HTZ750
EN Operator's manual 2-16
ES-MX Manual de usuario 17-34
FR-CA Manuel d’utilisation 35-51
Contents
Introduction..................................................................... 2
Safety..............................................................................3
Operation........................................................................ 7
Maintenance................................................................... 9
Troubleshooting............................................................ 12
Transportation, storage and disposal........................... 13
Technical data.............................................................. 14
Warranty....................................................................... 15
Introduction
Product overview
1
19
10
8
2
313
4
5
21
22
16
14
9
11
15
18
17
7
6
20
12
23
1. Operator's manual
2. Fuel tank cap
3. Fuel tank
4. Choke control
5. Air purge bulb
6. Spark plug cap and spark plug
7. Front handle
8. Stop switch
9. Throttle trigger lockout
10. Throttle trigger
11. Rear handle
12. Blade
13. Air filter cover
14. Gear housing
15. Grease nipple
16. Starter rope handle
17. Cylinder cover
18. Hand guard
19. Transport guard
20. Leaf catcher
21. Combination wrench
22. Tube of grease
23. Blade tip protection
Product description
The product is a hedge trimmer with a combustion
engine.
Intended use
Use the product to cut branches and twigs. Do not use
the product for other tasks.
21075 - 003 - 30.01.2021
Symbols on the product
WARNING! This product is dangerous.
Injury or death can occur to the operator
or bystanders if the product is not used
carefully and correctly. To prevent injury
to the operator or bystanders, read and
obey all safety instructions in the
operator's manual.
Read the operator's manual carefully and
make sure that you understand the
instructions before use.
Use approved hearing protection and
approved eye protection.
Use approved protective gloves.
Use heavy-duty slip-resistant boots.
yyyywwxxxx The rating plate shows serial number.
yyyy is the production year and ww is
the production week.
Note: Other symbols/decals on the product refer to
certification requirements for some markets.
California Proposition 65
WARNING!
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects or other
reproductive harm.
EPA III
The Emissions Compliance Period referred to on the
Emission Compliance label indicates the number of
operating hours for which the engine has been shown to
meet Federal and California emissions requirements.
Customer assistance
For customer assistance, call: 1-800-291-8251 or visit
www.RedMax.com.
Safety
Safety definitions
Warnings, cautions and notes are used to point out
specially important parts of the manual.
WARNING: Used if there is a risk of
injury or death for the operator or bystanders
if the instructions in the manual are not
obeyed.
CAUTION: Used if there is a risk of
damage to the product, other materials or
the adjacent area if the instructions in the
manual are not obeyed.
Note: Used to give more information that is necessary
in a given situation.
General safety instructions
WARNING: Read the warning
instructions that follow before you use the
product.
• Incorrect or careless use of the product can turn it
into a dangerous tool that can cause serious or even
fatal injury. It is extremely important that you read
and understand the contents of this operator’s
manual.
• This product produces an electromagnetic field
during operation. This field may under some
circumstances interfere with active or passive
medical implants. To reduce the risk of serious or
fatal injury, we recommend persons with medical
implants to consult their physician and the medical
implant manufacturer before operating this product.
1075 - 003 - 30.01.2021 3
• Overexposure to vibration can lead to circulatory
damage or nerve damage in people who have
impaired circulation. Contact your doctor if you
experience symptoms of overexposure to vibration.
Such symptoms include numbness, loss of feeling,
tingling, pricking, pain, loss of strength, changes in
skin color or condition. These symptoms normally
appear in the fingers, hands or wrists. The risk
increases at low temperatures.
• If you encounter a situation where you are uncertain
how to proceed you should ask an expert. Contact
your dealer or your service workshop. Avoid all
usage which you consider to be beyond your
capability.
• Keep in mind that the operator is responsible for
accidents or hazards occurring to other people or
their property.
• Never allow anyone else to use the product without
first ensuring that they have understood the contents
of the operator’s manual.
• Never allow children to use or be in the vicinity of the
product. As the product is equipped with a spring-
loaded stop switch and can be started by low speed
and force on the starter handle, even small children
under some circumstances can produce the force
necessary to start the product. This can mean a risk
of serious personal injury. Therefore remove the
spark plug cap when the product is not under close
supervision.
• Store the product out of reach of children.
• Never use the product if you are tired, if you have
drunk alcohol, or if you are taking medication that
could affect your vision, your judgement or your
coordination.
• Never use a product that is faulty. Carry out the
checks, maintenance and service instructions
described in this manual. Some maintenance and
service measures must be carried out by trained and
qualified specialists. Refer to instructions under the
heading Maintenance.
• Never use a product that has been modified in any
way from its original specification.
Safety instructions for operation
WARNING: Read the warning
instructions that follow before you use the
product.
• Never use the product in extreme weather conditions
such as severe cold, very hot and/or humid climates.
• Faulty blades can increase the risk of accidents.
• Ensure that no-one comes closer than 15 m / 50 ft
while you are working.
• Observe your surroundings and make sure that there
is no risk of people or animals coming into contact
with the cutting equipment.
• Inspect the working area. Remove any objects that
could be thrown out.
• Always ensure you have a safe and stable working
position.
• Never leave the product unsupervised with the motor
running.
• Make sure that your hands and feet do not come
near the cutting unit when the engine is running.
• If anything jams in the blades while you are working,
switch off the engine and wait until it has stopped
completely before cleaning the blades. Disconnect
the HT lead from the spark plug. Refer to
To
examine the blades on page 12
.
• When the engine is switched off, keep your hands
and feet away from the cutting unit until it has
stopped completely.
• Watch out for stumps of branches that can be thrown
out during cutting.
• Listen out for warning signals or shouts when you
are wearing hearing protection. Always remove your
hearing protection as soon as the engine stops.
• Never work from a ladder, stool or any other raised
position that is not fully secured.
• Always use both hands to hold the product. Hold the
product in front of your body.
• If any foreign object is hit or if vibrations occur stop
the product immediately. Disconnect the HT lead
from the spark plug. Check that the product is not
damaged. Repair any damage.
• Ensure that the spark plug cap and ignition lead are
undamaged to avoid the risk of electric shock.
• Check that all nuts and screws are tight.
• Make sure the gear housing is lubricated correctly.
Refer to
To lubricate the gear housing on page 12
.
• The gear housing gets hot when the product has
been in use. To avoid burning yourself do not touch
the gear housing.
• All covers and guards must be fitted before starting.
• The transport guard should always be fitted to the
cutting unit when the product is not in use.
Personal protective equipment
WARNING: Read the warning
instructions that follow before you use the
product.
• Always use approved personal protective equipment
when you use the product. Personal protective
equipment cannot fully prevent injury but it
decreases the degree of injury if an accident does
occur. Let your dealer help you select the right
equipment.
• Use approved hearing protection that provides
adequate noise reduction. Long-term exposure to
noise can result in permanent hearing impairment.
• Use approved eye protection. If you use a visor, you
must also use approved protective goggles.
Approved protective goggles must comply with the
41075 - 003 - 30.01.2021
ANSI Z87.1 standard in the USAs or EN 166 in EU
countries.
• Use gloves when necessary, for example when you
attach, examine or clean the cutting equipment.
• Use sturdy non-slip boots or shoes.
• Use clothing made of a strong fabric. Always use
heavy, long pants and long sleeves. Do not use
loose clothing that can catch on twigs and branches.
Do not wear jewelry, short pants, sandals or go with
bare feet. Put your hair up safely above shoulder
level.
• Keep first aid equipment close at hand.
Safety devices on the product
WARNING: Read the warning
instructions that follow before you use the
product.
• Do not use a product with defective safety devices.
• Do a check of the safety devices regularly. If the
safety devices are defective, speak to your Redmax
service agent.
To do a check of the throttle trigger lockout
1. Make sure that the throttle trigger lockout (A) and
throttle trigger (B) move freely and that the return
spring works correctly.
A
B
2. Push down the throttle trigger lockout and make sure
that it goes back to its initial position when you
release it.
3. Make sure that the throttle trigger is locked at the
idle position when the throttle trigger lockout is
released.
4. Start the product and apply full throttle.
5. Release the throttle trigger and make sure that the
blades stop and stay stationary.
WARNING: If the blades move
when the throttle trigger is in the idle
position, then the carburetor idle speed
1075 - 003 - 30.01.2021 5
must be adjusted. Refer to
To adjust the
idle speed on page 10
.
To do a check of the stop switch
1. Start the engine.
2. Push the stop switch to the stop position and make
sure that the engine stops.
WARNING: The stop switch
automatically goes back to start position. To
prevent accidental start, remove the spark
plug cap from the spark plug when you
assemble or do maintenance on the product.
To do a check of the hand guard
The hand guard prevents injuries from the blades.
1. Stop the engine.
2. Make sure that the hand guard is attached correctly.
3. Examine the hand guard for damages.
To do a check of the vibration damping system
The vibration damping system decreases vibration in the
handles. The vibration damping units operate as a
separation between the product body and the handle
unit.
1. Do a visual check for deformation and damage.
2. Make sure that the vibration damping units are
correctly attached.
To do a check of the muffler
WARNING: Do not operate the product
without a muffler or a defective muffler. A
defective muffler can increase the noise
level and the risk of fire. Do not use the
product without, or with a broken, spark
arrester screen. The spark arrester screen
must be replaced if it is damaged.
WARNING: The mufflers become very
hot during and after operation, also at idle
speed.
CAUTION: If the spark arrester screen
is frequently blocked it can be a sign that
performance of the catalytic converter is
decreased. Turn to your servicing dealer to
examine the muffler. A blocked spark
arrester screen will cause overheating and
result in damage to the cylinder and piston.
WARNING: The inner surfaces of the
muffler contain chemicals that can cause
cancer. Be careful not to touch these
elements if the muffler is damaged.
The muffler keeps the noise levels to a minimum and
points the exhaust fumes away from the operator. A
muffler with a catalytic converter decrease harmful
exhaust gases.
1. Stop the engine.
2. Do a visual check for damage and deformation.
3. Make sure that the muffler is correctly attached to
the product.
4. Clean the spark arrester screen with a wire brush.
To do a check of the blades and blade guard
The outer part of the blades has the function of a blade
guard. The blade guard prevents cut injuries.
1. Stop the engine and make sure that the blades stop.
2. Remove the spark plug cap from the spark plug.
3. Put on protective gloves.
4. Make sure that the blade and blade guard is not
damaged or bent. Always replace a damaged or
bent blade, or a damaged blade guard.
5. Make sure that the screws to the blades and blade
guard are tight.
61075 - 003 - 30.01.2021
Fuel safety
WARNING: Read the warning
instructions that follow before you use the
product.
• Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry.
• If you spill fuel on your clothing, change clothing
immediately.
• Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use soap and water to
remove the fuel.
• Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
• Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
• Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
• Do not smoke near the fuel or the engine.
• Do not put warm objects near the fuel or the engine.
• Do not add the fuel when the engine is on.
• Make sure that the engine is cool before you refuel.
• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
• Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
• Move the product a minimum of 3 m / 10 ft from the
position where you filled the tank before a start.
• Do not fill the fuel tank fully. Heat causes the fuel to
expand. Keep a space at the top of the fuel tank.
Safety instructions for maintenance
WARNING: Read the warning
instructions that follow before you use the
product.
• Stop the engine and make sure that the cutting
equipment stops. Let the product become cool
before you do the maintenance.
• Disconnect the spark plug cap before you do the
maintenance.
• The exhaust fumes from the engine contain carbon
monoxide, an odourless, poisonous and very
dangerous gas that can cause death. Do not run the
product indoors or in closed spaces.
• The exhaust fumes from the engine are hot and can
contain sparks. Do not run the product indoors or
near flammable material.
• Accessories and changes to the product that are not
approved by the manufacturer, can cause serious
injury or death. Do not change the product. Always
use original accessories.
• If the maintenance is not done correctly and
regularly, there is an increased risk of injury and
damage to the product.
• Only do the maintenance as this operator's manual
recommends. Let an approved Redmax service
agent do all other servicing.
• Let an approved Redmax service agent do servicing
on the product regularly.
• Replace damaged, worn or broken parts.
Operation
Introduction
WARNING: Read and understand the
safety chapter before you use the product.
Fuel
This product has a two-stroke engine.
CAUTION: Incorrect type of fuel can
result in engine damage. Use a mixture of
gasoline and two-stroke oil.
Premixed fuel
• Use Redmax premixed alkylate fuel of a good
quality, for best performance and extension of the
engine life. This fuel contains less harmful chemicals
compared to regular fuel, which decreases harmful
exhaust fumes. The quantity of remains after
combustion is lower with this fuel, which keeps the
components of the engine more clean.
To mix fuel
Gasoline
• Use good quality unleaded gasoline with a maximum
of 10% ethanol contents.
CAUTION: Do not use gasoline with
an octane grade less than 90 RON/87
AKI. Use of a lower octane grade can
cause engine knocking, which causes
engine damages.
• We recommend that you use gasoline of a higher
octane grade for work with continuously high rpm.
Two-stroke oil
• For best results and performance use Redmax two-
stroke oil.
1075 - 003 - 30.01.2021 7
• If Redmax two-stroke oil is not available, use a two-
stroke oil of good quality for air-cooled engines.
Speak to your servicing dealer to select the correct
oil.
CAUTION: Do not use two-stroke
oil for water-cooled outboard engines,
also referred to as outboard oil. Do not
use oil for four-stroke engines.
To mix gasoline and two-stroke oil
Gasoline, liter Two-stroke oil,
liter
2% (50:1)
5 0.10
10 0.20
15 0.30
20 0.40
US gallon US fl. oz.
1 2 ½
2 1/2 6 ½
5 12 ⅞
CAUTION: Small errors can influence
the ratio of the mixture drastically when you
mix small quantities of fuel. Measure the
quantity of oil carefully and make sure that
you get the correct mixture.
1. Fill half the quantity of gasoline in a clean container
for fuel.
2. Add the full quantity of oil.
3. Shake the fuel mixture.
4. Add the remaining quantity of gasoline to the
container.
5. Carefully shake the fuel mixture.
CAUTION: Do not mix fuel for more
than 1 month at a time.
To fill the fuel tank
1. Clean the area around the fuel tank cap.
2. Shake the container and make sure that the fuel is
fully mixed.
3. Remove the fuel tank cap and fill the fuel tank.
4. Tighten the fuel tank cap carefully.
5. Move the product 3 m/10 ft or more away from the
refueling area and fuel source before you start the
engine.
Note: To see where the fuel tank is on your product,
refer to
Product overview on page 2
.
To install the leaf catcher and the blade
tip protection
1. Remove the outer 8 nuts from the bolts on the blade.
2. Put the leaf catcher on the 8 bolts. Refer to
Product
overview on page 2
, to see where the leaf catcher is
on the product.
3. Put the blade tip protection on the 2 bolts on the tip
of the blade.
4. Install the 8 nuts to the bolts.
5. Torque the nuts to 7 Nm.
To start the product with a cold engine
1. Pull the choke control to choke position.
81075 - 003 - 30.01.2021
2. Push the air purge bulb approximately 6 times or
until the bulb starts to fill with fuel. It is not necessary
to fill the air purge bulb fully.
3. Hold the body of the product on the ground with your
left hand. Do not step on the product.
4. Pull the starter rope handle slowly with your right
hand until you feel some resistance, then pull the
starter rope handle quickly and with force.
WARNING: Do not wind the starter
rope around your hand.
CAUTION: Do not pull the starter
rope to full extension and do not let go of
the starter rope handle.
5. Continue to pull the starter rope handle until the
engine fires, then push the choke control to its initial
position.
WARNING: The blades move when
the engine starts.
6. Continue to pull the starter rope handle until the
engine starts.
7. Push and release the throttle trigger to set the
engine to idle speed.
8. Push the throttle trigger gradually to increase the
engine speed.
9. Make sure that the engine runs smoothly.
To start the product with a warm engine
1. Hold the body of the product on the ground with your
left hand. Do not step on the product.
2. Pull the starter rope handle slowly with your right
hand until you feel some resistance, then pull the
starter rope handle quickly and with force. Continue
until the engine starts.
Note: For more information about how to start the
product, refer to
To start the product with a cold engine
on page 8
.
To stop the product
• Move the stop switch to the stop position to stop the
engine.
CAUTION: The stop switch
automatically goes back to run position.
To operate the product
1. Start near the ground and move the product up
along the hedge when you cut the sides. Make sure
that the body of the product does not touch the
hedge.
WARNING: Make sure that the
front of the cutting equipment does not
touch the ground.
2. Adjust the speed to align with the work load.
3. Hold the product near your body for a stable work
position.
4. Be careful and operate the product slowly.
Maintenance
Introduction
WARNING: Read and understand the
safety chapter before you do maintenance
on the product.
1075 - 003 - 30.01.2021 9
Maintenance schedule
Maintenance Before
operation
After 40
h
After 100
h
Clean the external surface. After each operation.
Clean the muffler, exhaust pipe and engine from leaves, dirt and unwanted lubri-
cant. After each operation.
Make sure that the cutting attachment does not move at idle speed. X
Do a check of the stop switch, refer to
To do a check of the stop switch on page
6
.X
Examine the cutting attachment and the cutting attachment guard for damages
and cracks. Replace if it is damaged. X
Examine the hand guard for damages and cracks. Replace if it is damaged. X
Do a check of the throttle trigger lockout and the throttle trigger, refer to
To do a
check of the throttle trigger lockout on page 5
.X
Examine the engine, the fuel tank and the fuel lines for leaks. X
Tighten nuts and screws. X
Examine the fuel filter for contamination and the fuel hose for cracks and other
defects. Replace if necessary. X
Examine the starter and the starter rope for damages. X
Clean the air filter. Replace if it is necessary. X
Examine the spark plug, refer to
To examine the spark plug on page 11
. X
Clean the cooling system. X
Clean the external surface of the carburetor and the area around it. X
Clean or replace the spark arrester mesh. X
Clean the inner surface of the fuel tank. X
Examine the spark plug. X
Make sure that the gear housing is filled with grease. X
To adjust the idle speed
1. Clean the air filter and attach the air filter cover.
2. Start the product, refer to
To start the product with a
cold engine on page 8
.
3. Turn the idle adjustment screw T clockwise until the
cutting attachment starts to move.
10 1075 - 003 - 30.01.2021
4. Turn the idle adjustment screw counterclockwise
until the cutting attachment stops.
WARNING: If the cutting
attachment does not stop when you
adjust the idle speed, speak to your
nearest servicing dealer. Do not use the
product until it is correctly adjusted or
repaired.
Note: The idle speed is correct when the engine
operates smoothly in all positions. Refer to
Technical
data on page 14
for the recommended idle speed.
To clean the cooling system
The cooling system keeps the engine temperature
down. The cooling system includes the cooling fins on
the cylinder, the cylinder cover and the air intake
through the crankcase.
CAUTION: The air intake between the
fuel tank and crankcase, is easily blocked by
leaves. Clean the air intake fully.
1. Clean the cooling system with a brush weekly or
more frequently if it is necessary.
2. Make sure that the cooling system is not dirty or
blocked.
To examine the spark plug
CAUTION: Always use the
recommended spark plug type. Incorrect
spark plug type can cause damage to the
product.
• Examine the spark plug if the engine is low on
power, is not easy to start or does not operate
correctly at idle speed.
• To decrease the risk of unwanted material on the
spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
• If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, refer to
Technical data
on page 14
.
• Replace the spark plug if it is necessary.
To clean the air filter
Clean the air filter regularly from dirt and dust. This
prevents carburetor malfunctions, starting problems,
loss of engine power, wear to engine parts and more
fuel consumption than usual.
1. Remove the air filter cover (A).
2. Remove the foam filter (B) and the felt filter (C) from
the filter frame.
B
C
A
3. Replace the felt filter (C).
4. Clean the foam filter (B) with warm soap water.
Note: An air filter that is used for a long time can
not be fully cleaned. Replace the air filter regularly
and always replace a defective air filter.
5. Make sure that the foam filter (B) is dry.
6. Apply air filter oil to the foam filter (B). Refer to
To
apply oil to the air filter on page 11
7. Clean the inner surface of the air filter cover (A). Use
compressed air or a brush.
To apply oil to the air filter
CAUTION: Always use Redmax special
air-filter oil. Do not use other types of oil.
1075 - 003 - 30.01.2021 11
WARNING: Put on protective gloves.
The air-filter oil can cause skin irritation.
1. Put the air filter in a plastic bag.
2. Put the oil in the plastic bag.
3. Rub the plastic bag to supply the oil equally across
the air filter.
4. Push the unwanted oil out of the air filter while in the
plastic bag.
To lubricate the gear housing
• Use Redmax special grease. Speak to your servicing
dealer for more information about recommended
grease.
• Add the grease through the grease nipple.
CAUTION: Do not fill the gear housing
fully.
To clean and lubricate the blades
1. Clean the blades from unwanted materials before
and after you use the product.
2. Lubricate the blades before long periods of storage.
Note: Speak to your servicing dealer for more
information about recommended cleaning agents and
lubricants.
To examine the blades
1. Remove the cap on the gear housing.
2. Make sure that the blades move freely. Put the
combination wrench in the gear housing and turn
clockwise and counterclockwise.
3. Examine the edges of the blades for damages and
deformation.
4. Use a file to remove burrs on the blades.
Troubleshooting
Troubleshooting
The engine does not start
Problem Possible cause Recommended step
Starter pawls The starter pawls cannot
move freely.
Adjust or replace the starter pawls.
Clean around the starter pawls.
Speak to an approved servicing dealer.
Fuel tank Incorrect fuel type. Drain it and use correct fuel.
Carburetor Incorrect idle speed. Adjust the idle speed.
12 1075 - 003 - 30.01.2021
The engine does not start
Problem Possible cause Recommended step
No spark The spark plug is dirty or
wet.
Make sure that the spark plug is dry and clean.
Incorrect electrode gap.
Clean the spark plug. Make sure that the electrode gap
of the spark plug is correct. Make sure that the spark
plug is installed with a suppressor.
Refer to
Technical data on page 14
for correct elec-
trode gap.
Spark plug The spark plug is loose. Tighten the spark plug.
The engine starts but stops again
Problem Possible cause Recommended step
Fuel tank Incorrect fuel type. Drain it and use correct fuel.
Carburetor Incorrect idle speed. Adjust the idle speed. Refer to
To adjust the idle speed
on page 10
. Speak to your servicing dealer if it is neces-
sary.
Air filter Clogged air filter. Clean the air filter.
Blade
Problem Possible causes Recommended step
The blade moves slowly or
does not move.
The blade is blocked or it is
damaged.
Clean the blades from unwanted materials. Refer to
To
clean and lubricate the blades on page 12
. Remove
burrs from the blade, refer to
To examine the blades on
page 12
. Replace the blade if it is damaged.
The blade does not cut
easily.
The blade is not sharp or it
is damaged.
Sharpen the blade, refer to
To examine the blades on
page 12
. Replace the blade if it is damaged.
The blade becomes hot. There is friction between
the blades.
Remove burrs from the blade and lubricate the blade.
Refer to
To examine the blades on page 12
.
Transportation, storage and disposal
Transportation and storage
• Always allow the product to cool down before
storage.
• For storage and transportation of the product and
fuel, make sure that there are no leaks or fumes.
Sparks or open flames, for example from electrical
devices or boilers, can start a fire.
• Always use approved containers for storage and
transportation of fuel.
• Empty the fuel before transportation or before long-
term storage. Discard the fuel at an applicable
disposal location.
• Attach the transport guard during transportation and
storage.
• Remove the spark plug cap from the spark plug.
• Attach the product during transportation. Make sure
that it cannot move.
1075 - 003 - 30.01.2021 13
• Clean and do servicing on the product before long-
term storage.
Technical data
Technical data
HTZ750
Engine
Cylinder displacement, cu.in/cm31.32/21.7
Idle speed, rpm 3000
Recommended max speed, rpm 9200
Maximum engine power acc. to ISO 8893, kW/hp @ rpm 0.6/0.8 @ 7800
Catalytic converter muffler Yes
Ignition system
Spark plug NGK CMR6A
Electrode gap, inch/mm 0.02/0.5
Fuel
Fuel tank capacity, US Pint/l 0.95/0.45
Weight
Without fuel, lb/kg 11.2/5.1
Blades
Type Single sided
Length, inch/mm 29.5/750
Blade speed, cuts/min 4400
14 1075 - 003 - 30.01.2021
Warranty
CALIFORNIA, U.S FEDERAL, AND
CANADA EXHAUST AND
EVAPORATIVE EMISSIONS
CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board (CARB), U.S.
Environmental Protection Agency (EPA), Environment
and Climate Change Canada and Husqvarna
Professional Products, Inc. are pleased to explain the
exhaust and evaporative emissions ("emissions") control
system warranty on your 2021-2022* small off-road
engine. In California, new equipment that use small off-
road engines must be designed, built, and equipped to
meet State's stringent anti-smog standards. Husqvarna
Professional Products, Inc. must warrant the emissions
control system on your small off-road engine for the
periods of time listed below provided there has been no
abuse, neglect or improper maintenance of your small
off-road engine or equipment leading to the failure of the
emissions control system. Your emissions control
system may include parts such as the carburetor or fuel
injection system, the ignition system, catalytic convertor,
fuel tanks, fuel lines (for liquid fuel and fuel vapors), fuel
caps, valves, canisters, filters, clamps and other
associated components. Also included may be hoses,
belts, connectors, and other emission-related
assemblies. Where a warrantable condition exists,
Husqvarna Professional Products, Inc. will repair your
small off-road engine at no cost to you including
diagnosis, parts and labor.
MANUFACTURER′S WARRANTY COVERAGE
The exhaust and evaporative emissions control system
on your small off-road engine is warranted for two years.
If any emissions-related part on your small off-road
engine is defective, the part will be repaired or replaced
by Husqvarna Professional Products, Inc..
OWNER′S WARRANTY RESPONSIBILITIES
• As the small off-road engine owner, you are
responsible for performance of the required
maintenance listed in your owner’s manual.
Husqvarna Professional Products, Inc. recommends
that you retain all receipts covering maintenance on
your small off-road engine, but Husqvarna
Professional Products, Inc. cannot deny warranty
coverage solely for the lack of receipts or for your
failure to ensure the performance of all scheduled
maintenance.
• As the small off-road engine owner, you should
however be aware that Husqvarna Professional
Products, Inc. may deny you warranty coverage if
your small off-road engine or a part has failed due to
abuse, neglect, or improper maintenance or
unapproved modifications.
• You are responsible for presenting your small off-
road engine to a Husqvarna Professional Products,
Inc. authorized servicing dealer as soon as the
problem exists. The warranty repairs shall be
completed in a reasonable amount of time, not to
exceed 30 days. If you have any questions regarding
your warranty rights and responsibilities, you should
contact Husqvarna Professional Products, Inc. in
USA at 1-800-487-5951, in CANADA at
1-800-805-5523 or send e-mail correspondence to
[email protected] or warranty@hpp-
emissions.com.
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date the engine or
equipment is delivered to an ultimate purchaser.
LENGTH OF COVERAGE
Husqvarna Professional Products, Inc. warrants to the
ultimate purchaser and each subsequent owner that the
engine or equipment is designed, built, and equipped so
as to conform with all applicable regulations adopted by
CARB and EPA, and is free from defects in materials
and workmanship that causes the failure of a warranted
part for a period of two years.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS: Repair or
replacement of any defective warranted part will be
performed at no charge to you at a brand authorized
servicing dealer. Except for repairs and replacement
under this Emission Control Warranty, you may choose
a repair shop or other person to maintain, replace or
repair emission control devices and systems. However,
Husqvarna Professional Products, Inc. recommends that
all maintenance, replacement and repairs of emission
control devices and systems be performed by a brand
authorized servicing dealer.
IMPORTANT:This product is compliant with U.S. EPA
Phase 3 regulations for exhaust and evaporative
emissions. To ensure EPA Phase 3, California Air
Resources Board and Environment and Climate Change
Canada regulation, we recommend using only genuine
product branded replacement parts. Use of non-
compliant replacement parts is a violation of federal and
state laws.
WARRANTY PERIOD: Any warranted part which is not
scheduled for replacement as required maintenance, or
which is scheduled only for regular inspection to the
effect of "repair or replace as necessary" is warranted
for 2 years (or time defined in the product warranty
statement, whichever is longer) from the date of
purchase by the initial consumer purchaser. Any
warranted part which is scheduled for replacement as
required maintenance is warranted for the period of the
time up to the first scheduled replacement for that part.
1075 - 003 - 30.01.2021 15
Any part repaired or replaced under the warranty must
be warranted for the remaining warranty period.
DIAGNOSIS: You will not be charged for diagnostic
labor that leads to the determination that a warranted
part is in fact defective, provided that such diagnostic
work is performed at a brand authorized servicing
dealer.
OTHER DAMAGES: Husqvarna Professional Products,
Inc. will repair other engine components caused by the
failure of a warranted part still under warranty.
EMISSION WARRANTY PARTS LIST
1. Carburetor and intake parts or fuel injection system.
2. Air filter and fuel filter covered up to maintenance
schedule.
3. Spark Plug, covered up to maintenance schedule.
4. Ignition Module.
5. Mufflers with catalyst and exhaust manifolds.
6. Fuel tank, fuel lines (for liquid fuel and fuel vapors),
fuel cap, carbon canister and tip-over/anti-slosh
valves as applicable.**
7. Electronic Controls, Vacuum, temperature, and time
sensitive valves and switches.
8. Hoses, connectors, and assemblies.
9. All other components the failure of which would
increase the engine's exhaust and evaporative
emissions of any regulated pollutant as set forth at
the following:
• For California see California Code of
Regulations, 13 CCR §2405(d) and 2760(d).
• For U.S. and Canada see US Federal Code of
Regulations, 40 C.F.R 1068 Appendix I (iii).
WHAT IS NOT COVERED
All failures caused by abuse, neglect, unapproved
modifications, misuse or improper maintenance are not
covered.
ADD -ON OR MODIFIED PARTS: Add-on or modified
parts that are not exempted by CARB or EPA may not
be used. The use of any non-exempted add-on or
modified parts will be grounds for disallowing a warranty
claim. Husqvarna Professional Products, Inc. will not be
liable to warrant failures of warranted parts caused by
the use of a non-exempted add-on or modified part.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights
and responsibilities, you should contact your nearest
authorized servicing dealer or call Husqvarna
Professional Products, Inc. in USA at 1-800-487-5951,
in CANADA at 1-800-805-5523 or send e-mail
correspondence to [email protected] or
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs are provided through all
Husqvarna Professional Products, Inc. authorized
servicing dealers. If the nearest authorized servicing
dealer is more than 100 miles from your location,
Husqvarna Professional Products, Inc. will arrange and
pay for the shipping costs to and from a brand
authorized servicing dealer or otherwise arrange for
warranty service in accordance with applicable
regulations.
MAINTENANCE, REPLACEMENT AND REPAIR OF
EMISSION-RELATED PARTS
Any replacement part may be used in the performance
of any warranty maintenance or repairs and must be
provided without charge to the owner. Such use will not
reduce the warranty obligations of the manufacturer.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all
required maintenance, as defined in the owner’s
manual.
* Current and following model year will be updated
annually in the warranty statement provided to the
consumer. For example, in 2012 model year, 2012-2013
will be specified.
** Evaporative emission parts.
16 1075 - 003 - 30.01.2021
Contenido
Introducción.................................................................. 17
Seguridad..................................................................... 18
Funcionamiento............................................................ 23
Mantenimiento.............................................................. 26
Solución de problemas................................................. 29
Transporte, almacenamiento y eliminación de
residuos........................................................................ 30
Datos técnicos.............................................................. 30
Garantía........................................................................32
Introducción
Descripción general de la máquina
1
19
10
8
2
313
4
5
21
22
16
14
9
11
15
18
17
7
6
20
12
23
1. Manual del usuario
2. Tapa del depósito de combustible
3. Depósito de combustible
4. Estrangulador
5. Bulbo de la purga de aire
6. Sombrerete de bujía y bujía
7. Mango delantero
8. Interruptor de detención
9. Bloqueo del acelerador
10. Gatillo del acelerador
11. Mango trasero
12. Hoja
13. Cubierta del filtro de aire
14. Caja de engranajes
15. Boquilla de engrase
16. Empuñadura de la cuerda de arranque
17. Cubierta del cilindro
18. Protección para la mano
19. Protección para transporte
20. Recolector de hojas
21. Llave combinada
22. Tubo de grasa
23. Protección de la punta de la hoja
Descripción de la máquina
El producto es un cortasetos con un motor de
combustión.
1075 - 003 - 30.01.2021 17
Uso específico
Utilice el producto para cortar ramas grandes y
pequeñas. No utilice el producto para otras tareas.
Símbolos en la máquina
ADVERTENCIA: Este producto es
peligroso. El operador o las personas que
se encuentran cerca pueden sufrir
lesiones o la muerte si el producto no se
utiliza con cuidado y correctamente. Para
evitar daños graves al operador o a las
personas que se encuentran cerca, lea y
siga todas las instrucciones de seguridad
del manual de usuario.
Lea atentamente el manual de
instrucciones y asegúrese de que
entiende las instrucciones antes de usar
el producto.
Utilice protectores auriculares y oculares
aprobados.
Use guantes protectores homologados.
Use botas antideslizantes de servicio
pesado.
yyyywwxxxx La placa de características muestra
el número de serie. yyyy es el año de
producción y ww es la semana de
producción.
Nota: Otros símbolos o etiquetas en la máquina
hacen referencia a requisitos de certificación para
algunos mercados.
Propuesta 65 de California
WARNING!
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects or other
reproductive harm.
EPA III
El Período de cumplimiento de emisiones al que se
hace referencia en la etiqueta de Cumplimiento de
emisiones indica la cantidad de horas de
funcionamiento en la que se ha demostrado que el
motor cumple los requisitos de emisiones federales y de
California.
Asistencia al cliente
Para comunicarse con asistencia al cliente, llame al:
1-800-291-8251 o visite www.RedMax.com.
Seguridad
Definiciones de seguridad
Las advertencias, precauciones y notas se utilizan para
señalar las piezas particularmente importantes del
manual.
ADVERTENCIA: Se utilizan para
señalar el riesgo de lesiones graves o
mortales para el operador o para aquellos
que se encuentren cerca si no se siguen las
instrucciones del manual.
PRECAUCIÓN: Se utilizan para
señalar el riesgo de dañar la máquina, otros
materiales o el área adyacente si no se
siguen las instrucciones del manual.
Nota: Se utilizan para entregar más información
necesaria en situaciones particulares.
18 1075 - 003 - 30.01.2021
Instrucciones generales de seguridad
ADVERTENCIA: Lea atentamente
las instrucciones de advertencia siguientes
antes de usar el producto.
• El uso incorrecto o descuidado del producto puede
convertirlo en una herramienta peligrosa que puede
causar heridas graves o daños mortales. Es muy
importante que lea y comprenda el contenido de
este manual de usuario.
• En este producto se genera un campo
electromagnético durante su funcionamiento. Este
campo puede, en determinadas circunstancias,
interferir con implantes médicos activos o pasivos.
Para reducir el riesgo de lesiones graves o fatales,
recomendamos a las personas con implantes
médicos consultar a su médico y al fabricante del
implante médico antes de usar esta máquina.
• La sobreexposición a las vibraciones puede producir
trastornos vasculares o nerviosos en personas que
padecen de trastornos circulatorios. Póngase en
contacto con su médico si experimenta síntomas de
la sobreexposición a las vibraciones. Estos síntomas
son entumecimiento, pérdida de sensibilidad,
hormigueo, ardor, dolor, pérdida de fuerza, cambios
en el color o el estado de la piel. Normalmente,
estos síntomas se presentan en los dedos, manos o
muñecas. El riesgo aumenta a bajas temperaturas.
• Si se encuentra en una situación en la que no está
seguro de cómo proceder, debe preguntarle a un
experto. Póngase en contacto con el distribuidor o el
taller de servicio. Evite todos los usos que considere
que están más allá de su capacidad.
• Tenga en cuenta que el operador es responsable de
los accidentes o los peligros que ocurren a otras
personas o sus propiedades.
• Nunca permita que otras personas utilicen el
producto sin asegurarse primero de que hayan
comprendido el contenido del manual del usuario.
• Nunca permita que los niños utilicen el producto o
que estén cerca de este. Debido a que el producto
está equipado con un interruptor de detención que
se acciona por resorte y se puede arrancar con baja
velocidad y fuerza desde la empuñadura de
arranque, incluso niños pequeños pueden, en
determinadas circunstancias, lograr la fuerza
necesaria para arrancar el producto. Esto puede
significar riesgo de daños personales graves. Por
consiguiente, saque el sombrerete de bujía cuando
no se supervise el producto atentamente.
• Almacene el producto fuera del alcance de los niños.
• Nunca utilice el producto si está cansado, si ha
ingerido alcohol o si toma medicamentos que
puedan afectarle la vista, su capacidad de
discernimiento o su coordinación.
• Nunca utilice un producto que esté defectuoso.
Realice las comprobaciones de seguridad, el
mantenimiento y las instrucciones de servicio
descritas en este manual. Especialistas capacitados
y calificados deben llevar acabo algunas medidas de
mantenimiento y servicio. Consulte las instrucciones
en el capítulo Mantenimiento.
• Nunca utilice un producto que se haya modificado
de cualquier modo con respecto a la especificación
original.
Instrucciones de seguridad para el
funcionamiento
ADVERTENCIA: Lea atentamente
las instrucciones de advertencia siguientes
antes de usar el producto.
• No utilice el producto en condiciones climáticas
extremas como frío intenso o climas muy calurosos
o húmedos.
• Las cuchillas defectuosas pueden aumentar el
riesgo de accidentes.
• Asegúrese de que nadie se acerque a menos de
15 m/50 pies mientras trabaja.
• Preste atención a su entorno y asegúrese de que no
haya riesgo de que ninguna persona o animal entre
en contacto con el equipo de corte.
• Inspeccione la zona de trabajo. Retire todos los
objetos que puedan salir eyectados.
• Asegúrese siempre de tener una posición de trabajo
segura y firme.
• Nunca deje el producto sin supervisión con el motor
funcionando.
• Asegúrese de que las manos y los pies no se
acerquen a la unidad de corte cuando el motor esté
funcionando.
• Si algo se atasca en las cuchillas mientras trabaja,
apague el motor y espere hasta que se haya
detenido por completo antes de limpiar las cuchillas.
Desconecte el cable de alta tensión de la bujía.
Consulte
Para examinar las cuchillas en la página
28
.
• Cuando apague el motor, mantenga las manos y los
pies alejados de la unidad de corte hasta que se
haya detenido completamente.
• Tenga cuidado con los trozos de ramas que puedan
salir eyectados durante el corte.
• Preste atención a las señales de advertencia o gritos
cuando utilice protectores auriculares. Siempre retire
sus protectores auriculares apenas se detenga el
motor.
• No trabaje nunca desde una escalera, taburete ni
ninguna otra posición elevada que no cumpla a
cabalidad con las normas de seguridad.
• Utilice siempre las dos manos para sostener el
producto. Mantenga el producto frente a su cuerpo.
• Si se golpea algún objeto extraño o si se producen
vibraciones, detenga la máquina de inmediato.
Desconecte el cable de alta tensión de la bujía.
1075 - 003 - 30.01.2021 19
Compruebe que el producto no esté dañado. Repare
cualquier daño.
• Asegúrese de que el sombrerete de bujía y el cable
de encendido estén en perfecto estado para evitar el
riesgo de descarga eléctrica.
• Verifique que todas las tuercas y tornillos estén
firmes.
• Asegúrese de que la caja de engranajes esté
correctamente lubricada. Consulte
Para lubricar la
caja de engranajes en la página 28
.
• La caja de engranajes se calienta cuando se utiliza
el producto. Para evitar quemaduras, no toque la
caja de engranajes.
• Todas las cubiertas y protecciones se deben montar
antes del uso.
• La protección para transportes siempre debe estar
instalada en la unidad de corte cuando no se esté
utilizando el producto.
Equipo de protección personal
ADVERTENCIA: Lea atentamente
las instrucciones de advertencia siguientes
antes de usar el producto.
• Utilice siempre el equipo de protección personal
adecuado cuando use el producto. El equipo de
protección personal no puede impedir el riesgo de
lesiones, pero disminuirá el grado de lesión si ocurre
un accidente. Permita que su distribuidor le ayude
seleccionar el equipo adecuado.
• Utilice protectores auriculares aprobados que
proporcionen una reducción de ruido adecuada. La
exposición prolongada al ruido puede causar la
pérdida permanente de la audición.
• Use protección ocular homologada. Si utiliza un
visor, también debe usar gafas protectoras
homologadas. Las gafas protectoras homologadas
deben cumplir con la norma ANSI Z87.1 de EE. UU.
o EN 166 para países de la UE.
• Utilice guantes cuando sea necesario, por ejemplo,
cuando conecte, examine o limpie el equipo de
corte.
• Utilice botas o zapatos antideslizantes resistentes.
• Utilice ropa de material resistente. Use siempre
pantalones largos y gruesos, y mangas largas. Evite
usar ropas holgadas que se puedan enganchar con
ramas. No trabaje con joyas, pantalones cortos,
sandalias ni con los pies descalzos. Asegure su
cabello por encima del nivel de los hombros.
• Mantenga un equipo de primeros auxilios a mano.
Dispositivos de seguridad en el producto
ADVERTENCIA: Lea atentamente
las instrucciones de advertencia siguientes
antes de usar el producto.
• No utilice un producto con dispositivos de seguridad
defectuosos.
• Revise los dispositivos de seguridad de forma
regular. Si los dispositivos de seguridad están
defectuosos, comuníquese con su taller de servicio
Redmax.
Comprobación del fiador del acelerador
1. Asegúrese de que el bloqueo del acelerador (A) y el
acelerador (B) se muevan libremente y que el muelle
de retorno funcione de manera correcta.
A
B
20 1075 - 003 - 30.01.2021
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
dans d''autres langues
- English: RedMax HTZ750 User manual
- español: RedMax HTZ750 Manual de usuario