Panasonic PV27DF62K Mode d'emploi

Marque: Panasonic

Modèle: PV27DF62K

Catégorie: Lecteurs DVD

Taper: Mode d'emploi

Please read these instructions carefully before attempting to connect,

operate, or adjust this product. Please save this manual.

LSQT0587A

DVD Combination

Operating Instructions

Models No. PV-27DF62-K

• Initial Setup and Connection Procedures are on pages 10 to 15.

As an ENERGY STAR Partner, Panasonic has determined that this product

or product model meets the ENERGY STAR guidelines for energy efficiency.

TV Operation

Advanced Operation

DVD Operation

For Your InformationInitial Setup

27DF62-K(E) (P01).p65 2002/04/15, 18:391

Important Safeguards and Precautions

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from power source indicated on unit

or in this manual. If uncertain, have your Electric

Utility Service Company or Video Products Dealer

verify your home power source.

2 POWER CORD PLUG

For safety, this unit has a polarized type plug (one

wide blade), or a three-wire grounding type plug.

Always hold the plug firmly and make sure your

hands are dry when plugging in or unplugging the

AC power cord. Regularly remove dust, dirt, etc.

on the plug.

POLARIZED PLUG CAUTION:

The plug fits into outlet only one way. If it cannot be

fully inserted, try reversing it. If it still will not fit, have

an electrician install the proper wall outlet. Do not

tamper with the plug.

GROUNDING PLUG CAUTION:

The plug requires a three-hole grounding outlet.

If necessary, have an electrician install the proper

outlet. Do not tamper with the plug.

3 POWER CORD

To avoid unit malfunction, and to protect against

electrical shock, fire or personal injury:

- Keep power cord away from heating appliances

and walking traffic. Do not rest heavy objects on,

or roll such objects over the power cord.

- Do not tamper with the cord in any way.

- An extension cord should have the same type

plug (polarized or grounding) and must be

securely connected.

- Overloaded wall outlets or extension cords are

fire hazards.

- Frayed cords, damaged plugs, and damaged or

cracked wire insulation are hazardous and should

be replaced by a qualified electrician.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat

generated during operation. If blocked, heat

build-up may result in a fire hazard or heat

damage to discs.

For your protection:

a. Never cover ventilation slots while unit is ON,

or operate unit while placed on a bed, sofa,

rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless properly ventilated.

AVOID EXTREMELY HOT LOCATIONS OR

SUDDEN TEMPERATURE CHANGES

Do not place unit over or near a heater or radiator,

in direct sunlight, inside closed vehicles,

in high temperature [over 95 °F (35 °C)], or in over

75% humidity. If unit is suddenly moved from a

cold place to a warm one, moisture may

condense in unit and on the tape causing

damage. Never subject unit to vibration, impact,

or place it so that the surface is tilted as internal

parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Never place unit on support or stand that is not

firm, level, and adequately strong. The unit could

fall causing serious injury to a child

or adult and damage to the unit.

• Move any appliance and cart

combination with care.

Quick stops, excessive force, and

uneven surfaces may cause objects to overturn.

• Carefully follow all operating instructions.

USING THE UNIT

Before unit is brought out of storage or moved to a new location,

refer again to the INSTALLATION section of these safeguards.

1 KEEP UNIT WELL AWAY FROM WATER OR

MOISTURE, such as vases, sinks, tubs, etc.

2 IF EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT, unplug unit and have it inspected

by a qualified service technician before use.

3 ELECTRICAL STORMS

During a lightning storm, or before leaving unit unused for

extended periods of time, disconnect all equipment from

the power source as well as the antenna and cable system.

4 WHEN UNIT IS PLUGGED IN

• DO NOT OPERATE IF:

- liquid has spilled into unit.

- unit was dropped or otherwise damaged.

- unit emits smoke, odours, or noises.

Immediately unplug unit, and have it inspected by a

service technician to avoid potential fire and shock hazards.

•

Never drop or push any object through openings in unit.

Touching internal parts may cause electric shock or fire hazard.

Do not put any foreign object on the tray.

• Keep magnetic objects, such as speakers, away from

unit to avoid electrical interference.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer

to avoid risk of fire, shock, or other hazards.

6 CLEANING UNIT

Unplug unit. Use a clean, dry, chemically untreated cloth to

gently remove dust or debris. DO NOT USE cleaning fluids,

aerosols, or forced air that could over-spray, or seep into unit and

cause electrical shock. Any substance, such as wax, adhesive

tape, etc. may mar the cabinet surface. Exposure to greasy,

humid, or dusty areas may adversely affect internal parts.

READ AND RETAIN ALL SAFETY AND

OPERATING INSTRUCTIONS. HEED ALL

WARNINGS IN THE MANUAL AND ON UNIT

SERVICE

1 DO NOT SERVICE PRODUCT YOURSELF

If, after carefully following detailed operating instructions, the

unit does not operate properly, do not attempt to open or

remove covers, or make any adjustments not described in the

manual. Unplug unit and contact a qualified service technician.

2 REPLACEMENT OF PARTS

Make sure the service technician uses only parts specified

by the manufacturer, or have equal safety characteristics

as original parts. The use of unauthorized substitutes may

result in fire, electric shock, or other hazards.

3 SAFETY CHECK AFTER SERVICING

After unit is serviced or repaired, request that a thorough safety

check be done as described in the manufacturer’s service

literature to ensure video unit is in safe operating condition.

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC

- NATIONAL ELECTRICAL CODE

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

An outside antenna or cable system must be properly

grounded to provide some protection

against built up static charges and

voltage. Part 1 of the

Canadian Electrical Code, in

U.S.A. Section 810 of the

National Electrical Code.

ANSI/NFPA 70 provides

information regarding proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE

POWER LINES OR CIRCUITS

Locate an outside antenna system well away from power

lines and electric light or power circuits so it will never

touch these power sources should it ever fall. When

installing antenna, absolutely never touch power lines,

circuits or other power sources as this could be fatal.

27DF62-K(E) (P02-3).p65 2002/04/15, 18:392

Safety Precautions

WARNING:

To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert.

This television receiver provides display of television closed captioning.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.

HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH

COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF

DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS

INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT

PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY

AND OTHER OPENINGS TO LOOK INSIDE THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE

UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION WHEN

OPEN. DO NOT STARE

INTO BEAM.

(Inside of product)

This symbol warns the user that uninsulated voltage

within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any

kind of contact with any inside part of this unit.

This symbol alerts the user that important literature

concerning the operation and maintenance of this unit

has been included. Therefore, it should be read carefully

in order to avoid any problems.

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

Region Management Information

Region Management Information: This unit is designed and

manufactured to respond to the Region Management

Information that is recorded on a DVD disc. If the Region

number described on the DVD disc does not correspond to

the Region number of this unit, this unit cannot play this disc.

The Region number

for this unit is 1.

This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead.

Disposal of these materials may be regulated in your community due to environmental

considerations. For disposal or recycling information please contact your local authorities, or the

Electronics Industries Alliance: <http://

www.eiae.org.>

27DF62-K(E) (P02-3).p65 2002/04/15, 18:393

Before Using

Congratulations

on your purchase of one of the most

sophisticated and reliable products on the

market today. Used properly, it will bring you

and your family years of enjoyment. Please

fill in the information below. The serial number

is on the tag located on the back of your unit.

Date of Purchase

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No.

PV-27DF62-K

Serial No.

Remote Control

LSSQ0346

Batteries 2 “AA”

Accessories

LIGHT

TITLE MENU

DISPLAY

ADD/DLT

PAUSE

DSS

CABLE

SKIP

PLAY

STOP

SLOW/SEARCH

SUB TITLE

ANGLE

ZOOM

AUDIO

OPEN/CLOSE

CLEAR

ENTER

ACTION RETURN

D V DFM/TV

S E T

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Loading the Batteries

Apparatus Claims of U.S. Patent Nos.

4,631,603, 4,577,216, and 4,819,098,

licensed for limited viewing uses only.

This product incorporates copyright protection

technology that is protected by method claims

of certain U.S. Patents and other intellectual

property rights owned by Macrovision

Corporation and other rights owners. Use of

this copyright protection technology must be

authorized by Macrovision Corporation, and is

intended for home and other limited viewing

uses only unless otherwise authorized by

Macrovision Corporation. Reverse

engineering or disassembly is prohibited.

Features for a Quality Picture

Pure Flat Picture Tube

This unit is equipped with pure flat Picture Tube.

27DF62-K(E) (P04 Before).p65 2002/04/15, 18:394

Table of Contents

Initial Setup

Important Safeguards and Precautions / Safety Precautions ....... 2 ~ 3

Before Using ........................................................................................ 4

Information (Unit, Disc) .................................................................... 6, 7

Location of Controls ........................................................................ 8, 9

Connections / Initial Setup .......................................................... 10, 11

Reset Language, Channels, Clock, Time Zone Adjust ............... 12, 13

Audio Connections ...................................................................... 14, 15

TV Operation

TV Operation ..................................................................................... 18

MTS Broadcast / TV Stereo System .................................................. 19

Closed Caption System ............................................................... 20, 21

TV Timer Features ............................................................................. 22

On-Screen Display (OSD) ................................................................. 23

FM Radio ..................................................................................... 24, 25

Advanced Operation

Cable Box Universal Remote Control Feature ........................... 26, 27

Special Features ......................................................................... 28, 29

V-Chip Control Feature ............................................................. 30 ~ 35

Video / Audio Menu ........................................................................... 36

Video / Audio Adjustment .................................................................. 37

Disc Operation ........................................................................... 38 ~ 42

DVD Operation using On-Screen Displays .............................. 43 ~ 45

MP3 Playback Operation .................................................................. 46

DVD Lock Feature ............................................................................. 47

DVD

For Your Information

Before Requesting Service ......................................................... 52, 53

Warning and Instruction Displays ..................................................... 53

Limited Warranty ............................................................................... 54

Servicentre List .................................................................................. 55

Index ............................................................................................ 56, 57

Settings for DVD Operation ....................................................... 48 ~ 50

Language Code List .......................................................................... 51

DVD

DVD Operation

Basic DVD Operation .................................................................. 16, 17

DVD

TV Operation

Advanced Operation

DVD Operation

For Your InformationInitial Setup

27DF62-K(E) (P05 contents).p65 2002/04/15, 18:395

Information (Unit, Disc)

Specifications

Display

Picture Tube: 27 inch diagonal pure flat Picture Tube

Tuner

Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69

CABLE Channels: Midband A through I (14 ~ 22)

Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64)

Lowband A-5 ~ A-1 (95 ~ 99)

Special CABLE channel 5A (01)

Ultraband 65 ~ 94, 100 ~ 125

FM Radio

Band range: 87.5 ~ 108.1 MHz

General

Power Source: 120V AC, 60 Hz

Power Consumption: Power On

Approx. 146 watts

Power Off

Approx. 3.5 watts

Television System: EIA Standard NTSC colour

Speaker: 2 pieces (5.0W x 2)

Operating Temperature: 5 °C ~ 35 °C (41 °F ~ 95 °F)

Operating Humidity: 10% ~ 75%

Weight: 47 kg (103.4 lbs.)

Dimensions: 760 (W) x 651 (H) x 503 (D) mm

29-15/16” (W) x 25-5/8” (H) x 19-13/16” (D)

Discs played

(1)DVD-VIDEO disc 5” (12 cm) single-sided, single-layer

5” (12 cm) single-sided, double-layer

5” (12 cm) double-sided, double-layer

(one layer per side)

3” (8 cm) single-sided, single-layer

3” (8 cm) single-sided, double-layer

3” (8 cm) double-sided, double-layer

(one layer per side)

(2) Compact disc 5” (12 cm) disc

(CD-DA, VIDEO CD) 3” (8 cm) disc

Digital audio output: Optical digital output:

Optical connector

Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)

Laser power: CLASS II

Note : Designs and specifications are subject to change without notice.

If the disc cannot be removed...

First, unplug unit.

Then, prepare a rigid wire (e.g. an extended paper clip)

and, applying moderate force, insert it straight into the

hole at the base of the tray. The tray will eject a little.

Then, pull the tray all the way out and remove the disc.

27DF62-K(E) (P06-7 Information).p65 2002/04/15, 18:396

Definition of Terms

Angle

Some DVD discs feature scenes simultaneously shot

from different angles. The ANGLE button can be

used to view the scene from different angles.

(ANGLE Indicator lights up on the unit when a

scene recorded at different angles is detected.)

Chapter Number

Titles are subdivided into numbered sections. You can

quickly search for a favourite scene using these numbers.

DVD

A high-density optical disc on which high-quality

pictures and sound have been digitally recorded.

DVD incorporates new video compression

technology (MPEG II) and high-density recording

technology which allow entire movies to be

recorded with incredible playback quality.

Playback Control

With Video CD (version 2.0), scenes or information

may be selected for viewing or listening from an

interactive menu that appears on the TV screen.

Subtitles

Written dialogue which appears at the bottom of the screen.

Time Number

The elapsed play time from the start of a disc or title.

Use to quickly find scenes. (May not work with some discs.)

Title Number

For DVD discs with two or more titles, the title is

numbered as title 1, title 2, etc.

Track Number

Numbers assigned to tracks on Video CDs and CDs

to allow specific tracks to be quickly located.

Video CD

CD containing picture and sound with same quality

level as video tape. This unit also supports Video

CDs with playback control (version 2.0).

If disc is brought from a cold to a

warm environment, moisture may form

on the disc

Wipe away moisture with a soft, dry, lint-free

cloth before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Disc Handling

Disc formats supported by this unit

The unit can play back discs bearing any of the

following marks:

Discs which cannot be played with this unit

• DVD with Region No. other than “1” or “ALL”

• DVD of PAL system

• DVD-ROM • DVD-R/DVD-RAM

• DVD-R/DVD-RAM • CD-ROM

• CDV • CD-G

• Do not try to play a Photo CD.

DVD

3” (8 cm) disc / 5” (12 cm) disc

Video CD

3” (8 cm) disc / 5” (12 cm) disc

is a registered trademark.

Handling precautions

• Only hold disc by edges as shown.

Fingerprints, dirt, and scratches

can cause skipping and

distortion.

• Do not write on label

side of disc.

• Never use record

cleaning sprays, benzine, thinner, static

electricity prevention liquids, or any other

solvent.

• Be careful not to drop

or bend disc.

• Do not place more

than 1 disc on disc

tray.

• Do not try to close disc tray when disc is

not properly placed.

• Always store discs in

their proper cases

when not in use.

To clean disc surface

With a soft, damp (water only) cloth, gently

wipe from the centre hole to the outer edge as

shown below. (Wiping in a circular pattern will

scratch the surface.)

Disc tray

Disc

Initial Setup

27DF62-K(E) (P06-7 Information).p65 2002/04/15, 18:397

Location of Controls

LIGHT

TITLE MENU

DISPLAY

ADD/DLT

PAUSE

DSS

CABLE

SKIP

PLAY

STOP

SLOW/SEARCH

VOL

SUB TITLE

ANGLE

ZOOM

AUDIO

OPEN/CLOSE

CLEAR

ENTER

ACTION RETURN

D V DFM/TV

S E T

Remote Control Buttons (Light Tower

Illuminated Remote Control)

• When LIGHT is pressed, (FM/TV, DVD, DSS/CABLE, CH UP/DOWN, VOL+/-) buttons will light for 5

seconds for easy location. If no button is pressed in 5 seconds the light goes out to conserve the batteries.

DVD

Sets to DVD mode.

LIGHT

See below.

DSS/CABLE

Sets the remote to control some

basic DDS or Cable box functions.

TIMER

Sets ON TIMER or SLEEP TIMER.

VOLUME UP/DOWN

Adjusts volume.

RAPID TUNE

Displays the last channel

you were watching.

ADD/DELETE/CLEAR

Adds or deletes a channel.

Cancels an item on the screen.

SUB TITLE

Selects a different subtitle language.

DISPLAY/ENTER

Displays the TV status and clock.

In DVD mode, displays disc and

unit information.

In DSS or CABLE mode, it may be

necessary after channel selection.

Displays DVD menu.

RETURN

Returns to Menu screen.

SKIP

Skips one chapter or track.

Goes to next menu screen.

ZOOM

Enlarges specific portions of picture.

STOP

Stops playback.

SLOW/SEARCH

Slow motion picture in Still mode.

Forward/Reverse rapid scene

search in Play mode.

OPEN/CLOSE

Opens or closes the disc tray.

POWER

Turns the unit on or off.

FM/TV

Sets to TV mode.

Receives FM radio signal.

MUTE

Mutes the sound instantly.

CHANNEL UP/DOWN

Selects a channel.

SURROUND

Creates a deeper, 3-D sound effect.

NUMBER Keys

Selects a channel directly.

ANGLE

Selects the desired angle

in DVD mode.

AUDIO

Selects the desired audio mode.

TITLE

Selects the desired title by number

on some DVDs.

SELECT

Controls navigation around

on-screen menu.

ACTION

Displays Main Menu.

SET

Sets a selected menu.

SKIP

Skips back one chapter or track.

Goes to previous menu screen.

PAUSE

Pauses picture in Play mode and

frame advance picture in Still mode.

PLAY

Begins playback.

Note

27DF62-K(E) (P08-9 Location).p65 2002/04/15, 18:398

Front View of the Unit and Indicators

PHONES

Connect an earphone

or headphones.

AUDIO/VIDEO IN Connector 2

(LINE 2)

Connect from other component.

S-VIDEO IN Connector

Connect from other component with S-Video.

POWER (See previous page.)

VOLUME UP/DOWN (See previous page.)

CHANNEL UP/DOWN (See previous page.)

PAUSE (See previous page.)

STOP (See previous page.)

SKIP | (See previous page.)

SLEEP TIMER Indicator

Lights when the

Sleep-Timer is set.

ON TIMER Indicator

Lights when the On-Timer is set.

ANGLE Indicator

Lights when a scene recorded

at a different angle is detected.

Remote Sensor

Aim the remote to this point.

OPEN/CLOSE (See previous page.)

SKIP | (See previous page.)

PLAY (See previous page.)

Disc Tray

Insert a disc to this tray.

Rear View of the unit

AC Power Plug

When plugged into an AC outlet, the unit consumes

3.5 W of electric power in OFF condition.

Optical Digital Audio Output Connector

Connect to a Dolby Digital decoder or dts decoder.

For details, see page 15.

AUDIO/VIDEO OUT Connector

Connect to other component.

VHF/UHF Antenna Input Terminal

In from your Antenna or Cable.

S-VIDEO IN Connector

Connect from other component with S-Video.

AUDIO/VIDEO IN Connector 1 (LINE 1)

Connect from other component.

Initial Setup

27DF62-K(E) (P08-9 Location).p65 2002/04/15, 18:399

VHF/UHF

Initial Setup (Ready to Play)

For ANT./Cable

Connect the cable from

Antenna/Cable to the VHF/

UHF terminal on the unit.

For DSS/Cable Box

Connect the OUT jack on

your cable box to the VHF/

UHF terminal on the unit

with a RF cable.

UNIT

IN from

ANT./CABLE

VHF/UHF

WARNING:

Overtightening "Nut type" RF

coaxial cables may damage jacks.

Finger tighten only.

Connecting

Plug the unit power cord into

an AC wall outlet.

• If you use a cable box, turn it on and set it

to the Public Broadcasting Service (PBS)

channel in your time zone. If you use a

DSS receiver, it must be turned off.

Initial Setup (Ready to Play)

Please make all cable or antenna connections before powering on.

Press POWER* on the remote or unit.

The unit comes on and auto channel

and clock set starts.

CH AUTO SET PROCEEDING

Settings are made automatically.

When setup is done, this screen

appears.

PROCEEDING

AUTO CLOCK SET

CANCEL : PRESS STOP KEY

If AUTO CLOCK SET IS

INCOMPLETE screen appears, set

the clock using MANUAL CLOCK

SET procedure on next page.

PLEASE

SET

CLOCK BY

ESS

ACT

KEY

UTO

OCK SET

I S I NCO

ETE

2002

DST

UTO

OCK SET

ETED

SETT

VHF/UHF

Cable TV

Converter Box

IN from

ANT./CABLE

27DF62-K(E) (P10-11 Initial Setup).p65 2002/04/15, 18:3910

Initial Setup

Important: If a remote control button does not work when pressed, press the FM/TV button on the

remote and try the button again.

Note to CABLE System Installer

This reminder is provided to call the

CABLE (Cable TV) System Installers

attention to Article 820-40 of the NEC

that provides guidelines for proper

grounding and, in particular, specifies

that the cable ground shall be

connected to the grounding system of

the building, as close to the point of

cable entry as practical.

Unit auto adjusts clock for DST (Daylight

Saving Time.)

■■

■ Spring (First Sunday in April)

DST : ON ➛Sets clock ahead one hour.

■■

■ Autumn (Last Sunday in October)

DST : ON ➛Turns clock back one hour.

• If your area does not observe Daylight

Saving Time, select DST:OFF.

DST (Daylight Saving Time)

Manual Clock Set

If AUTO CLOCK SET was incomplete, manually

set the clock as follows.

Press ACTION on

the Remote to

display SET CLOCK

Menu screen.

SET

END

ACT

SET

DST

Press to

select the month

and press SET to

set. In the same

manner, select and

set the date, year,

time, and DST.

Press ACTION twice to start CLOCK

and exit.3

Reset all unit Memory Functions

When moving unit to a new location, or if a mistake was

made in the Initial Setup section.

Turn the unit Power on.

Press and hold both PLAY and | on

the unit for more than 5 seconds.

• The power will shut off.

LIGHT

TITLE MENU

DISPLAY

ADD/DLT

PAUSE

DSS

CABLE

SKIP

PLAY

STOP

SLOW/SEARCH

VOL

SUB TITLE

ANGLE

ZOOM

AUDIO

OPEN/CLOSE

CLEAR

ENTER

ACTION RETURN

D V DFM/TV

S E T

ACTION

SELECT

SET

POWER

Perform “Initial Setup” on page 10.

27DF62-K(E) (P10-11 Initial Setup).p65 2002/04/15, 18:3911

4) Press and press SET to

select and set the month,

date, year, time, and DST

(Daylight Saving Time).

To Make Corrections,

repeatedly press

to move

to error, then correct.

5) Press ACTION twice to start

the clock and exit this mode.

Reset Language, Channels, Clock, Time

3) Press to select

“MANUAL”, then press SET.

(For Auto Clock Set, select “AUTO

CLOCK SET”, and press SET.)

3) Press to select

“ANTENNA”, then

press SET to set

your antenna

system

(“TV” or “CABLE”).

4) Press to select

“AUTO SET”, then

press SET.

• After Channel Auto

Set is finished,

Clock Auto Set will

be performed.

(If clock is set

manually, Clock

Auto Set will not be

performed.)

(“TIME ZONE ADJUST” appears

only when auto clock is set.)

1) Press to

select language

icon.

2) Press SET

repeatedly.

Language

Channels

Clock

Press ACTION*

to display MAIN MENU.

3) Press ACTION to

exit.

1) Press to

select “CH.”

2) Press SET.

1) Press to select

“CLOCK.”

2) Press SET.

For English

For Spanish

For French

DVD

LOCK

LANGUAGE

END :

ACT

SET

DVD

LOCK

LANGUAGE

END :

ACT

SET

MENU PR

NCIPAL

DVD

BLOQUEO

CANAL

RELOJTV

OMA

TERM

NAR :

ACT

ELEG

JAR

SET

HOLA

DVD

BLOCAGE

CANAL

HORLOGETELE

LANGUE

FIN :

ACT

SEL.

REGLER

SET

BONJOUR

DVD

LOCK

LANGUAGE

END :

ACT

SET

HELLO

DVD

LOCK

LANGUAGE

END

ACT

SET

ANT

ENN

ABLE

CHANNEL CAPT

EAK

GNAL

SPLAY

OFF

SELE

SET

END

ACT

SET UP

NNE

AUT

K SET

JUS

SELE

SET

END

ACT

SET

DVD

LOCK

LANGUAGE

END

ACT

SET

SET

BACK

END

ACT

SET

DST

2 / 6/

2002

WED

HOUR

27DF62-K(E) (P12-13 lang ch clk).p65 2002/04/15, 18:3912

Initial Setup

3) Press to select

“TIME ZONE ADJUST”

and press or to

subtract or add hour(s)

as necessary.

4) Press ACTION

twice to exit.

•“TIME ZONE ADJUST”

returns to “0” if clock is set

manually.

(Only when Auto Clock is set.)

Time Zone Adjust

1) Press to

select “CLOCK.”

2) Press SET.

AUT

K SET

JUS

SELE

SET

END

ACT

SET

AUT

K SET

JUS

SELE

SET

END

ACT

SET

HANNEL

ADDED

To add channel:

Select channel with

number keys and

press ADD/DLT.

*Important:

If a remote control button does

not work when pressed, press

the FM/TV button on the remote

and try the button again.

DVD

LOCK

LANGUAGE

END

ACT

SET

LIGHT

TITLE MENU

DISPLAY

ADD/DLT

PAUSE

DSS

CABLE

SKIP

PLAY

STOP

SLOW/SEARCH

SUB TITLE

ANGLE

ZOOM

AUDIO

OPEN/CLOSE

CLEAR

ENTER

ACTION RETURN

D V DFM/TV

S E T

ADD/DLT

SELECT

SET

ACTION

NUMBER keys

HANNEL

To delete channel:

Select channel with

or number keys

and press ADD/DLT.

Time Zone Adjust

Add or Delete a Channel

27DF62-K(E) (P12-13 lang ch clk).p65 2002/04/15, 18:3913

Audio Connections

Amplifier

Unit

Speaker

AUDIO OUT

R L

AUDIO IN

Notes on audio output from the optical digital

audio output connector

Enjoying digital audio output from the

digital audio output connector

*1 The type of audio output from the connector can be

selected by the Settings for DVD Operation. (See

page 49.)

*2 Sound having 96 kHz sampling is converted into 48

kHz sampling when it is output from the unit’s optical

digital audio output connector.

For your reference:

• Dolby Digital is a digital sound compression technique

developed by the Dolby Laboratories Licensing

Corporation. Supporting 5.1-channel surround sound,

as well as stereo (2-channel) sound, this technique

enables a large quantity of sound data to be efficiently

recorded on a disc.

• Linear PCM is a signal recording format used in CDs.

While CDs are recorded in 44.1 kHz/16 bit, DVDs are

recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you

will obtain the full benefit of Pro Logic from the same

DVD movies that provide full 5.1 channel Dolby Digital

soundtracks, as well as from titles with the Dolby

Surround mark. For information on Panasonic or

Technics Dolby Pro Logic Surround Sound Decoders

please contact your local dealer.

Ready Checklist

Turn down the volume, then turn this unit, as well as

other equipment to be connected, off before

proceeding with connection.

Do not block ventilation holes of any of the

equipment and arrange them so that air can circulate

freely.

Read through the instructions before connecting

other equipment.

Ensure that you observe the colour coding when

connecting audio and video cables.

Disc

DVD

Video

MP3

Sound

recording

format

Dolby Digital

Linear PCM

(48/96 kHz

16/20/24 bit)

dts

MPEG 1

Linear PCM

MP3

Optical digital audio

output from connector

Dolby Digital bitstream

(1-5.1 ch) or OFF (no

output)*

Linear PCM (2ch)

(48 kHz sampling/16 bit

only)*

or no output*

Bitstream or no output*

PCM

(44.1 kHz sampling)

Linear PCM

(44.1 kHz sampling)

Linear PCM

(

It depends on the MP3 file)

■ Unit

➛➛

➛ Amplifier

➛➛

➛ Speaker

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and the

double-D symbol are trademarks of Dolby

Laboratories. Confidential Unpublished

27DF62-K(E) (P14-15 Audio connect).p65 2002/04/15, 18:3914

Initial Setup

Unit

Optical digital audio

cable (optional)

Dolby Digital Decoder

dts processing (optional)

Amplifier

Centre speaker

Front

Speaker

Front

Speaker

Subwoofer

Surround

speaker

Surround

speaker

■ Unit

➛➛

➛ Dolby Digital Decoder

➛➛

➛ Amplifier

➛➛

➛ Speaker

Unit

➛➛

➛ dts

(digital theatre systems) Decoder

➛➛

➛ Amplifier

➛➛

➛ Speaker

When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts

bitstream is output from the unit Optical digital audio output connector. When the unit is

connected to a Dolby Digital decoder or dts

decoder, you can enjoy theatre-quality audio

in your home. [An optical digital audio cable (optional) is required when an optional Dolby

Digital decoder or dts

decoder is used.]

Notes on connecting an Optical

digital audio cable (optional)

• Firmly connect the cable to the

connector.

IMPORTANT NOTE:

Caution for optical digital audio output

connector:

• When connecting an amplifier (with

an Optical digital input connector)

which does not contain the Dolby

Digital or dts decoder, be sure to

select “OFF” at “Dolby Digital” and

“OFF” at “dts” of the Settings for DVD

Operation “AUDIO OUTPUT” (see

page 49). Otherwise, any attempt to

play DVDs may cause such a high

level of noise that it may be harmful to

your ears and damage your speakers.

• When a dts decoder is connected,

please select “Bitstream” at “dts” of the

Settings for DVD Operation “AUDIO

OUTPUT”. If “OFF” is selected, there

will be no sound. (See page 49).

• Video CDs and CDs can be played

as normal.

Note:

• Some dts decoders which do not

support DVD-dts Interface may not

work properly with the unit.

27DF62-K(E) (P14-15 Audio connect).p65 2002/04/15, 18:3915

Press or

number key(s) (see

below) to select title

and press SET to

play.

Basic DVD Operation

Ready Checklist

All connections are made.

Your unit is plugged in.

If unit is connected to an audio amplifier,

turn the stereo system’s power on.

Press POWER* on the remote or unit.

Insert a disc.

• If a disc is already inserted, go to step 3.

(Depending on the disc, playback may start

automatically.)

1) Press OPEN/CLOSE.

2) Place disc into disc tray.

Press PLAY to start play.

Disc tray closes automatically.

READING

If an interactive DVD*

or a

Video CD with playback

control*

is used and a TITLE

MENU appears, go to step 5.

• You may also close the tray

by pressing OPEN/CLOSE.

• Data reading time differs with

each disc.

1 2

• Hold disc by its edges only

(page 7

) with printed side up

and

use guides to place into

tray. Use

3”(8 cm) or

5” (12 cm) disc.

Interactive DVD...

May include multiple camera angles,

stories, etc.

Video CD with playback control...

Particular scenes or information can be

interactively selected from a menu that

appears on the screen.

Operation using unit buttons

Press PLAY.

Insert disc.

Press

OPEN/CLOSE.

•

Press STOP.

Press POWER

<Example> 1 digit number 1 ••• 1

2 digit number 12 ••• 10➛1➛2

3 digit number 123 •••100➛1➛2➛3

Press SKIP | or | to go to next or previous menu screen.

• SKIP function not available with all discs.

Please refer to disc jacket for operation information.

T I TLE MENU

Cas t l es

Love

r s

Dogs

i r ds

To return to MENU (play stops)

Press TITLE, MENU, or RETURN. (DVD)

Press RETURN. (Video CD)

Press STOP to stop play.

Press OPEN/CLOSE to eject the disc.

Using number key(s)

starts play automatically.

SKIP |

POWER

NUMBER

keys

TITLE

PLAY

SLOW

PAUSE

SKIP |

OPEN/

DVD

SELECT

SET

SLOW

RETURN

LIGHT

TITLE MENU

DISPLAY

ADD/DLT

PAUSE

DSS

CABLE

SKIP

PLAY

STOP

SLOW/SEARCH

SUB TITLE

ANGLE

ZOOM

AUDIO

OPEN/CLOSE

CLEAR

ENTER

ACTION RETURN

D V DFM/TV

S E T

STOP

27DF62-K(E) (P16-17 Basic DVD).p65 2002/04/15, 18:3916

DVD Operation

• Please read the disc jacket for operation

information.

• If a single sided disc is placed in upside down,

“PLEASE CHECK THE DISC,

AND FOR STAINS OR SCRATCHES ON

DISC” is displayed.

• Remove disc and press unit POWER off when

not in use.

• Disc continues to rotate with menu displayed

even after play is done. Press STOP to clear

menu display when finished with menu.

■ Forward/Reverse rapid scene

➛➛

➛ Press SLOW

or SLOW

during play.

➛➛

➛ Press PLAY to release.

• Starting forward/reverse search during play

started from menu on Video CDs may recall

menu.

• Search speed, slow at first, increases with

each additional press of the button up to 5

levels.

■ Forward/Reverse Chapter/Track

Skip

➛➛

➛ Press SKIP

during play.

Each press skips a chapter (DVD) or

track (Video CD/CD).

Pressing

SKIP once midway through a

chapter/track returns to start of that chapter/track.

Each additional press skips back one chapter/

track.

• Pressing SKIP

during play started

from menu on Video CDs may recall menu.

■ Still (Pause) Picture

➛➛

➛ Press PAUSE during play.

➛➛

➛ Press PLAY to release.

• DVD/Video CD : The unit will enter Still picture mode.

• CD : The unit will enter Pause mode.

■ Frame by Frame picture

(DVD/Video CD)

➛➛

➛ Press PAUSE in Still mode.

➛➛

➛ Press PLAY to release.

• Each press advances picture one frame.

• Hold down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically (see page 50).

■ Slow Motion picture (DVD/Video CD)

➛➛

➛

Press

SLOW or SLOW

in Still mode.

➛➛

➛ Press PLAY to release.

• Slow motion speed, slow at first, is increased

with each additional press of the button up to 5

levels.

• Reverse slow motion is not available for video

CDs.

• When appears on the screen while a button

is being operated, it means that the

corresponding operation is prohibited by the

unit or the disc.

The unit memorizes the point where STOP

is pressed (

flashes on screen).

Press PLAY to resume play from this point.

Pressing STOP again or opening the tray

cancels RESUME, however, RESUME is not

cancelled when power is turned off and on.

• RESUME works only with discs for which

elapsed play time is displayed during play.

RESUME function

Notes

Power turns off after unit has been in Stop

mode (DVD) for about 5 minutes.

Auto-Power Off function

1.Do steps 1-4 (previous page).

When menu appears, press STOP.

2.Press number key(s) to select desired

track (play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,

Press STOP, and press PLAY, then the menu

appears. Now, go to step 5 (previous page).

Enjoy Video CDs featuring

playback control without

using menus (Video CDs only)

Important:

f a remote control button does not work when pressed, press the DVD button on the remote

and try the button again.

Chapter/Track Chapter/Track Chapter/

rackChapter/

rack

Current playback position

Reverse Skip Forward Skip

27DF62-K(E) (P16-17 Basic DVD).p65 2002/04/15, 18:3917

TV Operation

Press POWER* on the remote or unit.

■ Using the 100 key

When selecting CABLE channels 100 to 125

with the number keys, first press the 100 key,

and then enter the remaining two digits.

■ Rapid Tune

Press R-TUNE to display the last channel you

were watching.

■ Audio Mute

Press MUTE to instantly mute the sound.

Press again to restore the previous sound level.

■ Phones

Connect an earphone (not supplied) or

headphones (not supplied) to the Phones Jack.

Ready Checklist

All connections are made.

Your unit is plugged in.

PHONES

Jack

POWER

VOL + / VOL -

Important: If a remote control button does not work

when pressed, press the FM/TV button

on the remote and try the button again.

Use CH or

number keys to

select a channel.

Press VOL + or VOL -

to adjust volume.

LIGHT

TITLE MENU

DISPLAY

ADD/DLT

PAUSE

DSS

CABLE

SKIP

PLAY

STOP

SLOW/SEARCH

VOL

SUB TITLE

ANGLE

ZOOM

AUDIO

OPEN/CLOSE

CLEAR

ENTER

ACTION RETURN

D V DFM/TV

S E T

POWER

VOL + /-

NUMBER

keys

100 key

RAPID

TUNE

27DF62-K(E) (P18 TV).p65 2002/04/15, 18:3918

TV Operation

Receivable Broadcast Types

The following are possible audio broadcast types and

on-screen displays. The signal being received is indicated

with an “ ” mark while the selected audio mode is indicated

with an arrow. To change the audio mode for these

broadcasts, see the “Select Audio Mode for TV Viewing”

section (below.)

Press DISPLAY to display

the broadcast signal being received.

MTS Stereo and SAP broadcast

Multi-channel Television Sound Stereo

(main language) and Secondary Audio

Program (sub language) broadcasts are

being received simultaneously.

Select the STEREO or SAP audio mode.

MTS Stereo broadcast

Multi-channel Television Sound Stereo

broadcast. Select STEREO audio mode.

• If stereo broadcast is weak and the

display flickers, select MONO audio

mode for possible improvement.

SAP broadcast

Secondary Audio Program

(sub language).

Select SAP audio mode for the sub

language.

Audio Mode for TV Viewing

Press AUDIO to select the desired audio mode as

described above.

(Arrow shows selection.)

• Each press of AUDIO will change the audio mode as shown below.

• “SAP” is selected with first press of AUDIO.

MTS Broadcast

TV Stereo System

MONO broadcast

Normal monaural sound broadcast.

< Example >

Press AUDIO

Equipped with

-TV Noise

Reduction for true MTS

reproduction.

-TV Noise

Reduction is required for good

stereo separation and audio fidelity.

is a registered trademark, and

is licensed by

Technology

Licensing.

LIGHT

TITLE MENU

DISPLAY

ADD/DLT

PAUSE

DSS

CABLE

SKIP

PLAY

STOP

SLOW/SEARCH

VOL

SUB TITLE

ANGLE

ZOOM

AUDIO

OPEN/CLOSE

CLEAR

ENTER

ACTION RETURN

D V DFM/TV

S E T

AUDIO

DISPLAY

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

27DF62-K(E) (P19 MTS).p65 2002/04/15, 18:3919

Closed Caption Mode Feature

Closed Caption System

Closed Caption is ...

This multi-use system not only allows the hearing impaired to enjoy selected programs,

but also makes useful information from TV stations available to everyone.

Press ACTION*

to display MAIN MENU.

Closed Caption Mode Selections

Caption Mode: CAP C1 or C2

A narration of selected TV programs

is displayed.

Check TV program listings for CC

(Closed Caption) broadcasts.

Caption Mode: TEXT C1 or C2

Most of the screen will be blocked

out. When the TV station broadcasts

information, such as program listings,

it will appear in this space.

Caption Mode: OFF

Closed Caption /Text narration will

not be displayed.

NOTE :

The closed caption or text signal may

be broadcast over C1, C2, or both.

Also, text contents can vary so you

may wish to try different settings.

Press ACTION three times

to return to the normal screen.

1)Press to

select “TV.”

2)Press SET to

display SET UP

TV screen.

1) Press to

select “CAPTION”.

2) Press SET

to display

CAPTION screen.

OFF

CAP C1

TEXT C1

CAP C2

TEXT C2

1) Press to

select CAPTION

MODE.

2) Press SET

repeatedly to select

mode. (See right.)

CAPT

MODE

CAP C1

CC ON MUTE

CAP C1

SET

END

ACT

DVD

LOCK

LANGUAGE

END :

ACT

SET

SELE

END

ACT

SET

UP TV

SET

SELE

UNER

SET

DEO

ANT

ENN

REMOTE

ARN

DVD

VOL

27DF62-K(E) (P20-21 TV CC).p65 2002/04/15, 18:3920

La page charge ...

Panasonic PV27DF62K Mode d'emploi

Marque: Panasonic

Modèle: PV27DF62K

Catégorie: Lecteurs DVD

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Panasonic PV27DF62K Operating instructions

Panasonic PV27DF62K Mode d'emploi

Panasonic PV27DF62K Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents