Whirlpool AKR 637 WH Program Chart

Whirlpool
Marque
Whirlpool
Modèle
AKR 637 WH
Catégorie
Hottes
Taper
Program Chart

Ce manuel convient également à

AKR 637
5019 100 75150
INSTALLATION SHEET
Minimum height above cooker: 65cm (electric cookers), 75cm (gas, gas oil or coal
cookers). To install follow points (1
Ö
2
Ö
3
Ö
.....). Do not connect the appliance to
the electrical power supply until installation is completed. The power plug of the
hood must be inserted into a socket that complies with current regulations and is
located in an easily accessible zone. If the hood is not fitted with a plug (direct
connection to the power supply), fit a two-pole switch in compliance with
regulations, with minimum break distance between contacts of 3 mm
(easily accessible).
FICHE D’INSTALLATION
Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique), 75 cm
(cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la numérotation
(1
Ö
2
Ö
3
Ö
.....). Ne branchez pas l’appareil tant que l’installation n’est pas
terminée. La fiche de la hotte doit être branchée dans une prise conforme aux
normes en vigueur placée dans un endroit accessible. Si la hotte est dépourvue
de fiches (branchement direct sur le réseau) appliquez un interrupteur bipolaire
conforme aux normes avec une distance des contacts en ouverture non
inférieure à 3mm (accessible).
GB
F
5019 100 75150
AKR 637
a
b
c
7
7
1
2
2
3
6
6
4
5
8
8
9
9
A
F
Not provided
Non fourni
A
EXTRACTOR VERSION!
A
VERSION ASPIRANTE!
F
FILTER VERSION!
F
VERSION FILTRANTE!
AKR 637
5019 100 75150
1.
Control panel.
2.
Grease filters (behind the extractor grilles).
3.
Lighting unit.
4.
Pull-out steam deflector.
Removing the extractor grilles and
washing the grease filter:
1.
Unplug the appliance or disconnect the mains
power supply.
2.
Pull out the steam deflector
(a - Fig. 1)
.
3.
Remove the extractor grilles
(b - Fig. 1, c - Fig. 2)
.
4.
Remove the device securing the grease filter
(d - Fig. 2)
.
5.
Remove the dirty grease filter.
6.
After cleaning the grease filter, remount in
reverse order ensuring that the entire
extraction surface is covered (First fit the front
filter, then replace the steam deflector and
lastly fit the rear filter).
Fitting or renewing the carbon filter:
1.
Unplug the appliance or disconnect the mains
power supply.
2.
Pull out the steam deflector
(a - Fig. 1)
.
3.
Remove the extractor grilles
(b - Fig. 1, c - Fig. 2
).
4.
If the carbon filters are already mounted (two
filters covering the motor protection grille) and
need renewing, turn the central handle
(e - Fig. 3)
anticlockwise until the filters
release.
5.
If the carbon filters are not already fitted,
locate one on each side to cover both motor
protection grilles, then turn the central handle
(e - Fig. 3)
of the filters clockwise.
6.
Refit the extractor grille.
Replacing bulbs
1.
Unplug the appliance or disconnect the mains
power supply.
2.
Pull out the steam deflector
(a - Fig. 1)
.
3.
Open the rear extractor grille
(b - Fig. 1)
.
4.
Remove the burnt-out bulb.
Replace using 40W max (E14) bulbs only.
5.
Refit the extractor grille.
CONTROL PANEL
A.
Speed selector switch.
B.
Light switch.
2
3
1
4
O123
OI
CLOSED
OPEN
CLOSED
OPEN
b
a
b
b
e
e
Fig. 1
Fig. 2
Fig. 3
A
small amount of steam and fumes
c
d
B
PRODUCT SHEET
large amount of steam and fumes
medium amount of steam and fumes
GB F
  • Page 1 1
  • Page 2 2
  • Page 3 3

Whirlpool AKR 637 WH Program Chart

Whirlpool
Marque
Whirlpool
Modèle
AKR 637 WH
Catégorie
Hottes
Taper
Program Chart
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents