Dell PowerEdge 2800 Guide de démarrage rapide

Rack Installation Guide

Guide d'installation en rack

Rack-Installationsanleitung

ラック取り付けガイド

Guía de instalación del rack

Rack Installation Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: RapidRails and VersaRails are trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names

or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

May 2004 P/N W1948 Rev. A00

Contents 1-3

Contents

CAUTION: Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 1-5

SAFETY: Rack Mounting of Systems

. . . . . . . . . . . . . . . . . 1-5

Installation Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Four-Post Rack Installation

. . . . . . . . . . . . . . . . . . . . . . . . 1-7

Before You Begin

. . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Recommended Tools and Supplies

. . . . . . . . . . . . . . . . . . 1-7

RapidRails Rack Kit Contents

. . . . . . . . . . . . . . . . . . . . 1-8

VersaRails Rack Kit Contents

. . . . . . . . . . . . . . . . . . . . 1-8

Installation Tasks

. . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Removing the Rack Doors

. . . . . . . . . . . . . . . . . . . . . . 1-9

Marking the Rack

. . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Installing the RapidRails Slide Assemblies

. . . . . . . . . . . . . . 1-12

Installing the VersaRails Slide Assemblies

. . . . . . . . . . . . . . 1-13

Installing the System in the Rack

. . . . . . . . . . . . . . . . . . . 1-14

Installing the Cable-Management Arm

. . . . . . . . . . . . . . . . 1-16

Replacing the Rack Doors

. . . . . . . . . . . . . . . . . . . . . . 1-20

Two-Post Rack Installation

. . . . . . . . . . . . . . . . . . . . . . . . 1-21

Two-Post Rack Installation Tasks

. . . . . . . . . . . . . . . . . . 1-21

Recommended Tools and Supplies

. . . . . . . . . . . . . . . . . . 1-21

Rack Kit Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

Marking the Rack

. . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

Installing the Slide Assemblies in the Rack

. . . . . . . . . . . . . . 1-24

Installing the System in the Rack

. . . . . . . . . . . . . . . . . . . 1-30

Installing the Cable-Management Arm

. . . . . . . . . . . . . . . . 1-30

Routing Cables

. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-30

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-31

1-4 Contents

Figures

Figure 1-1. RapidRails Rack Kit Contents . . . . . . . . . . 1-8

Figure 1-2. VersaRails Rack Kit Contents

. . . . . . . . . . 1-9

Figure 1-3. One Rack Unit

. . . . . . . . . . . . . . . . . . 1-10

Figure 1-4. Marking the Vertical Rails

. . . . . . . . . . . . 1-11

Figure 1-5. Installing the RapidRails Slide Assemblies

. . . . 1-12

Figure 1-6. Installing the VersaRails Slide Assemblies

. . . . 1-14

Figure 1-7. Installing the System in the Rack

(RapidRails or VersaRails)

. . . . . . . . . . . . 1-15

Figure 1-8. Installing the Cable-Management Arm

. . . . . . 1-17

Figure 1-9. Installing the Cable-Management Arm

. . . . . . 1-18

Figure 1-10. Routing the Power Cords

. . . . . . . . . . . . 1-19

Figure 1-11. Routing Cables

. . . . . . . . . . . . . . . . . 1-20

Figure 1-12. Two-Post Rack Kit Components

. . . . . . . . . 1-22

Figure 1-13. Two-Post, Open-Frame Relay Rack

Universal-Hole Spacing

. . . . . . . . . . . . . 1-23

Figure 1-14. Two-Post, Open-Frame Relay Rack

Wide-Hole Spacing

. . . . . . . . . . . . . . . 1-23

Figure 1-15. Brackets Prepared for Center-Mount

Installation

. . . . . . . . . . . . . . . . . . . 1-25

Figure 1-16. Installing the Slide Assemblies

for Center-Mount Configuration

. . . . . . . . . 1-26

Figure 1-17. Rotating the Front Mounting Bracket

for Flush-Mount Installation

. . . . . . . . . . . 1-28

Figure 1-18. Installing the Slide Assemblies

for Flush-Mount Configuration

. . . . . . . . . . 1-29

Rack Installation Guide 1-5

CAUTION: Safety Instructions

Use the following safety guidelines to help ensure your own personal safety and to help

protect your system and working environment from potential damage. For complete safety

information, see the

Product Information

Guide

.

SAFETY: Rack Mounting of Systems

Observe the following precautions for rack stability and safety.

Systems are considered to be components in a rack. Thus, "component" refers to any system

as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front and side stabilizers installed could

cause the rack to tip over, potentially resulting in bodily injury under certain circumstances.

Therefore, always install the stabilizers before installing components in the rack.

After installing system/components in a rack, never pull more than one component out of the rack

on its slide assemblies at one time. The weight of more than one extended component could

cause the rack to tip over and injure someone.

NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a rack

cabinet using the customer rack kit. The installation of your system and rack kit in any other rack

cabinet has not been approved by any safety agencies. It is your responsibility to ensure that the

final combination of system and rack complies with all applicable safety standards and local

electric code requirements. The manufacturer disclaims all liability and warranties in connection

with such combinations.

• System rack kits are intended to be installed in a rack by trained service technicians.

If you install the kit in any other rack, be sure that the rack meets the specifications.

CAUTION: Do not move racks by yourself. Due to the height and weight of the rack, a minimum

of two people should accomplish this task.

• Before working on the rack, make sure that the stabilizers are secured to the rack,

extended to the floor, and that the full weight of the rack rests on the floor. Install front

and side stabilizers on a single rack or front stabilizers for joined multiple racks before

working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the rack.

• Use caution when pressing the component rail release latches and sliding a component

into or out of a rack; the slide rails can pinch your fingers.

• After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

1-6 Rack Installation Guide

Installation Instructions

This installation guide provides instructions for trained service technicians installing one or more

systems in an open-frame relay rack or in a rack cabinet. The RapidRails™ rack kit can be installed

without tools in manufacturer’s rack cabinets that have square holes; the VersaRails™ rack kit can

be installed in most industry-standard rack cabinets that have square or round holes. The

procedures for installing both RapidRails and VersaRails rack kits are similar. One rack kit is

required for each system installed in the rack.

This guide includes procedures for the following rack kits:

• RapidRails kit in a four-post rack cabinet

• VersaRails kit in a four-post rack cabinet

• Two-post kit (installed in either center-mount or flush-mount configuration,

for 3- or 6-inch-wide racks)

For ease in troubleshooting and determining the health of your system, some rack kits include a

status-indicator cable that relays the information from the two-color status indicators on the front

and back panels to the back of the cable-management arm. For more information on these

indicators, see your system

User’s Guide

.

Before attempting this installation, you should read through this entire document carefully.

CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for

your system. Using the rack kit for another system may result in damage to the system and personal

injury to yourself and to others.

Rack Requirements for VersaRails

NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a rack that

meets the specifications of American National Standards Institute (ANSI)/Electronic Industries

Association (EIA) standard ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and

Deutsche Industrie Norm (DIN) 41494. One rack kit is required for each system that is installed in a rack.

• Do not overload the AC supply branch circuit that provides power to the rack.

The total rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any component when servicing other components in a rack.

CAUTION: Safety Instructions (continued)

Rack Installation Guide 1-7

Four-Post Rack Installation

Before attempting this installation, you should read through this entire procedure carefully.

Before You Begin

Before you begin installing your system in the rack, carefully read the safety instructions found at

the beginning of this guide, as well as the safety instructions found in your system’s

Product

Information Guide

for additional information.

CAUTION: When installing multiple systems in a rack, complete all of the procedures for the current

system before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on the casters. The cabinet has no

brakes. Use extreme caution while moving the rack cabinet. Retract the leveling feet when relocating

the rack cabinet. Avoid long or steep inclines or ramps where loss of cabinet control may occur. Extend

the leveling feet for support and to prevent the cabinet from rolling.

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in the rack.

CAUTION: You must strictly follow the procedures in this document to protect yourself as well as

others who may be involved. Your system may be very large and heavy, and proper preparation and

planning are important to prevent injury to yourself and to others. This becomes increasingly important

when systems are installed high up in the rack.

Rack Stabilizer Feet

CAUTION: Installing systems in a rack without the front and side stabilizer feet installed could cause

the rack to tip over, potentially resulting in bodily injury under certain circumstances. Therefore,

always install the stabilizer feet before installing components in the rack.

CAUTION: After installing systems in a rack, never pull more than one system out of the rack on its

slide assemblies at one time. The weight of more than one extended system could cause the rack to tip

over and cause injury.

The stabilizer feet help prevent the rack from tipping over when a system or other component is

pulled out of the rack with the slide assemblies fully extended. Refer to the documentation

provided with the rack cabinet for instructions on installing and anchoring the stabilizer feet.

Recommended Tools and Supplies

You may need the following tools and supplies to install the system in a four-post rack:

• A #2 Phillips screwdriver (for installing VersaRails slide assemblies)

• Masking tape or a felt-tip pen, for use in marking the mounting holes to be used

1-8 Rack Installation Guide

RapidRails Rack Kit Contents

The RapidRails rack kit includes the following items (see Figure 1-1):

• One pair of RapidRails slide assemblies

• One cable-management arm

• One status indicator cable (if applicable)

• Tie-wraps (not shown in Figure 1-1)

Figure 1-1. RapidRails Rack Kit Contents

VersaRails Rack Kit Contents

The VersaRails rack kit includes the following items (see Figure 1-2):

• One pair of VersaRails slide assemblies

• One cable-management arm

• One status indicator cable (if applicable)

• Eight 10-32 x 0.5-inch flange-head Phillips screws

• Tie-wraps (not shown in Figure 1-2)

NOTE: The nonmetric screws described in illustrations and in procedural steps are identified by size and

number of threads per inch. For example, a #10 Phillips-head screw with 32 threads per inch is identified

as a 10-32 screw.

slide assemblies (2)

cable-management arm

status indicator cable (if applicable)

Rack Installation Guide 1-9

Figure 1-2. VersaRails Rack Kit Contents

Installation Tasks

Installing a rack kit involves performing the following tasks in their numbered order:

1

Removing the rack doors

2

Marking the rack (if necessary)

3

Installing the slide assemblies in the rack:

• RapidRails installation

• VersaRails installation

4

Installing the system in the rack

5

Installing the cable-management arm

6

Routing cables

7

Replacing the rack doors

Removing the Rack Doors

See the procedures for removing doors in the documentation provided with your rack cabinet.

CAUTION: Because of the size and weight of the rack cabinet doors, never attempt to remove or install

them by yourself.

CAUTION: Store the two doors where they will not injure someone if the doors accidently fall over.

slide assemblies (2)

10-32 x 0.5-inch

flange-head

Phillips screw (8)

cable-management arm

status indicator cable (if applicable)

1-10 Rack Installation Guide

Marking the Rack

You must allow 2 U (88 mm, or 3.5 inches) of vertical space for each system you install in the rack.

Rack cabinets that meet EIA-310 standards have an alternating pattern of three holes per rack unit

with center-to-center hole spacing (beginning at the top hole of a 1-U space) of 15.9 mm, 15.9 mm,

and 12.7 mm (0.625 inch, 0.625 inch, and 0.5 inch) for the front and back vertical rails (see

Figure 1-3). Rack cabinets may have round or square holes.

NOTE: The vertical rails may be marked by horizontal lines and numbers in 1-U increments. If you wish,

you can make a note of the number marking on the rack’s vertical rail. It is not necessary to mark or place

tape on the rack. If you choose this method, skip ahead to the procedure "Installing the RapidRails Slide

Assemblies."

Figure 1-3. One Rack Unit

CAUTION: If you are installing more than one system, install the slide assemblies so that the first

system is installed in the lowest available position in the rack.

To mark the rack, perform the following steps:

1

Place a mark on the rack’s front vertical rails where you want to locate the bottom of the

system you are installing in the rack cabinet.

The bottom of each 1-U space is at the middle of the narrowest metal area between holes

(marked with a horizontal line on some rack cabinets—see Figure 1-4).

1 U (44 mm or 1.75 inches)

12.7 mm (0.5 inch)

15.9 mm (0.625 inch)

12.7 mm (0.5 inch)

Rack Installation Guide 1-11

2

Place a mark 88 mm (3.5 inches) above the original mark you made (or count up six holes in

a rack that meets EIA-310 standards) and mark the rack’s front vertical rails with a felt-tipped

pen or masking tape (if you counted holes, place a mark just above the top hole). This mark or

piece of tape indicates where the system’s upper edge will be located on the vertical rails

(see Figure 1-4).

Figure 1-4. Marking the Vertical Rails

tape on vertical rail

1-12 Rack Installation Guide

Installing the RapidRails Slide Assemblies

1

At the front of the rack cabinet, position one of the RapidRails slide assemblies so that

its mounting-bracket flange fits between the marks or tape you placed on the rack

(see Figure 1-5).

The top mounting hook on the slide assembly’s front mounting bracket flange should enter

the top hole between the marks you made on the vertical rails.

2

Push the slide assembly forward until the top mounting hook enters the top square hole that

you placed a mark just above on the vertical rail, and then push down on the mounting-

bracket flange until the mounting hooks seat in the square holes and the push button pops

out and clicks (see Figure 1-5).

Figure 1-5. Installing the RapidRails Slide Assemblies

front of rack

slide assembly (2)

mounting hooks (2)

push button

mounting-

bracket flange

Rack Installation Guide 1-13

3

At the back of the cabinet, pull back on the mounting-bracket flange until the top mounting

hook is in the top square hole, and then push down on the flange until the mounting hooks

seat in the square holes and the push button pops out and clicks.

4

Repeat steps 1 through 3 for the slide assembly on the other side of the rack.

NOTE: Ensure that the slide assemblies are mounted at the same position on the vertical rails

on each side of the rack.

Installing the VersaRails Slide Assemblies

1

At the front of the rack cabinet, position one of the VersaRails slide assemblies so that its

mounting-bracket flange fits between the marks or tape (or numbered location) on the rack

(see Figure 1-6).

The four holes on the front of the mounting bracket should align with four of the holes

between the marks you made on the front vertical rail.

2

Install two 10-32 x 0.5-inch flange-head Phillips screws in the mounting flange’s top hole and

the third-from-top hole to secure the slide assembly to the front vertical rail (see Figure 1-6).

3

At the back of the cabinet, pull back on the mounting-bracket flange until the mounting

holes align with their respective holes on the back vertical rail.

4

Install two 10-32 x 0.5-inch flange-head Phillips screws in the back mounting flange’s top

and third-from-top holes to secure the slide assembly to the back vertical rail.

5

Repeat steps 1 through 4 for the slide assembly on the other side of the rack.

NOTE: Ensure that the slide assemblies are mounted at the same position on the vertical rails

on each side of the rack.

1-14 Rack Installation Guide

Figure 1-6. Installing the VersaRails Slide Assemblies

Installing the System in the Rack

CAUTION: If you are installing more than one system, install the first system in the lowest available

position in the rack.

CAUTION: Never pull more than one component out of the rack at a time.

1

Pull the two slide assemblies out of the rack until they lock in the fully extended position.

CAUTION: Because of the size and weight of the system, never attempt to install the system in the slide

assemblies by yourself.

2

Lift the system into position in front of the extended slides (see Figure 1-7).

3

Place one hand on the front-bottom of the system and the other hand on the back-bottom

of the system.

front of rack

slide assembly (2)

10-32 x 0.5-inch flange-

head Phillips screw

(4 per slide assembly)

mounting-bracket flange

Rack Installation Guide 1-15

4

Tilt the back of the system down while aligning the back shoulder screws on the sides

of the system with the back slots on the slide assemblies.

5

Engage the back shoulder screws into their slots.

Figure 1-7. Installing the System in the Rack (RapidRails or VersaRails)

6

Lower the front of the system and engage the front and middle shoulder screws in their slots

(the middle slot is just behind the yellow system release latch).

When all shoulder screws are properly seated, the system locking mechanism at the front

of each slide assembly clicks and locks the system into the slide assembly.

7

Press up on the slide release latch at the side of each slide to slide the system completely

into the rack.

system locking mechanism

shoulder screw

on system

1-16 Rack Installation Guide

8

Push in and turn the captive thumbscrews on each side of the front chassis panel to secure

the system to the rack.

NOTE: To remove the system from the slide assemblies, press down on the thumbpads of the system

locking mechanism, and then pull the system forward.

Installing the Cable-Management Arm

NOTICE: The cable-management arm can only be installed on the right side of the rack cabinet (as

viewed from the back).

To install the cable-management arm on the system, perform the following steps:

1

Facing the back of the rack cabinet, locate the latch on the end of the slide assembly.

2

Push the tab on the back end of the cable-management arm into the latch on the end of

the slide assembly (see Figure 1-8).

The latch clicks when locked.

3

Push the tab on the front end of the cable-management arm into a mating latch on the inner

segment of the slide assembly (see Figure 1-8).

The latch clicks when locked.

Rack Installation Guide 1-17

Figure 1-8. Installing the Cable-Management Arm

4

If applicable, install the system status indicator cable plug into its connector (see Figure 1-9).

5

Open the wire covers on the cable-management arm by lifting the center of the wire over the

top of the embossed round button on the front of the forward part of the arm and lifting the

wire over the top of a similar round button on the back part of the arm.

The wire cover swings open to enable cables to be routed within the arm.

6

Route the system status indicator end of the cable through the cable-management arm, and

install the indicator in its slot at the back end of the cable-management arm (see Figure 1-9).

latch on inner

segment of slide

assembly

cable-management arm

latch on end of slide

assembly

tab on front end

tab on back end

1-18 Rack Installation Guide

Figure 1-9. Installing the Cable-Management Arm

7

Connect the power cords to their receptacles on the back panel (see Figure 1-10).

NOTE: Use the strain-relief loops (if available) on the back of the power supplies to provide strain

relief for the power cables.

system status

indicator cable plug

wire covers in

open position

system status indicator

La page est en cours de chargement...

Dell PowerEdge 2800 Guide de démarrage rapide

Dell PowerEdge 2800 Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents