Miller ARCCOOL V3 Le manuel du propriétaire

Marque: Miller

Modèle: ARCCOOL V3

Taper: Le manuel du propriétaire

Ce manuel convient également à

KK305153

OWNER’S MANUAL

OMĆ617 193 396B

February 2000

ARCCOOL V3

1. Specifications

Recirculating Coolant System For Water-Cooled GTAW Torches And GMAW Guns

Use With Guns/Torches Rated Up To 600 Amperes

IP Rating: 23

3 gal (11.4 L) Coolant Tank Capacity;

Maximum Cooling Capacity: 14,000 BTU/hr At 1.3 qt/min (1.25 L/min)

Dimensions: 12-1/4 in (311 mm) Deep, 9-3/4 in (248 mm) Wide, 33 in (838 mm) High

Weight: 50 lb (23 kg)

Ref. ST-802 367

Single-Phase Input Power, 115 Volts AC, 4.7 A 60 Hz, 5.9 A, 50 Hz

2. Safety Symbol Definitions

Means Warning! Watch Out! There are possible hazards

with this procedure! The possible hazards are shown in

the adjoining symbols.

Symbole graphique d’avertissement! Attention! Cette pro-

cédure comporte des risques possibles! Les dangers

éventuels sont représentés par les symboles graphiques

joints.

Have only trained and qualified persons install, operate,

or service this unit. Call your distributor if you do not un-

derstand the directions. For WELDING SAFETY and

EMF information, read wire feeder and welding power

source manuals.

L’installation, l’exploitation et l’entretien de cet appareil

doivent être confiés uniquement à des personnes

qualifiées et convenablement formées. S’adresser à un

distributeur si l’on ne comprend pas les directives. Pour

des renseignements ayant trait à la SÉCURITÉ lors du

soudage et aux champs électromagnétiques, consulter

les manuels traitant les dévidoirs et les sources de

courant pour le soudage.

Beware of electric shock from wiring.

Attention! Risque d’électrocution due au contact avec des

fils.

Beware of moving parts.

Attention! Pièces en mouvement.

Wear safety glasses with side shields.

Porter des lunettes de sécurité avec protections

latérales.

Recycle or dispose of used coolant in an environmentally

safe way.

Recycler ou éliminer tout liquide de refroidissement usé

conformément aux méthodes prescrites pour assurer la

protection de l’environnement.

OM-617 Page 2

3. Rating Label

S/N: KJ

043009-011

115

5.5

ARCCOOL V3

Hz50/60

IP 23

A I

MILLER ELECTRIC MFG. CO., APPLETON, WI USA

NRTL/C

LR5071

4. Symbols And Definitions

Some symbols are found only on CE products.

NOTE

Amperes Alternating Current Voltage Input

Circulating Unit

With Coolant Pump

Volts

Water (Coolant) In-

put

Water (Coolant)

Output

Line Connection

Protective Earth

(Ground)

Degree Of

Protection

Primary Current

Hertz

On Off

Primary Voltage Single Phase

5. Tipping

Y Be careful when placing or

moving unit over uneven

surfaces.

Ref ST-802 055

OM-617 Page 3

6. Preparing Cooling Unit For Use

Ref. ST-802 367

Fittings have 5/8-18 left-hand

threads. Connect hoses with

proper fittings as shown.

1 Flow Indicator

2 Filler Cover

Use table to select proper coolant,

and fill tank. Keep coolant level full.

3 Power Switch

4 Coolant Out Fitting

5 Coolant In Fitting

Tools Needed:

11/16 in

Low Conductivity Coolant No.

043 810**;

Distilled Or Deionized Water

OK Above 32° F (0° C)

Low Conductivity Coolant No.

043 810**; Or

Aluminum Protecting Coolant

No. 043 809**;

Distilled Or Deionized Water

OK Above 32° F (0° C)

GTAW Or Where

HF* Is Used

GMAW Or Where

HF* Is Not Used

Application

*HF: High-Frequency Current

**These coolants protect to -37° F (-38°C) and resist algae growth.

Coolant

Aluminum Protecting

Coolant No. 043

809**

Where Coolant Contacts

Aluminum Parts

Y Use of any coolant other than those listed in the table voids the warranty on any parts

that come in contact with the coolant (pump, radiator, etc.).

OM-617 Page 4

7. Connections

ST-802 368

To prevent overheating, make sure

cooling unit is positioned so airflow

is not restricted.

Y When using coolant system

with a welding power source

with a water valve, bypass

water valve on welding pow-

er source by connecting di-

rectly to torch/gun to avoid

overheating, or damage to

coolant system.

Y To prevent tipping when

placing unit on uneven or tilt-

ing surfaces, properly se-

cure the coolant system to a

wall, stationary support, or

equivalent rigid structure.

GTAW Connections

GMAW Connections

OM-617 Page 5

Turn Off and unplug unit.

1 Motor

Remove plugs and put about 15

drops of SAE 20 motor oil into each

oil port. Replace plugs, and reas-

semble unit.

2 Coolant Pump

3 Filter Cap

Place cloth or suitable container un-

der nut, and remove nut.

4 Strainer

Rinse strainer with clean water.

Reinstall parts. Remove cloth or

container, and reinstall wrapper.

. Relief valve is factory set at 60

psi (414 kPa), and normally

needs no adjustment: Only ad-

just if replacing motor.

5 Pressure Gauge

6 Relief Valve Adjustment

Screw

Connect gauge to Coolant Out fit-

ting as shown. Block or plug any

output fitting on gauge.

Turn On power, and adjust pres-

sure adjustment screw as needed.

Turn Off power. Disconnect gauge

and reinstall nut and wrapper.

. If replacing hoses, use hoses

compatible with ethylene gly-

col, such as Buna-n, Neo-

prene, or Hypalon. NOTE:

Oxy-acetylene hoses are not

compatible with any product

containing ethylene glycol.

3/8 in

Tools Needed:

8. Coolant Maintenance And Oiling Motor

ST-802 369

15/16, 3/4 in

Decrease Increase

OM-617 Page 6

9. Routine Maintenance

Y Turn Off all power and unplug unit before maintaining.

1 Month

Blow Out Heat

Exchanger Fins

Y Clean coolant strainer. Severe conditions

may require more frequent cleaning (continu-

ous use, high/low temperatures, dirty envi-

ronment, etc.). Failure to properly clean

coolant strainer voids pump warranty.

6 Months

Replace

Cracked

Hoses

Replace

Unreadable

Labels

Change

Coolant (If

Using Water)

12 Months

Oil Motor

Change

Coolant (If

Using CO809

Or CO810

Coolants)

10. Troubleshooting

Trouble Remedy

Coolant system does not work. Be sure input power cord is plugged in to energized receptacle.

Check line fuses or circuit breaker, and replace or reset if necessary.

Motor overheated. Unit starts running when motor has cooled.

Have Factory Authorized Service Agent check Power switch and motor.

Decreased or no coolant flow. Add coolant.

Check for clogged hoses or coolant filter.

Disconnect pump, and check for sheared coupling. Replace coupling if necessary.

SA-135 796-D

BLK

WHT

GRN/YEL

MOT

PLG1

INPUT POWER

Figure 10-1. Circuit Diagram

OM-617 Page 7

11. Parts List

ST-802 364-B

. Hardware is common and

not available unless listed.

Figure 11-1. Complete Assembly

OM-617 Page 8

Description

Part

No.

Dia.

Mkgs.

043 009

Item

No.

Figure 11-1. Complete Assembly

Quantity

1 166 608 CAP, tank screw-on w/vent 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 194 179 TUBE, pick-up coolant 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 192 852 TANK, reservoir 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4A,4B 194 174 TUBING, PVC .375 ID x .625 OD x 15.000 clear brd 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5A,5B 174 044 TUBING, PVC .375 ID x .625 OD x 18.000 clear brd 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 196 515 RADIATOR, heat exchanger 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 197 361 PUMP, coolant (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 126 978 FITTING, hose brs barbed M 3/8tbg x 3/8NPT 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 196 990 FITTING, hose brs barbed 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 134 795 COUPLER, drive pump 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 194 173 HOSE, NPRN brd No. 1 x .375 ID x 21.000 black 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 MOT 173 263 MOTOR, 1/4hp 115VAC 50/60Hz 1425/1725RPM 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 166 570 BLADE, fan 9.000 5wg 38deg .500 bore CW AL 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 192 848 BRACKET, mtg motor/pump 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 192 856 PLENUM, fan 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16 192 858 COVER, top 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 PLG1 192 457 CABLE, power 11ft 5 in 16ga 3/c 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 139 042 BUSHING, strain relief .270/.470 ID x .804mtg hole 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 192 854 CASE SECTION, wrapper 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 192 857 CASE SECTION, main 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 192 449 LABEL, warning/caution 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22 166 564 FILTER, in-line low profile 100 screen 3/8 hose bar 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 168 254 CLIP, filter mounting 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 186 003 INDICATOR, flow 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25 166 560 RING, rtng ext .500 shaft x .042thk E style bowed 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 166 571 FITTING, coolant barbed 3/8tbg 5/8-18 female 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27 166 568 PADDLE, flow indicator 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28 166 566 O-RING, 1.301 ID x .070 CS 70 Duro Buna–N1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29 186 005 LENS, flow indicator 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 193 710 NAMEPLATE, (order by model and serial number) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31 S1 177 396 SWITCH, rocker DPST 15A 250VAC 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32 +192 859 PANEL, front 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33 177 448 WEATHERSTRIPPING, adh .250 x .375 x 8.500 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+When ordering a component originally displaying a precautionary label, the label should also be ordered.

BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.