NISBETS DC439-A Manuel utilisateur

Taper
Manuel utilisateur
Ice maker
Instruction manual
Model:
DC439-A
2
AU Telephone Helpline: 1300225960
Safety Instructions
Position on a flat, stable surface.
A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components on this product.
Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- Fire Precautions
- Wiring Regulations
- Building Regulations
DO NOT immerse in water, or use steam/jet washers to
clean the unit.
DO NOT cover the appliance when it is operating.
Always carry, store and handle the appliance in a vertical
position.
ONLY use drinking or potable water when making ice cubes.
Replace any unused water in the tank at least once every 24
hours.
Keep all packaging away from children. Dispose of the
packaging in accordance to the regulations of local
authorities.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
3
AU Telephone Helpline: 1300225960
If the power cord is damaged, it must be replaced by a
Nisbets Essentials agent or a recommended qualified
technician in order to avoid a hazard.
Nisbets Essentials recommend that this appliance should
be periodically tested (at least annually) by a Competent
Person. Testing should include, but not be limited to: Visual
Inspection, Polarity Test, Earth Continuity, Insulation
Continuity and Functional Testing.
The appliance is intended to be used in household and
similar applications.
Warning: Risk of fire / flammable materials
Do not store explosive substances such as aerosol cans with
a flammable propellant in this appliance.
Warning: Keep all ventilation openings clear of
obstruction. Unit should not be boxed in without
adequate ventilation.
Warning: Do not use mechanical devices or other means
to accelerate the defrosting process, other than those
recommended by the manufacturer.
Warning: Do not damage the refrigerant circuit.
Warning: Do not use electrical appliances inside the food
storage compartments of the appliance, unless they are the
type recommended by the manufacturer.
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of this
machine will provide the best possible performance from your Nisbets Essentials product.
4
AU Telephone Helpline: 1300225960
Pack Contents
The following is included:
Ice Maker
Removable ice basket
Ice scoop
Instruction manual
Nisbets Essentials prides itself on quality and service,
ensuring that at the time of packaging the contents
are supplied fully functional and free of damage.
Should you find any damage as a result of transit,
please contact your Nisbets Essentials dealer
immediately.
Installation
Note: If the unit has not been stored
or moved in an upright position, let
it stand upright for approximately 12
hours before operation. If in doubt
allow to stand.
1. Remove the appliance from the packaging and
the protective film from all surfaces.
2. To optimize performance and longevity, ensure
a minimum clearance of 2.5cm is maintained
between the unit and walls and other objects,
with a minimum 5cm clearance on the top.
NEVER LOCATE NEXT TO A HEAT SOURCE.
WARNING: When positioning the appliance,
ensure the supply cord is not trapped or damaged.
WARNING: Do not locate multiple portable
socket-outlets or portable power supplies at the
rear of the appliance.
Operation
Control Panel
SMALL ice cube
indicator
ADD WATER indicator
ICE FULL indicator
POWER button
SELECT button
CLEAN button
LARGE ice tube indicator
Making Ice
Note: Before using for the first time,
clean the water tank, ice basket
and ice basket shelf. Use the first
3 ice making cycle to flush out the
system. Discard the water and ice
created from the first 3 cycles.
Each time the appliance is refilled, the first ice making
cycle is used to reduce the water temperature.
This results in uneven ice cube production which is
perfectly normal. You may wish to discard ice created
in the first two production cycles.
1. Lift the access lid and fill the water tank up the
level of the ice basket shelf.
2. Connect the appliance to the power and press
the “POWER” button.
3. Press the “SELECT” button repeatedly to scroll
through the ice cube sizes. Stop when the
required size is illuminated.
Note: The ice making cycle will
vary depending on the size of cube
selected. Larger cubes will take
longer to produce.
4. The appliance will run a start-up routine and then
begin ice production.
Note: If the water level is too low,
the ADD WATER indicator lights up
and the appliance stops working. Fill
the water tank and the appliance will
restart automatically.
5. When the cubes reach the ice sensor the
appliance will stop production. Production
resumes once ice has been removed.
Cleaning, Care &
Maintenance
Always switch off and disconnect the power
supply before cleaning.
Warm, soapy water is recommended for cleaning.
Cleaning agents may leave harmful residues.
DO NOT wash the base unit, instead wipe the
exterior with a damp cloth.
5
AU Telephone Helpline: 1300225960
A Nisbets Essentials agent or qualified technician should carry out repairs if required.
Clean the water filter regularly with a small brush, particularly in hard water areas. The water filter is
located in the pump inlet at the bottom of the water tank, remove by pulling out with fingers.
If the appliance is to be left unused for longer than 24 hours, loosen the drain screw and drain the water
from the tank.
The inner removable parts and water tank should be cleaned regularly.
Automatic cleaning
Remove the ice basket. Then add dilute cleaner into the water tank. Note: Choose ice maker specific
cleaner and follow the manufacturer’s instructions.
Press the “CLEAN” button. The “CLEAN” indicator flashes and auto cleaning cycle starts. After auto-
cleaning done, the “CLEAN” indicator will go out.
Turn the unit off and disconnect from power supply. Loosen the drain screw to drain the solution.
Note: After auto-cleaning, use the first 3 ice making cycles to flush out the system. Discard the water
and ice created from these initial cycles.
Troubleshooting
If your Nisbets Essentials appliance develops a fault, please check the following table before making a call to
the Helpline or your Nisbets Essentials dealer.
Fault Probable Cause Solution
The appliance is not
working
The unit is not switched on Check the unit is plugged in correctly and
switched on
Plug or lead is damaged Call Nisbets Essentials agent or qualified
Technician
Power supply Check power supply
Appliance is noisy or
works intermittently
Power fluctuations Turn off the ice maker and restart after 3
minutes
Add Water
indicator is lit
Water level is low or tank is empty Refill water tank and restart
Water filter is blocked Clean water filter and restart appliance
Ice Full
indicator is lit
Ice basket full Empty the ice basket
All indicators flash
simultaneously
Water box is blocked by ice Disconnect from the power supply.
Remove some of the ice cubes and gently
tilt the water box by hand. Restart the
appliance after 3 minutes. If the unit fails to
work after above operations, call Nisbets
Essentials agent or qualified Technician
The motor stops working suddenly
Ice cubes are sticking
together
Ice making cycle is too long Reset the ice cube size and restart the
appliance
Water tank temperature is too low Empty water tank and refill
Compressor runs but no
ice is made
Refrigerant leak or block in the
refrigerant system
Call Nisbets Essentials agent or qualified
technician
6
AU Telephone Helpline: 1300225960
Technical Specifications
Model Voltage Power Bin
Storage
Max. Ice Making
Capacity Refrigerant Dimensions
H x W x D mm Weight
DC439-A 220-240V~
50Hz
150W 0.7kg 20kg/24 hours R600a 327 x 270 x 365 10.6kg
Electrical Wiring
The plug is to be connected to a suitable mains socket.
Nisbets Essentials appliances are wired as follows:
Live wire (coloured brown) to terminal marked L
Neutral wire (coloured blue) to terminal marked N
Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection
being required they must be readily accessible.
Compliance
The product must not be disposed of as household waste. To help prevent possible harm to human health
and/or the environment, the product must be disposed of in an approved and environmentally safe recycling
process. For further information on how to dispose of this product correctly, contact the product supplier, or
the local authority responsible for waste disposal in your area.
Nisbets Essentials parts have undergone strict product testing in order to comply with
regulatory standards and specifications set by international, independent, and federal
authorities.
Nisbets Essentials products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without the prior written permission of Nisbets Essentials.
Every effort is made to ensure all details are correct at the time of going to press, however, Nisbets Essentials reserve the right to change
specifications without notice.
DECLARATION OF CONFORMITY
Conformiteitsverklaring Déclaration de conformité Konformitätserklärung Dichiarazione di conformità
Declaración de conformidad Declaração de conformidade
Equipment Type Uitrustingstype • Type d'équipement Gerätetyp
Tipo di apparecchiatura Tipo de equipo Tipo de equipamento
Model Modèle Modell Modello
Modelo Malli
Ice maker - 20kg
DC439 (& -E -A)
Council Directives(s)
Toepassing van Europese Richtlijn(en) •
Application de la/des directive(s) du
Conseil Anwendbare EU-Richtlinie(n)
Applicazione delle Direttive
• Aplicación de la(s) directiva(s) del
consejo Aplicação de directiva(s) do
Conselho
Low Voltage Directive (LVD) - 2014/35/EU
Electrical Equipment (Safety) Regulations 2016
EN 60335-1:2012 +A11:2014 +A13:2017 +A1:2019
+A14:2019 +A2:2019
EN 60335-2-24:2010 +A1:2019 +A2:2019
EN 62233:2008
Electro-Magnetic Compatibility (EMC) Directive
2014/30/EU - recast of 2004/108/EC
Electromagnetic Compatibility Regulations 2016
(S.I. 2016/1091)
EN 55014-1:2017 +A11:2020
EN 55014-2: 2015
EN IEC 61000-3-2: 2019
EN 61000-3-3: 2013 +A1:2019
Restriction of Hazardous Substances Directive
(RoHS) 2015/863 amending Annex II to Directive
2011/65/EU
Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronic
Equipment Regulations 2012 (S.I. 2012/3032)
Electrical Safety
IEC 60335-1:2010 +A1:2012 +A2:2017
IEC 60335-2-24:2010 +A1:2012 +A2:2016
Electromagnetic Compatibility
EN 55014-1:2017 +A11:2020
EN 55014-2: 2015
EN IEC 61000-3-2: 2019
EN 61000-3-3: 2013 +A1:2019
Producer Name Naam fabrikant Nom du producteur Name des Herstellers
Nome del produttore Nombre del fabricante Nome do fabricante
Nisbets Essentials
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and
Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande Richtlijn(en)
en Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und Norm(en)
entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y estándar(es) arriba
mencionadas.
Eu, o abaixo-assinado, declaro que o equipamento anteriormente especificado está em conformidade com a(s) anterior(es) Directiva(s) e
Norma(s)
Date • Data • Date • Datum • Data
Fecha • Data
7th September 2021
Signature Handtekening • Signature •
Unterschrift Firma • Firma • Assinatura
Full Name Volledige naam • Nom et
prénom Vollständiger Name • Nome
completo Nombre completo Nome
por extenso
Ashley Hooper
Eoghan Donnellan
Nerida Pearse
Position Functie Fonction • Position
Qualifica Posición Função
Technical & Quality
Manager
Commercial Manager/
Importer
Commercial Manager/ Responsible
Supplier
Producer Address Adres fabrikant
Adresse du producteur Anschrift des
Herstellers Indirizzo del produttore
Dirección del fabricante • Morada do
fabricante
Fourth Way,
Avonmouth,
Bristol,
BS11 8TB
United Kingdom
42 North Point
Business Park
New Mallow Road
Cork
Ireland
15 Bagdally Road,
Campbelltown
NSW 2560
DocuSign Envelope ID: 178D37D3-6351-43F1-8911-2713EC3D80C3
DC439-A_A5_v1_20210909
http://www.nisbets.com/
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

NISBETS DC439-A Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues