Wyze BC1 Wired smart door bell camera security Manuel utilisateur

Wyze
Marque
Wyze
Modèle
BC1 Wired smart door bell camera security
Taper
Manuel utilisateur
WDBC1-KSZP01 V1.0
WDBC1-KSZP01 V1.0
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates uses and can
radiate radio frequency energy and, if
This device complies with ISEDC
licence-exempt RSS standard (s).
Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference,including
interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux
CNR d'ISEDC applicables aux appareils
radio exempts de licence.
L'exploitation est autorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de
brouillage, et
(2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique
subi, même si le brouillage est
susceptible d'en compromettre le
fonctionnement.
ISEDC Radiation Exposure Statement:
This equipment complies with ISEDC
RF radiation exposure limits set forth
for an uncontrolled environment. This
transmitter must not be co-located or
operating in conjunction with any other
Any Changes or modifications not
expressly approved by the party
responsible for compliance
could void the user’s authority to
operate the equipment.
antenna or transmitter.
Cet appareil est
conforme aux limitesd'exposition de
rayonnement RF ISEDC établiespour
un environnement non contrôlé.
Cetémetteur ne doit pas être
co-implanté oufonctionner en
conjonction avec toute autreantenne
ou transmetteur.
FCC Statement
ISEDC RSS Warning
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to try
to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving
antenna.
-- Increase the separation between the
equipment and receiver.
-- Connect the equipment into an
outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced
radio/TV technician for help
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions (1)this device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Resources & Support
support.wyze.com
Community
forums.wyze.com
NEED HELP?
Scan the QR code
to learn more
13
7
8
1412
9 10 11
2
back
front
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment .
This transmitter must not be co‐located or
operating in conjunction with any other
antenna or transmitter.
13
QUICK START GUIDE
Wyze Chime
IN THE BOX
Wyze Chime
Quick Start Guide
x 1
x 1
1Insert Wyze Sensor Bridge into
the USB port of a Wyze Cam or
Wyze Cam Pan and wait for the
Status Light to turn solid blue.
Notice: 1. Wyze Chime can only connect
to Wyze Sensor Bridge (included in Wyze
Sense Starter Kit) which is connected to
Wyze Cam or Wyze Cam Pan.
2. Wyze Chime can also connect to Wyze
Video Doorbell. Please refer to the Wyze
Video Doorbell manual for details. Notice:Wyze Sensor Bridge is not included.
SETUP
1Setup Button
2Status Light
3Speaker Wyze Cam Wyze Cam pan
Wyze Sensor Bridge
13
2
Solid blue light
Successful connection
Flashing blue light
On connection
Solid yellow light
Unconnected
LIGHT INDICATIONS
2Insert Wyze Chime into an
outlet.
3Open the Wyze app and tap the 3
dots on the top right corner of the
Home Page. Select “Add a Product”
and then select Wyze Chime.
Follow the instructions in the
Wyze app to finish setup.
4Connect multiple Wyze Chime
devices, please repeat the steps 3.
6
45
  • Page 1 1

Wyze BC1 Wired smart door bell camera security Manuel utilisateur

Wyze
Marque
Wyze
Modèle
BC1 Wired smart door bell camera security
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents