GE AEE08 Le manuel du propriétaire

Safety Instructions ........................ 2, 3

Operating Instructions

................. 4, 5

Care and Cleaning

Air Filter ............................................................. 5

Grille and Case ............................................... 5

Outdoor Coils .................................................. 5

Installation Instructions

Through-the-Wall

Installation—Optional ...............................12

Window Installation .............................7–11

Troubleshooting Tips ..............14, 15

Consumer Support

Consumer Support ..................Back Cover

Ownership Registration for

Customers in Canada only ............15, 16

Warranty for Customers

in Canada .......................................................17

Warranty for Customers

in the U.S.A. ....................................................18

49-7625 12-09 GE

AEE08

AEE12

Owner’s Manual and

Installation Instructions

Write the model and serial numbers here:

Model # _________________________

Serial # __________________________

Find these numbers on a label on the side of

the air conditioner.

Air Conditioners

GEAppliances.com

Room

Climatiseur

Acondicionador

de aire

Manuel d’utilisation et

instructions d’installation

Manual del propietario

y instrucciones de

instalación

La section française commence à la page 19

La sección en español empieza en la página 35

In Canada, contact us at:

www.GEAppliances.ca

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

n Use this appliance only for its intended

purpose as described in this Owner’s

Manual.

n This air conditioner must be properly

installed in accordance with the Installation

Instructions before it is used.

n Never unplug your air conditioner by pulling

on the power cord. Always grip plug firmly

and pull straight out from the receptacle.

n Replace immediately all electric service

cords that have become frayed or otherwise

damaged. A damaged power supply cord

must be replaced with a new power supply

cord obtained from the manufacturer and

not repaired. Do not use a cord that shows

cracks or abrasion damage along its length

or at either the plug or connector end.

n If the receptacle does not match the plug,

the receptacle must be changed out by a

qualified electrician.

n Turn the unit OFF and unplug your air

conditioner before making any repairs

or cleaning.

NOTE: We strongly recommend that any

servicing be performed by a qualified

individual.

n For your safety…do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

n All air conditioners contain refrigerants,

which under federal law must be removed

prior to product disposal. If you are getting

rid of an old product with refrigerants, check

with the company handling disposal about

what to do.

n These R410A air conditioning systems

require contractors and technicians to use

tools, equipment and safety standards

approved for use with this refrigerant.

DO NOT use equipment certified for R22

refrigerant only.

SAFETY PRECAUTIONS

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord. For

personal safety, this appliance must be properly

grounded.

DO NOT use an adapter plug with this

appliance.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric

shock hazard from this appliance.

Power cord includes a current interrupter device.

A test and reset button is provided on the plug

case. The device should be tested on a periodic

basis by first pressing the TEST button and then

the RESET button. If the TEST button does not

trip or if the RESET button will not stay engaged,

discontinue use of the air conditioner and

contact a qualified service technician.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be

plugged into its own individual electrical

outlet which has a voltage rating that matches

the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

See the Installation Instructions, Electrical

Requirements section for specific electrical

connection requirements.

HOW TO CONNECT ELECTRICITY

3

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

WARNING!

Because of potential safety hazards under certain

conditions, we strongly recommend against the use

of an extension cord.

However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed,

14 gauge, 3-wire grounding type appliance

extension cord having a grounding type plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 volts.

CAUTION:

DO NOT use an extension cord with any of the

230/208 volt models.

EXTENSION CORDS—115-Volt models only

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

GEAppliances.com

4

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

About the controls on the air conditioner.

Features and appearance will vary.

TEMP CONTROL MODE CONTROL

Temp Control

The temp control is used to maintain

the room temperature. The compressor

will cycle on and off to keep the room at

the same level of comfort. Turn the knob

clockwise to Cooler (blue) and the indoor

air will become cooler. Turn the knob

counterclockwise to Warmer (red) and

the indoor air will become warmer.

Mode Control

Hi Cool and Low Cool provide cooling with

different fan speeds.

Hi Heat and Low Heat provide heating with

different fan speeds.

Fan Only setting provides air circulation

and filtering without cooling or heating.

NOTE: If you move the mode control

from a cool setting to Off, a fan setting

or a heat setting, wait at least 3 minutes

before switching back to a cool setting.

Cooling Descriptions

For Normal Cooling—Select Hi Cool

or Low Cool with the temp control at

midpoint.

For Maximum Cooling—Select Hi Cool with

the temp control turned clockwise as far as

possible.

For Quieter and Nighttime Cooling—Select

Low Cool with the temp control at midpoint.

Heating Descriptions

For Normal Heating—Select Hi Heat

or Low Heat with the temp control at

midpoint.

For Maximum Heating—Select Hi Heat with

the temp control turned counterclockwise

as far as possible.

For Quieter & Nighttime Heating—Select

Low Heat with the temp control at

midpoint.

Controls

Normal Operating Sounds

n You may hear a pinging noise caused by

water being picked up and thrown against the

condenser on rainy days or when the humidity

is high. This design feature helps remove

moisture and improve efficiency.

n You may hear the thermostat click when the

compressor cycles on and off.

n Water will collect in the base pan during

high humidity or on rainy days. The water

may overflow and drip from the outdoor side

of the unit.

n The fan may run even when the compressor

does not.

5

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

Air Direction

Use the lever to adjust the air direction left and right

only.

Fingertip pressure on the horizontal louvers

adjusts the air direction up or down.

GEAppliances.com

Additional important information.

Air Filter

The air filter behind the front grille should be checked

and cleaned at least every 30 days or

more often if necessary.

To remove:

Push on one side of the filter edge and pull it out the

other side.

Clean the filter with warm, soapy water. Rinse and let

the filter dry before replacing it. Do not clean the filter

in a dishwasher.

CAUTION: DO NOT operate the air

conditioner without a filter because dirt and lint

will clog it and reduce performance.

Outdoor Coils

The coils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged with

dirt or soot, they may be professionally cleaned.

Turn the air conditioner off and remove the plug from

the wall outlet before cleaning.

To clean, use water and a mild detergent.

Do not use bleach or abrasives.

Grille and Case

Care and cleaning of the air conditioner.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance

requires basic mechanical skills.

• Completion time –

Approximately 1 hour

• Werecommendthattwopeopleinstall

this product.

• Properinstallationistheresponsibility

of the installer.

• Productfailureduetoimproperinstallation

isnotcoveredundertheWarranty.

• You MUST use all supplied parts and use proper

installation procedures as described in these

instructions, and any separate kit instructions,

when installing this air conditioner.

Installation

Air Conditioner

Instructions

Some models require a 115/120-volt a.c.,

60 Hz grounded outlet protected with

a 15-amp time delay fuse or circuit

breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall

outlet you plan to use is only a 2-prong outlet,

it is your responsibility to have it replaced with

a properly grounded 3-prong wall outlet.

Some models require 230/208-volt a.c.,

protected with a time delay fuse or circuit

breaker. These models should be installed

on their own single branch circuit

for best performance and to prevent

overloading house or apartment wiring

circuits, which could cause a possible fire

hazard from overheating wires.

ELECTRICAL REQUIREMENTS

CAUTION:

Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present special

problems—consult a qualified electrician.

If the sill support bolts do not contact the

window sill, or if you have a window without

a sill, you must order accessory kit RAK87

to properly install this air conditioner. Call

800.626.2002 or visit GEAppliances.com.

TOOLS YOU WILL NEED

Phillips-headscrewdriver

Adjustable wrench

Ruler or tape measurePencil

Level

Scissors or knife

Flat-blade screwdriver

Powercordincludesacurrentinterrupter

device. A test and reset button is provided on

the plug case. The device should be tested on a

periodic basis by first pressing the TEST button

and then the RESET button. If the TEST button

does not trip or if the RESET button will not stay

engaged, discontinue use of the air conditioner

and contact a qualified service technician.

6

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

7

Type A (6)

Type B (7)

Right

accordion

panel

Foam top

window gasket

Windowlocking

bracket (2)

Left

accordion

panel

Top mounting rail

Window Installation Instructions

PARTS INCLUDED

(appearance may vary)

Type C (6)

Type D (3)

Case bottom seal

(thin, adhesive-backed)

Sill support (2)

Nut (2)

Bolt (2)

Window Installation Instructions

WINDOW REQUIREMENTS

•These instructions are for a standard

double-hung window. You will need to

modify them for other types of windows.

CAUTION:

If the sill support

bolts do not contact the window sill or

if you have a window without a sill, you

must order accessory kit RAK87 to

properly install this air conditioner.

Call 800.626.2002 or visit GEAppliances.

com.

•All supporting parts must be secured

to firm wood, masonry or metal.

•The electrical outlet must be within

reach of the power cord.

1

17” min.

27″ to 36″

(Withaccordionpanels)

REMOVE THE AIR CONDITIONER

FROM THE CASE

Remove and save the 2 screws from the

lower sides of the front grille.

Remove the two control knobs.

Grasp the lower corners of

the grille while pressing in on the case

sides with your fingertips.Pulloutto

release and lift it up.

NOTE: Do not pull the bottom edge

toward you more than 3″ or you may

damage the tabs of the grille.

Remove the ground screw from each side

of the case. Keep them in a safe location.

NOTE: Be sure to save these screws. You will

need them later in the installation.

3

A

B

FRONT

STORM WINDOW REQUIREMENTS

A storm window frame will not allow the

air conditioner to tilt toward the outside,

and will keep it from draining properly.

To adjust for this, attach a piece of wood

to the stool.

WOOD PIECES–

WIDTH: 2″

LENGTH: Long enough to fit inside the

window frame.

THICKNESS: To determine the thickness,

place a piece of wood on the stool to

make it 1/2″ higher than the top of the

storm window frame or the vinyl frame.

Attach securely with nails or screws

provided by the installer.

2

1/2″ higher

than storm

window

frame

Storm window

frame

Wood

Stool

1/2″ higher

than vinyl frame

(on some windows)

Vinyl frame

8

C

FRONT

D

FRONT

INSTALL THE BOTTOM

CASE SEAL

•Peelthebackingfromthebottom

case seal and attach it along the

bottom of the case in front of the bottom

mounting rail.

Window Installation Instructions

INSTALL THE TOP

MOUNTING RAIL ONTO THE CASE

Attach the top mounting rail onto the top

of the case with 3 Type B screws.

Pressfirmlytodrivethescrewsintothe

gasket and through the top mounting rail.

5

Type B

screws

Top

mounting

rail

INSTALL THE

SIDE ACCORDION PANELS

Slide the left and right accordion panels

into the top and bottom mounting rails.

Attach the accordion panels to the case

using 3 Type A screws on each side.

6

A

B

Type A

screws

Top mounting rail

Bottom mounting rail

Accordion

panel

4

Bottom case seal

BACK

REMOVE THE AIR CONDITIONER

FROM THE CASE (CONT.)

Slide the air conditioner from the case by

gripping the base pan handle and pulling

forward while bracing the case. Do not

pull or lift on the styrofoam discharge area.

3

E

FRONT

Do not

pull

or lift

in this

area—

damage

to the

unit may

result

Bottom

mounting rail

9

Window Installation Instructions

INSTALL THE CASE IN THE

WINDOW

Open the window and mark the centerline of

the window stool.

Carefully place the case on the window stool

and align the center mark on the bottom front

with the centerline of the stool.

Pullthewindowdownbehindthetop

mounting rail.

NOTE: Do not shut the window so tightly that

movement of the accordion panels is

restricted.

Select the position that will place the sill

supports near the outermost point on the sill.

Placetheshortsideofthesillsupports,onthe

case bottom, toward the window. Attach the

sill supports to the case track hole in relation

to the selected position using 2 Type B screws

in each support.

CAUTION: Do not install this air

conditioner in a window if the bolts do not

contact the window sill.

Adjust the bolt and the nut in each support so

that the case is installed with

a slight tilt to the outside. Use a level; no more

than 1/2 bubble will be the correct case slant

to the outside.

CAUTION: If the sill support bolts

do not contact the window sill or if you have a

window without a sill you must order accessory

kit RAK87 to properly install this air conditioner.

Call 800.626.2002 or visit GEAppliances.com.

7

INSTALL THE CASE IN THE

WINDOW (CONT.)

Secure the case to

the window stool

by using

3 Type D screws.

Pulltheaccordion

panels to each

window sash track.

Attach them on each

side to the window

sash and the window

stool using

4 Type C screws.

7

A

B

C

F

D

Long side

of sill

supports

OUTSIDE

E

G

Sill

support

10

8

SECURE THE CASE IN THE WINDOW

AND INSTALL THE FOAM TOP

WINDOW GASKET

A

CAUTION:

To prevent broken glass

or damage to windows,

on vinyl or other similarly

constructed windows,

attach the support bracket

to the window side jam.

B

C

Wood

Vinyl

Attach the window

locking brackets (on one

each side) with Type C

screws.

Cut the foam top window gasket to the window

width.

Stuff the foam

between the glass

and the window

to prevent air and

insects from getting

into the room.

NOTE: If the gasket supplied does not fit your

window, obtain appropriate material locally to

provide a proper installation seal.

Window Installation Instructions

INSTALL THE AIR CONDITIONER

IN THE CASE (CONT.)

Attach the front grille to the case by inserting

the tabs on the grille into the slots on the

fronttopofthecase.Pushthegrillein.

Secure the front grille to the case by

replacing the 2 screws removed earlier.

Pressonthetopofthegrilletohelpwith

side screw installation.

Replace the two control knobs.

Connect power.

9

INSTALL THE AIR CONDITIONER

IN THE CASE

Slide the air conditioner into the case by

the base pan. Do not push on the controls,

styrofoam air discharge housing or the finned

coils. Make sure the air conditioner is firmly

seated.

Replace the 2 screws removed earlier, one

on each side of the case.

IMPORTANT: THE GROUND SCREWS MUST BE

REINSTALLED TO ENSURE PROPER GOUND.

9

A

F

11

Do not press on

these areas—

damage to the

unit may result

BasePan

B

E

D

C

Through-the-Wall Installation Instructions—Optional

The case may be installed through-the-wall

in both existing and new construction.

Read completely, then follow step-by-step.

NOTE: Obtain all materials locally for

mounting the air conditioner through-

the-wall.

IMPORTANT

Through-the-wall installation is not

appropriate if any of the side or top louvers

in the case will be obstructed by the wall.

All side and top louvers in the case must

project on the outdoor side of the wall.

The room side of the case must project

into the room far enough to maximize the

balance of the unit.

The case must be installed level from side-

to-side and with a slight tilt from front to

rear. Use a level; no more than a 1/2 bubble

will be the correct case slant to the outside.

Lintel angle is required to support bricks or

blocks above opening.

Flashing is required and should extend the

length of the opening to ensure no inside

cavity leakage occurs.

Remove the air conditioner from the case.

Forspecificinstruction,refertotheWindow

Installation Instructions.

Make certain that a wall receptacle is

available close to the hole location or make

arrangements to install a receptacle.

Placethecaseinthewallopeningand

place wood support strips between the case

bottom and the flashing on both sides of the

bottom rail. They should be the same height

as the bottom rail and the same length as

the wall opening.

1

A

B

12

FINISH THE WALL OPENING

Caulk all four sides on the outdoor side of

the case to prevent moisture from getting

through to the interior wall. Use of flashing

(drip rail) will further prevent water from

dripping inside the wall and down the

outside of the building.

Place the air conditioner into the case.

For specific instruction, refer to the Window

Installation Instructions.

2

IMPORTANT (cont.)

Secure with 14 wood screws anchored at

least an inch into the wall support structure.

NOTE: Drill pilot holes, if necessary, for

proper installation. If the frame is oversized,

use shims to prevent case distortion.

1

D

A

B

Lintel angle

Plasterline

Trim molding

(if desired)

INSIDE

Bottom rail

Woodfillerand

caulking (above

and below the

flashing)

Air louvers

(top and

sides must

project on the

outdoor side

of the wall)

OUTSIDE

Flashing

(Drip rail)

Case

bottom

Bottom

rail

Flashing

(Drip rail)

Woodsupportstrips

Caulking

C

13

Before you call for service… GEAppliances.com

Problem Possible Causes What To Do

Air conditioner The air conditioner •Make sure the air conditioner plug is pushed completely

does not start is unplugged into the outlet.

The fuse is blown/circuit • Check the house fuse/circuit breaker box and replace

breaker is tripped the fuse or reset the breaker.

Power failure • The unit will automatically re-start in the settings last

used after the power is restored.

• There is a protective time delay (approximately

3 minutes) to prevent tripping of the compressor

overload. For this reason, the unit may not start

normal cooling or heating for 3 minutes after it

is turned back on.

The current interrupter • Press the RESET button located on the power cord plug.

device is tripped

• If the RESET button will not stay engaged, discontinue

use of the air conditioner and contact a qualified service

technician.

Air conditioner Ice blocks the air flow • Set the mode control at Fan Only or Hi Cool with the

freezing up and stops the air conditioner temp control at a warmer setting.

from cooling the room

Air conditioner does not Airflow is restricted • Make sure there are no curtains, blinds or furniture

cool as it should blocking the front of the air conditioner.

The temp control may • Turn the temperature knob clockwise as far as possible.

not be set correctly

The air filter is dirty • Clean the filter at least every 30 days. See the Operating

Instructions section.

The room may have been hot • When the air conditioner is first turned on you need

to allow time for the room to cool down.

Cold air is escaping • Check for open furnace floor registers and

cold air returns.

• Set the air conditioner’s vent to the closed position.

Cooling coils have iced up • See “Air conditioner freezing up” above.

Air conditioner does not Airflow is restricted • Make sure there are no curtains, blinds or furniture

warm as it should blocking the front of the air conditioner.

The temp control may • Turn the knob counterclockwise as far as possible.

not be set low enough The lowest setting provides maximum warming.

The air filter is dirty • Clean the filter at least every 30 days. See the Operating

Instructions section.

The room may have been cold • When the air conditioner is first turned on, you need to

allow time for the room to warm up.

Warm air is escaping • Check for open furnace floor registers and

cold air returns.

Troubleshooting Tips

Save time and money! Review the chart below first

and you may not need to call for service.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions

Installation

Instructions

14

Problem Possible Causes What To Do

Water drips outside Excessively hot and • This is normal.

humid weather

Water drips indoors The air conditioner is not • For proper water disposal, make sure the air conditioner

tilted to the outside slants slightly from the case front to the rear.

Water collects in Moisture is removed from • This is normal for a short period in areas with

base pan indoor air and drains into little humidity; normal for a longer period in very

rear of a cabinet where a fan humid areas.

blows it against the outdoor

condenser coil

Troubleshooting Tips

Before you call for service…

15

OWNERSHIP REGISTRATION

P.O. BOX 1780

MISSISSAUGA, ONTARIO

L4Y 4G1

(FOR CANADIAN CONSUMERS ONLY)

Please place in envelope and mail to:

Veuillez mettre dans une enveloppe et envoyez à :

16

17

Consumer Support

Troubleshooting

Tips

Installation

Instructions

Care and Cleaning

Operating

Instructions

Safety Instructions

Staple your receipt here.

Proof of the original purchase

date is needed to obtain

service under the warranty.

GEAirConditioner—One-YearLimitedWarranty. (For customers in the U.S.A.)

For The Period Of: GE Will Replace:

One Year Any part of the air conditioner which fails due to a defect in materials or workmanship.

From the date of the During this limited one-year warranty, GE will also provide, free of charge, all labor and related

original purchase service to replace the defective part.

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

Æ

technician. To schedule service,

visit us on-line at GEAppliances.com, or call 800.GE.CARES

(800.432.2737). Have serial number and model number available

when calling for service.

n Service trips to your home to teach you how to

use the product.

n Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

n Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

n In commercial locations, labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

n Replacement of house fuses or resetting of circuit

breakers.

n Failureduetocorrosiononmodelsnotcorrosion-

protected.

n Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

n Incidental or consequential damage caused by possible

defects with this air conditioner.

n Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not

available, you may be responsible for a trip charge or you may be required to bring the product to an

Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping or service

calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

EXCLUSIONOFIMPLIEDWARRANTIES—Yoursoleandexclusiveremedyisproductrepairasprovidedin

this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or

fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

18

Staple your receipt here.

Proof of the original purchase

date is needed to obtain

service under the warranty.

GEAirConditioner—One-YearLimitedWarranty. (For customers in the Canada)

For The Period Of: Mabe Will Replace:

One Year Any part of the air conditioner which fails due to a defect in materials or workmanship.

From the date of the During this limited one-year warranty, Mabe will also provide, free of charge, all labor and

original purchase related service to replace the defective part.

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

Æ

technician. For service, call

1.800.561.3344. Please have serial number and model number

available when calling for service.

n Service trips to your home to teach you how to

use the product.

n Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

n Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

n In commercial locations, labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

n Replacement of house fuses or resetting of circuit

breakers.

n Failureduetocorrosiononmodelsnotcorrosion-

protected.

n Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

n Incidental or consequential damage caused by possible

defects with this air conditioner.

n Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased in

Canada for home use within Canada. In-home warranty service will be provided in areas where it is available

and deemed reasonable by Mabe to provide.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above

exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other

rights which vary from province to province. To know what your legal rights are in your province, consult your

local or provincial consumer affairs office.

Warrantor: Mabe Canada Inc.,

Burlington, Ontario

EXCLUSIONOFIMPLIEDWARRANTIES—Yoursoleandexclusiveremedyisproductrepairasprovidedin

this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or

fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

Safety Instructions

Operating

Instructions

Care and Cleaning

Installation

Instructions

Troubleshooting

Tips

Consumer Support

Consignes de sécurité .............20, 21

Consignes d’utilisation

...............22, 23

Entretien et nettoyage

Filtre à air ................................ 23

Retrait du cadre de la grille ............... 23

Serpentins extérieurs ..................... 23

Instructions de montage

Instructions de montage pour une

installation à travers un mur—En option ...... 30

Instructions de montage

dans une fenêtre ..................... 25–29

Conseils de dépannage ............... 33

Service à la clientèle

Service à la clientèle ....................... 36

Garantie .................................. 35

Enregistrement du titre

de propriété ...........................31, 32

Inscrivez ici les numéros de modèle et de série :

Numéro de modèle : _______________________

Numéro de Série : _______________________

Vous trouverez ces numéros sur l’étiquette

apposée sur le côté du climatiseur.

19

Au Canada, visitez-nous au :

www.electromenagersge.ca

Assistance à

la clientèle

Conseils de

dépannage

Instructions

de montage

Entretien et

nettoyage

Consignes

d’utilisation

Consignes

de sécurité

AEE08

AEE12

IMPORTANTES CONSIGNES DE SÉCURITÉ.

VEUILLEZ LIRE TOUTES LES CONSIGNES AVANT UTILISATION.

AVERTISSEMENT !

Pour votre sécurité, les informations contenues dans ce manuel doivent être suivies afin de minimiser

les risques d’incendie, de chocs électriques ou de blessures corporelles.

n N’utilisez cet appareil qu’aux fins prévues

décrites dans le manuel d’utilisation.

n Ce climatiseur doit être correctement

installé conformément aux Instructions

d’Installation avant toute utilisation.

n Ne débranchez jamais votre climatiseur en

tirant sur le cordon d’alimentation. Prenez

toujours fermement la fiche en main et tirez

pour la sortir de la prise.

n Remplacez immédiatement tout cordon

électrique usé ou endommagé. Un

cordon d’alimentation endommagé doit

être remplacé par un nouveau cordon

d’alimentation obtenu du fabricant. Ne

réparez pas le cordon endommagé. N’utilisez

pas un cordon fissuré ou présentant des

dommages dus aux frottements soit sur

sa longueur ou aux extrémités du côté

de la fiche ou du raccord.

n Si la prise de courant est d’un format

différent de la fiche, cette prise doit être

changée par un électricien qualifié.

n Eteignez votre climatiseur et débranchez-le

avant d’effectuer des réparations ou de

le nettoyer.

REMARQUE : Nous vous recommandons de faire

effectuer la maintenance par un technicien qualifié.

n Pour votre sécurité, ne stockez pas et

n’utilisez pas de matériaux combustibles,

d’essence ou d’autres vapeurs et liquides

inflammables dans les parages de cet

appareil ou de tout autre appareil.

n Tous les climatiseurs contiennent des

fluides frigorigènes qui, conformément, à la

législation fédérale doivent être retirés avant

la mise au rebut de l’appareil. Si vous mettez

au rebus un ancien appareil contenant des

fluides frigorigènes, vérifiez la procédure à

suivre auprès de la compagnie responsable

de l’élimination.

n Ces systèmes de climatisation R410A

demandent que les contracteurs et

les techniciens utilisent des outils, de

l’équipement et des mesures de sécurité

homologués pour une utilisation avec

frigorigène. N’UTILISEZ PAS un équipement

certifié pour fluide R22 refrigerant only.

CONSIGNES DE SÉCURITÉ

Ne coupez pas ou n’enlevez pas, sous aucun

prétexte, la troisième broche de mise à la terre

du cordon d’alimentation. Pour des raisons

de sécurité, cet appareil doit être correctement

mis à la terre.

N’utilisez PAS d’adaptateur avec cet appareil.

Le cordon d’alimentation de cet appareil

est équipé d’une fiche à trois broches (pour une

mise à la terre) qui s’adapte à la prise

de courant standard à 3 broches (pour une mise

à la terre) pour minimiser les risques

de chocs électriques par cet appareil.

Le cordon d’alimentation est équipé d’un

dispositif d’interruption du courant. Un bouton

d’essai et de réenclenchement est fourni

sur le boîtier de la prise. Vous devez tester le

mécanisme régulièrement en appuyant d’abord

sur le bouton TEST (Essai) puis sur le bouton

RESET (Réenclenchement) lorsque l’appareil est

branché. Si le bouton TEST (Essai) ne bascule pas

ou si le bouton RESET (Réenclenchement) ne reste

pas enclenché, cessez d’utiliser votre climatiseur

et appelez un technicien de service qualifié.

Faites vérifier la prise murale et le circuit

électrique par un électricien qualifié pour

s’assurer que le système est correctement

mis à la terre.

Dans le cas d’une prise biphasée,

l’installateur a la responsabilité et l’obligation

de la remplacer par une prise triphasée

correctement mise à la terre.

Le climatiseur doit toujours être branché

à sa propre prise électrique d’une tension

nominale correspondant à celle indiquée

sur sa plaque signalétique.

Ceci permet d’obtenir un meilleur rendement

du climatiseur et évite de surcharger les circuits

électriques du domicile qui risque d’occasionner

un incendie en surchauffant.

Consultez les Consignes d’Installations, dans

la section Exigences Electriques pour les

exigences de branchements électriques

particuliers.

BRANCHEMENTS ÉLECTRIQUES

Consignes

de sécurité

Consignes d’utilisation

Entretien et nettoyage

Instructions

de montage

Conseils de dépannage

Assistance à

la clientèle

20

La page charge ...

GE AEE08 Le manuel du propriétaire

GE AEE08 Le manuel du propriétaire

dans d''autres langues

Documents connexes