DeWalt DCCS623 20V Max* Pruner Manuel utilisateur

Marque: DeWalt

Modèle: DCCS623 20V Max* Pruner

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

DCCS623

20V Max* Pruner

Tronçonneuse 20 V Max*

Podadora 20V MAX*

Instruction Manual

Guide D’utilisation

Manual de instrucciones

English (original instructions) 3

Français (traduction de la notice d’instructions originale) 17

Español (traducido de las instrucciones originales) 31

Fig. A DCCS623

Components

1 Trigger switch

2 Lock‑off lever

3 Front hand guard

4 Guide bar

5 Saw chain

6 Bar tip guard

7 Sprocket cover

8 Bar lock nut

9 Chain tensioning screw

10 Oil level indicator

11 Oil cap

12 Scabbard

13 Wrench

14 Rear handle

15 Front handle

16 Battery Pack

17 Battery release button

Composants

1 Gâchette

2 Levier de verrouillage

3 Protecteur de la poignée avant

4 Guide‑chaîne

5 Tronçonneuse

6 Protecteur d’embout de barre

7 Capot du pignon

8 Écrou de blocage du guide‑chaîne

9 Vis de tension de la chaîne

10 Indicateur du niveau d’huile

11 Capuchon de l’huile

12 Étui

13 Clé

14 Poignée arrière

15 Poignée avant

16 Bloc de batterie

17 Bouton de libération de la pile

Componentes

1 Interruptor de gatillo

2 Palanca de bloqueo de apagado

3 Protección de mano delantera

4 Barra guía

5 Cadena de sierra

6 Protección de punta de barra

7 Cubierta de rueda dentada

8 Tuerca de bloqueo de barra

9 Tornillo de tensión de cadena

10 Indicador de nivel de aceite

11 Tapa de aceite

12 Vaina

13 Llave

14 Manija trasera

15 Manija delantera

16 Paquete de batería

17 Botón de liberación de batería

Fig.B Fig.C

Fig.D Fig.E

Fig.F Fig.G

1/8" (3 mm)

75–100% charged

Chargé de 75 à 100 %

75–100% cargada

51–74% charged

Chargé de 51 à 74 %

51–74% cargada

< 50% charged

Chargé de < 50 %

< 50% cargada

Pack needs to be charged

Le bloc-piles doit être rechargé

La batería tiene que cargarse

Indicators/Témoin/Indicador

Charging

Bloc-piles en Cours

de Chargement

Unidad en Proceso de Carga

Fully Charged

Bloc-piles Chargé

Unidad Cargada

Hot/Cold Pack Delay

Suspension de Charge Contre

le Chaud/Froid

Restraso por Unidad Caliente/

Fría

Fig.H Fig.I

Fig.L Fig.M

Fig.N Fig.O

14 17 16

60°

.025"

(0.635mm)

Fig.P

Fig.K

Fig.J

ENGLISH

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non‑skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off‑position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energizing power tools that have the switch

on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of the

power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewelry or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust‑relatedhazards.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS

AND INSTRUCTIONS FOR

FUTUREREFERENCE.

The term “power tool” in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated

(cordless) powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert

symbols and words to alert you to hazardous situations and

your risk of personal injury or propertydamage.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

(Used without word) Indicates a safety relatedmessage.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Intended Use

The DCCS623 pruner is designed for pruning applications up

to 6" (152 mm) indiameter.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

This pruner is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

English (original instructions)

WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

ENGLISH

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

e ) Do not use a battery pack or tool that is damaged

or modified. Damaged or modified batteries may

exhibit unpredictable behavior resulting in fire,

explosion or risk ofinjury.

f ) Do not expose a battery pack or tool to

fire or excessive temperature. Exposure to

fire or temperature above 265°F (130°C) may

causeexplosion.

g ) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and increase

the risk offire.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of

untrainedusers.

e ) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation. If

damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result in

a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

Pruner Safety Warnings

a ) Keep all parts of the body away from the saw

chain when the pruner is operating. Before you

start the pruner, make sure the saw chain is not

contacting anything. A moment of inattention while

operating pruners may cause entanglement of your

clothing or body with the sawchain.

b ) Always hold the pruner with your right hand on

the rear handle and your left hand on the front

handle. Holding the pruner with a reversed hand

configuration increases the risk of personal injury and

should never bedone.

c ) Hold the power tool by insulated gripping

surfaces only, because the saw chain may contact

hidden wiring. Saw chains contacting a "live" wire

may make exposed metal parts of the pruner "live" and

could give the operator an electricshock.

d ) Wear safety glasses and hearing protection.

Further protective equipment for, head, hands,

legs and feet is recommended. Adequate protective

clothing will reduce personal injury from flying debris or

accidental contact with the sawchain.

e ) Do not operate a pruner in a tree. Operation of a

pruner while up in a tree can result in personalinjury.

f ) Always keep proper footing and operate the

pruner only when standing on ﬁxed, secure and

level surface. Slippery or unstable surfaces may cause

a loss of balance or control of the pruner.

ENGLISH

g ) When cutting a limb that is under tension, be

alert for spring back. When the tension in the wood

ﬁbers is released, the spring loaded limb may strike the

operator and/or throw the pruner out ofcontrol.

h ) Use extreme caution when cutting brush and

saplings. The slender material could catch the

saw chain and be whipped toward you or pull you

offbalance.

i ) Carry the pruner by the front handle with the

pruner switched off and away from your body.

When transporting or storing the pruner always

ﬁt the guide bar scabbard. Proper handling of the

pruner will reduce the likelihood of accidental contact

with the moving sawchain.

j ) Follow instructions for lubricating, chain

tensioning and changing accessories. Improperly

tensioned or lubricated chain could break the

prunerchain.

k ) Keep handles dry, clean, and free from oil

andgrease. Greasy, oily handles are slippery,

causing loss ofcontrol.

l ) Cut wood only. Do not use pruner for purposes

not intended. For example: do not use pruner for

cutting plastic, masonry or non‑wood building

materials. Use of the pruner for operations different

than intended could result in a hazardoussituation.

m ) Maintain a firm grip, with thumbs and fingers

encircling the pruner handles, with both hands

on the pruner. Maintaining control of the pruner

will reduce the risk of losing control. Do not let go

of the pruner.

n ) Do not overreach and do not cut above shoulder

height. This enables better control of the pruner in

unexpected situations.

o ) Only use replacement bars and chains specified

by the manufacturer. Incorrect replacement bars

and chains can cause chain breakage and increase the

risk of injury.

p ) Follow the manufacturer's sharpening and

maintenance instructions for the pruner chain.

Decreasing the depth gauge height can lead to

increased risk of injury.

Causes and Operator Prevention

ofKickback:

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches

the saw chain in thecut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards

theoperator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards theoperator.

Either of these reactions may cause you to lose control of

the saw which could result in serious personal injury. Do not

rely exclusively upon the safety devices built into your saw.

As a pruner user, you should take several steps to keep your

cutting jobs free from accident orinjury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

a ) Maintain a firm grip, with thumbs and ﬁngers

encircling the pruner handles, with both hands

on the saw and position your body and arm to

allow you to resist kickback forces. Kickback

forces can be controlled by the operator, if proper

precautions are taken. Do not let go of the pruner.

b ) Do not overreach and do not cut above

shoulder height. This helps prevent unintended tip

contact and enables better control of the pruner in

unexpectedsituations.

c ) Only use replacement bars and chains speciﬁed

by the manufacturer. Incorrect replacement bars and

chains may cause chain breakage and/orkickback.

d ) Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increasedkickback.

The Following Precautions Should Be

Followed to Minimize Kickback:

1 . Grip saw firmly. Hold the pruner firmly with both

hands when the motor is running. Use a firm grip

with thumbs and fingers encircling the pruner

handles. Pruner will pull forward when cutting on the

bottom edge of the bar, and push backward when cutting

along the top edge of thebar.

2 . Do not overreach.

3 . Keep proper footing and balance at alltimes.

4 . Don’t let the nose of the guide bar contact a log,

branch, ground or otherobstruction.

5 . Don’t cut above shoulderheight.

6 . Use devices such as low kickback chain and reduced

kickback guide bars that reduce the risks associated

withkickback.

7 . Only use replacement bars and chains specified by

the manufacturer or theequivalent.

8 . Never let the moving chain contact any object at the

tip of the guidebar.

9 . Keep the working area free from obstructions such

as other trees, branches, rocks, fences, stumps, etc.

Eliminate or avoid any obstruction that your saw chain

could hit while you are cutting through a particular log

orbranch.

10 . Keep your saw chain sharp and properly tensioned.

A loose or dull chain can increase the chance of

kickback. Check tension at regular intervals with the

motor stopped and tool unplugged, never with the

motorrunning.

11 . Begin and continue cutting only with the chain

moving at full speed. If the chain is moving at a slower

speed, there is a greater chance for kickback tooccur.

12 . Cut one log at atime.

ENGLISH

13 . Use extreme caution when re‑entering a previous cut.

Engage the ribbed bumpers 21 onto the wood and allow

the chain to reach full speed before proceeding witha cut.

14 . Do not attempt plunge cuts or borecuts.

15 . Watch for shifting logs or other forces that could

close a cut and pinch or fall intochain.

Kickback Safety Features

WARNING: The following features are included

on your saw to help reduce the hazard of kickback;

however such features will not totally eliminate this

dangerous reaction. As a pruner user do not rely

only on safety devices. You must follow all safety

precautions, instructions, and maintenance in this

manual to help avoid kickback and other forces which

can result in seriousinjury.

• Reduced‑Kickback Guide Bar, designed with a small radius

tip which reduces the size of the kickback danger zone on

bar tip. A reduced ‑ kickback guide bar is one which has

been demonstrated to significantly reduce the number and

seriousness of kickbacks when tested in accordance with

safety requirements for electric pruners.

• Low‑Kickback Chain, designed with a contoured depth

gauge and guard link which deflect kickback force and

allow wood to gradually ride into the cutter. A low‑kickback

chain is a chain which has met kickback performance

requirements of ANSI B175.1–2012.

• Do not operate pruner while in a tree, on a ladder, on a

scaffold, or from any unstablesurface.

• Hold tool by insulated gripping surfaces when performing

an operation where the cutting tool may contact hidden

wiring. Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock theoperator.

• Do not attempt operations beyond your capacity or

experience. Read thoroughly and understand completely all

instructions in thismanual.

• Before you start pruner, make sure saw chain is not

contacting anyobject.

• Do not operate a pruner with one hand! Serious injury to the

operator, helpers, or bystanders may result from one handed

operation. A pruner is intended for two‑handed useonly.

• Keep the handles dry, clean, and free of oil orgrease.

• Do not allow dirt, debris, or sawdust to build up on the

motor or outside airvents.

• Stop the pruner before setting itdown.

• Do not cut vines and/or small underbrush.

• Use extreme caution when cutting small size brush and

saplings because slender material may catch the saw chain

and be whipped toward you or pull you offbalance.

• Drive Sprocket or Sprocket ‑ The toothed part that drives

the sawchain.

• Felling ‑

The process of cutting down atree.

• Felling Back Cut ‑

The final cut in a tree felling operation

made on the opposite side of the tree from the notchingcut.

• Front Handle ‑ The support handle located at or toward

the front of the pruner.

• Front Hand Guard ‑ A structural barrier between the front

handle of a pruner and the guide bar, typically located

close to the hand position on the fronthandle.

• Guide Bar ‑ A solid railed structure that supports and

guides the sawchain.

• Scabbard/Guide Bar Cover ‑ Enclosure fitted over guide

bar to help prevent tooth contact when saw is not inuse.

• Kickback ‑ The backward or upward motion, or both of the

guide bar occurring when the saw chain near the nose of

the top area of the guide bar contacts any object such as a

log or branch, or when the wood closes in and pinches the

saw chain in thecut.

• Kickback, Pinch ‑

The rapid pushback of the saw which

can occur when the wood closes in and pinches the moving

saw chain in the cut along the top of the guidebar.

• Kickback, Rotational ‑ The rapid upward and backward

motion of the saw which can occur when the moving saw

chain near the upper portion of the tip of the guide bar

contacts an object, such as a log orbranch.

• Limbing ‑ Removing the branches from a fallentree.

• Low‑Kickback Chain ‑ A chain that complies with the

kickback performance requirements of ANSI B175.1–2012

(when tested on a representative sample of pruners.)

• Normal Cutting Position ‑ Those positions assumed in

performing the bucking and fellingcuts.

• Notching Undercut ‑ A notch cut in a tree that directs the

tree’sfall.

• Rear Handle ‑ The support handle located at or toward

the rear of thesaw.

• Reduced Kickback Guide Bar ‑ A guide bar which has

been demonstrated to reduce kickbacksignificantly.

• Replacement Saw Chain ‑ A chain that complies with

kickback performance requirements of ANSI B175.1–2012

when tested with specific pruners. It may not meet the ANSI

performance requirements when used with othersaws.

• Saw Chain ‑ A loop of chain having cutting teeth, that cut

the wood,and that is driven by the motor and is supported

by the guidebar.

• Ribbed Bumper ‑ The ribs used when felling or bucking to

pivot the saw and maintain position whilesawing.

• Switch ‑ A device that when operated will complete

or interrupt an electrical power circuit to the motor of

thepruner.

• Switch Linkage ‑ The mechanism that transmits motion

from a trigger to theswitch.

• Switch Lockout ‑ A movable stop that prevents

the unintentional operation of the switch until

manuallyactuated.

Pruner Names and Terms

• Bucking ‑ The process of cross cutting a felled tree or log

intolengths.

• Motor Brake (if equipped) ‑ A device used to stop the saw

chain when the trigger isreleased.

• Pruner Powerhead ‑ A pruner without the saw chain and

guidebar.

ENGLISH

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs

WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into a

non‑compatible charger as battery pack may rupture

causing serious personal injury. Consult the chart at the

end of this manual for compatibility of batteries andchargers.

• Charge the battery packs only in DeWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• DO NOT allow water or any liquid to enter batterypack.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

...................... Class II

Construction

(double insulated)

no .......................no load speed

n .........................rated speed

m/s ..................... meters per second

......................earthing terminal

.............safety alert symbol

.............Visible radiation

............. Wear respiratory

protection

............. Wear eye protection

............. Wear hearing protection

............. Read all documentation

CSPM .......... Cut strokes per minute

............. Do not leave in rain

............. Do not use front hand

guard as a handle

............ Tip contact can cause

the guide bar to move

suddenly upward and

backward, which can

cause serious injury

............ Contact of the guide

bar tip with any object

should be avoided

........... Rotational direction of

the saw chain

...... Always use two hands

when operating the pruner

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or direct

current

Additional Safety Information

WARNING: Never modify the power tool or any part of

it. Damage or personal injury couldresult.

WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or dust

mask if operation is dusty. ALWAYS WEAR CERTIFIED

SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.

WARNING: Some dust contains chemicals known

to State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these

chemicals are:

• compounds in fertilizers,

• compounds in insecticides, herbicides

andpesticides,

• arsenic and chromium from chemically treatedlumber.

To reduce your exposure to these chemicals, wear

approved safety equipment such as dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.

WARNING: Use of this tool can generate and/or

disperse dust, which may cause serious and permanent

respiratory or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate for

the dust exposure. Direct particles away from face

andbody.

WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.

CAUTION:

When not in use, place tool on its side on

a stable surface where it will not cause a tripping or

falling hazard. Some tools with a large battery pack will

stand upright but may be easily knockedover.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in movingparts.

ENGLISH

Important Safety Instructions for All

Battery Chargers

WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than a DeWALT charger. DeWALT

chargers and battery packs are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging DeWALT rechargeable battery packs.

Charging other types of battery packs may cause them to

overheat and burst, resulting in personal injury, property

damage, fire, electric shock orelectrocution.

• Do not expose the charger to rain orsnow.

• Do not allow water or any liquid to entercharger.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

The RBRC® Seal

Please take your spent battery packs to

an authorized DeWALT service center or

to your local retailer for recycling. In some

areas, it is illegal to place spent battery

packs in the trash. You may also contact your local recycling

center for information on where to drop off the spent

battery pack. Do not place in curbside recycling. For more

information visit www.call2recycle.org. or call the toll free

number in the RBRC®Seal.

RBRC® is a registered trademark of Call 2Recycle,Inc.

Shipping the DeWALT FLEXVOLT® Battery Pack

The DeWALT FLEXVOLT® battery pack has a battery cap that

should be used when shipping the batterypack.

Attach the cap to the battery pack to ready it for shipping.

This converts the battery pack to three separate 20V

batteries. The three batteries have the Watt hour rating

labeled “Shipping” on the battery pack. If shipping without

the cap or in a tool, the pack is one battery at the Watt hour

rating labeled“Use”.

Example battery pack label:

USE: 120Wh SHIPPING: 3x 40Wh

In this example, the battery pack is three batteries with

40Watt hours each when using the cap. Otherwise, the

battery pack is one battery with 120Watthours.

not be put in checked baggage on airplanes and must

be properly protected from short circuits if they are in

carry‑onbaggage.

can explode in a fire. Toxic fumes and materials are created

when lithium‑ion battery packs areburned.

• Do not expose a battery pack or appliance to ﬁre or

excessive temperature. Exposure to ﬁre or temperature

above 265°F (130°C) may causeexplosion.

• Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature

range specified in the instructions. Charging improperly or

at temperatures outside of the specified range may damage

the battery and increase the risk offire.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of a

mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.

• Battery liquid may be flammable if exposed to spark

orflame.

• Never attempt to open the battery pack for any

reason. If the battery pack case is cracked or

damaged, do not insert into the charger. Do not crush,

drop or damage the battery pack. Do not use a battery pack

or charger that has received a sharp blow, been dropped,

run over or damaged in any way (e.g., pierced with a nail,

hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center forrecycling.

Storage Recommendations

The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold. Store the fully

charged battery pack out of thecharger.

Battery Pack Cleaning Instructions

Dirt and grease may be removed from the exterior of the

battery pack using a cloth or soft non‑metallic brush. Do not

use water or any cleaningsolutions.

Fuel Gauge Battery Packs (Fig.B)

Some battery packs include a fuel gauge. When the fuel

gauge button is pressed and held, the LED lights will

indicate the approximate level of charge remaining. This

does not indicate tool functionality and is subject to

variation based on product components, temperature, and

end‑userapplication.

Transportation

WARNING: Fire hazard. Do not store, carry, or

transport the battery pack so that metal objects

can contact exposed battery terminals. For

example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc.,

with loose nails, screws, keys, coins, hand tools, etc.

When transporting individual battery packs, make

sure that the battery terminals are protected and well

insulated from materials that could contact them and

cause a short circuit. NOTE: Li‑ion battery packs should

ENGLISH

Charging a Battery (Fig.C)

1. Plug the charger into an appropriate outlet.

2. Insert and fully seat battery pack16. The red charging

light(s) will continuously blink whilecharging.

3. Charging is complete when the red charging light(s)

remain(s) continuously ON. Battery pack can be left in

charger or removed. Some chargers require the battery

pack release button to be pressed forremoval.

WARNING:

Only charge batteries in air temperature over

40° F (4.5° C) and below 104° F (+40°C).

4. Charger will not charge a faulty battery pack, which may

be indicated by the charging light(s) staying OFF. Take

charger and battery pack to an authorized service center

if light(s) stay(s)OFF.

NOTE: Refer to label near charging light(s) on charger

for blinkpatterns. Older chargers may have additional

information and/or may not have a yellow indicatorlight.

NOTE: To remove the battery pack, some chargers

require the battery pack release button to bepressed.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack may charge at a slower rate than a warm

batterypack.

The hot/cold pack delay will be indicated by the red light(s)

continuing to blink but with the yellow light continuously

ON. Once the battery pack has reached an appropriate

temperature, the yellow light will turn OFF and the charger

will resume the chargingprocedure.

DCB118 and DCB1112 Chargers

The DCB118 and DCB1112 chargers are equipped with

an internal fan designed to cool the battery pack. The fan

will turn on automatically when the battery pack needs to

becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

Electronic Protection System

Li‑Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deep discharge. The tool will automatically

turn off and the battery pack will need to berecharged.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature

is between 65°F – 75°F (18° C– 24°C). DO NOT charge

when the battery pack is below +40°F (+4.5°C), or

above +104°F (+40°C). This is important and will

prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the heavier the cord and

thus the greater its capacity. An undersized cord will

cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size

to use depending on total length of all extension cords

plugged together, and nameplate ampere rating. If in

doubt, use the next heaviergauge.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

(meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

Ampere Rating

American Wire Gauge

More Than Not More

Than

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source.

The charger is ventilated through slots in the top and the

bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug. Have them replacedimmediately.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

• Foreign materials of a conductive nature, such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil or any buildup of metallic particles

should be kept away from the charger cavities and

ventilation slots.

• Always unplug the charger from the power supply

when there is no battery pack in thecavity.

ENGLISH

Adjusting Chain Tension (Fig. A, D–G)

NOTE: Saw chain tension should be adjusted regularly before

eachuse.

1. With the saw still on a firm surface check the saw

chain5 tension. The tension is correct when the saw

chain snaps back after being pulled 1/8" (3 mm) away

from the guide bar4 with light force from the middle

finger and thumb as shown in Fig.F. There should be no

“sag” between the guide bar and the saw chain on the

underside as shown in Fig.G.

2. To adjust saw chain tension, loosen bar lock nut8.

3. Rotate the chain tension screw9 in the front of the

housing using the flat screwdriver end of thewrench 13 .

4. Check saw chain tension, adjust ifneeded.

5. Do not over‑tension the saw chain as this will lead to

excessive wear and will reduce the life of the guide bar

and saw chain.

6. Once saw chain tension is correct, tighten bar lock nut8

untilsnug

7. A new chain stretches slightly during the first few hours

of use. It is important to check the tension frequently

(after disconnecting battery remove the battery pack)

during the first twohours ofuse.

1. Place the saw on a flat, firmsurface.

2. Rotate the bar lock nut8 counterclockwise with the

wrench 13 provided.

3. Remove sprocket cover7, and bar lock nut8.

4. Wearing protective gloves, grasp the saw chain5 and

wrap it around the guide bar4, ensuring the teeth are

facing the correct direction (Fig.H).

5. Ensure the chain is properly set in the slot around the

entire guidebar.

6. Place the saw chain around the sprocket22. While

lining up the slot on the guide bar with chain tensioning

pin19, and the bolt18, on the base of the tool as

shown in Fig.E.

7. Once in place, hold the bar still, replace sprocket cover7.

Install the rear of the sprocket cover first, rotate it down

and make sure the bolt hole on the cover lines up with

the bolt18, on the mainhousing.

8. Install the bar lock nut8 and rotate clockwise with the

wrench 13 provided

until snug

, then loosen nut one full

turn, so that the saw chain can be properlytensioned.

9. Rotate the chain tensioning screw9 clockwise to

increase tension as shown in Fig.E. Make sure the saw

chain5 is snug around the guide bar4. Tighten the bar

lock nut8

untilsnug

10. Follow the instructions in the section Adjusting

ChainTension.

Installing the Guide Bar and Saw Chain

(Fig. A, D–H)

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can

cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to

do this could result in serious personalinjury.

If the saw chain5 and guide bar4 are packed separately in

the carton, the chain has to be attached to the bar, and both

must be attached to the body of thetool.

ASSEMBLY AND ADJUSTMENTS

WARNING:

To reduce the risk of serious personal

injury, turn unit off and

remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

Wall Mounting

Some DeWALT chargers are designed to be wall mountable

or to sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet, and

away from a corner or other obstructions which may impede

air flow. Use the back of the charger as a template for the

location of the mounting screws on the wall. Mount the

charger securely using drywall screws (purchased separately)

at least 1” (25.4mm) long, with a screw head diameter of

0.28–0.35” (7–9mm), screwed into wood to an optimal

depth leaving approximately 7/32” (5.5 mm) of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out

thelights;

c. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. You may charge a partially used pack whenever you

desire with no adverse effect on the batterypack.

Charger Cleaning Instructions

WARNING:Shock hazard. Disconnectthe charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non‑metallic brush. Do not use water or

any cleaningsolutions.

ENGLISH

Proper hand position requires the left hand on the front

handle15, under the front hand guard 3 , with the right

hand on the rear handle14.

Proper Hand Position (Fig.A, L)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

OPERATION

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Bar Tip Guard (Fig.A, K)

WARNING: Never operate the pruner without the

bar tip guard properly mounted on the guide bar

to prevent rotational kickback.

The bar tip guard 6 reduces the chance of the chain 5 at

the end of the guide bar 4 from coming into contact with

objects which may cause the bar and chain to kickback

towards the operator. In addition to reducing the chance of

kickback, the bar tip guard 6 will reduce the chance of the

chain from touching the ground.

Scabbard and Wrench Storage (Fig.A, I–K)

The scabbard12 has two functions, to cover the guide bar4

when the tool is not in use and to store the wrench13 .

Scabbard

1. To open the scabbard12 , lift up on the latch 25 and

pull the two halves apart.

2. Fit the scabbard 12 onto the guide bar4 as shown

in Fig. A, I–K. Ensure that the retaining pin 29 on the

scabbard 12 aligns with the retaining hole 30 on the

guide bar4.

3. To close the scabbard 12 , close the two halves and

ensure the latch 25 is secured to the notch 26 .

Wrench

1. Open the scabbard 12 to gain access to the wrench13 .

2. Remove the wrench13 by lifting the wrench end up

and away from the scabbard.

3. Store the wrench in the scabbard when finished. First

install flat screwdriver end of the wrench into the retaining

slot 27 and then press the wrench end down until the

retaining clips 28 firmly secure the wrench13 in place.

2. Refit the oil cap and tightenclockwise.

3. Periodically switch the pruner off and check the oil

level indicator to ensure the bar and chain are being

properlyoiled.

Saw Chain and Guide Bar Oiling (Fig.A)

Auto Oiling System

This pruner is equipped with an auto oiling system that keeps

the saw chain and guide bar constantly lubricated.

1. The oil level indicator10 shows the level of the oil in the

pruner. If the oil level is less than a quarter full, remove

the battery from the pruner and refill the oil tank with the

correct type of oil.

2. Always empty oil tank when finishedcutting.

NOTE: Do not to operate this pruner without oil.

NOTE: Always use a high‑quality, biodegradable bar

and chain oil for proper saw chain and bar lubrication.

When pruning trees, vegetable‑based bar and chain oil is

recommended, as mineral‑based oils may harm living trees.

Never use dirty, used, or contaminated oil. Doing so may

damage the tool.

Filling the Oil Reservoir

1. Unscrew counterclockwise and then remove the oil

cap11. Fill the reservoir with the recommended bar and

chain oil until the oil level has reached the top of the oil

level indicator10.

Replacement chain and bar are available from your

nearest authorized servicecenter.

The DCCS623 requires replacement 8"(203mm) chain

DWO1DT608

. Replacement 8" (203mm) barDWZCSB8P.

NOTE: Do not use replacement 8" (203mm) bar DWZCSB8.

Replacing the Saw Chain (Fig.A, F, H)

WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to

do this could result in serious personalinjury.

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can

cut you when it is notrunning.

CAUTION: The chain speed of this product is 8.6 m/s.

Only use chains that are rated at greater than 8.6 m/s.

1. Place the saw on a flat, firmsurface.

2. Remove sprocket cover7 as described in Installing the

Guide Bar and Saw Chainsection.

3. To remove the saw chain5, rotate the chain tension

screw9 in the front of the housing using the flat

screwdriver end of the wrench. Turning the screw

counterclockwise allows the guide bar4 to recede

and reduces the tension on the chain so that it may

beremoved.

4. Wearing protective gloves, grasp the saw chain and lift

the worn saw chain out of the groove in the guidebar.

5. Ensure guide bar is installed with the bar tip guard 6

positioned as shown in Fig.F.

6. Place the new chain in the slot of the guide bar, making

sure the saw teeth are facing the correct direction by

matching the arrow and graphic of the saw chain on the

sprocket cover7 shown in Fig.H.

7. Follow instructions for Installing the Guide Bar and

SawChain.

NOTE: DO NOT hold the saw by the front hand guard 3 .

Transporting Pruner (Fig.A, K)

• Always turn unit off, remove the battery and cover the

guide bar4 with the scabbard12 when transporting

thepruner.

ENGLISH

Always be sure of your footing and grip the pruner firmly

with both hands with the thumb and fingers encircling

bothhandles.

1. To turn the unit on, push down on the the lock off lever2,

shown in Fig.A, and squeeze the trigger switch1. Once

the unit is running, you may release the lock offlever.

2. To keep the unit running you must continue to squeeze

the trigger switch1.

3. To turn the unit off, release thetrigger switch1.

NOTE: If too much force is applied while making a cut the

pruner will turn off. To restart pruner, you must release the

lock off lever2 and the trigger switch1 before the pruner

will restart. Begin your cut again this time with less force.

Allow the pruner to cut at its ownpace.

Operating the Pruner (Fig.A)

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below may result

in electric shock, fire and/or serious personalinjury.

• Guard Against Kickback which can result in severe

injury or death. See Important Safety Instructions

Guard Against Kickback, to avoid the risk

ofkickback.

• Do not overreach. Do not cut above chest height.

Make sure your footing is firm. Keep feet apart.

Divide your weight evenly on bothfeet.

• Use a firm grip with your left hand on the front

handle15 and your right hand on the rear

handle14 so that your body is to the left of the

guidebar.

WARNING: Do not hold pruner by front hand guard.

Keep elbow of left arm locked so that left arm is straight

to withstand akickback.

WARNING: Never use a cross‑handed grip (left hand

on the rear handle and right hand on the fronthandle).

WARNING: Never allow any part of your body to

be in line with the guide bar when operating the

chainpruner.

• Never operate pruner while in a tree, in any

awkward position or on a ladder or other unstable

surface. You may lose control of pruner causing

severeinjury.

• Keep the pruner running at full speed the entire

time you arecutting.

• Allow the chain to cut for you. Exert only light pressure.

Do not put pressure on pruner at end ofcut.

WARNING: When not in use always have the chain

brake (if equipped) engaged, unit turned off and

remove the battery pack.

WARNING: Never operate the pruner without the

bar tip guard properly mounted on the guide bar

to prevent rotational kickback.

ON/OFF Switch (Fig.A)

WARNING: Never attempt to lock a switch in the

ONposition.

Installing and Removing the Battery Pack

(Fig.M)

WARNING: Ensure the tool/appliance is in the off

position before inserting the batterypack.

NOTE: For best results, make sure your battery pack is

fullycharged.

1. To install the battery pack16 into the tool handle, align

the battery pack with the rails inside the tool’s handle

and slide it into the handle until the battery pack is firmly

seated in the tool and ensure that it does notdisengage.

2. To remove the battery pack from the tool, press the

release button17 and firmly pull the battery pack out of

the tool handle. Insert it into the charger as described in

the charger section of thismanual. Common Cutting Techniques

Limbing

Removing the branches from a fallen tree. When limbing,

leave larger lower limbs to support the log off the ground.

Remove the small limbs in one cut. Branches under tension

should be cut from the bottom of the branch towards the

top to avoid binding the pruner as shown below. Trim limbs

from opposite side keeping tree stem between you and

pruner. Never make cuts with pruner between your legs or

straddle the limb to becut.

Bucking

WARNING: Recommend that first time users should

practice cutting on a prunerhorse.

Cutting a felled tree or log into lengths. How you should cut

depends on how the log is supported. Use a pruner horse

wheneverpossible as shownbelow.

1. Always start a cut with the pruner chain running at

fullspeed.

2. Place the ribbed bumper 21 of the pruner behind the

area of the initial cut as shownbelow.

ENGLISH

Sprocket and Sprocket Cover (Fig.A, F, H)

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can

cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent accidental

operation, ensure the battery is removed from the

tool is unplugged before performing the following

operations. Failure to do this could result in serious

personalinjury.

1. Place the saw on a flat, firmsurface.

2. Remove sprocket cover7 as described in Installing the

Guide Bar and Saw Chainsection.

3. Wearing protective gloves, use a clean, soft bristle brush

to wipe away any saw dust, sticks, vines or other debris

that may have collected inside the sprocket cover7 and

around the chain5 or sprocket22.

4. Rotate the chain tension screw9 using the flat

screwdriver end of thewrench13. Turning the screw

counterclockwise allows the guide bar4 to recede

and reduces the tension on the chain so that it may

beremoved.

5. Wearing protective gloves, grasp the saw chain and

guidebar and lift them away from the tool.

6. Wearing protective gloves, use a clean, soft bristle brush

to wipe away any saw dust or other debris that may have

collected on the guide bar4 and around the chain5.

7. Install the chain, guide bar and sprocket cover7

as described in Installing the Guide Bar and Saw

Chain, Replacing the Saw Chainsections and adjust

Saw Chain and Guide Bar

After every few hours of use, remove the sprocket cover,

guide bar and chain and clean thoroughly using a soft bristle

brush. Ensure oiling hole on bar is clear of debris.

Cleaning

WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performing thisprocedure.

WARNING: Never use solvents or other harsh

chemicals for cleaning the non‑metallic parts of the

tool. These chemicals may weaken the plastic materials

used in these parts. Use a cloth dampened only with

water and mild soap. Never let any liquid get inside the

tool; never immerse any part of the tool into aliquid.

MAINTENANCE

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Your DeWALT power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.

3. Turn the pruner on then rotate the pruner chain and bar

down into the tree, using the ribbed bumper as ahinge.

4. Once the pruner gets to a 45° angle, level the pruner

again and repeat steps until you cut fullythrough.

5. When the tree is supported along its entire length, make

a cut from the top (overbuck), but avoid cutting the earth

as this will dull your prunerquickly.

CUT FROM TOP (OVERBUCK)

AVOID CUTTING EARTH

• When supported at one end first, cut 1/3 the diameter

from the underside (underbuck). Then make the finishing

cut by overbucking to meet the firstcut as shownbelow.

2nd CUT OVERBUCK

(2/3 DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT UNDERBUCK

(1/3 DIAMETER)

AVOID SPLINTERING

• When supported at bothends. First, cut 1/3 down from the

top overbuck. Then make the finished cut by underbucking

the lower 2/3 to meet the firstcut as shownbelow.

2nd CUT UNDERBUCK

(2/3 DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT OVERBUCK

(1/3 DIAMETER)

TO AVOID SPLINTERING

• When on a slope always stand on the uphill side of

the log. When “cutting through”, to maintain complete

control reduce the cutting pressure near the end of the

cut without relaxing your grip on the pruner handles.

Don’t let the chain contact the ground. After completing

the cut, wait for the pruner chain to stop before you

move the pruner. Always stop the motor before moving

from cut tocut.

ENGLISH

Accessories

WARNING:

Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this product could be hazardous.

To reduce the risk of injury, only DeWALT recommended

accessories should be used with thisproduct.

Recommended accessories for use with your product are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact DeWALT call 1-800-4-DeWALT

(1-800-433-9258) or visit our website: www.dewalt.com

chain tension properly before use as described in

theAdjustingChain Tensionsection.

Saw Chain Sharpening (Fig.N–P)

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can

cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to

do this could result in serious personalinjury.

WARNING: Do not over file chain rakers, this will

increase the risk of kickback. If the chain has been

sharpened more than four times, replaceit.

Each time the chain is sharpened, it loses some of the low

kickback qualities and extra caution should beused.

It is recommended that a saw chain be sharpened no more

than fourtimes.

NOTE: The cutters will dull immediately if they touch the

ground/dirt or a nail whilecutting.

To get the best possible performance from your pruner it is

important to keep the teeth of the saw chain sharp. Follow

these helpful tips for proper saw chain sharpening:

1. For best results use a 11/64" (4.5mm) file and a file holder

or filing guide to sharpen your saw chain. This will ensure

you always get the correct sharpeningangles.

2. Place the file holder flat on the top plate and depth

gauge of thecutter.

3. Keep the correct top plate23 filing angle line of 30° on

your file guide parallel with your chain (file at 60° from

chain viewed from the side) as shownin Fig. N.

4. Sharpen cutters on one side of the chain first. File from

the inside of each cutter to the outside. Then turn your

saw around and repeat the processes (2, 3, 4) for cutters

on the other side of thechain.

NOTE: Use a flat file to file the tops of the rakers (portion

of chain link in front of the cutter) so they are about .025"

(.635 mm) below the tips of the cutters as shownin Fig. O.

5. Keep all cutter lengthsequal as shownin Fig. P.

6. If damage is present on the chrome surface of the

top plates or side plates, file back until such damage

isremoved.

CAUTION: After filing, the cutter will be sharp, use

extra caution during thisprocess.

Three Year Limited Warranty

For warranty terms, go to https://www.dewalt.com/Legal/

Warranty/3‑Year‑Limited‑Warranty.

To request a written copy of the warranty terms, contact:

Customer Service at DeWALT Industrial Tool Co., 701East

Joppa Road, Towson, MD 21286or call 1‑800‑4‑DeWALT

(1-800-433-9258).

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1‑800‑4‑DeWALT

(1-800-433-9258) for a freereplacement.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of an

insurance loss, such as fire, flood or theft, your registration

of ownership will serve as your proof ofpurchase.

• FOR YOUR SAFETY: Registering your product will allow

us to contact you in the unlikely event a safety notification

is required under the Federal Consumer SafetyAct.

• Register online at www.dewalt.com.

Repairs

The charger and batteries are notserviceable. There are no

serviceable parts inside the charger or batterypack.

WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a DeWALT factory

service center or a DeWALT authorized service center.

Always use identical replacementparts.

ENGLISH

DCCS623 TROUBLESHOOTING

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

For assistance with your product, visit our website

at www.dewalt.com for a list of service centers,

orcallDeWALT at 1‑800‑4‑DeWALT (1‑800‑433‑9258).

Problem Solution

Unit will notstart. • Check batteryinstallation.

• Check battery

chargingrequirements.

• Check that lock off is fully

pushed down prior to moving

maintrigger.

Unit shuts down

inuse.

• Chargebattery.

• Unit is being forced. Restart and

apply lesspressure.

Battery will

notcharge.

• Insert battery into charger until red

charging light illuminates.

• Plug charger into a working outlet.

Refer to Important Charging

Notes for moredetails.

• Check current at receptacle by

plugging anappliance.

• Check to see if receptacle is

connected to a light switch which

turns power off when you turn out

thelights.

• Move charger and appliance to

a surrounding air temperature

of above 40°F (4.5°C) or below

104°F (+40 °C).

Bar / Chain

overheated.

• Refer to Adjusting Chain

Tensionsection.

• Refer to

Chain Oiling

section.

Chain isloose.

• Refer to Adjusting Chain

Tensionsection.

Poor cutquality.

• Refer to

Adjusting Chain

Tension

section.

NOTE:

Excessive

tension leads to excessive wear

and reduction in life of bar and

chain. Lubricate before each

cut. Refer to

Replacing the

Saw Chain

and

Saw Chain

Sharpening

section.

Unit runs but does

notcut.

• Chain could be installed

backwards. Refer to sections for

installing and removingchain.

Unit does notoil. • Refill oilreservoir.

• Clean guide bar, sprocket

and sprocket cover. Refer to

Maintenancesection.

FRANÇAIS

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise

àl’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des radiateurs,

des cuisinières et des réfrigérateurs. Le risque de

choc électrique est plus élevé si votre corps est mis à

laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive. Ne

jamais utiliser le cordon pour transporter, tirer

ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à l’extérieur,

se servir d’une rallonge convenant à cette

application. L’utilisation d’une rallonge conçue pour

l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique est

utilisé. Ne pas utiliser d’outil électrique en cas de

fatigue ou sous l’influence de drogues, d’alcool ou

de médicaments. Un simple moment d’inattention en

utilisant un outil électrique peut entraîner des blessures

corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

AVERTISSEMENTS GÉNÉRAUX SUR LA

SÉCURITÉ DES OUTILS

AVERTISSEMENT : lisez tous les avertissements de

sécurité, toutes les instructions, les illustrations

et les caractéristiques fournis avec cet outil

électrique. Ne pas suivre toutes les instructions

comprises aux présentes peut conduire à un choc

électrique, un incendie et/ou des blessuresgraves.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN

USAGEULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sansfil).

Définitions : Symboles et mentions d'alerte

de sécurité

Cette notice d'utilisation utilise les symboles et les mentions

d'alerte de sécurité suivants afin de vous alerter sur les

situations dangereuses et les risques de blessures ou de

dégâtsmatériels.

DANGER : indique une situation de risque imminent

qui engendre, si elle n'est pas évitée, la mort ou de

gravesblessures.

AVERTISSEMENT: indique une situation de risque

potentiel qui pourrait engendrer, si elle n'est pas

évitée, la mort ou de gravesblessures.

ATTENTION: indique une situation de risque potentiel

qui peut engendrer, si elle n'est pas évitée, des

blessures bénignes oumodérées.

(Utilisé sans mention) Indique un message lié à

lasécurité.

REMARQUE: indique une pratique n'entraînant

aucun risque de blessures mais qui, si elle n'est pas

évitée, peut entraîner des dommagesmatériels.

Utilisation prévue

La DCCS623 tronçonneuse est conçue pour les applications

de tronçonnage jusqu’à 152mm (6po) de diamètre.

NE PAS utiliser en conditions humides ou en présence de

liquides ou de gaz inflammables.

Cette tronçonneuse est un outil électrique professionnel.

NE PAS laisser les enfants entrer en contact avec l’outil.

Une supervision est requise lorsque des utilisateurs

inexpérimentés utilisent cet outil.

Français (traduction de la notice d’instructions originale)

AVERTISSEMENT: lisez tous les avertissements

de sécurité et toutes les instructions. Ne pas suivre

les avertissements et les instructions peut entraîner un

choc électrique, un incendie et/ou des blessuresgraves.

AVERTISSEMENT: pour réduire le risque de blessure,

lisez le guided’utilisation.

FRANÇAIS

e ) Gardez les poignées et surfaces d’emprise propres

et libres de tout produit lubrifiant. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus faciles

àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en

tenant compte des conditions de travail et du

travail à effectuer. L’utilisation d’un outil électrique

pour toute opération autre que celle pour laquelle il a

été conçu estdangereuse.

h ) Garder vos mains et les surfaces de prise sèches,

propres et libres de graisse et de poussière. Les

mains et les surfaces de prise glissante ne permettent

pas la manutention et le contrôle sécuritaires de l’outil

dans les situationsimprévues.

5) Utilisation et entretien du bloc‑piles

a ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc‑piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de b loc‑piles.

b ) Utiliser les outils électriques uniquement avec

les blocs‑piles conçus à cet effet. L’utilisation de

tout autre bloc‑piles risque de causer des blessures ou

unincendie.

c ) Lorsque le bloc‑piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court‑circuit des bornes du bloc‑piles

risque de provoquer des brûlures ou unincendie.

d ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc‑piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc‑piles peut provoquer

des irritations ou desbrûlures.

e ) Ne pas utiliser de bloc‑piles ou outil qui a été

endommagé ou modifié. Les unités endommagées

ou modifiées peuvent avoir une réaction imprévisible

résultant en un incendie, une explosion ou un potentiel

deblessure.

f ) Ne pas exposer de bloc‑piles ou l’outil aux

flammes ou à des températures excessives.

L’exposition aux flammes ou à une température

au‑dessus de 130°C (265°F) pourrait causer

uneexplosion.

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position d’arrêt

avant de relier l’outil à une source d’alimentation

et/ou d’insérer un bloc‑piles, de ramasser ou de

transporter l’outil. Transporter un outil électrique

alors que le doigt repose sur l’interrupteur ou brancher

un outil électrique dont l’interrupteur est à la position

de marche risque de provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver son

équilibre en tout temps. Cela permet de mieux

maîtriser l’outil électrique dans les situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux‑ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

h ) Ne pas laisser votre connaissance acquise suite

l’utilisation fréquente des outils vous permettre

de baisser la garde et ignorer les principes de

sécurité de l’outil. Un acte irréfléchi peut causer une

blessure grave en une fraction deseconde.

4) Utilisation et entretien d’un

outilélectrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

b ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et doit

êtreréparé.

c ) Débranchez la fiche de la prise électrique et, si

amovible, retirez le bloc‑piles de l’outil avant

d’effectuer tout ajustement, changement et

entreposage de celui‑ci. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

La page charge ...

DeWalt DCCS623 20V Max* Pruner Manuel utilisateur

Marque: DeWalt

Modèle: DCCS623 20V Max* Pruner

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCCS623 20V Max* Pruner User manual
español: DeWalt DCCS623 20V Max* Pruner Manual de usuario

DeWalt DCCS623 20V Max* Pruner Manuel utilisateur

DeWalt DCCS623 20V Max* Pruner Manuel utilisateur

dans d''autres langues

Autres documents