Hilti 3553051 Manuel utilisateur

Marque: Hilti

Modèle: 3553051

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

TE 50

TE 50-AVR

English 1

Français 14

Español 28

Português 42

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

TE 50

TE 50-AVR

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Notice d'utilisation originale . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 28

pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in this documentation and

on the product.

• Always keep the operating instructions with the product and make sure

that the operating instructions are with the product when it is given to

other persons.

1.2 Explanation of signs used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the

product. The following signal words are used in combination with a symbol:

DANGER! Draws attention to imminent danger that will lead to seri-

ous personal injury or fatality.

WARNING! Draws attention to a potential hazard that could lead to

serious personal injury or fatality.

CAUTION! Draws attention to a potentially dangerous situation that

could lead to minor personal injury or damage to the equipment or

other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use

Instructions for use and other useful information

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the

beginning of these operating instructions.

The numbering reflects the sequence of operations shown in the

illustrations and may deviate from the steps described in the text.

Item reference numbers are used in the overview illustrations and

refer to the numbers used in the product overview section.

These characters are intended to specifically draw your attention to

certain points when handling the product.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

2 English

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

Drilling with hammer action (hammer drilling)

Chiseling

Chisel positioning

Protection class II (double-insulated)

Revolutions per minute

Rated speed under no load

Diameter

Wireless data transfer

1.4 Product information

Hilti products are designed for professional use and may be operated, ser-

viced and maintained only by trained, authorized personnel. This personnel

must be informed of any particular hazards that may be encountered. The

product and its ancillary equipment can present hazards if used incorrectly

by untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are stated on the rating plate.

▶ Write down the serial number in the table below. You will be required to

state the product details when contacting Hilti Service or your local Hilti

organization to inquire about the product.

Product information

Combihammer TE 50AVR

Generation 03

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here

complies with the applicable directives and standards. A copy of the

declaration issued by the certification department can be found at the end

of this documentation.

The technical documentation is filed and stored here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916

Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

English 3

Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

▶ Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce risk of electric

shock.

▶ Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk

of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personal

injury.

▶ Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

4 English

▶ Prevent unintentional starting. Ensure the switch is in the off‐position

before connecting to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your finger on the switch

or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

▶ Disconnect the plug from the power source and/or the battery

pack from the power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

▶ Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

▶ Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly maintained power

tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and

the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

English 5

Service

▶ Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

2.2 Hammer safety warnings

▶ Wear ear protectors. Exposure to noise can cause hearing loss.

▶ Use auxiliary handles, if supplied with the tool. Loss of control can

cause personal injury.

▶ Hold power tool by insulated gripping surfaces, when performing an

operation where the cutting accessory may contact hidden wiring

or its own cord. Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give the operator

an electric shock.

2.3 Additional safety instructions

Personal safety

▶ Use the product only when it is in technically faultless condition.

▶ Never tamper with or modify the power tool in any way.

▶ Apply appropriate safety measures at the opposite side of the workpiece

in work that involves breaking through. Parts breaking away could fall out

and / or fall down causing injury to other persons.

▶ Always hold the power tool with both hands on the grips provided. Keep

the grips clean and dry.

▶ Always grip the side handle at its outermost end. When drilling and

screwdriving, the grip of the power tool may be deflected laterally (the

power tool tends to pivot about its own axis).

▶ Avoid touching rotating parts – risk of injury!

▶ Wear suitable protective glasses, a hard hat, ear protection, protective

gloves and light respiratory protection while using the power tool.

▶ Wear protective gloves also when changing the accessory tool. Touching

the accessory tool presents a risk of injury (cuts or burns).

▶ Wear eye protection. Flying fragments present a risk of injury to the body

and eyes.

▶ Before beginning the work, check the hazard classification of the dust

that will be produced. Use an industrial vacuum cleaner with an officially

approved protection classification in compliance with locally applicable

dust protection regulations.

▶ Use a dust removal system and suitable vacuum cleaner whenever

possible. Dust from materials, such as paint containing lead, some

wood species, concrete/masonry/stone containing silica, and minerals as

well as metal, may be harmful.

▶ Make sure that the workplace is well ventilated and, where necessary,

wear a respirator appropriate for the type of dust generated. Contact with

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

6 English

or inhalation of the dust may cause allergic reactions and/or respiratory

or other diseases to the operator or bystanders. Certain kinds of dust

are classified as carcinogenic such as oak and beech dust, especially

in conjunction with additives for wood conditioning (chromate, wood

preservative). Material containing asbestos may be handled only by

specialists.

▶ Take breaks between working and do physical exercises to improve the

blood circulation in your fingers. Exposure to vibration during long periods

of work can lead to disorders of the blood vessels and nervous system in

the fingers, hands and wrists.

Electrical safety

▶ Before beginning work, check the working area for concealed electric

cables or gas and water pipes. External metal parts of the power tool may

become live, presenting a risk of electric shock, if you damage an electric

cable accidentally.

Careful handling and use of power tools

▶ Switch the power tool off if the accessory tool sticks and stalls. The power

tool may be deflected laterally.

▶ Wait until the power tool stops completely before you lay it down.

3 Description

3.1 Overview of the product 1

Chuck

;

Depth gauge

Function selector switch

Control switch

Service indicator

(

AVR

)

Supply cord

Side handle

3.2 Version with detachable supply cord 2

Lockbutton

;

Connector on electric tool

Supply cord with keyed, re-

leasable plug connector

3.3 Intended use

The product described is an electrically-powered combihammer with pneu-

matic hammering mechanism. It is designed for drilling in concrete, masonry,

wood and metal. The product can also be used for light to medium-duty

chiseling on masonry and surface finishing work on concrete.

▶ Operation is permissible only when connected to a power source providing

a voltage and frequency in compliance with the information given on the

type identification plate.

3.4 Possible misuse

• This product is not suitable for working on hazardous materials.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

English 7

• This product is not suitable for working in a damp environment.

3.5 Active Vibration Reduction

The tool is equipped with an Active Vibration Reduction (AVR) system which

reduces vibration noticeably.

3.6 Quick-release chuck (accessory)

The quick-release chuck makes it possible to change accessory tools

quickly, without need for a chuck key (keyless system). It is suitable for

accessory tools with a cylindrical or hexagonal shank, such as drill bits for

wood and metal, or mixing paddles, which are used in the rotary-only mode

(without hammering action) .

3.7 Service indicator

The product has an LED service indicator.

Status Meaning

Service indicator shows • The carbon brushes have reached

the end of their life. Only a few

hours of residual runtime are left

before automatic shutdown takes

place.

• Bring the product to Hilti Service

(recommended) or replace the

carbon brushes.

Service indicator flashes • The product is faulty. Have the

combihammer repaired by Hilti

Service.

3.8 Items supplied

Combihammer, side handle, operating instructions.

Other system products approved for use with this product can be found at

your local Hilti Store or online at: www.hilti.group / www.hilti.com.

4 Technical data

Note

For rated voltage, rated current, frequency and/or input power, refer to

the country-specific type identification plate.

If the device is powered by a generator or transformer, the generator or

transformer’s power output must be at least twice the rated input power

shown on the rating plate of the device. The operating voltage of the

transformer or generator must always be within +5 % and -15 % of the rated

voltage of the device.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

8 English

TE 50AVR

Weight (without supply cord)

13.4 lb

(6.1 kg)

Ø hammer drill bits

1/2 in …1 1/4 in

Ø hammer drill bits

12 mm …32 mm

Ø drill bits for wood

1/4 in …1 3/8 in

Ø drill bits for wood

6 mm …35 mm

Ø drill bits for metal

1/4 in …1/2 in

Ø drill bits for metal

6 mm …13 mm

5 Operation

5.1 Preparations at the workplace

CAUTION

Risk of injury! Inadvertent starting of the product.

▶ Unplug the supply cord before making adjustments to the power tool

or before changing accessories.

Observe the safety instructions and warnings in this documentation and on

the product.

5.1.1 Fitting the side handle 3

1. Release the side handle clamping band by turning the handle grip.

2. Slide the side handle clamping band over the chuck from the front and

into the recess provided.

3. Bring the side handle into the desired position.

4. Tighten the side handle clamping band by turning the handle grip.

5.1.2 Fitting the depth gauge (optional) 4

1. Release the side handle clamping band by turning the handle grip.

2. Slide the depth gauge from the front into the 2 guide holes provided.

3. Tighten the side handle clamping band by turning the handle grip.

◁ The depth gauge is fitted. To set the drilling depth:

4. Release the screw at the depth gauge.

5. Adjust the depth gauge to the desired drilling depth.

6. Tighten the screw at the depth gauge.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

English 9

5.1.3 Fitting/removing the accessory tool 5

CAUTION

Risk of injury! The accessory tool gets hot during use.

▶ Wear protective gloves when changing the accessory tool.

▶ Do not place the hot accessory tool on readily flammable materials.

1. Apply a little grease to the connection end of the accessory tool.

2. Push the accessory tool into the chuck as far as it will go (until it engages).

◁ The product is ready for use.

3. Pull the chuck back as far as it will go and remove the accessory tool.

Note

Use only the recommended grease supplied by Hilti. Use of unsuit-

able grease may cause damage to the product.

5.2 Types of work

Warning! Risk of damage!

▶ Operation of the direction of rotation and/or function selector switch

while the tool is running may result in damage to the tool.

▶ Do not operate this switch while the tool is running.

Observe the safety instructions and warnings in this documentation and on

the product.

5.2.1 Drilling with hammering action (hammer drilling) 6

1. Set the function selector switch to the “Hammer drilling” position .

2. Press the drill bit against the work surface.

3. Press the control switch.

◁ The product starts.

5.3 Chisel positioning 7

CAUTION

Risk of injury! Loss of control over the chisel direction.

▶ Do not operate the tool when the selector switch is set to “Chisel

positioning”. Turn the function selector switch until it engages in the

“Chiseling” position.

Note

The chisel can be adjusted to 24 different positions (in 15° increments).

This ensures that flat chisels and shaped chisels can always be set to

the optimum working position.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

10 English

1. Set the function selector switch to the “Chisel positioning” position .

2. Rotate the chisel to the desired position.

3. Turn the function selector switch until it engages in the “Chiseling”

position.

◁ The product is ready for use.

5.3.1 Chiseling 8

▶ Set the function selector switch to the “Chiseling” position .

5.3.2 Switching sustained operation on and off 9

Note

When chiseling, the on/off switch can be locked in the “on” position.

1. Push the lockbutton for continuous operation forward.

2. Press the on/off switch as far as it will go.

◁ The product then runs in sustained operating mode.

3. Push the lockbutton for continuous operation back.

◁ The product switches off.

6 Detachable supply cord

6.1 Connecting the detachable supply cord

CAUTION

Risk of injury! Due to leakage current as a result of dirty contacts.

▶ Connect the detachable electric connector to the electric tool only

when it is clean and dry and when the supply cord is unplugged from

the power outlet.

1. Push the keyed, detachable electric plug connector into the socket as far

as it will go, until it is heard to engage.

2. Plug the supply cord into the power outlet.

6.2 Disconnecting the detachable supply cord

1. Unplug the supply cord from the power outlet.

2. Press the release button and pull the keyed, detachable electric plug

connector out of the socket.

3. Pull the supply cord connector out of the power tool.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

English 11

7 Care and maintenance

WARNING

Danger of electric shock! Carrying out care and maintenance while the

supply cord is connected to the power outlet presents a risk of serious

injuries including burns.

▶ Always unplug the supply cord before carrying out all care and

maintenance tasks.

Care

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as they can attack the plastic parts.

Maintenance

• At regular intervals, check all visible parts and the controls for signs of

damage and make sure that they all function correctly.

• Do not operate the power tool if signs of damage are found or if parts

malfunction. Have damage repaired immediately by Hilti Service.

• After cleaning and maintenance, refit all guards or protective devices and

check that they function correctly.

Note

To help ensure safe and reliable operation, use only genuine Hilti spare

parts and consumables. Spare parts, consumables and accessories

approved by Hilti for use with the product can be found at your local

Hilti Store or online at: www.hilti.group / www.hilti.com

8 Transport and storage

• Do not transport electric tools with accessory tools fitted.

• Always unplug the supply cord before storing an electric tool or appliance.

• Store tools and appliances in a dry place where they cannot be accessed

by children or unauthorized persons.

• Check electric tools or appliances for damage after long periods of

transport or storage.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable

to remedy the problem by yourself, please contact Hilti Service.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

12 English

Trouble or fault Possible cause Action to be taken

The power tool

doesn’t start.

Interruption in the elec-

tric supply.

▶ Plug in another electric

tool or appliance

and check whether it

works.

The electronic restart

interlock is activated

after an interruption in

the electric supply.

▶ Switch the power tool

off and then on again.

No hammering ac-

tion.

The power tool is too

cold.

▶ Bring the tip of the drill

bit into contact with

the working surface,

switch the rotary

hammer on and allow

it to run. If necessary,

repeat the procedure

until the hammering

mechanism begins to

operate.

The combihammer

doesn’t achieve full

power.

The gauge (cross sec-

tion) of the extension

cord conductors is inad-

equate.

▶ Use an extension cord

with an adequate con-

ductor cross section.

The voltage provided by

the electric supply is too

low.

▶ Connect the combi-

hammer to a different

electric supply.

The drill bit doesn’t

rotate.

The function selector

switch is not engaged or

is in the “Chiseling” or

“Chisel adjustment”

position.

▶ Set the function

selector switch to

the “Hammer drilling”

position .

The drill bit can’t be

released.

The chuck is not pulled

back fully.

▶ Pull the chuck back

as far as it will go and

remove the accessory

tool.

The side handle is not

fitted correctly.

▶ Release the side

handle and refit it

correctly so that the

clamping band and

side handle engage in

the recess.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

English 13

Trouble or fault Possible cause Action to be taken

The service indicator

lights after changing

the carbon brushes.

The contact surfaces are

not yet run in.

▶ Run in the carbon

brushes by allowing

the power tool to run

under no load for at

least 1 minute without

interruption.

10 Disposal

Most of the materials from which Hilti tools and appliances are manu-

factured can be recycled. The materials must be correctly separated before

they can be recycled. In many countries, your old tools, machines or appli-

ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti

representative for further information.

▶ Disposal of electric tools or appliances together with household

waste is not permissible.

11 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about

the warranty conditions.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

14 Français

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service.

C'est la condition préalablement requise pour assurer la sécurité du travail

et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la

présente documentation ainsi que celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement

le transmettre à des tiers avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du

produit. Les termes de signalisation suivants sont utilisés en combinaison

avec un symbole :

DANGER ! Pour un danger imminent qui peut entraîner de graves

blessures corporelles ou la mort.

AVERTISSEMENT ! Pour un danger probable qui peut entraîner de

graves blessures corporelles ou la mort.

ATTENTION ! Pour attirer l'attention sur une situation pouvant pré-

senter des dangers entraînant des blessures corporelles légères ou

des dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Ces chiffres renvoient à l'illustration correspondante au début du

présent mode d'emploi.

La numérotation détermine la séquence des étapes de travail dans

l'image et peut se différencier de celles des étapes de travail dans le

texte.

Les numéros de position sont utilisés dans l'illustration Vue d’en-

semble et renvoient aux numéros des légendes dans la section Vue

d'ensemble du produit.

Ce signe doit inviter à manier le produit en faisant particulièrement

attention.

Printed: 15.09.2017 | Doc-Nr: PUB / 5283567 / 000 / 01

La page charge ...

Hilti 3553051 Manuel utilisateur

Marque: Hilti

Modèle: 3553051

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

español: Hilti 3553051 Manual de usuario
português: Hilti 3553051 Manual do usuário

Hilti 3553051 Manuel utilisateur

Hilti 3553051 Manuel utilisateur

dans d''autres langues

Documents connexes