Skil SR6604B-10 Le manuel du propriétaire

Marque: Skil

Modèle: SR6604B-10

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

20V Brushed Random Orbital Sander

Ponceuse à action orbitale aléatoire à balais de 20 V

Lijadora de órbita al azar con escobillas de 20 V

1-877-SKIL-999

www.skil.com

Model/ Modelo/ Modèle: SR6604B-00

TABLE OF CONTENTS

General Power Tool Safety Warnings .............................3-5

Additional Safety Warnings .......................................5

Symbols .....................................................6-9

Get to Know Your Random Orbital Sander .........................10

Speciﬁcations .................................................10

Operating Instructions .......................................11-14

Maintenance ..................................................15

Troubleshooting ................................................16

Limited Warranty of SKIL Consumer Tools ..........................17

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other

construction activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool. Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is earthed or

grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs, alcohol

or medication. A moment of inattention while operating power tools may result in serious

personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before connecting

to power source and/or battery pack, picking up or carrying the tool. Carrying power

tools with your nger on the switch or energising power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, and clothing

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving

parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles. A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for safe handling and control of the tool in

unexpected situations.

Battery tool use and care

Recharge only with the charger specied by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs. Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modied. Damaged or modied

batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.

Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or

temperature above 265 °F may cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the

temperature range specied in the instructions. Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs. Service of battery packs should only be performed

by the manufacturer or authorized service providers

ADDITIONAL SAFETY WARNINGS

Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

Your tool is equipped with a dust canister, empty it frequently, after completion of

sanding and before storing the sander. Be extremely careful of dust disposal, materials in

ne particle form may be explosive. Do not throw sanding dust on an open re. Combustion

from mixture of varnishes, lacquers, polyurethane, oil or water with dust particles can occur if

there is a static discharge, spark introduced in the box, or excessive heat.

Always wear eye protection and a dust mask for dusty applications and when sanding

overhead. Sanding particles can be absorbed by your eyes and inhaled easily and may cause

health complications.

Do not wet sand with this sander. Liquids entering the motor housing is an electrical shock

hazard.

Do not use abrasive disc intended for larger sanding pads. Larger abrasive disc will

extend beyond the sanding pad causing snagging, tearing of the paper or kick-back. Extra

paper extending beyond the sanding pad can also cause serious lacerations.

Keep handles dry, clean and free from oil and grease. Slippery hands cannot safely control

the power tool.

Develop a periodic maintenance schedule for your tool. When cleaning a tool be careful

not to disassemble any portion of the tool since internal wires may be misplaced or

pinched or safety guard return springs may be improperly mounted. Certain cleaning

agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate

injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to

equipment or other property damage if they are not followed. Each message is preceded by

the word “NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not

followed.

WARNING

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always

use eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II tool

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

Symbol Name Designation/Explanation

Read manual symbol Alerts user to read manual

Wear eye protection symbol Alerts user to wear eye protection

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on

your tool. Please study them and learn their meaning. Proper interpretation of these symbols

will allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

GET TO KNOW YOUR RANDOM ORBITAL SANDER

20V Brushed Random Orbital Sander

Fig. 1

On/off Switch

Backing Pad

Variable-Speed Dial

Abrasive Disc

Ventilation Openings

Microlter

Dust Canister

SPECIFICATIONS

General

Rated Voltage 20V d.c.

No-load Speed 7000-11000rpm

Pad Diameter 5” (125mm)

Abrasive Disc Diameter 5” (125mm)

Orbit Diameter 1/8”(3.0mm)

Recommended working temperature 14~104°F (-10~40

Recommended storage temperature 32~104°F (0~40

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due to

a short circuit, never immerse your tool, battery pack, or charger in

uid or allow a uid to ow inside them. Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing products, etc. can cause a

short circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced. Use of this product with damaged or missing

parts could result in serious personal injury.

WARNING

Do not attempt to modify this tool or create accessories not

recommended for use with this tool. Any such alteration or modication

is misuse and could result in a hazardous condition leading to possible serious injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when assembling

parts.

This brushed random orbital sander must be used only with the battery packs and

chargers listed below:

Battery Pack

Charger

2Ah 2Ah 2.5Ah 4Ah 5Ah

SKIL

BY519701

SKIL

BY519702

SKIL

BY519703

SKIL

BY519601

SKIL

BY519603

SKIL

SC535801

SKIL

QC536001

NOTICE: Please refer to the battery pack and charger manuals for detailed operating

information.

To Attach/Detach Battery Pack

To attach the battery pack: Align the raised rib on the battery pack with the grooves on the

tool, and then slide the battery pack onto the tool (Fig. 2).

To detach the battery pack: Depress the battery-release button, located on the front of the

battery pack, to release the battery pack. Pull the battery pack out and remove it from the

tool (Fig. 3).

Fig. 2

Fig. 3

NOTICE: When placing the battery pack on the tool, be sure that the raised rib on the battery

pack aligns with the groove inside the tool and that the latches snap into place properly.

Improper attachment of the battery pack can cause damage to internal components.

WARNING

Always switch off the tool before attaching or detaching of the

battery pack.

Attaching Abrasive Discs

Place the sander upside down on a at

surface. Remove any dust or debris from the

backing pad. Align the holes of the abrasive

disc with the holes in the backing pad and

rmly press the abrasive disc against the

backing pad to ensure a good attachment

(Fig. 4).

Turning the Sander On/Off

To turn on the sander, depress the side of

the On/Off switch marked “I”. To turn it off,

depress the side of the On/Off switch marked

“O” (Fig. 5).

Variable-speed Dial

The variable-speed feature on this sander

allows you to match the proper speed to the

material being sanded.

The variable-speed dial is used to adjust the

speed of the tool. Turn the dial to increase

or decrease the speed of the tool. Position

“1” selects the slowest speed; position “6”

selects the fastest speed. Adjust the speed for

optimum performance (Fig. 6).

Fig. 4

Fig. 5

Fig. 6

Microfilter Dust Canister

The integrated dust-extraction system collects sanding dust in the canister supplied with

your sander. For maximum efciency, the dust canister should be emptied frequently during

operation.

WARNING

Your tool is equipped with a dust canister; empty it frequently during

use, after completion of sanding, and before storing the sander. Be

extremely careful of dust disposal; materials in ne-particle form may be explosive. Do not

throw sanding dust on an open fire. Combustion from mixtures of dust particles with

varnishes, lacquers, polyurethane, oil, or water can occur if there is a static discharge, a

spark introduced in the canister, or excessive heat.

Installing and Removing the Dust

Canister

To install the dust canister, align the slot on

the dust canister with the rib on the tool, and

then push the dust canister onto the tool until

it locks into place (Fig. 7).

To remove the dust canister, simply pull the

dust canister away from the tool.

Cleaning and Emptying the Dust

Canister

After removing the dust canister, remove

the backing cover of the dust canister by

depressing the two latches on the cover

(Fig. 8).

Knock excess dust out of the dust canister

or remove the dust with your ngers or a soft

brush (not included). You may notice that not

all the dust has come out of the canister. This

will not affect sanding performance, but will

reduce dust-collection efciency.

NOTE: Do not wash the micro lter with soap

and water. Dust may become more rmly

lodged in the pores, which will reduce dust

collection, and damage the micro lter.

Fig. 7

Fig. 8

Micro Filter

Backing Cover

Sanding Tips

Aluminum oxide, silicon carbide, or other

synthetic abrasives are recommended for

power sanding. Natural abrasives, such as int

or garnet sheets, are too soft for economical

use in power sanding; the uniform spacing

between grains minimizes lling or loading.

High quality aluminum oxide sheets with heavy

backing, sand faster and last longer.

Some applications, such as plastics, glass, or

stone require silicon carbide discs, which have

very sharp cutting edges.

For best results, use sanding accessories

that are of superior quality and are carefully

selected to produce professional quality results

with your sander.

The following are recommended abrasive sheets and applications:

1. Coarse Grit: For rough wood sanding.

2. Medium Grit: For general wood sanding.

3. Fine Grit: For smoothing wood or plaster patches.

4. Extra Fine Grit: For nal sanding bare wood and smoothing old paint.

With the workpiece rmly secured, turn the tool on as described above. Contact the work with

the tool only after the sander has reached its full, selected speed. Remove the sander from

the work before switching the tool off. Operating your sander in this manner will prolong the

switch and motor life and greatly increase the quality of your work.

Move the sander in long, steady strokes, parallel to the grain, and use a slight lateral motion

to overlap the strokes by as much as 75%. DO NOT apply excessive pressure — let the tool

do the work. Excessive pressure will result in poor handling, vibration, and unwanted sanding

marks (Fig. 9).

If the surface is rough, begin with coarser grits and then complete the surfacing with medium

and ne abrasives. Because the random orbit action is so effective, it is often possible to

begin sanding with a medium grit disc and go directly to ne nishing. To avoid uneven

results, do not skip more than one grit size when going from coarser to ner grits, and do not

sand in one area for too long. When the job is completed, release switch, and gently lift the

tool from the work surface at the same time.

Fig. 9

Workpiece

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components which could

cause a serious hazard. We recommend that all tool service be performed by a SKIL

Factory Service Center or Authorized SKIL Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an

authorized service center for assistance.

Carbon Brushes

The brushes and commutator in your tool have been engineered for many hours of

dependable service. To maintain peak efficiency of the motor, we recommend every two

to six months the brushes be examined. Only genuine SKIL replacement brushes specially

designed for your tool should be used.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air.

Always wear safety goggles when cleaning tools with compressed

air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and household detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive

agents.

TROUBLE SHOOTING

Problem Cause Remedy

Tool will not start 1. Battery pack is depleted. 1. Charge the battery.

2. Tool is over-loaded. 2. Turn off the tool and then try

again.

3. Battery pack is over

temperature.

3. Turn off the tool and allow

the battery pack to cool

under air ow.

4. Battery pack is not installed

properly.

4. Conrm that the battery is

locked and secured to the

tool.

5. Burned out switch. 5. Have the switch replaced by

an Authorized SKIL Service

Center or Service Station.

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY- LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration can

be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will

apply for a duration of three years for tools. All batteries and chargers will remain under the

two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty

and, to the extent permitted by law, any warranty or condition implied by law, shall be the

repair or replacement of parts, without charge, which are defective in material or workmanship

and which have not been misused, carelessly handled, or repaired by persons other than

Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must

return the complete product, transportation prepaid, to any SKIL Factory Service Center or

Authorized Service Station. For Authorized SKIL Power Tool Service Stations, please visit

www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR

SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING BELTS, GRINDING

WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE TO

SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME STATES IN

THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG

AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING

FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME

CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT

APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO

PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

05/20

TABLE DES MATIÈRES

Avertissements de sécurité généraux relatifs aux

outils électriques ............................................19-21

Avertissements de sécurité supplémentaires ....................21-22

Symboles ..................................................23-26

Apprenez à connaître votre ponceuse à orbite aléatoire ..............27

Caractéristiques techniques .....................................27

Mode d’emploi ..............................................28-31

Entretien ......................................................32

Dépannage ....................................................33

Garantie limitée de l’outil SKIL .................................34-35

AVERTISSEMENT

•

La poussière créée pendant le ponçage, le sciage, le polissage, le perçage et d’autres

activités liées à la construction peut contenir des produits chimiques reconnus par l’État

de la Californie comme étant la cause de cancer, d’anomalies congénitales et d’autres

problèmes liés aux fonctions reproductrices. Voici des exemples de ces produits chimiques :

–

Du plomb provenant de peintures à base de plomb;

–

– de la silice cristalline provenant de la brique, du ciment ou d’autres matériaux de

maçonneries;

–

De l’arsenic et du chrome provenant du bois d’œuvre traité avec un produit chimique.

•

Les risques liés à l’exposition à ces produits varient selon le nombre de fois où vous

pratiquez ces activités. Pour réduire votre exposition à ces produits chimiques :

–

Travaillez dans un endroit bien ventilé;

–

Munissez-vous de l’équipement de sécurité approuvé tel que des masques antipoussières

conçus spécialement pour ltrer les particules microscopiques;

–

Évitez l’exposition prolongée à la poussière causée par le ponçage mécanique, le sciage, le

polissage, le perçage et d’autres activités liées à la construction; Portez un équipement de

protection et lavez à l’eau et au savon toutes les parties exposées. Les poussières pénétrant

dans votre bouche ou dans vos yeux et les poussières se déposant sur votre peau peuvent

causer l’absorption de produits chimiques dangereux.

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX RELATIFS AUX

OUTILS ÉLECTRIQUES

AVERTISSEMENT

Lisez tous les avertissements et toutes les instructions,

illustrations et spécications fournis avec cet outil

électrique. Le non-respect des consignes de sécurité ci-dessous peut occasionner un choc

électrique, un incendie ou des blessures graves.

CONSERVEZ TOUS LES AVERTISSEMENTS ET LES INSTRUCTIONS

AFIN DE POUVOIR VOUS Y RÉFÉRER ULTÉRIEUREMENT.

L’expression « outil électrique » utilisée dans les avertissements correspond aux outils

électriques alimentés sur secteur (à l) ou alimentés par piles (sans l).

Mesures de sécurité dans l’aire de travail

Gardez l’aire de travail propre et bien éclairée. Une aire de travail sombre ou en désordre

augmente les risques d’accident.

N’utilisez pas d’outils électriques dans un endroit présentant un risque d’explosion,

par exemple en présence de liquides, de gaz ou de poussières inammables. Les

outils électriques produisent des étincelles susceptibles d’enammer ces poussières ou ces

vapeurs.

Maintenez les enfants et les observateurs à l’écart lorsque vous manipulez l’outil

électrique. Une distraction peut vous faire perdre la maîtrise de l’outil.

Consignes de sécurité relatives à l’électricité

Les ches des outils électriques doivent correspondre à la prise. Ne modiez jamais la

che de quelque façon que ce soit. N’utilisez pas d’adaptateur avec les outils électriques

mis à la terre. L’utilisation de ches non modiées dans les prises compatibles réduit les

risques de choc électrique.

Évitez de toucher à des surfaces mises à la terre, par exemple un tuyau, un radiateur,

une cuisinière ou un réfrigérateur. Le contact du corps avec une surface mise à la terre

augmente les risques de choc électrique.

N’exposez pas les outils électriques à la pluie ni à tout environnement humide.

L’infiltration d’eau dans un outil électrique augmente les risques de choc électrique.

N’utilisez pas le cordon d’alimentation de façon à l’endommager. Ne transportez jamais

un outil électrique en le tenant par son cordon et ne tirez jamais sur le cordon pour le

débrancher. Tenez le cordon d’alimentation éloigné des sources de chaleur, de l’huile,

des objets coupants et des pièces mobiles. Les risques de choc électrique sont plus élevés

si le cordon d’alimentation est endommagé ou emmêlé.

Lorsque vous utilisez un outil électrique à l’extérieur, utilisez une rallonge conçue pour

être utilisée à l’extérieur. Ce type de rallonge réduit les risques de choc électrique.

Si vous n’avez d’autre choix que d’utiliser un outil électrique dans un endroit humide,

utilisez une alimentation protégée par un disjoncteur différentiel. L’utilisation d’un

disjoncteur différentiel réduit les risques de choc électrique.

Sécurité personnelle

Soyez vigilant, prêtez attention à ce que vous faites et usez de votre jugement lorsque

vous utilisez un outil électrique. N’utilisez pas un outil électrique lorsque vous êtes

fatigué ou sous l’effet de drogues, d’alcool ou de médicaments. Un moment d’inattention

pendant que vous utilisez des outils électriques peut occasionner des blessures graves.

Utilisez un équipement de protection. Portez toujours des lunettes de sécurité. Le port

d’équipement de protection, comme un masque antipoussières, des chaussures de sécurité

antidérapantes, un casque de protection et des protecteurs auditifs, lorsque les conditions

l’exigent, réduit les risques de blessures.

Évitez tout démarrage involontaire. Assurez-vous que l’interrupteur est sur la position

d’arrêt avant de brancher l’outil sur une source d’alimentation ou un bloc-piles, de

ramasser l’outil ou de le transporter. Transporter les outils électriques avec le doigt sur la

gâchette ou brancher les outils lorsque l’interrupteur est à la position de marche augmente les

risques d’accident.

Enlevez toute clé de serrage ou clé à molette avant de mettre l’outil électrique

en marche. Une clé de réglage oubliée sur une pièce rotative de l’outil électrique peut

occasionner des blessures graves.

Ne vous étirez pas pour étendre votre portée. Gardez une posture sécuritaire et un bon

équilibre en tout temps. Cela vous permet de mieux maîtriser l’outil électrique lorsque des

situations inattendues se présentent.

Habillez-vous de manière appropriée. Ne portez pas de vêtements amples ni de bijoux.

Gardez vos cheveux et vos vêtements loin des pièces mobiles. Les vêtements amples, les

bijoux et les cheveux longs risquent de se prendre dans les pièces en mouvement.

Si un dispositif permet de raccorder un dépoussiéreur, assurez-vous que celui-ci est

branché et utilisé de manière appropriée. L’emploi d’un dépoussiéreur contribue à réduire

les dangers liés à la poussière.

Même si vous connaissez parfaitement ces outils parce que vous les utilisez souvent,

soyez vigilant et respectez les principes de sécurité. Il suft d’être négligent une fraction

de seconde pour se blesser gravement.

Utilisation et entretien d’un outil électrique

Ne forcez pas l’outil électrique. Utilisez l’outil électrique approprié à la tâche que vous

souhaitez accomplir. L’outil électrique adéquat vous permettra de mieux accomplir le travail

avec plus de sécurité et au rythme pour lequel il a été conçu.

N’utilisez pas l’outil électrique si l’interrupteur ne permet pas de le mettre en marche et

de l’arrêter. Tout outil qui ne peut pas être contrôlé par l’interrupteur est dangereux et doit

être réparé.

Débranchez la che de la prise ou retirez, si possible, le bloc-piles de l’outil électrique

avant d’effectuer des réglages, de changer d’accessoire ou de le ranger. De telles

mesures de sécurité préventives réduisent les risques de mise en marche accidentelle de l’outil

électrique.

Rangez l’outil électrique à l’arrêt hors de la portée des enfants et n’autorisez pas une

personne ne sachant pas s’en servir ou n’ayant pas lu ces instructions à l’utiliser. Les

outils électriques sont dangereux s’ils se retrouvent entre les mains d’utilisateurs qui ne

savent pas s’en servir.

Entretenez les outils électriques et les accessoires. Vériez les pièces mobiles pour

vous assurer qu’elles ne sont pas désalignées, enrayées, brisées, ou dans un état qui

pourrait nuire à leur fonctionnement. Si l’outil électrique est endommagé, faites-le

réparer avant de l’utiliser. De nombreux accidents sont provoqués par des outils électriques

mal entretenus.

Maintenez les outils de découpe affûtés et propres. Des outils tranchants bien entretenus

et dont les lames sont affûtées risquent moins de se bloquer et sont plus faciles à maîtriser.

Utilisez l’outil électrique, les accessoires, les embouts et les autres éléments

conformément aux présentes instructions, en tenant compte des conditions de travail

et du travail à effectuer. L’utilisation de l’outil électrique à des ns autres que celles pour

lesquelles il a été conçu pourrait entraîner une situation dangereuse.

Les poignées et autres surfaces de préhension doivent toujours être sèches, propres et

exemptes d’huile ou de graisse. Les poignées et autres surfaces de préhension glissantes

ne permettent pas de manipuler ni de contrôler l’outil de façon sécuritaire en cas de situations

inattendues.

La page charge ...

Skil SR6604B-10 Le manuel du propriétaire

Marque: Skil

Modèle: SR6604B-10

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Skil SR6604B-10 Owner's manual
español: Skil SR6604B-10 El manual del propietario

Documents connexes

Autres documents

Bosch Power Tools 1293d Manuel utilisateur