNING! Under no circumstances may
the design of the machine be modified
without the permission of the
manufacturer. Always use original
accessories. Non-authorized
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
!
W
ARNING! Incorrect or careless use of a
hedge trimmer can turn it into a
dangerous tool that can cause serious or
even fatal injury. It is extremely important
that you read and understand the
contents of this operator's manual.
H1154526-38,136 LiHD50,_1 v2.fm Page 4 Friday, February 10, 2012 3:20 PM
English
5
INTR
ODUCTION
Dear Customer
,
Cong
ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,
when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production
of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-
powered plant. During the more than 300 years in existence, the Husqvarna factory has produced a lot of different
products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first
motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working
today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our
highest priority. The business concept is to develop, manufacture and market motor-driven products for forestry and
gardening, as well as for the building and construction industry. Husqvarna
s aim is also to be at the front edge for
ergonomics, usability, security and environmental protection. That is the reason why we have developed many different
features to add to our products within these areas.
We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very
long time to come. The purchase of one of our products gives you access to professional help with repairs and service
whenever this may be necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the
address of your nearest service workshop.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this
operator
s manual as a valuable document. By following its content (usage, service, maintenance, etc), the life span and
the second-hand value of the machine can be extended. If you sell this machine, make sure that the operator
s manual
is passed on to the buyer.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
H1154526-38,136 LiHD50,_1 v2.fm Page 5 Friday, February 10, 2012 3:20 PM
6
English
WHA
T IS
WHA
T?
What is what?
10
1
2
3
4
5
6
7
9
11
12
16
17
13
15
14
15
18
8
19
1
Operator
s manual
2 Rear handle
3 Power trigger lockout
4 Front handle
5 Cutter
6 Transport guard
7 Power trigger
8 Control panel
9 Hand guard
10 Battery
11 Battery charger
12 Cord
13 Battery indicator button
14 Battery status
15 Warning indicator
16 SavE button
17 Activate and deactivate button
18 Power on and warning indicator
19 Battery release buttons
H1154526-38,136 LiHD50,_1 v2.fm Page 6 Friday, February 10, 2012 3:20 PM
GENERAL SAFETY PRECA
UTIONS
English
7
General po
wer tool safety
warnings
Please read the oper
ator’s manual carefully and make
sure you understand the instructions before using the
machine.
The machine is only designed for cutting branches and
twigs.
Always remove the battery to prevent the machine being
started by accident.
W
ork area safety
Keep work area clean and well lit.
Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes.
Keep children and bystanders away while
operating a power tool.
Distractions can cause you
to lose control.
Electrical saf
ety
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodified plugs and matching outlets will
reduce the risk of electric shock.
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase
the risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase
the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is
unaviodable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of
electric shock.
Personal safety
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A
moment of inattention while operating power tools
may result in serious personal injury.
Use personal protective equipment. Always wear
eye protection.
Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch
is in the OFF-position before connecting to a
power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your
finger on the switch or energising power tools that
have the switch on invites accidents.
Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and
balance at all times.
This enables better control of
the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or
long hair can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Use of dust
collection can reduce dust-related hazards.
The vibration emission during actual use of the power
tool can differ from the declared total value depending
on the ways in which the tool is used. Operators
should identify safety measures to protect themselves
that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger).
Power tool use and care
Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
!
WARNING! Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
IMPORTANT!
Save all warnings and instructions for future reference.
The term ”power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
H1154526-38,136 LiHD50,_1 v2.fm Page 7 Friday, February 10, 2012 3:20 PM
GENERAL SAFETY PRECAUTIONS
8 – English
Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools.
Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands
of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool´s operation. If damaged, have the power tool
repaired before use.
Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed.
Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Battery tool use and care
Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
Use power tools only with specifically designated
battery packs.
Use of any other battery packs may
create a risk of injury and fire.
When a battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may
cause burns or a fire.
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritations
or burns.
Service
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool
is maintained.
Hedge trimmer safety warnings -
Personal safety
Keep all parts of the body away from the cutter
blade. Do not remove cut material or hold material
to be cut when blades are moving. Make sure the
switch is off when clearing jammed material.
A
moment of inattention while operating the hedge
trimmer may result in serious personal injury.
Carry the hedge trimmer by the handle with the
cutter blade stopped. When transporting or
storing the hedge trimmer always fit the cutting
device cover.
Proper handling of the hedge trimmer
will reduce possible personal injury from the cutter
blades.
Hold the power tool by insulated gripping surface
only, because the cutter blade may contact hidden
wiring.
Cutter blades contacting a ”live” wire may
make exposed metal parts of the power tool ” live” and
could give the operator an electric shock.
IMPORTANT!
Always remove the battery before any maintenance on
the machine.
Children should be supervised to ensure that they do
not play with the appliance.
Store the machine out of reach of children. Never allow
children or other persons not trained in the use of the
machine and/or the battery to use or service it. Local
laws may regulate the age of the user.
Never use a machine that has been modified in any way
from its original specification.
Wear personal protective equipment. See instructions
under the ”Personal protective equipment” heading.
The operator of the machine must ensure, while
working, that no persons or animals come closer than
15 metres.
Never use the machine in bad weather, for instance in
fog, in rain, strong winds, intense cold, etc. Extremely
hot weather may cause overheating of the machine.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual. Some maintenance and service measures
must be carried out by trained and qualified specialists.
See instructions under the Maintenance heading.
Carry out an overall inspection of the machine before
use. See the maintenance schedule.
H1154526-38,136 LiHD50,_1 v2.fm Page 8 Friday, February 10, 2012 3:20 PM
GENERAL SAFETY PRECAUTIONS
English 9
Personal protective equipment
HEARING PROTECTION
Wear hearing protection that provides adequate noise
reduction.
EYE PROTECTION
Always wear approved eye protection. If you use a visor
then you must also wear approved protective goggles.
Approved protective goggles must comply with the ANSI
Z87.1 standard in the USA or EN 166 in EU countries.
GLOVES
Gloves should be worn when necessary, e.g. when fitting
cutting attachments.
BOOTS
Wear sturdy, non-slip boots or shoes.
CLOTHING
Wear clothes made of a strong fabric and avoid loose
clothing that can catch on twigs and branches. Always
wear heavy, long pants. Do not wear jewellery, shorts
sandals or go barefoot. Secure hair so it is above shoulder
level.
FIRST AID KIT
Always have a first aid kit nearby.
Battery and battery charger
This section describes the battery and battery charger
safety for your battery product.
Only use Husqvarna original batteries for Husqvarna
products and only charge them in an original battery
charger from Husqvarna. The batteries are software
encrypted.
!
WARNING! This machine produces an
electromagnetic field during operation.
This field may under some
circumstances interfere with active or
passive medical implants. To reduce the
risk of serious or fatal injury, we
recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this machine.
!
WARNING! Never allow children to use or
be in the vicinity of the machine. Since
the machine is easy to start, children
may be able to start it if they are not kept
under full surveillance. This can mean a
risk of serious personal injury. Therefore
disconnect the battery when the machine
is not under close supervision.
!
WARNING! Faulty blades can increase
the risk of accidents.
IMPORTANT!
Incorrect or careless use of a hedge trimmer can turn it
into a dangerous tool that can cause serious or even
fatal injury. It is extremely important that you read and
understand the contents of this operator's manual.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen.
Ask your dealer for help in choosing the right equipment.
!
WARNING! Listen out for warning signals
or shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
H1154526-38,136 LiHD50,_1 v2.fm Page 9 Friday, February 10, 2012 3:20 PM
GENERAL SAFETY PRECAUTIONS
10 – English
Battery safety
The rechargeable Husqvarna batteries, BLi, are
exclusively used as a power supply for the relevant
Husqvarna cordless appliances. To avoid injury, the
battery must not be used as a power source for other
devices.
Use the battery in surroundings where temperatures
are between -10
°C and 40 °C.
Do not expose the battery to microwaves or high
pressure.
Never clean the battery or the battery charger with
water. See also instructions under the Maintenance
heading.
Store the battery out of reach of children.
Protect the battery from rain and wet conditions.
Battery charger safety
Only use Chargers, Husqvarna QC, for charging the
Husqvarna replacement batteries, BLi.
Regularly check that the battery charger connection
wire is intact and that there are no cracks in it.
Never carry the battery charger using the cable and
never pull out the plug by pulling the cable.
Keep all cables and extension leads away from water,
oil and sharp edges. Make sure the cable is not
jammed in doors, fences or the like. Otherwise it can
cause the charger to become live.
Do not use:
a faulty or damaged battery charger or never use a
faulty, damaged or deformed battery.
!
WARNING! Protect the battery from
direct sunlight, heat or open flame. There
is a risk the battery may explode if it is
thrown into an open fire. There is a risk of
burns and/or chemical burns.
!
WARNING! Avoid all skin contact with
battery acid. Battery acid may cause skin
irritation, burns or corrosive injuries. If
you get acid in your eyes, do not rub but
flush your eyes with plenty of water for at
least 15 minutes. See a doctor. You must
wash any exposed skin with copious
amounts of water and soap in case of
incidental contact.
!
WARNING! Never connect the battery
terminal to keys, coins, screws or other
metal as this may short-circuit the
battery. Never insert objects into the
battery's air vents.
Unused batteries must be kept away from
metal objects such as nails, coins,
jewellery. Do not try to disassemble or
crush the battery
Li-ion
Li-ion
!
WARNING! Minimise the risk of electric
shock or short circuit as follows:
Never insert any object into the charger’s
cooling slots.
Do not try to dismantle the battery
charger.
Never connect the charger terminals to
metal objects as this can short circuit the
battery charger.
Use approved and intact wall sockets.
!
WARNING! Do not use the battery
charger close to corrosive or flammable
materials. Do not cover the battery
charger. Pull out the plug to the battery
charger in the event of smoke or fire.
Remember the risk of fire.
Li-ion
Li-ion
H1154526-38,136 LiHD50,_1 v2.fm Page 10 Friday, February 10, 2012 3:20 PM
GENERAL SAFETY PRECAUTIONS
English 11
Do not charge:
non-rechargeable batteries in the battery charger or
use them in the machine.
the battery charger to charge the battery outdoors.
the battery in the rain or in wet conditions.
the battery in direct sunlight.
Use the battery charger only when the surrounding
temperature is between 5
°C and 40 °C. Use the charger
in an environment which is well ventilated, dry and free
from dust.
Machines safety equipment
This section describes the machines safety equipment,
its purpose, and how checks and maintenance should be
carried out to ensure that it operates correctly. See the
”What is what?” section to locate where this equipment is
positioned on your machine.
The life span or the runtime of the machine can be
reduced and the risk of accidents can increase if machine
maintenance is not carried out correctly and if service
and/or repairs are not carried out professionally. If you
need further information please contact your nearest
service workshop.
Control panel
Make sure the machine is switched on or off when the
activate/deactivate button (1) is pressed and held (>1
sec.). The green LED (2) is lit or turned off.
Flashing warning symbol (3) and green LED (2) is lit could
indicate that:
it is not possible to apply full power and, at the same
time, activate the machine. Release the power trigger
and the machine is active.
the machine is blocked. Deactivate the machine.
Remove the battery from the machine. Remove the
twigs, branches or other materials that are jammed in
the blades.
the machine is overloaded due to heavy trimming.
Release the power trigger and the machine is active.
If the warning symbol (3) flashes, it indicates that the
machine is too hot and the machine deactivates. When
the machine is restored to normal temperature it is again
ready to run and you can activate the machine.
Solid red warning light (3) indicates service.
Power trigger lockout
The power trigger is designed to prevent accidental
operation. It is necessary to press both the power trigger
lockout and the power trigger. The order actuation power
trigger lockout and power trigger doesn’t matter. When
you release the handle, the power trigger and the power
trigger lockout both move back to their original positions.
This movement is operated by independent springs. This
arrangement means that the power trigger is
automatically locked at no operation state.
IMPORTANT!
All servicing and repair work on the machine requires
special training. This is especially true of the machine
s
safety equipment. If your machine fails any of the
checks described below you must contact your service
agent. When you buy any of our products we guarantee
the availability of professional repairs and service. If the
retailer who sells your machine is not a servicing dealer,
ask him for the address of your nearest service agent.
!
WARNING! Never use a machine with
faulty safety equipment. The machine's
safety equipment must be checked and
maintained as described in this section.
If your machine fails any of these checks
contact your service agent to get it
repaired.
(2)
(1)
(3)
H1154526-38,136 LiHD50,_1 v2.fm Page 11 Friday, February 10, 2012 3:20 PM
GENERAL SAFETY PRECAUTIONS
12 – English
Turn on the machine. Press the power trigger lockout on
the front handle.
Press the power trigger forward to release the power
trigger.
Then press the power trigger up to apply full power.
Release the power trigger and check thereby the free
back movement of the power trigger. The cutting unit must
stop within 1 second.
Restart the machine and release the power trigger
lockout on the front handle. Check that the power trigger
lockout returns to its original position when you release it.
The cutting unit must stop within 1 second.
Hand guard
The hand guard prevents hands from coming into contact
with the moving blades, for example, if the operator loses
grip on the front handle.
Check that the hand guard is fitted correctly. Check that
the hand guard is undamaged.
Blade and blade guard
The outer part of the blades (1) is shaped as blade
guards.
Check that the blade guard is not damaged or distorted.
Replace the cutting unit if it is bent or damaged.
1
2
Li-ion
Li-ion
Li-ion
Li-ion
H1154526-38,136 LiHD50,_1 v2.fm Page 12 Friday, February 10, 2012 3:20 PM
BATTERY HANDLING
English 13
Battery
The display shows the battery capacity and if there are
any problems with the battery. The battery capacity is
displayed for 5 seconds after the machine is switched off
or the battery indicator button is pressed. The warning
symbol on the battery is lit when an error has occurred.
See fault codes.
Battery charger
Connect the battery charger
Connect the battery charger to the voltage and
frequency specified on the rating plate. Put the
electric plug in the wall socket. The LED on the battery
charger flashes green once.
The battery will not be charged if the battery
temperature is over 50
°C. In that case the battery
charger will actively cool down the battery.
Connect the battery to the battery charger
Regularly check that the battery charger and the battery
are intact. See also instructions under the Maintenance
heading.
The battery must be charged before using it the first time.
The battery is only 30% charged when delivered.
Put the battery in the battery charger. Make sure that
the battery is connected to the battery charger.
The green charging light is lit when the battery is
connected to the battery charger.
When all LEDs are lit the battery is fully charged.
Pull out the plug. Never jerk the power supply cable to
disconnect it from the wall socket.
Remove the battery from the battery charger.
Charging status
Lithium-ion batteries can be charged whatever their
charge level. The charging process can be cancelled or
started whatever the battery's charge level. The battery is
not damaged. A fully charged battery will not lose its
charge even when the battery is left in the charger.
The battery will not be charged if the battery temperature
is over 50
°C.
LED lights Battery
All LEDs are lit Fully charged (75-100%).
LED 1, LED 2, LED 3 are
lit.
The battery is 50%-75%
charged.
LED 1, LED 2 are lit.
The battery is 25%-50%
charged.
LED 1 is lit.
The battery is 0%-25%
charged.
LED 1 flashes
The battery is empty.
Charge the battery.
!
WARNING! Risk of electric shock and
short circuiting. Use approved and intact
wall sockets. Make sure that the cable is
not damaged. Replace cable if it appears
to be damaged in any way.
LED display Charging status
LED 1 flashes
The battery is 0%-
25% charged.
LED 1 is lit, LED 2 flashes.
The battery is 25%-
50% charged.
LED 1, LED 2 are lit, LED 3
flashes
The battery is 50%-
75% charged.
LED 1, LED 2, LED 3 are lit,
LED 4 flashes
Battery is 75%-100%
charged
LED 1, LED 2, LED 3, LED 4
are lit.
When all the LEDs
are lit on the battery,
it is fully charged.
H1154526-38,136 LiHD50,_1 v2.fm Page 13 Friday, February 10, 2012 3:20 PM
BATTERY HANDLING
14 – English
Transport and storage
Secure the machine during transport.
Always remove the battery for storage or transport.
Store the battery and the battery charger in a dry,
moisture-free and frost-free space.
To prevent accidents, ensure that your battery is not
connected to the machine when stored.
Do not store the battery in places where static
electricity can occur. Never store the battery in a metal
box.
Store the battery and the battery charger where the
temperature is between 5
°C and 45 °C and never in
direct sunlight.
Store the battery charger only in an enclosed and dry
space.
Be sure to store the battery separate from the battery
charger. Store the equipment in a lockable area so
that it is out of reach of children and unauthorized
persons.
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
Disposal of the battery, battery
charger and machine
Symbols on the product or its packaging indicate that this
product cannot be handled as domestic waste. It must
instead be submitted to an appropriate recycling station
for the recovery of electrical and electronic equipment.
By ensuring that this product is taken care of correctly,
you can help to counteract the potential negative impact
on the environment and people that can otherwise result
through the incorrect waste management of this product.
For more detailed information about recycling this
product, contact your municipality, your domestic waste
service or the shop from where you purchased the
product.
Li-ion
Li-ion
Li-ion
H1154526-38,136 LiHD50,_1 v2.fm Page 14 Friday, February 10, 2012 3:20 PM
STARTING AND STOPPING
English 15
Check before starting
Inspect the working area. Remove any objects that
could be thrown out.
Check the cutting attachment. Never use blades that
are dull, cracked or damaged.
Check that the machine is in perfect working order.
Check that all nuts and screws are tight.
Only use the machine for the purpose it was intended
for.
Make sure that the handle and safety features are in
good working order. Never use a machine that lacks a
part or has been modified outside its specifications.
Gloves should be worn when necessary.
All covers must be correctly fitted and undamaged
before you start the machine.
Connect battery to the machine
Make sure to use fully charged batteries. Use only a
Husqvarna original battery in your machine. See technical
data.
Insert the battery in the machine. The battery should
slide easily into the battery holder on the machine. If
the battery does not slide in easily, it is not being
inserted correctly. The battery will lock itself into place
when you hear a click. Make sure the battery is fitted
correctly to the machine.
Starting and stopping
Starting
Turn on the machine. Press and hold the start button (>1
sec.) until the green LED is lit.
Press the power trigger lockout up. It is placed on the front
handle.
Press the power trigger forward to release the power
trigger.
Then press the power trigger up to apply full power.
!
WARNING! Make sure no unauthorised
persons are in the working area.
Otherwise there is a risk of serious
personal injury. The safety distance is 15
metres.
Li-ion
Li-ion
1
2
H1154526-38,136 LiHD50,_1 v2.fm Page 15 Friday, February 10, 2012 3:20 PM
STARTING AND STOPPING
16 – English
Stopping
Stop the machine by releasing the power trigger or the
power trigger lockout and deactivate the machine.
Remove the battery from the machine by pressing the two
release buttons and pulling out the battery.
IMPORTANT! Always remove the battery to prevent the
machine being started by accident.
H1154526-38,136 LiHD50,_1 v2.fm Page 16 Friday, February 10, 2012 3:20 PM
WORKING TECHNIQUES
English 17
General working instructions
Basic safety rules
Never allow children to use or be in the vicinity of the
machine.
Observe your surroundings and make sure that there
is no risk of people or animals coming into contact
with the cutting equipment.
Never allow anyone else to use the machine without
first ensuring that they have understood the contents
of the operator's manual.
Inspect the working area. Remove any objects that
could be thrown out.
Never work from a ladder, stool or any other raised
position that is not fully secured.
CAUTION! Do not use the machine unless you are
able to call for help in the event of an accident. Ensure
that no-one comes closer than 15 metres while you
are working.
Never use the machine in bad weather, for instance in
fog, in rain, strong winds, intense cold, etc.
If any foreign object is hit or if vibrations occur stop the
machine immediately. Remove the battery from the
machine and check that the machine is not damaged.
SavE mode
The machine is equipped with a battery saving function
(SavE). Activate the function by pressing the SavE button.
A green LED will light to indicate that the function is on.
Automatic switch off functionality
The machine is equipped with a shutdown feature that
deactivates the machine if not used. The green LED and
the machine will switch off after 1 minute.
Safety instructions while working
Do not overreach. Keep proper footing and balance at
all times.
Turn off the machine when it has to be moved.
Never put the machine down without turning it off first
and always remove the battery.
IMPORTANT!
This section takes up the basic safety precautions for
working with a hedge trimmer.
If you encounter a situation where you are uncertain
how to proceed you should ask an expert. Contact your
dealer or your service workshop.
Avoid all usage which you consider to be beyond your
capability.
!
WARNING! The machine can cause
serious personal injury. Read the safety
instructions carefully. Learn how to use
the machine.
!
WARNING! Cutting tool. Do not touch the
tool without first switching off the
engine. Always remove the battery
before any maintenance on the machine.
!
WARNING! Watch out for thrown objects.
Always wear approved eye protection.
Never lean over the cutting attachment
guard. Stones, rubbish, etc. can be
thrown up into the eyes causing
blindness or serious injury.
Keep unauthorised persons at a
distance. Children, animals, onlookers
and helpers should be kept outside the
safety zone of 15 metres. Stop the
machine immediately if anyone
approaches. Never swing the machine
around without first checking behind you
to make sure no-one is within the safety
zone.
H1154526-38,136 LiHD50,_1 v2.fm Page 17 Friday, February 10, 2012 3:20 PM
WORKING TECHNIQUES
18 – English
Always use both hands to hold the machine. Hold the
machine at the side of your body.
Make sure that no clothes or parts of the body come
in contact with the cutting equipment when it is
activated.
When the motor is switched off, keep your hands and
feet away from the cutting attachment until it has
stopped completely.
Watch out for stumps of branches that can be thrown
out during cutting. Do not cut too close to the ground.
Stones and other objects can be thrown out.
Check the working area for foreign objects such as
electricity cables, insects and animals, etc, or other
objects that could damage the cutting attachment,
such as metal items.
If anything jams in the blades while you are working,
switch off the motor and wait until it has stopped
completely before cleaning the blades. Remove the
battery from the machine.
Never leave the machine unsupervised with the motor
running.
Safety instructions after completing work
The transport guard should always be fitted to the
cutting attachment when the machine is not in use.
Make sure the cutting attachment has stopped before
cleaning, carrying out repairs or an inspection.
Remove the battery from the machine.
Always wear heavy-duty gloves when repairing the
cutting attachment. The blades are very sharp and
can easily cause cuts.
Store the machine out of reach of children.
Use only original spare parts for repairs.
Basic working techniques
Work with a swinging action from the bottom upwards
when trimming sides.
When trimming a hedge the engine should always
face away from the hedge.
Hold the machine as close to your body as possible to
get the best balance.
Make sure that the tip does not touch the ground.
Do not rush the work, but work steadily until all the
branches have been cut back cleanly.
Li-ion
Li-ion
H1154526-38,136 LiHD50,_1 v2.fm Page 18 Friday, February 10, 2012 3:20 PM
MAINTENANCE
English 19
Inspection and maintenance
All servicing and repair work on the machine requires
special training. This is especially true of the machine
s
safety equipment. If your machine fails any of the checks
described below you must contact your service agent.
When you buy any of our products we guarantee the
availability of professional repairs and service. If the
retailer who sells your machine is not a servicing dealer,
ask him for the address of your nearest service agent.
Only use original spare parts.
Regularly check that the battery charger and the battery
are intact.
Cleaning
Clean the machine after use.
Make sure the battery and battery charger are clean and
that the terminals on the battery and the battery charger
are always clean and dry before the battery is placed in
the battery charger.
Keep the battery guide tracks clean. Clean plastic parts
with a clean and dry cloth.
Cleaning and lubrication
Clean any resin and plant residue from the blades using
cleaning agent before and after using the machine.
Check that the blade edges are not damaged or
deformed. File away any burrs. Check that the blades
move freely.
Lubricate the blade with special oil before long periods of
storage.
!
WARNING! Always remove the battery
before any maintenance on the machine.
IMPORTANT! Never clean the battery or the battery
charger with water.
Strong cleaning agents can damage the plastic.
Li-ion
Li-ion
H1154526-38,136 LiHD50,_1 v2.fm Page 19 Friday, February 10, 2012 3:20 PM
20 – English
MAINTENANCE
Troubleshooting schedule
Control panel
Troubleshooting takes place from the control panel.
Battery and battery charger
Troubleshooting the battery and/or the battery charger during charging.
LED display Possible faults Possible action
Error LED flashes.
Overload.
The cutting attachment is
jammed. Release the cutting
attachment.
Temperature deviation.
Allow the machine to cool
down.
The power trigger and the
activate button are pressed
at the same time.
Release the power trigger
and the machine is active.
Error LED is lit with red light. Non repairable fault. Contact your service agent.
LED display Possible faults Possible action
Error LED flashing.
Temperature
deviation.
Use the battery in surroundings
where temperatures are between -
10
°C and 40 °C.
Over voltage.
Check that the mains voltage
corresponds with that stated on the
rating plate on the machine.
Remove the battery from the battery
charger.
Error LED is lit.
Cell difference too
much (1V).
Contact your service agent.
H1154526-38,136 LiHD50,_1 v2.fm Page 20 Friday, February 10, 2012 3:20 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246

Husqvarna 136 LiHD50 Le manuel du propriétaire

Catégorie
Taille-haies électriques
Taper
Le manuel du propriétaire