Yes DW80CG5450MT Guide d'installation

Dishwasher

Installation manual

DW80CB5450****, DW80CG5450****, DW80CG5420****,

DW80CG5020****, DW80CG5451****

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 1DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 1 2023-05-03  11:49:482023-05-03  11:49:48

Contents

English2

Contents

Safety instructions 3

Important safety instructions 3

Before using your dishwasher 5

Installation 6

Product dimensions 11

Cabinet dimensions 12

Specications 38

Scan the QR code* to view our

helpful installation videos.

* Requires reader to be installed on your

smartphone.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 2DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 2 2023-05-03  11:49:592023-05-03  11:49:59

Safety instructions

English 3

SAVE THESE INSTRUCTIONS

Safety instructions

Throughout this manual, you will see Warning and Caution notes. The warnings, cautions,

and the important safety instructions that follow do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care

when installing, maintaining, and operating the dishwasher. Samsung is not liable for

damages resulting from improper use.

Important safety instructions

What the icons and signs in this installation guide mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in personal injury or property damage.

CAUTION

To reduce the risk of re, explosion, electric shock, or personal injury when using the

dishwasher, follow these basic safety precautions:

NOTE

Indicates that a risk of personal injury or material damage exists.

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

STOP

These installation instructions are intended for use by qualied installers.

If you are having problems installing this dishwasher

U.S.A

Please call: 1-800-SAMSUNG (726-7864)

1-844-SAM-PAYS (726-7297)

for assistance: www.samsung.com/us/support

CANADA

Please call: 1-800-SAMSUNG (726-7864)

for assistance: www.samsung.com/ca/support (English)

www.samsung.com/ca_fr/support (French)

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 3DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 3 2023-05-03  11:49:592023-05-03  11:49:59

Safety instructions

English4

SAVE THESE INSTRUCTIONS

California Proposition 65 Warning

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Read all instructions before using the appliance.

Install and store the dishwasher inside, away from exposure to weather.

CAUTION

• Do not install the dishwasher near electrical components. Keep the dishwasher away

from open ames.

• Do not install the dishwasher on a carpet as this is a re hazard.

• Do not install the dishwasher in a location where the water may freeze (where the

temperature falls below 32 °F (0 °C)). Frozen water in the hoses or pipes may damage

the dishwasher.

• As with all equipment using electricity, water, and moving parts, potential hazards

exist. To safely operate this appliance, become familiar with its operation and exercise

care when using it.

The dishwasher must be properly grounded. Never connect it to an ungrounded outlet.

Prior to removal of original dishwasher and the installation of your new unit, make

sure to switch off your circuit breaker. Do not connect the dishwasher until you have

completed the installation. Connecting the power cable is the last step when installing the

dishwasher.

All wiring and grounding must be done in accordance with the electrical code applicable

to the region.

GROUNDING INSTRUCTIONS

For a permanently connected appliance:

This appliance must be connected to grounded metal, a permanent wiring system, or an

equipment-grounding conductor must be run with the circuit conductors and connected to

the equipment-grounding terminal or lead on the appliance.

The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two

or more people are needed to move a dishwasher and avoid potential injuries.

CAUTION

• If the power cable is damaged, it must be replaced by the manufacturer, a service

agent or similarly qualied person in order to avoid a hazard.

• Do not touch the power cable with wet hands.

• Do not connect another appliance to the same power outlet as the dishwasher.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 4DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 4 2023-05-03  11:50:002023-05-03  11:50:00

Safety instructions

English 5

SAVE THESE INSTRUCTIONS

Make sure to use a new water supply line. Old lines are susceptible to breakage because

they become hardened and may cause property damage due to a water leakage.

The dishwasher must be connected to a hot water supply with a temperature between

120 °F (49 °C)~149 °F (65 °C). This temperature range provides the best washing result

and shortest cycle time. Temperature should not exceed 149 °F (65 °C) to prevent damage

to dishes.

Ensure that the water supplied to the dishwasher does not freeze. Frozen water can

damage the hoses, valves, pump, or other components.

Certied residential dishwashers are not intended for licensed food establishments.

(NSF/ANSI Standard 184 for Residential Dishwashers)

For a full list of safety information, please refer to the User Manual.

Before using your dishwasher

WARNING

Tip-Over Hazard

• Do not use the dishwasher until it is correctly installed.

• Do not push down on the dishwasher door when it is open.

• Do not place excessive weight on the dishwasher door when it is open.

Electric Shock Hazard

Failure to follow these instructions can result in death, re, or electric

shock:

• Electrically ground the dishwasher.

• Connect the ground wire to the green ground connector in the junction

box.

• Do not use an extension cord.

To reduce the risk of electric shock, re, or injury to persons, the installer

must ensure that the dishwasher is completely enclosed at the time of

installation.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 5DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 5 2023-05-03  11:50:002023-05-03  11:50:00

Installation

English6

Installation

Be sure that you or your installer follow these instructions closely so that the new

dishwasher works properly and that you are not at risk of injury when washing dishes.

STEP 1 Check the parts and tools

Before starting on the installation, prepare all the necessary tools and parts required to

install the dishwasher. This will save installation time and simplify the installation process.

Parts required

Provided with the dishwasher. Check when you unbox the dishwasher in STEP 5.

2 Installation brackets Kick Plate 4 screws

(for the Bracket Installation)

Protective sticker Nut connector & seal

(for

3

/

4

" 90° tting)

4 plastic caps

2 black color screws

(for the Kick plate)

2 screws

(for the bespoke door)

2 plastic caps

(for the bespoke door)

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 6DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 6 2023-05-03  11:50:002023-05-03  11:50:00

English 7

Installation

Not provided

Power cable Twist on wire

connector

Strain relief Electrical tape &

Standard duct tape

Hot water supply

line

90° Fitting (

3

/

4

") Tube ttings Air gap

Rubber connector Hose clamp

NOTE

For the hot water supply line – We strongly recommend using

3

/

8

" minimum O.D. copper

tubing with a compression tting or a exible stainless steel braided hot water supply

line.

[Warning: Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a

leak inside the tube tting.]

You also need a 90° Fitting with

3

/

4

" N.P.T. external pipe threads on one end and a tting

sized to t your hot water supply line (copper tubing/compression tting or braided hose)

on the other.

For the power cable, we recommend a jacketed 12-2 cable with ground. Note that some

local codes may require the cable to have a BX style metal jacket.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 7DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 7 2023-05-03  11:50:002023-05-03  11:50:00

Installation

English8

Tools required

Electric drill Safety glasses Gloves Flashlight

Adjustable wrench Wire stripper Pliers Nipper

Tape measure Pencil Phillips screwdriver Flat screwdriver

Tubing cutter Cutting knife Hole saw Level

Torx t20 Hex L-wrench Suction cup

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 8DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 8 2023-05-03  11:50:012023-05-03  11:50:01

English 9

Installation

NOTE

New installation

If the dishwasher is a new installation, most of the installation work must be done before

the dishwasher is moved into place.

Replacement

If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher

connections for compatibility with the new dishwasher. Replace the existing connections

as necessary.

STEP 2 Select the best location for the dishwasher

The following criteria are important to ensure the best location for the dishwasher:

• The location must have a solid oor that is able to support the weight of the

dishwasher.

• The location must be near a sink with easy access to the water supply, drain, and

electrical outlet.

NOTE

For the drain to operate properly, the dishwasher should be installed within 9.8 ft (3 m)

of the sink.

• The location must let you load your dishes into the dishwasher easily.

• The location must have sufcient space for the dishwasher door to open easily and

provide enough space between the dishwasher and the cabinet sides (at least 0.1 in

(2 mm)).

NOTE

If the dishwasher is installed in a corner, ensure that the side of the dishwasher is more

than 2 in. (50 mm) from the wall or cabinet to its right or left.

• The wall at the back must be free of obstructions.

• Make sure the cabinet for the dishwasher is secured to the oor. If the cabinet is not

secured, it may increase noise when the dishwasher is operating.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 9DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 9 2023-05-03  11:50:022023-05-03  11:50:02

Installation

English10

If this is a new installation, follow these steps:

1. Using a 2

1

/

2

inch hole saw, cut a hole into the side of the cabinet that holds the sink as

shown in Figure 1-1 below.

2. If the base inside the sink cabinet is raised above the kitchen oor and is higher than the

connections on the dishwasher, make a hole in the base inside the cabinet and in the cabinet

side as shown in Figure 1-2.

NOTE

Depending on where your electrical outlet is, you may need to cut a hole in the opposite

cabinet side.

Figure 1-1

The hole for the water supply line, drain

hose and power cables.

Figure 1-2

CAUTION

Make sure the edges of the cabinet hole are smooth before you insert the drain hose

through the hole. Sharp edges from the cabinet hole may cause damage to the drain hose,

resulting in a leak from the hose.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 10DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 10 2023-05-03  11:50:022023-05-03  11:50:02

English 11

Installation

Product dimensions

Front view

DW80CB5450****

DW80CG5450****, DW80CG5420****, DW80CG5020****

DW80CG5451****

Junction box

23

7

/

8

" (605 mm)

23

7

/

8

" (605 mm)

23

7

/

8

" (605 mm)

33⅞-35" (860-890 mm)

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 11DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 11 2023-05-03  11:50:022023-05-03  11:50:02

Installation

English12

Cabinet dimensions

24" (610 mm) minimum

34⅛-35⅓" (867-897 mm)

24" (610 mm)

minimum

NOTE

This dishwasher is designed to be enclosed

on the top and on both sides by a standard

residential kitchen cabinet unit.

The installation cabinet must be clean and

free of any obstructions.

The cabinet must be at least 24 inches wide,

24 inches deep, and 341/8 inches high.

For the front door of the dishwasher to be

ush with the leading edge of the counter

top, the counter top must be at least

25 inches deep.

DW80CB5450****, DW80CG5450****

DW80CG5420****, DW80CG5020****

DW80CG5451****

Side view

27

5

/

16

" (693 mm)

20

1

/

2

" (520 mm)

2

3

/

4

" (70 mm)

56 mm

135 mm

207 mm

20

1

/

2

" (520 mm)

25" (636 mm)

4

1

/

3

" (107 mm)

You must arrange the

water supply line,

power cable and drain

hose in the space

behind the dishwasher.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 12DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 12 2023-05-03  11:50:022023-05-03  11:50:02

English 13

Installation

STEP 3 Check water supply requirements and cautions

• The hot water supply line pressure must be between 20~120 psi (140~830 kPa).

• Adjust the water heater to deliver water between 120 °F (49 °C)~149 °F (65 °C).

- The dishwasher must be connected to a hot water supply between 120 °F

(49 °C)~149 °F (65 °C). This temperature range provides the best washing result

and shortest cycle time. Temperature should not exceed 149 °F (65 °C) to prevent

damage to dishes.

- Ensure that the water supply valve is turned off before connecting the hot water

supply line to the dishwasher.

- Seal the hot water supply line connections using teon tape or sealing compound to

stop any water leakage.

- The drain hose connected to the dishwasher must be run through the hole in the

side wall so it can be connected to the drain outlet of the sink. When you install the

dishwasher, ensure there is nothing on the drain hose and be careful not to damage

it during the installation process.

Figure 2

Dishwasher bottom

Hot Water

Supply Line

4

1

/

4

-6

1

/

4

in.

(110-160 mm)

Power cable

Inlet valve

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 13DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 13 2023-05-03  11:50:032023-05-03  11:50:03

Installation

English14

STEP 4 Check the electrical requirements and cautions

The electrical requirements for the dishwasher are as follows:

• In the United States, install in accordance with the National Electric Code/State and

Municipal codes and/or local codes.

• In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/

Provincial and Municipal codes and/or local codes.

• For cable direct connections.

- Use exible, armored or non-metallic sheathed, copper wire with a grounding wire

that meets the wiring requirements for your local codes and ordinances.

- Use the strain relief method provided with the wiring junction box or install a U.L.-

listed/CSA-certied clamp connector to the wiring junction box. If using conduit, use

a U.L.-listed/CSA-certied conduit connector.

Figure 3

Dishwasher bottom

Hot Water

Supply Line

Power cable

2

1

/

2

-3

1

/

2

in.

(64-89 mm)

Power cable channel

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 14DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 14 2023-05-03  11:50:032023-05-03  11:50:03

English 15

Installation

STEP 5 Unpacking and inspecting the dishwasher

Unpack the dishwasher in an open area free of obstruction both around the packaging

and overhead. We recommend that you retain all of the packing materials until the

dishwasher is fully installed and operational to ensure you have removed all the product’s

components from the packing materials prior to disposal.

Unpacking

1. Position the carton right-side-up with

top arrows pointing upwards.

2. Unbuckle or cut the straps securing the

packaging.

3. Unpack the product packaging with

care.

4. Put the straps and all of the packing

materials from around the dishwasher

inspecting them for any signs of

damage.

5. Locate and set aside the dishwasher's

kick plate. The Kick plate is attached to

packing material of the dishwasher.

Kick plate

6. Lift the dishwasher from the packing tray, and then place it on the oor.

CAUTION

• ALWAYS LIFT THE DISHWASHER TO MOVE IT. Sliding it over rough surfaces can

damage the dishwasher’s feet and sliding the feet over nished surfaces can, in some

cases, damage that nish or the underlying surface.

7. There is also packing inside the dishwasher that you may want to leave in place until

the dishwasher is installed.

8. DO NOT, under any circumstances, remove the sound-absorbent padding that

surrounds the exterior of the tub of the dishwasher.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 15DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 15 2023-05-03  11:50:032023-05-03  11:50:03

Installation

English16

Inspecting

Mechanical

1. Check the plastic base assembly to ensure that it is intact

2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can

level and secure the dishwasher.

3. Check all the visible components on the bottom of the dishwasher to ensure they are

intact and secure.

4. Check the door latch, the operation of the hinges, and conrm the door is properly

secured to the dishwasher.

Plumbing

1. Check the hot water connection on the back left-side of the base of the dishwasher.

The mounting plate should be secured to the back of the base, the threads inside the

connection should be smooth and shiny, and the area should be clean and free of any

debris.

2. Make sure the dishwasher and the accessories are all included in the package to ensure

these assemblies are not cracked and that all connections are secure.

3. Check the drain hose for any holes or deformities that could allow a water leak during

draining.

Electrical

1. Conrm the junction box cover is secured to the junction box on the front right-side of

the base of the dishwasher.

2. Conrm the electrical box was not damaged during shipping and that it is secured to

the base of the dishwasher.

Appearance

1. Conrm there are no dents or scratches on the front of the dishwasher.

2. Check the edges of the doors for any roughness or cracking.

3. Check the control panel to ensure it is clear and unscratched, and that all the control

markers are in their proper places.

Parts

Conrm you have all the parts listed in STEP 1 on page 6.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 16DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 16 2023-05-03  11:50:032023-05-03  11:50:03

English 17

Installation

STEP 6 Mounting the Bespoke panel (applicable models only)

1. Open the door and t the Bespoke

panel in the front bottom of the door.

Make sure that the ribs of the panel t

into the corresponding holes (totaling 6)

of the door.

2. While holding the door and the

Bespoke panel with both hands, press

the panel evenly from bottom to top to

lock into the dishwasher.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 17DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 17 2023-05-03  11:50:032023-05-03  11:50:03

Installation

English18

3. When both sides of the panel lock

into place, press the top center of the

Bespoke panel to secure it to the top of

the door.

NOTE

• Make sure that the Bespoke panel ts in

the dishwasher properly.

• If the gap between the dishwasher

and the Bespoke panel is below 2 mm,

proper installation is done. For 2 mm or

more, remove the Bespoke panel and

try again.

4. Unpack the caps and screws (two for

each) included in the product package.

5. Tighten the screws on either side of the

dishwasher.

NOTE

When tightening the screw on either side,

make sure to check the gap between either

side as the Bespoke door may lean in

either side.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 18DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 18 2023-05-03  11:50:032023-05-03  11:50:03

English 19

Installation

NOTE

After inserting the panel, check it with

bare eyes.

If the panel is not correctly inserted, or

the gaps are not even in all four corners,

reinstall the panel.

Reinstallation

Remove the screws on both sides of the

door. Then, put the suction cups on the

panel, one in the top left area of the panel

and the other in the top right. Pull up the

handles of the suction cups to remove the

panel, then install the panel again.

CAUTION

• Using the cups in the center area may

bend the panel. Make sure to put the

suction cups in the top left and top right

areas of the panel. Then, pull up the

handle just once for each.

• Make sure the door is secured and

stable before using the suction cups.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 19DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 19 2023-05-03  11:50:032023-05-03  11:50:03

Installation

English20

6. Insert the caps on either side. Make

sure the rib of the cap ts in the hole of

the dishwasher in the right direction.

7. This is the completion of mounting the

Bespoke panel.

CAUTION

Any third-party panel other than Samsung’s Bespoke panel (available in Samsung

authorized retailers) is not allowed for attachment. The customer is responsible for any

problem resulting from such a third-party panel.

DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 20DW5000C_DW80CB507012AA_DD68-00260A-00_EN.indd 20 2023-05-03  11:50:042023-05-03  11:50:04

La page charge ...

Yes DW80CG5450MT Guide d'installation

Ce manuel convient également à

Yes DW80CG5450MT Guide d'installation

dans d''autres langues

Autres documents