GE ZBD6800NBB Guide d'installation

Marque: GE

Modèle: ZBD6800NBB

Catégorie: Lave-vaisselle

Taper: Guide d'installation

If you have questions, call 800.626.2000 or visit our website at: www.monogram.com

Monogram.

Installation

Instructions

Built-In Dishwashers

ZBD6800

ZBD6880

ZBD6890*

ZBD0700*

ZBD0710

Design Guide with

Installation Instructions

*For ZBD6890 and ZBD0700 also refer

to the instructions provided on the

template packed with that model.

Safety Information
2
CONTENTS
Installation Preparation
Parts Supplied..............................................................................3
Materials You Will Need ............................................................3
Tools You Will Need ....................................................................3
Models Available ........................................................................4
Advance Planning ......................................................................4
Prepare Dishwasher Enclosure ................................................4
Drain Requirements ....................................................................5
Prepare Electrical Wiring ..........................................................6
Prepare Hot Water Line..............................................................7
Installation Instructions
Step 1, Check Door Balance......................................................7
Step 2, Remove Wood Base, Install Leveling Legs ..............8
Step 3, Remove ToeKick ............................................................8
Step 4, Install Power Cord ........................................................8
Step 5, Install 90° Elbow ............................................................8
Step 6, Position Water Line and House Wiring......................9
Step 7, Install Drain Hose, Guide Through Cabinet ..............9
Step 8, Slide Dishwasher Partially Into Cabinet ....................9
Step 9, Install Trim Pieces..........................................................9
Step 10, Position Dishwasher Under Countertop ................10
Step 11, Level Dishwasher ......................................................11
Step 12, Secure Dishwasher To Cabinet ..............................12
Step 13, Connect Water Supply ..............................................13
Step 14, Connect Drain Line ....................................................13
Step 15, Connect Power Supply..............................................14
Step 16, Pre-Test Check List....................................................14
Step 17, Dishwasher Wet Test ................................................15
Step 18, Replace Toekick ........................................................15
Step 19, Literature ....................................................................15
Custom Panel Dimensions
Custom Panel for Models ZBD6890, ZBD0700......................15
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• 
IMPORTANT — Save these instructions for
local inspector’s use. Observe all governing codes and
ordinances.
• Note to Installer — Be sure to leave these
instructions with the Consumer.
• Note to Consumer — Keep these instructions 
with your Owner’s Manual for future reference.
• Skill Level — Installation of this dishwasher requires
basic mechanical and electrical skills. Proper installation
is the responsibility of the installer. Product failure due 
to improper installation is not covered under the GE
Appliance Warranty. 
• Completion Time — 1 to 3 Hours.
New installations require more time than replacement
installations.
•
IMPORTANT — The dishwasher MUST 
be installed to allow for future removal from the 
enclosure if service is required.
• If you received a damaged dishwasher, you should 
immediately contact your dealer or builder.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
FOR YOUR SAFETY
Read and observe all CAUTION and WARNINGS shown
throughout these instructions.
While performing installations described in this booklet,
gloves, safety glasses or goggles should be worn.
For Monogram local service in your area, 1.800.444.1845.
For Monogram service in Canada 1.888.880.3030
For Monogram Parts and Accessories, call 1.800.626.2002.

TOOLS YOU WILL NEED:

 Phillips head screwdriver

 5/16" and 1/4" nutdriver

 6" Adjustable wrench

 Level

 Carpenters square

 Measuring tape

 Safety glasses

 Flashlight

 Bucket to catch water when flushing the line

 15/16" socket (optional for skid removal)

 Gloves

For New Installations Only:

 Tubing cutter

 Drill and appropriate bits

 Hole saw set

MATERIALS YOU WILL NEED:

 Ferrule, compression nut and 90° Elbow (3/8" NPT

external thread on one end, opposite end sized to fit

water supply)

 Thread seal tape

 UL Listed wire nuts (3)

Materials For New Installations Only:

 Air gap for drain hose, if required

 Waste tee for house plumbing, if applicable

 Electrical cable or power cord, if applicable

 Screw type hose clamps

 Strain relief for electrical connection

 Hand shut-off valve

 Water line 3/8" min. copper

 Coupler for extending drain line, if applicable

PARTS SUPPLIED:

 Two #8-18 x 5/8" Phillips special head screws, to secure

dishwasher to underside of countertop or sides of

cabinets. (Taped to top side of dishwasher.)

 Side and top trim pieces (on some models)

 Template with mounting hardware (not shown)

for Model ZBD6890 Only

 Drain Hose and Hose Clamp

Installation Preparation

Wire Nuts (3)

Hot Water line

Screw Type

Hose Clamps

Coupler

Hand

Shut-Off

Valve

#8 Phillips Special Head

Screws 5/8" Long

Hole Saw Set

Measuring Tape

Tubing Cutter

Drill and Bits

Phillips

Head

Screwdriver

15/16" Socket

1/4"

and 5/16"

Nutdriver

Safety Glasses

6" Adjustable

Wrench

Bucket

Flashlight

Gloves

Carpenters

Square

Level

Thread

Seal Tape

Air Gap

Strain Relief

Drain Hose

Hose Clamp

90° Elbow,

Ferrule and

Compression Nut

Electrical Cable

(or Power Cord, if applicable)

Waste Tee

Trim Pieces

(on some models)

PREPARE DISHWASHER ENCLOSURE

• The rough cabinet opening must be at least 24" deep,

24" wide and approximately 34-1/2" high from floor to

underside of the countertop.

• Plumbing and electrical service must enter the shaded

area.

• The dishwasher must be installed so that drain hose is

no more than 10 feet in length for proper drainage.

WARNING

To reduce the risk of electric shock, fire,

or injury to persons, the installer must

ensure that the dishwasher is completely

enclosed at the time of installation.

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

28-3/8"

Cabinets

Square

and

Plumb

Floor MUST

be Even with

Room Floor

This Wall Area

must be Free of

Pipes or wires

34-1/2" Min.

Underside of

Countertop

to Floor

24"

Min.

24" Min.

5" 5"

24"

*24"

34"

Adjustable

to 35"

Figure B

Installation Preparation

CLEARANCES: When installed

into a corner, allow 2" min.

clearance between dishwasher

and adjacent cabinet, wall or

other appliances. Allow 28-3/8"

min. clearance from the front of

the dishwasher for door

opening (Figure B).

DISHWASHER MODELS

ZBD0710 SS, Stainless Steel

ZBD6880 SS, Stainless Steel

ZBD6800 BB, Black

ZBD6800 WW, White

ZBD6890 Requires a 3/4" custom panel and handle

ZBD0700 Requires a 3/4" custom panel and handle

ADVANCE PLANNING

• These dishwashers are designed for versatility,

adaptable to virtually any installation.

• All models have a full length door without the

traditional access panel.

• These dishwashers may be installed beneath

countertops of stone or other materials that will not

accept screws. No trim kit required.

*Dishwasher models ZBD6890

and ZBD0700 require a 3/4”

thick custom panel and will be

24-3/4” deep.

Figure A

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 10 feet distance to drain.

• Do not connect drain lines from other devices to the

dishwasher drain hose.

NOTE: An air gap must be used, if waste tee or disposer

connection is less than 18" above floor to prevent

siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

question.

 Do local codes or ordinances require an air gap?

 Is waste tee less than 18" above floor?

If the answer to either question is YES, Method 1 MUST

be used.

• If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2" dia. hole in the cabinet wall within the

shaded areas shown in Figure A for the drain hose

connection. The hole should be smooth with no

sharp edges.

Method 1—Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes and

ordinances. The air gap must be installed according to

manufacturers instructions.

Method 2—“High Drain Loop” with Waste Tee or

Disposer

Figure C

Figure D

32"

Min.

18"

Min.

32"

Min.

18"

Min.

IMPORTANT — When

connecting drain line to disposer,

check to be sure that drain plug has

been removed. DISHWASHER WILL

NOT DRAIN IF PLUG IS LEFT IN PLACE.

Remove

Hopper

Plug

Installation Preparation

PREPARE ELECTRICAL WIRING

WARNING

FOR PERSONAL SAFETY: Remove house

fuse or open circuit breaker before

beginning installation. Do not use an

extension cord or adapter plug with this

appliance.

Electrical Requirements

• This appliance must be supplied with 120V, 60 Hz., and

connected to an individual properly grounded branch

circuit, protected by a 15 or 20 ampere circuit breaker

or time delay fuse.

• Wiring must be 2-wire with ground and rated for

75°C (176°F).

• If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

Grounding Instructions—Cable Direct

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

be connected to the equipment grounding terminal or

lead on the appliance.

Grounding Instructions—Power Cord Models

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current. This appliance is

equipped with a cord having an equipment grounding

conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is installed and

grounded in accordance with all local codes and

ordinances.

WARNING

The improper connection of the equipment

grounding conductor can result in a risk

of electric shock. Check with a qualified

electrician or service representative if you

are in doubt that the appliance is properly

grounded.

For models equipped with power cord: Do not modify

the plug provided with the appliance; if it will not fit the

outlet, have a proper outlet installed by a qualified

technician.

Cabinet Preparation and Wire Routing

• The wiring may enter the opening from either side,

rear or the floor within the shaded area.

• Cut a 1-1/2" max. dia. hole to admit the electrical

cable. Cable direct connections may pass through

the same hole as the drain hose and hot water line,

if convenient. If cabinet wall is metal, the hole edge

must be covered with a bushing.

• NOTE: Power cords with plug must pass through a

separate hole.

Electrical Connection to Dishwasher

Electrical connection is on the right front of

dishwasher.

• For cable direct connections the cable must be

routed as shown in Figure E. Cable must extend

a minimum of 24" from the rear wall.

• For power cord connections, install a 3-prong

grounding type receptacle in the sink cabinet rear

wall, 6" min. or 18" max. from the opening, 6" to 18"

above the floor.

White

18"

24"

from Wall

from

Cabinet

Alternate

Receptacle

Location

Ground

Black

1-1/2" Dia.

Hole (Max.)

18"

Receptacle

Location

Area

Figure E

PREPARE HOT WATER LINE

• The line may enter from either side, rear or floor

within the shaded area shown in Figure F.

• The line may pass through the same hole as the

electrical cable and drain hose. Or, cut an additional

1-1/2" dia. hole to accommodate the water line.

If power cord with plug is used, water line must

not pass through power cord hole.

Water Line Connection

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location,

such as under the sink. (Optional, but strongly

recommended and may be required by local codes.)

• Water connection is on the left side of the dishwasher.

Install the hot water inlet line, using no less than 3/8"

O.D. copper tubing. Route the line as shown in Figure F

and extend forward at least 19" from rear wall.

• Adjust water heater for 120°F to 150°F temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

Installation Instructions

Cabinet Face

Shut-off

Valve

2" From Floor

19" From Wall

From

Cabinet

1-1/2" Dia.

Hole

Hot

CAUTION

Do not remove wood base until you are ready

to install the dishwasher. The dishwasher will tip over

when the door is opened if the wood base is removed.

BEFORE YOU BEGIN

Locate and set aside (for use in Step 12) the

2 Phillips special head screws wrapped with

yellow tape and stuck to the top or side of the

dishwasher. Remove drain hose from upper rack, if

it has not been pre-installed, and set aside for use in

Step 7.

Figure F

CHECK DOOR BALANCE

• With dishwasher on the wood skid, check the door

balance by opening and closing the door.

• If the door drops when released, increase the spring

tension. If the door rises when released, decrease

the tension.

NOTE: The addition of the custom panel on model

ZBD6890 will require exchange of the factory installed

springs. Use the heavy-duty springs provided. See the

custom panel template for additional instructions.

• Position the spring for increased or decreased

tension as required.

NOTE: Adjust both balance springs to the same

amount of tension to prevent excessive door

twisting during use.

TIP: If door does not open easily or falls too quickly,

check the spring cable routing. Check that the cable

is properly aligned on the pulley (as shown).

STEP 1

Correct Spring

Cable Routing

Increase

Tension

Decrease

Tension

Pulley

Shoulder

Use This

Mounting

Hole

Figure G

REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT — Do not kick off wood base! Damage

will occur.

• Move the dishwasher close to the installation location and lay it

on its back.

• Remove the four leveling legs on the underside of the

wood base with an adjustable wrench or 15/16" socket.

• Discard base.

• Screw leveling legs back into the dishwasher frame,

approximately 1/4" from frame as shown.

STEP 2

REMOVE TOEKICK

• Remove the two toekick screws.

STEP 3

oekick

Remove 2

Toekick Screws

Installation Instructions

Figure H

Approx.

1/4"

Figure J

INSTALL POWER CORD

Use Power Cord Kit WX09X70910 available for purchase from an

authorized GE Appliances dealer.

Skip this step if dishwasher will be direct wired or has a

factory installed power cord.

The power cord and connections must comply with the National

Electrical Code, Section 422 and/or local codes and ordinances.

• Maximum power cord length is 4 feet beyond the back of the

dishwasher.

• Connect incoming power cord white (or ribbed) to dishwasher

white, black (or smooth) to black and ground to dishwasher

green wire. Use UL listed wire nuts of appropriate size.

• Replace junction box cover. Be sure wires are not pinched

under the cover.

STEP 4

White

Ground

Black

Check That White, Black and

Green Dishwasher Wires Are Threaded

Thru Small Hole in Bracket

Remove

Junction Box

Cover

Insert Power

Cord Wires Thru

Strain Relief

and Tighten

Use UL Listed

Wire Nuts

Figure K

INSTALL 90° ELBOW

• Wrap 90° elbow with thread seal tape.

• Install a 90° elbow onto the water valve.

• Do not overtighten 90° elbow, water valve bracket could bend

or water valve fitting could break.

• Position the end of the elbow to face the rear of the dishwasher

STEP 5

Front of Dishwasher

90°

Elbow

Thread

Seal Tape

Fill

Hose

Water Valve

Bracket

Figure L

INSTALL DRAIN HOSE,

GUIDE THROUGH CABINET

• Remove tape and wire tie holding the clamp to the

drain hose. Be careful not to damage the drain hose.

• Stand the dishwasher upright.

• Slip the supplied

hose clamp over

the large end of

the hose. Do not

tighten.

• Push hose over the drain outlet on the back side of

the dishwasher. See illustration. Push the hose over

the outlet and against the shoulder stop.

• Tighten the hose clamp with a 1/4" nut driver.

• Position the dishwasher in front of the opening.

Insert drain hose into the cabinet side. If power cord

is used, guide the end through a separate hole.

STEP 7

INSTALL TRIM PIECES

Skip this step if trim is not supplied with the

dishwasher.

• Locate trim strips inside dishwasher.

• Press trim onto the tub flange on each side. Start

with the top edge, pressing on as you move towards

the bottom.

• Press the two top trim pieces on each side of

the latch.

• Open and close the door to check that trim does not

bind and does not interfere with door latch.

STEP 9

POSITION WATER LINE

AND HOUSING WIRING

• Position water supply line and house wiring on the

floor of the opening to avoid interference with base

of dishwasher and components under dishwasher.

STEP 6

Figure Q

Trim Strip

Trim

Strip

Trim

Strip

Water

Line

House

Wiring

Installation Instructions

Figure M

SLIDE DISHWASHER

PARTIALLY INTO CABINET

DO NOT PUSH AGAINST FRONT PANEL WITH KNEES.

DAMAGE WILL OCCUR.

• Slide dishwasher into the opening a few inches

at a time.

• As you proceed, pull the drain hose through the

opening under the sink. Stop pushing when the

dishwasher is a few inches forward of adjacent

cabinetry.

• Make sure drain hose is not kinked under the

dishwasher and there is no interference with the

water line and wiring or any other component.

STEP 8

Do Not Push Against

Front Door Panel With

Knee. Damage to The

Door Panel Will Occur.

Reposition Dishwasher

by Grasping Both

Sides With Hands

Figure P

Power Cord

(If Used)

Water

Line

House

Wiring

Drain

Hose

Insulation

Blanket

Figure O

Figure N

Drain

Outlet

Hose

Clamp

Shoulder

Stop

Flapper

Valve—Do

Not Remove

POSITION DISHWASHER UNDER COUNTERTOP

STEP 10

• Push the dishwasher into the cabinet.

• Push at the sides with your hands. Do not use your

knee against the door since door damage will occur.

• Check that the tub insulation blanket does not get

“bunched-up” or interfere with the springs as you

slide it into the cabinet.

• Center the dishwasher in the opening.

• Check that the edges of the dishwasher door are

behind the cabinet frame and aligned with the front

face of the cabinet as shown.

• Carefully open and close the door to ensure that the

door panel does not catch or rub on the cabinet frame.

• If the door catches or rubs on the frame, reposition

and/or level the unit (see Step 11) until the door moves

freely and does not contact the cabinet frame.

The controls are designed to be hidden by your

countertop. Align the dishwasher as shown in Figure T.

NOTE: If the drain hose gets trapped between the wall

and the back side of the dishwasher, it can prevent the

dishwasher from sliding all the way back into the

cabinet opening, and thus preventing a flush fit with

the kitchen cabinet panels.

TIP: For best appearance installations of custom panel

models, it may be necessary to cut off the back panel

of the tub insulation blanket so that the dishwasher

door panel can be aligned flush with the kitchen

cabinet panels.

The leveling legs can be used to increase or decrease

the amount of gap between the controls and the

countertop affecting the visibility of the controls.

Leave a 1/2" minimum gap between the underside

of the countertop and the top of the dishwasher

door (see Figure V).

IMPORTANT — Leave a 1/2" minimum

gap between the controls and the underside of the

countertop to prevent condensation and damage to the

control panel from screwheads.

NOTE: If this dishwasher is replacing an existing

dishwasher, the old countertop bracket screw holes

may not be in the correct position to accept a top

control model. New holes may be required.

Control Panel

Countertop

Minimum 1/2" Gap

for Clearance

Countertop

1/2" min.

Figure U

Figure V

Top View

Controls Hidden

by Countertop

Installation Instructions

Door

Fits and

Swings

Back

Behind

Cabinet

Frame

Correct

Alignment

Door Catches

on Cabinet Frame

Incorrect

Alignment

Figure S

Figure T

Do Not Push Against

Front Door Panel With

Knee. Damage to The

Door Panel Will Occur.

Reposition Dishwasher

by Grasping Both

Sides With Hands

Figure R

LEVEL DISHWASHER

IMPORTANT — Dishwasher must be level

for proper dish rack operation and wash performance.

• Place level on door

and rack track inside

the tub as shown to

check that the

dishwasher is level.

• Level the

dishwasher by

adjusting the

four leveling legs

individually.

• Make sure 1/2"

minimum gap is

maintained (see

Figure V).

• If adjustment to the right rear leveling leg is required,

gain access by loosening junction box bracket screw

(through the access hole) and rotate bracket

clockwise.

TIP: Pull lower rack out, about halfway. Check to

be sure the rack does not roll forward or back into

dishwasher. If the rack rolls in either direction, the

dishwasher must be leveled again.

• If the door hits the tub, the dishwasher is not installed

correctly. Adjust leveling legs to align door to tub.

STEP 11

Check

Level

Side

To Side

Check

Level

Front

to Back

Turn Legs

to Adjust

Access Hole

Installation Instructions

Figure W

Figure X

Installation Instructions

SECURE DISHWASHER TO CABINET

STEP 12

The dishwasher must be secured to the countertop or

the cabinet sides. When countertops are made of wood,

use Method 1. When countertops are granite or other

materials that will not accept screws, use Method 2 to

secure dishwasher at the sides.

IMPORTANT — After leveling, verify that

the dishwasher is still in the correct position shown in

Step 10.

IMPORTANT — Drive screws straight and

flush. Protruding screw heads will scratch the top or

sides of the control panel and can interfere with door

closing.

Method 1—Secure dishwasher to wood

countertop

• Fasten the dishwasher to the underside of the

countertop with 2 Phillips screws provided.

Method 2—Secure dishwasher with side

mounting brackets

• Remove plug buttons (one on each side).

• Install screw through the hole in the side of the

dishwasher and into the adjacent cabinet.

Reinstall plug buttons.

Both Methods—Maintain 1/2" Gap

Countertop

Mounting

Brackets

Tub

Frame

Side Mounting

Brackets

Figure Y

Figure AA

Brackets

Wood Countertop

Screws

Plug Buttons

Side Mounting Brackets

Stone Countertop

Figure Z

Figure Y

1/2” Min.

Gap

Figure BB

Installation Instructions

CONNECT DRAIN LINE

FOLLOW ALL LOCAL CODES AND ORDINANCES.

The drain hose molded end will fit 5/8" or 1" diameter

connections on the air gap, waste tee or disposer. Cut

on the marked line as required for your installation.

• If a longer drain hose is required, add up to 42" of

length for a total of 10 ft. to the factory installed hose.

Use 5/8" or 7/8" inside diameter hose and a coupler to

connect the two hose ends. Secure the connection

with hose clamps.

• Secure the drain hose to the air gap, waste tee or

disposer with clamps.

NOTE: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED

10 FEET FOR PROPER DRAIN OPERATION.

DRAIN LINE INSTALLATION

• Connect drain line to air gap, waste tee or disposer

using either previously determined method.

Method 1—Air gap with waste tee or disposer

Method 2—“High drain loop” with waste tee or

disposer

IMPORTANT — When

connecting drain line to disposer,

check to be sure that drain plug has

been removed. DISHWASHER WILL

NOT DRAIN IF PLUG IS LEFT IN PLACE.

TIP: Avoid unnecessary service call charges. Always

be sure disposer drain plug has been removed before

attaching dishwasher drain hose to the disposer.

STEP 14

CONNECT WATER SUPPLY

Connect water supply line to 90° elbow.

• Slide compression nut, then ferrule over end of

water line.

• Insert water line into 90° elbow.

• Slide ferrule against elbow and secure with

compression nut.

IMPORTANT — Check to be sure that door

spring does not rub or contact the fill hose or water supply

line. Test by opening and closing the door. Re-route the

lines if a rubbing noise or interference occurs.

STEP 13

90° Elbow

Ferrule

90° Elbow

Compression Nut

Door Spring

Hot Water

Supply Line

Figure CC

Cutting Line

5/8"

IMPORTANT: Do not cut corrugated

portion of hose

Figure DD

Hose Clamp

Coupler

Hose Clamp

Figure EE

Figure FF

Waste Tee Installation Disposer Installation

Figure GG

Fasten to underside

of countertop

32"

Min.

18"

Min.

Fasten to underside

of countertop

32"

Min.

18"

Min.

Disposer InstallationWaste Tee Installation

Remove

Hopper

Plug

Installation Instructions

PRE-TEST CHECK LIST

Review this list after installing your dishwasher to

avoid charges for a service call that is not covered

by your warranty.

 Check to be sure power is OFF.

 Open door and remove all foam and paper

packaging.

 Locate the Owner’s Manual in the literature

package.

 Read the Owner’s Manual for operating instructions.

 Check door opening and closing. If door does not

open and close freely or tends to fall, check spring

cable routing and spring adjustments. See Step 1.

 Check to be sure that wiring is secure under the

dishwasher, not pinched or in contact with door

springs or other components. See Steps 8 and 10.

 Check door alignment with tub. If door hits tub,

level dishwasher. See Step 11.

 Pull lower rack out, about half way. Check to be

sure it does not roll back or forward on the door.

If the rack moves, adjust leveling legs. See Step 11.

 Check door alignment with cabinet. If door hits

cabinet, reposition or relevel dishwasher. See

Steps 10, 11 and 12.

 Check that door spring does not contact water line,

fill hose, wiring or other components. See Step 13.

 Verify water supply and drain lines are not kinked

or in contact with other components. Contact with

motor or dishwasher frame could cause noise.

See Steps 6 and 8.

 Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must

be between 120°F and 150°F. A minimum of 120°F

temperature is required for best wash performance.

See “Prepare Hot Water Line,” page 7.

 Add 2 quarts of water to the bottom of the

dishwasher to lubricate the pump seal.

 Turn on water supply. Check for leaks. Tighten

connections if needed.

 Remove protective film if present from the control

panel and door.

STEP 16

CONNECT POWER SUPPLY

Skip this step if equipped with power cord.

Go to step 16.

Verify that power is turned off at the source.

• Remove junction box cover “A”.

• Secure house wiring to the back of the junction box

with a strain relief “B”.

• Locate the three dishwasher wires, (white, black

and green) with stripped ends. Insert dishwasher

wires through the small hole in the junction box “C”.

Use wire nuts to connect incoming ground to green,

white to white and black to black “D”.

• Replace junction box cover “E”. Check to be sure

that wires are not pinched under the cover.

WARNING

If house wiring is not 2-wire with ground,

a ground must be provided by the

installer. When house wiring is aluminum,

be sure to use UL Listed anti-oxidant

compound and aluminum-to-copper

connectors.

STEP 15

White

Ground

Black

Check That White, Black and

Green Dishwasher Wires Are Threaded

Thru Small Hole in Bracket

Remove

Junction Box

Cover

Insert Power

Cord Wires Thru

Strain Relief

and Tighten

Use UL Listed

Wire Nuts

Replace Junction Box Cover

Figure HH

REPLACE TOEKICK

• Place toekick against the legs of the dishwasher.

• Align the toekick with the bottom edge and make sure it is

against the floor.

• Insert and tighten the two toekick attachment screws. The

toekick should stay in contact with the floor.

TIP: Make sure toekick is against floor to minimize noise.

STEP 18

Attachment Screws

Installation Instructions/Custom Panel Dimensions

LITERATURE

• Be sure to leave complete literature package and installation

instructions with the consumer.

STEP 19

Figure II

DISHWASHER WET TEST

 Turn on power supply (or plug power cord into outlet, if

equipped).

 Start the unit to check for leaks.

– Push RINSE ONLY pad.

– Push START/RESET pad one time.

– Close door.

 Check to be sure that water enters the dishwasher. If water

does not enter the dishwasher, check to be sure that water

and power are turned on.

 Check for leaks under the dishwasher. If a leak is found, turn

power supply off, then tighten connections. Restore power

after leak is corrected.

 Check for leaks around the door. A leak around the door

could be caused by door rubbing or hitting against adjacent

cabinetry. Reposition the dishwasher if necessary. See Step 12.

 The dishwasher will drain and turn off about 5 minutes after it

was started. Check drain lines. If leaks are found, turn power

off at the breaker and correct plumbing as necessary. Restore

power after corrections are made. See Step 15.

 Open dishwasher door and make sure most of the water has

drained. If not, check that disposer plug has been removed

and/or air gap is not plugged. See Step 14. Also check drain

line for kinking.

 Run the dishwasher through another “Rinse Only” cycle.

Check for leaks and correct if required.

STEP 17

CUSTOM PANEL FOR MODEL

ZBD6890, ZBD0700

These dishwashers require a field installed 3/4" thick custom

panel and custom handle. An installation template is packed

with these models and may be obtained in advance. Order

Pub. No. 31-30569-1. Complete panel installation instructions

are included on the template.

CUSTOM PANEL SIZE REQUIREMENTS

HEIGHT

Panel height must be between 30-1/16" and 30-1/4".

• If the panel height is more than 30-1/4" it will prevent the door

from swinging open.

• If the panel height is less than 30-1/16" it will not cover the

dishwasher door frame.

• The top of the custom panel must be flush with the top of the

door. The 1/2" minimum gap between the top of the door and

the bottom of the countertop must be maintained.

WIDTH

Panel width must be 23-3/4".

• If the panel width is less than 23-3/4" it will not cover the

dishwasher frame.

IMPORTANT: To ensure optimum door balance performance,

the custom panel must not weigh more than 14 lbs

Minimum 1/2" Gap

for Clearance

Countertop

1/2" min.

23-3/4"

30-1/16" Min.

30-1/4" Max.

Pub. No. 31-30586

Part No. 206C1559P126

11-04 JR

NOTE: While performing installations described in this book,

safety glasses or goggles should be worn.

For Monogram

local service in your area, call

1.800.444.1845.

NOTE: Product improvement is a continuing endeavor at

General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

En cas de question, appeler 800.626.2000 ou rendre visite à notre site web : www.monogram.com

Monogram.

Instructions

d’installation

Lave-vaisselle encastré

ZBD6800

ZBD6880

ZBD6890*

ZBD0700*

ZBD0710

Guide de conception

Instructions d’installation

*Pour ZBD6890 et ZBD0700, consulter

aussi les instructions imprimées sur

le gabarit fourni avec ce modèle.

Information de sécurité
2
CONTENU
Préparation pour l’installation
Pièces fournies ............................................................................3
Matériaux nécessaires ..............................................................3
Outils nécessaires ......................................................................3
Modèles disponibles ..................................................................4
Planification préalable................................................................4
Préparation de l’enceinte du lave-vaisselle ..........................4
Égout..............................................................................................5
Préparation pour le branchement électrique ........................6
Préparation du tuyau d’eau chaude ........................................7
Instructions d’installation
Étape 1, Vérifier l’équilibre de la porte....................................7
Étape 2, Dépose de la base en bois, installation 
des pattes de mise à niveau ......................................8
Étape 3, Dépose de la plinthe....................................................8
Étape 4, Installation du cordon d’alimentation ......................8
Étape 5, Installation du coude à angle droit ..........................8
Étape 6, Mise en place du tuyau d’eau et 
des fils de la maison....................................................9
Étape 7, Installation du tuyau de vidange, 
guidage dans l’armoire ..............................................9
Étape 8, Glisser le lave-vaisselle partiellement dans
l’ouverture de l’armoire ..............................................9
Étape 9, Installation des pièces de finition ............................9
Étape 10, Mise en position du lave-vaisselle 
sous le plan de travail ............................................10
Étape 11, Mise à niveau du lave-vaisselle............................11
Étape 12, Fixation du lave-vaisselle à l’armoire ..................12
Étape 13, Branchement de l’alimentation d’eau ..................13
Étape 14, Branchement du tuyau de vidange ......................13
Étape 15, Branchement de l’alimentation électrique..........14
Étape 16, Liste de vérification avant de faire les essais ....14
Étape 17, Essai du lave-vaisselle avec de l’eau ..................15
Étape 18, Repose de la plinthe................................................15
Étape 19, Documentation ........................................................15
Dimensions du panneau sur commande
Panneau sur commande pour modèles 
ZBD6890, ZBD0700 ....................................................................15
AVANT DE COMMENCER
Il faut lire soigneusement toutes ces instructions.
• 
IMPORTANT — Conserver ces instructions
afin que l’inspecteur local s’en serve. Il faut respecter tous
les codes et règlements.
•
Remarque pour l’installateur
— Ne pas oublier
de remettre ces instructions au consommateur.
•
Remarque pour le consommateur
—
Il faut garder ces instructions avec le manuel d’utilisation,
pour consultation ultérieure.
•
Niveau de compétence
— L’installation de ce
lave-vaisselle demande des talents mécaniques et
électriques de base. L’installateur est responsable de
l’installation appropriée. La garantie des appareils
ménagers de GE ne couvre pas les défaillances du 
produit causées par une mauvaise installation.
•
Durée d’installation — 1 à 3 heures.
Les installations initiales demandent plus de temps que 
les installations de remplacement.
•
IMPORTANT — Le lave-vaisselle DOIT être
installé de manière à permettre la dépose ultérieure de
l’enceinte afin de permettre toute intervention.
• Si le lave-vaisselle livré est endommagé, il faut contacter
immédiatement le concessionnaire ou l’entrepreneur de
construction.
LIRE ATTENTIVEMENT.
IL FAUT GARDER CES
INSTRUCTIONS.
SÉCURITÉ
Il faut lire et observer tous les avertissements (PRUDENCE
et ATTENTION) montrés dans ces instructions. 
Pendant l’installation décrite dans ce livret, il faut porter
des gants et des lunettes de sécurité.
Pour le service local Monogram dans votre région :
1.800.444.1845.
Pour le service Monogram au Canada : 1.888.880.3030
Pièces et accessoires Monogram, appeler le :
1.800.626.2002.

OUTILS NÉCESSAIRES :

 Tournevis cruciforme

 Tournevis à douille de 5/16 po et 1/4 po

 Clé à molette de 15 cm (6 po)

 Niveau

 Equerre de menuisier

 Mètre ruban

 Lunettes de sécurité

 Lampe de poche

 Seau pour attraper l’eau lors de la purge

du tuyau

 Douille de 15/16 po (optionnelle pour

la dépose de la palette)

 Gants

Pour les installations initiales

seulement :

 Coupe-tube

 Perceuse et mèches appropriées

 Scie-cloche

MATÉRIAUX NÉCESSAIRES :

 Bague, écrou de compression et coude à angle droit

(filetage externe de 3/8 po à une extrémité, l’autre

extrémité correspondant à l’alimentation d’eau)

 Ruban d’étanchéité de filetage

 Serre-fils sur la liste UL (3)

Matériaux pour une installation initiale

seulement :

 Dispositif anti-siphon pour le tuyau de vidange, si nécessaire

 Raccord en té pour la plomberie d’égout, si nécessaire

 Câble électrique ou cordon d’alimentation,

si nécessaire

 Colliers de tuyau à vis

 Dispositif de réduction de tension pour les

branchements électriques

 Robinet

 Conduite d’eau en cuivre de 3/8 po minimum

 Manchon pour allonger le tuyau de vidange, si nécessaire

PIÈCES FOURNIES :

 Deux vis cruciformes spéciales #8-18 x 5/8 po (enveloppées

dans du ruban adhésif sur le côté supérieur du lave-vaisselle)

pour fixer le lave-vaisselle au dessous du plan de travail ou

aux côtés des armoires

 Pièces de finition latérales et supérieure (sur certains modèles)

 Gabarit avec quincaillerie de montage (non illustré)

Modèle ZBD6890 seulement

 Tuyau de vidange et collier de tuyau

Préparation pour l’installation

Serre-fils (3)

Tuyau d’eau

chaude

Colliers de

tuyau à vis

Manchon

Robinet

Vis cruciformes

spéciales #8 de 5/8

po de long

Scie-cloche

Mètre ruban

Coupe-tube

Perceuse et

mèches

appropriées

Tournevis

cruciforme

Douille de

15/16 po

Tournevis à douille

de 5/16 po et 1/4 po

Lunettes de sécurité

Clé à molette

de 15 cm (6 po)

Seau

Lampe de poche

Gants

Equerre de

menuisier

Niveau

Ruban

d’étanchéité

de filetage

Dispositif

anti-siphon

Dispositif de

réduction de

tension

Tuyau de vidange

Collier

de tuyau

Coude à angle droit,

bague et écrou de

compression

Câble électrique (ou cordon

d’alimentation, si nécessaire)

Raccord en té

Pièces de finition

(sur certains

modèles)

Espace pour l’ouverture

de la porte, au mois 5 cm (2 po)

Plan de travail

Lave-vaisselle

72 cm

86,4 cm (34 po)

ajustable à

88,9 cm (35 po)

10 cm

15 cm

10 cm

Armoire

à l’équerre

et d’aplomb

Le sol DOIT

être au même

niveau que le sol

de la pièce

Cette portion du mur

ne doit pas avoir

de tuyaux ni de fils

88 cm

(34-1/2 po) Min.

dessous du plan

de travail au sol

61 cm

(24 po)

Min.

61 cm

(24 po) Min.

12,5

*61 cm

(24 po)

61 cm

(24 po)

Figure B

Préparation pour l’installation

ESPACES : En cas d’installation

dans un coin, laisser un espace de

5 cm (2 po) minimum entre le lave-

vaisselle et l’armoire, le mur ou un

autre appareil adjacent. Il doit y

avoir un espace d’au mois 72 cm

(28-3/8 po) devant le lavevaisselle

pour permettre l’ouverture la porte

(Figure B).

MODÈLES DE LAVE-VAISSELLE

ZBD0710 SS, Acier inoxydable

ZBD6880 SS, Acier inoxydable

ZBD6800 BB, Noir

ZBD6800 WW, Blanc

ZBD6890 Nécessite un panneau de 1,9 cm (3/4 po) et

une poignée sur commande

ZBD0700 Nécessite un panneau de 1,9 cm (3/4 po) et

une poignée sur commande

PLANIFICATION PRÉALABLE

• Ces lave-vaisselle sont conçus afin d’être polyvalents

et de pouvoir s’adapter à pour ainsi dire n’importe

quelle installation.

• Tous les modèles ont une porte pleine longueur sans

le panneau d’accès traditionnel.

• Ces lave-vaisselle peuvent être installés au-dessous

des plans de travail faits de pierre ou d’autres

matériaux dans lesquels on ne peut pas placer de vis.

Il n’y a pas besoin de trousse de garniture.

*Les lave-vaisselles modèles ZBD6890

et ZBD0700 nécessitent un panneau

sur commande de 1,9 cm (3/4 po)

d’épaisseur et aura 62,9 cm (24-3/4 po)

de profondeur.

Figure A

ATTENTION

Pour réduire le risque de choc

électrique, d’incendie ou de blessures,

l’installateur doit s’assurer, au moment

de l’installation, que le lave-vaisselle

est complètement enclos.

• L’ouverture de l’armoire doit avoir une profondeur d’au

moins 61 cm (24 po), une largeur d’au moins 61 cm

(24 po) et une hauteur d’environ 88 cm (34-1/2 po),

du sol au-dessous du plan de travail.

• La plomberie et l’électricité doivent entrer dans la zone

ombrée.

• Le lave-vaisselle doit être installé de manière que le

tuyau de vidange n’ait pas une longueur supérieure

à 3 m (10 pi) afin d’obtenir un bon écoulement.

PRÉPARATION DE L’ENCEINTE DU LAVE-VAISSELLE

La page charge ...

GE ZBD6800NBB Guide d'installation

Marque: GE

Modèle: ZBD6800NBB

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE ZBD6800NBB Installation guide

GE ZBD6800NBB Guide d'installation

GE ZBD6800NBB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents