INSTALLATION INSTRUCTIONS
Large Bolt Down Table Stand
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LDB1U
LDB1U Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to mounting system does not
exceed 125 lbs (56.7 kg). Use with heavier televisions may
result in instability causing tip over resulting in death or
serious injury!
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mounting system outdoors.
NOTE: The LDB1U mount has no user serviceable parts.
IMPORTANT ! :
The LDB1U
mounting system
is designed to
be mounted to a desk with a maximum thickness of 1 1/2".
--SAVE THESE INSTRUCTIONS--
Installation Instructions LDB1U
3
DIMENSIONS
LDB1U Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions LDB1U
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
5/16" (7.9mm)
#2
5/32" (included)
3/16" (included) 3/16 x 10" (included)
R (1)
[Table stand]
S (1)
[Table stand interface] T (1)
[Left interface] U (1)
[Right interface]
AA (1)
[Clamping plate]
W (4)
1/4-20 x 1/2" X (1)
[Cable port cover]
Y (1)
3/16"
BB (3)
1/4-20 x 2 1/2" CC (3)
1/4"
C (4) E (4)
A (4)
M4x12mm B (4)
M4x20mm M4x25mm D (4)
M5x12mm M5x20mm F (4)
M5x25mm G (4)
M6x12mm H (4)
M6x20mm
Universal Hardware Kit
I (4)
M6x25mm K (4)
J (4)
M8x12mm M8x20mm L (4)
M8x30mm M (8)
[Nesting
N (4)
[Universal
spacer]
[Included in hardware box]
V (1)
#10-24 x 1/2"
(security) (security)
washer]
P (2)
3/4-16 x 3/4"
Q (1)
3/16 x 10"
Z (1)
5/32"
LDB1U Installation Instructions
6
Assembly And Installation
Display Enclosure Assembly
1. Loosely install two 1/4-20 x 1/2" button head security
screws (W) into top holes on table stand (R). (See Figure 1)
2. Hang table stand interface (S) over two partially installed
screws. Use upper holes for higher installation or lower
holes for lower installation. (See Figure 1)
3. Use two 1/4-20 x 1/2" button head security screws (W) to
secure table stand interface (S) to table stand (R). (See
Figure 1)
4. Tighten all four screws.
Figure 1
5. Determine mounting location by setting table stand on desk
and experimenting with desired rotation capabilities.
NOTE: Rotation radius can be set to be either +/- 15 or 30 .
See Dimensions graphic for details.
6. Use clamping plate (AA) as a template to mark locations for
the three holes to be drilled at desired mounting location.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! The mounting surface must be a
minimum of 3/4" in depth for medium-density fibreboard or
particle board. If mounting to another type of surface, make
sure surface can hold up to four times the combined weight of
all equipment prior to mounting the LDB1U to surface!
7. Drill three 5/16" holes at locations marked in Step 3. (See
Figure 2)
NOTE: If cables are going to be routed through the table, an
additional hole needs to be drilled in center of clamping
plate (A). See Cable Management Section for details.
8. (Optional) If cables are going to be routed through the desk,
drill an additional hole in the center of the clamping plate
that is large enough to account for all cables that will be
routed through the desk. (See Figure 2)
NOTE: One hole should be centered at the front of the mount.
Figure 2
9. Lift base cover up to expose mounting holes on table stand
(R). (See Figure 3)
10. Use three 1/4-20 x 2 1/2" tapping bolts (BB), three 1/4"
washers (CC) and clamping plate (AA) to secure table stand
(R) to table. (See Figure 3)
Figure 3
1
(W) x 2
(R)
(S)
2
(W) x 2
3
upper
holes
lower
holes
(lower installation shown)
x 3
front of mount
6
7
x 3
8
(AA)
9
(BB) x 3
10
(AA)
desk
(CC) x 3
Installation Instructions LDB1U
7
11. Use #10-24 x 1/2" security screw (V) to secure table stand
cover to table stand (R). (See Figure 4)
Figure 4
NOTE: Prior to installing display, the rotation radius should be
adjusted. Once the display is connected, it will no
longer be possible to adjust the rotational stop without
removing the display from the mount.
12. Use the 5/32" security hex key (Z) to loosen rotational stop
adjustment screw until desired radius is achieved. (See
Figure 5)
WARNING: TO REDUCE THE RISK OF BURNS, FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS, rotational
stop must be in place prior to display installation! If stop is not
in place, the cables may be damaged if the display is over-
rotated! Always make sure rotational stop is in place before
proceeding with installation!
Figure 5
Attaching Interface Brackets to Screen
1. Align the center of the bracket (T and U) with center of
screen. (See Figure 6)
NOTE: The diamond-shape holes in the bracket correspond to
the center of the mount.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2. Select correct screws, nesting spacers (if necessary) and
universal washers (if required) from the hardware bag (A-N)
and attach brackets to back of screen. (See Figure 6)
Figure 6
IMPORTANT ! : The M8 screws do NOT require a
washer. Use the universal washer (N) only with M4, M5
and M6 screws.
NOTE: The nesting spacers (M) may be used separately, or
put two together in different configurations to create
different size spacers. (See Figure 7)
Figure 7
(V)
11
table stand cover
(view from beneath)
rotational stop
adjustment screw
15
30
rotation
radius's
Center of bracket
Pull cord
[Brackets T and U
(M) (N)
(A-L)
NOTE: Use universal washer (N) ONLY with M4, M5
and M6 screws.
shown]
(Single) (Nested) (Stacked)
0.375
[9.5] 0.563
[14.3] 0.750
[19.1]
LDB1U Installation Instructions
8
Attaching Screen to Mount
IMPORTANT ! : Position screen in a centered position on
rails.
NOTE: NEVER place both interface brackets (T and U) to one
side of the wall mount center line! (See Figure 8)
Figure 8
1. Hang screen onto the top rail of the table stand interface (S).
(See Figure 9)
•Hang top hook of interface brackets (T and U) onto the
top rail of the table stand interface (S). (See Figure 9)
NOTE: The screen initially installs into the "service mode" to
allow easy cable access.
2. Adjust screen and rails to desired viewing position.
3. Route cables between wall and rails.
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
4. Pull downward on the pull cords and swing inward toward
wall, latching interface brackets to lower rail and fastening
bottom of screen to the mount. (See Figure 9)
5. Attach end of pull cord (a magnet) to mount so it does not
extend beyond bottom of screen. (See Figure 9)
Figure 9
Locking Screen Interface Brackets (Optional)
1. Lock screen interface brackets onto mount rails using one
3/8-16 x 3/4" set screw (P) on each interface bracket. (See
Figure 10)
Figure 10
NEVER place both interface brackets to one
side of the wall mount center line (CL)!
Center Line (CL)
[Brackets T and U shown]
5
Pull
1
Top
Hook
cords
4
4
1
(P) x 2
Installation Instructions LDB1U
9
Locking Mount (Optional)
1. Add padlock (not included) to interface bracket to complete
security. (See Figure 11)
NOTE: The padlock maximum shackle diameter is 5/16"
(7.9 mm).
Figure 11
Additional Mount Safety
If LDS1U is mounted to a table in a high traffic area, it is
recommended that a safety strap be used for additional
security. UL-listed ELM701 Anti-tip Strap from Sanus® may be
purchased separately.
1
Padlock shackle
- 5/16" (7.9mm)
maximum diameter:
LDB1U Installation Instructions
10
Installation Instructions LDB1U
11
LDB1U Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-003014 Rev00
2018 Milestone AV Technologies
www.milestone.com
03/18
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
dans d''autres langues
- English: Chief LDB1U Installation guide
Documents connexes
-
Chief XCB1U Guide d'installation
-
Chief XCM1U Manuel utilisateur
-
-
Chief LCM1U Guide d'installation
-
-
-
-
-
-