Avanti DW1831D0WE Le manuel du propriétaire

DISHWASHER / LAVAPLATOS / LAVE-VAISSELLE

INSTRUCTION MANUAL / MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Model Numbers

Números de modelos

Numéros de modèle

DW1831D0WE

DW1832D1BE

DW1833D3SE

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING

INSTRUCTIONS.

Avanti has a policy of continuous improvement on its products and reserves the right to change materials and

specifications without notice.

Avanti Products LLC

P.O. Box 520604 - Miami, Florida 33152

www.avantiproducts.com

2

TABLE OF CONTENTS

Help Us Help You

3

Parts and Features

4

Important Safety Instructions

5

Electrical Connection

5

Water Heater Safety

6

Before Using Your Dishwasher

6

Control Panel

7

Wash Cycle Descriptions

7 - 8

Overflow Protection

9

Using the Detergent Dispenser

9

Using the Rinse Aid Dispenser

10

How to Efficiently Load Your Dishwasher

11

Starting, Modifying and Canceling the Wash Cycle

12

Filtering System

12

Caring and Maintenance

13

Cleaning the Spray Arms

13

Cleaning the Filters

13

Cleaning the Door

13

How to Keep your Dishwasher in Shape

14

Problems with your Dishwasher?

14

Troubleshooting Guide

14 - 15

Service for your Dishwasher

16

Wiring Diagram

16

Your Avanti Products Warranty

17

Instrucciones en Español

18 - 32

Instructions en Francais

33 - 48

Registration Information / Registration Card

Back Cover

3

Read this guide carefully.

HELP US HELP YOU...

Write down the model and serial numbers.

You'll find them on a plate located on the rear

It is intended to help you operate and maintain

your new dishwasher properly.

Keep it handy to answer your questions.

If you don't understand something or you need

more assistance, please call:

Avanti Customer Service

800-220-5570

Keep proof of original purchase date (such as

your sales slip) with this guide to establish the

warranty period.

wall of the dishwasher.

Please write these numbers here:

____________________________________

Date of Purchase

____________________________________

Model Number

____________________________________

Serial Number

Use these numbers in any correspondence or

service calls concerning your dishwasher.

If you received a damaged dishwasher,

immediately contact the dealer (or builder) that

sold you the dishwasher.

Save time and money. Before you call for

service, check the Troubleshooting Guide. It

lists causes of minor operating problems that

you can correct yourself.

IF YOU NEED SERVICE

We're proud of our service and want you to be

pleased. If for some reason you are not happy

with the service you receive, here are some

steps to follow for further help.

FIRST, contact the people who serviced your

dishwasher. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the

details, including your telephone number, and

send it to:

Customer Service

Avanti Products

10880 NW 30

th

Street

Miami, FL 33172

4

PARTS AND FEATURES

1

Door Lock

2

Upper Rack

3

Upper Spray Arm

4

Silverware Basket

5

Lower Rack

6

Lower Spray Arm

7

Detergent / Rinse Aid Dispenser

8

Cup Shelf

9

Heating Element

5

Important Safety Instructions

WARNING

To reduce the risk of fire, electrical shock, or injury when

using your dishwasher, follow these basic precautions:

Read all instructions before using the dishwasher.

DANGER or WARNING: Risk of child entrapment.

Child entrapment and suffocation are not problems of the past. Junked or abandoned

dishwashers are still dangerous. . . even if they will “just sit in the garage a few days.”

Before you throw away your old appliance: Take off the doors. Leave the shelves in

place so that children may not easily climb inside.

Never allow children to operate, play with, or crawl inside the dishwasher.

Never clean dishwasher parts with flammable fluids.

Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of

this or any other dishwasher.

Plug the dishwasher into an exclusive properly installed-grounded wall outlet. Do not

under any circumstances cut or remove the third (ground) prong from the power cord.

Any questions concerning power and or grounding should be directed toward a certified

electrician or an authorized Avanti Products service center

-Save these instructions-

Electrical Connection

This dishwasher should be properly grounded for your safety. The power cord of this dishwasher is

equipped with a three-prong plug which mates with standard three prong wall outlets to minimize

the possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the power cord

supplied.

Never use an extension cord to connect power to the unit.

Never use a two-prong grounding adapter.

Where a two-prong wall receptacle is encountered, contact a qualified electrician to have it replaced

with a 3-prong receptacle in accordance with applicable electrical codes.

This dishwasher requires a standard 110/120 volts A.C.~/60hz electrical outlet with three-prong

ground.

The cord should be secured behind the dishwasher and not left exposed or dangling to prevent

accidental injury.

Connect to a grounded metal, permanent wiring system: or run an equipment grounding terminal or

lead of the appliance.

Improper connection of the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative if you are in doubt whether the appliance

is properly grounded.

Do not attempt to repair or replace any part of your dishwasher unless it is specifically

recommended

in this manual. All other servicing should be referred to a qualified technician.

To minimize the possibility of electric shock, disconnect this appliance form the power supply before

attempting any maintenance. Note: Turning the dishwasher off does not disconnect the appliance

from the power supply. We recommend having a qualified technician service your appliance.



Warning



Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is

damaged, have it replaced by an authorized Avanti Products service center.

6

Water Heater Safety

Under certain conditions hydrogen may be produced in a water heater that has not been used for two

weeks or more. Hydrogen gas is explosive.

If the hot water has not been use for two weeks or more, prevent the possibility of damage or injury by

turning on all hot water faucets and allow them to run for several minutes. Do this before using any

electrical appliance which is connected to the hot water system. This simple procedure will allow any

built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or

appliance during this process.

Use this appliance only for its intended purpose as described in this Owner’s Manual.

WARNING

READ FOR PROPER USE

Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.

Do not touch the heating element during or immediately after use.

Do not wash plastic items unless they are marked dishwasher safe or the equivalent. For plastic

items not so marked, check the manufacturer recommendations.

Use only detergent and rinse additives designed for an automatic dishwasher. Using detergent that

is not specifically designed for dishwashers will cause the dishwasher to fill with suds.

Keep children away from detergent and rinse aid, keep children away from the open door of the

dishwasher, there could still be some detergent left inside.

The door should not be left in the open position since this could present a tripping hazard.

During installation, the power supply must not be excessively bent or flattened.

To reduce the risk of injury, do not allow children to play in or on a dishwasher.

Do not operate your dishwasher unless all enclosure panels are properly in place. Open the door

very carefully if the dishwasher is operating, there is a risk of water squirting out.

Do not place any heavy objects or stand on the door when it is open. The appliance could tip

forward.

When loading items to be washed:

1)

Locate sharp items so that they are not likely to damage the door seal;

2)

Load sharp knives with the handles up to reduce the risk of cut-type injuries.

When using your dishwasher, you should prevent plastic items form contacting with heating

element.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or

similarly qualified person in order to avoid a hazard.

Please dispose of packing materials properly.

Use the dishwasher only for its intended function.

Remove the door when removing an old dishwasher from service or discarding it.

Do not tamper with controls.

Do not touch the heating element during or immediately after use.

Before Using Your Dishwasher

Remove the exterior and interior packing.

Check to be sure you have all of the following parts:

2 Wash Racks (1 Upper / 1 Lower)

1 Silverware Basket

1 Measuring Spoon

1 Instruction Manual

1 Measuring Cup

1 Installation Manual

Clean the interior surface with lukewarm water using a soft cloth.

7

CONTROL PANEL

Once the program has been selected the appropriate indicator light will flash/blink

intermittently

Pre-Programmed Wash Cycles

Program

Cycle

Selection

Information

Description

of Cycle

Running

time

Rinse

Aid

Heavy

For the heaviest soiled

loads, such as pots, pans,

casserole dishes and

dish

es

that have been

sitting with dried food on

them for a

Pre-wash

Wash

Rinse

Drying

2:10

Normal

(AHAM)

For normally soiled loads

,

such as pots,

plates,glasses and lightly

soiled pans. standard

daily

cycle.

Pre-wash

Wash

Rinse

Drying

2:05

ECO

For lightly soiled

loads,such as

plates,glasses,bowls and

lightly soiled pans.or

silverware.

Wash

Rinse

Drying

2:00

Glass

For lightly soiled loads,

such as glasses, crystal

and fine china.

Pre-wash

Wash

Rinse

Drying

1:35

Rapid

A

shorter wash for lightly

soiled

loads that do not

need

drying.

Pre-wash

Wash

Rinse

Drying

1:00

Rinse

Use for rinsing dishes,

glasses and silverware that

will not be washed right

away.

Pre-wash

Wash

20 Mins

1

Program Selector Buttons

5

Delay Program Selector Button

2

Option Indicator Lights

6

Digital Display Window

3

Options Selector Button

7

Start / Cancel Button

4

Panel Lock – Press and hold both

buttons for approximately 3

seconds

8

Cycle Status Indicator Lights

8

Wash Options:

SANITIZE:

AVAILABLE ONLY ON HEAVY, NORMAL AND ECO PROGRAMS

When the Sanitize option is selected, the water temperature will be maintained at 156ºF/69ºC

(maximum). The maximum temperature may not be reached if the incoming water temperature

is not adequate.

Residential dishwashers are not intended for licensed food establishments or Commercial

applications.

HI-TEMP:

When the HI-Temp option is selected, the water temperature will be maintained at 140ºF/60ºC

(maximum). The maximum temperature may not be reached if the incoming water temperature

is not adequate.

Residential dishwashers are not intended for licensed food establishments or Commercial

applications.

HEATED DRY:

When the “Heated Dry” function is selected, the heater will work throughout the drying

process.

DELAY:

To delay the start of a selected cycle, press the Delay Start button until the desired delay time

shows in the LED display. You can delay the start time for 1 to 24 hours. To cancel the delay

start option before the set delay period is over, simply press the START/CANCEL button for 3 –

5 seconds.

CYCLE PROCESS INDICATOR LIGHTS:

Indicators are located at the right hand side of the control panel.

These lights indicate which stage of the program cycle the unit is working in.

9

OVERFLOW PROTECTIONS

Our Avanti dishwasher has an overfill protection device which could automatically shut off the inlet valve

and start the drain pump if the water overflow. If this occurs, turn off the main water supply before calling

a servicer. If there is water in the base pan because of an overfill or small leak, the water should be

removed before restarting the dishwasher.

DETERGENT DISPENSER

TO PREVENT THE FORMATION OF DETERGENT DEPOSITS DO NOT ADD EXCESS AMOUNT OF

DETERGENT AS YOUR DISHWASHER HAS A SPECIALLY DESIGNED WATER SOFTNER.

The dispenser must be refilled before the start of each wash cycle following the instructions provided in

the “Wash Cycle Table”. Your dishwasher uses less detergent and rinse aid than conventional

dishwashers. Generally, only one teaspoon of detergent is needed for a normal wash load, heavily

soiled items may need more detergent. Always add the detergent just before starting the dishwasher,

otherwise it could become damp and not dissolve properly.

Amount of Detergent to Use

IF THE WATER IN YOUR AREA IS NOT TOO HARD, YOU MAY ALSO PREVENT THE FORMATION

OF DEPOSITS BY DETERGENT

The amount of detergent needed can vary due to differences in the water hardness of your area. To

determine the water hardness in your area, contact your local water utility or area water softening

company. The harder the water, the more detergent you may need. Remember, you should adjust the

amount of detergent you use by small amounts until you find the correct amount.

Removing Hard Water Spots From Dishes

To remove hard water spots, try the following:

Run dishes through a normal wash program.

Remove all metal dishware, such as cutlery, pans, etc., from the

dishwasher.

Do not add detergent.

Pour two cups of vinegar into a bowl and set the bowl face up on the lower

rack of the dishwasher.

Run the dishes through a normal wash program.

If this doesn’t work, try the same process with ¼ cup of citric acid crystals instead of vinegar.

Proper Use Of Detergent

Use only detergent specifically made for use in dishwasher. Keep your detergent fresh and dry. Don’t

put powder detergent into the dispenser until you’re ready to wash dishes.

10

Rinse Aid Dispenser

•

Your dishwasher is designed to use liquid rinse aids. The rinse-aid dispenser is located on the door

next to the detergent dispenser. Fill the rinse-aid dispenser until the level indicator turns completely black

(approximately 100ml of liquid rinse-aid). Be sure not to overfill the dispenser as this will cause over-

sudsing. Wipe away any spills with a damp cloth. Keep in mind that if you have soft water, you may not

need to use a rinse-aid as it may cause a white film to develop on your dishes.

•

To open the dispenser, turn the cap to the “Open” arrow (counter-clockwise) and lift outward.

•

Pour the rinse-aid into the dispenser, being careful not to overfill.

•

Replace the cap by inserting it by aligning the arrow to the open position and turning clockwise to

close it.

•

The rinse-aid is released during the final rinse to prevent water from forming droplets on your dishes

that can leave spots and streaks. It also improves drying by allowing the water to “sheet” off the dishes.

Adjusting Rinse Aid Dispenser

A measured amount of rinse aid is released during the final rinse. As with detergent, the amount of

rinse aid needed for your dishes depends on the hardness of the water in your area. Too much rinse

aid can result in lather of foaming and cause cloudiness or streaks on your dishes. If the water in your

area is very soft, you may not need rinse aid. If you do, you can dilute the rinse aid with an equal amount

of water.

When To Refill The Rinse Aid Dispenser

If there is no rinse aid warning light on the control panel, you can judge

the amount of rinse aid by the following means: The black dot on the

rinse aid dispenser indicates the amount of rinse aid in the dispenser.

As the rinse aid diminishes, the size of the black dot decreases. You

should never let the rinse aid get below ¼ full.

11

How to Use the Upper Rack

The upper rack is designed to hold more delicate and lighter dishware such

as glasses, coffee and tea cup and saucers, as well as plates, small bowls and

shallow pans ( as long as they are not too dirty). Position the dishes and

cookware so that they do not get moved by the spray of water.

The upper rack can be adjusted for height by putting wheels of different

height into the rails.

How To Use The Lower Rack

We recommend that you place large items which are most difficult to clean into the lower rack: pots, pans,

lids, serving dishes and bowls, as shown in the figure below.

It is preferable to place serving dishes and lids on the side of the racks in

order to avoid blocking the rotation of the top spray arm.

Pots, serving bowls, etc, must always be placed top down.

Deep pots should be slanted to allow water to flow out.

The bottom rack features fold down tine rows so that larger or more pots and

pans can be loaded.

Silverware Basket

Silverware should be placed in the silverware basket with handles at the

bottom: if the rack has side baskets, the spoon should be loaded individually into the appropriate slots,

especially long utensils should be placed in the horizontal position at the front of the upper rack.

12

Starting A Wash Cycle

Make sure that the plug for the appliance is inserted into the wall socket.

Make sure the water supply is turned on to full pressure.

Load the dishwasher.

Pour in the detergent.

Close the door completely.

Select the appropriate wash cycle suitable for your needs the dishwasher will begin the selected wash

cycle.

Canceling Or Modifying A Wash Cycle Setting

Premise: A cycle that is underway can only be modified if it has only been running for a short time.

Otherwise, the detergent may have already been released, and the appliance may have already drained

the wash water. If this is the case, the detergent dispenser must be refilled. Press the START/CANCEL

button to hold for more than 3 seconds to cancel the running program. Then you can select appropriate

programs.

At The End Of The Wash Cycle

Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they

are still hot and more susceptible to breakage. They will also dry better.

Forgot To Add A Dish?

A forgotten dish can be added any time before the detergent cup opens.

Press the START/CANCEL button

Pull the door handle.

Do not open the door until the water spray action stops. Steam may rise out of the dishwasher.

Add forgotten dishes.

Push the door to close it. When the door is closed right a click will be heard.

Press the START/CANCEL button again to continue accordingly.

Filtering System

For your convenience, we have placed the drain pump and filtering system within easy reach inside the tub.

There are three components of the filtering system: the main filter, the coarse filter and the fine filter.

1.

Main Filter

Food and soil particles trapped by this filter are pulverized by a special jet on the lower

spray arm and washed down the drain.

2.

Coarse Filter

Larger items, such as pieces of bone or glass, that could clog the drain are trapped in the coarse filter. To

remove an item caught in this filer, gently squeeze the tabs on top of this filter and lift out.

3.

Fine Filter

This filter holds soil and food residue in the sump area and prevents it from being re-deposited on the

dishes during a cycle.

13

Caring And Maintenance

To clean the control panel use a lightly dampened cloth then dry thoroughly. To clean the exterior use a

good appliance polish wax.

Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.

Protect against freezing

If you dishwasher is left in an unheated place during the winter, ask a service technician to:

1.

Cut off electrical power to the dishwasher. Remove fuses or tip circuit breaker.

2.

Turn off the water supply and disconnect the water inlet pipe from the water valve.

3.

Drain water from the inlet pipe and water valve. (Use a pan to catch the water.)

4.

Reconnect the water inlet pipe to the water valve.

5.

Remove the plastic sump cover in the tub the bottom and use a sponge to soak up water in rubber

boot.

Cleaning The Spray Arms

It is necessary to clean the spray arms regularly or hard water chemicals will clog the

spray arm jets and bearings. To remove the spray arm, screw off the nut to take out

the washer on top of the spray arm and remove the arm. Wash the arms in soapy and

warm water and use a soft brush to clean the jets. Replace them after rinsing them

thoroughly.

Cleaning The Filters

Filter assembly

Turn the Coarse filter in a counter-clockwise

direction and lift outward.

1.

Lift out the Main filter

2.

Lift out the Fine filter.

To replace the filter follow the same steps in

reverse.

For best performance and results, the filter

assembly must be cleaned.

The dishwasher must never be used without the

filters. Improper replacement of the filter may

reduce the performance level of the appliance and

damage dishes and utensils.

WARNIING – Never run the dishwasher without the filters in place.

Cleaning The Door

To clean the edge around the door, you should use only a soft warm, damp rag. To

prevent penetration of water into the door lock and electrical components, do not use

a spray cleaner of any kind.

Also, never use abrasive cleaners or scouring pads on the outer surfaces because

they will scratch the finish. Some papers towels can also scratch or leave marks on

the surface.

WARNING - Never use a spray cleaner to clean the door panel for it could damage the door lock

and electrical components. It is not allowed to use the abrasive agent or some paper towel

because of the risk of scratching or leaving spots on the stainless steel surface.

14

How To Keep You Dishwasher In Shape

After every wash

After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that

moisture and odors are not trapped inside.

No solvents or abrasive cleaning products

To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning

products. Rather, use only a cloth and warm soapy water. To remove spots or stains from the surface of

the interior, use a cloth dampened with water and a little white vinegar, or a cleaning product made

specifically for dishwashers.

When you go on Holiday

When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and

them remove the plug from the AC socket, turn off the water supply and leave the door of the appliance

slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance.

Seals

One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals.

Periodic cleaning with a damp sponge will prevent this from occurring.

PROBLEMS WITH YOUR DISHWASHER?

You can solve many common dishwasher problems easily, saving you the cost of a possible service

call. Try the suggestions below to see if you can solve the problem before calling the servicer.

TROUBLESHOOTING GUIDE

PROBLEM

POSSIBLE CAUSE

WHAT TO DO

Dishwasher does not

operate.

The circuit breaker tripped

or blown fuse.

Power supply is not turned

on.

Water pressure is low.

Replace fuse or reset circuit breaker. Remove any

other appliances sharing the same circuit with the

dishwasher

Make sure the dishwasher is turned on and the

door is closed securely.

Make sure the power cord is properly connected.

Check that the water supply is connected properly

and the water is turned on.

Drain pump doesn’t stop

Overflow

The system is designed to detect an overflow.

When it doesn’t it shuts off the circulation pump

and turns on the drain pump.

Noise

Some audible sounds are

normal.

Utensils are not secured in

the baskets or something

small has dropped into the

basket.

Motor hums.

Sound from soft food shredding action and

detergent cup opening.

Ensure everything is secured in the dishwasher.

Dishwasher has not been used regularly. If you do

not use it often, remember to set it to fill and pump

out every week, which will help keep the seal

moist.

Suds in the tub

Improper detergent.

Spilled rinse agent.

Use only the special dishwasher detergent to avoid

suds.

If this occurs, open the dishwasher and let suds

evaporate.

Add 1 gallon of cold water to the tub. Close and

latch the dishwasher, then drain out the water by

slowly turning the dial until a drain period is

reached. Repeat if necessary.

Always wipe-up rinse agent spills immediately.

Stained tub interior

Detergent with colorant was

Make sure that the detergent is the one without

15

used.

colorant.

Dishes are not dried

Rinse agent dispenser is

empty.

Make sure the rinse agent dispenser is filled.

Dishes and flatware not

clean.

Improper program.

Improper rack loading.

Select a stronger program.

Make sure that the action for the detergent

dispenser and spray arms are not blocked by large

dishware.

Cloudiness on glassware.

Combination of soft water

and too much detergent.

Use less detergent if you have soft water and

select a shorter cycle to wash the glassware to get

them clean.

Yellow or brown film on

inside surfaces.

Tea or coffee stains.

Iron deposits in water can

cause an overall film.

Using a solution of ½ cup bleach and 3 cups warm

water to remove the stains by hand.

Warning

You have to wait for 20 minutes after a cycle to let

the heating elements cool down before cleaning

interior: otherwise, burns will happen.

You have to call a water softener company for a

special filter.

White film on inside surface.

Hard water minerals

To clean the interior, use a damp sponge with

dishwasher detergent and wear rubber gloves.

Never use any other cleaner than dishwasher

detergent for the risk of foaming or suds.

Detergent left in dispenser

cups.

Dishes block detergent

cups.

Re-load the dishes properly.

Steam

Normal phenomenon

There is some steam coming through the vent by

the door latch during drying and water draining.

Black or gray marks on

dishes.

Aluminum utensils have

rubbed against dishes.

Use a mild abrasive cleaner to eliminate those

marks.

Water standing in the bottom

of the tub.

This is normal.

A small amount of clean water around the outlet on

the tub bottom at the back of the tub keeps the

water seal lubricated.

Water doesn’t pump out of

the tub.

Drain is clogged.

Make sure the kitchen sink is draining well. If the

dishwasher drains into a disposer, run it clear.

Dishwasher leaks.

Overfill dispenser or rinse

aid spills.

Dishwasher isn’t level.

Be careful not to overfill the rinse aid dispenser.

Spilled rinse aid could cause oversudsing and lead

to overflowing. Wipe away any spills with a damp

cloth.

Make sure the dishwasher is level.

LIGHT and QUICK program

lights flicker intermittently

Water has not reached the

required temperature (HOT)

Malfunction of the temperature sensor and or the

heating element

NORMAL and LIGHT

program lights flicker

intermittently

Failure of the temperature

sensor

Temperature sensor has failed.

Contact an authorized service center

NORMAL and QUICK

program lights flicker

intermittently

Failure of the temperature

sensor

Temperature sensor has failed.

Contact an authorized service center

16

SERVICE FOR YOUR DISHWASHER

We are proud of our customer service organization and the network of professional service technicians

that provide service on your Avanti dishwashers. With the purchase of your Avanti dishwasher, you can

have the confidence that if you ever need additional information or assistance, the Avanti Products

Customer Service team will be here for you. Just call us toll-free.

AVANTI PRODUCTS CUSTOMER SERVICES

Product Information

800-323-5029

Whatever your questions are about our products,

help is available.

Part Orders

800-220-5570

You may order parts and accessories that will be

delivered directly to your home, by personal

check, money order, Master Card, or Visa.

In-Home Repair Service

800-220-5570

An Avanti Products authorized service center will

provide expert repair service, scheduled at a time

that is convenient for you. Our trained servicers

know your dishwasher inside and out.

Wiring Diagram

17

YOUR AVANTI PRODUCTS

WARRANTY

Staple your sales receipt here. Proof of original

purchase date is needed to obtain service under

warranty.

WHAT IS COVERED – LIMITED ONE-YEAR WARRANTY

Avanti Products warrants that the product is free from defects in materials and/or workmanship for a period of

twelve (12) months from the date of purchase by the original owner. The foregoing timeline begins to run upon the

date of purchase, and shall not be stalled, tolled, extended, or suspended for any reason whatsoever unless

described in detail in the warranty document. For one year from the date of purchase by the original owner, Avanti

products will, at its option, repair or replace any part of the product which proves to be defective in material or

workmanship under normal use. Avanti Products will provide you with a reasonably similar product that is either

new or factory refurbished. During this period Avanti Products will provide all parts and labor necessary to correct

such defects free of charge, so long as the product has been installed and operated in accordance with the written

instructions in this manual. In rental or commercial use, the warranty period is 90 days. All Avanti appliances of 3.5

cubic feet capacity or less must be brought/sent to the appliance service center for repair.

THIS SECTION APPLIES TO CLOTHES WASHERS ONLY

LIMITED FIVE YEAR WARRANTY ON PLASTIC TUB

After one year and until five years from the date of purchase, Avanti Products will furnish a replacement plastic tub,

for one which is defective in material or workmanship. All labor and transportation charges are the responsibility of

the consumer.

LIMITED SEVEN YEAR WARRANTY ON STAINLESS STEEL TUB

After one year and until seven years from the date of purchase, Avanti Products will furnish a replacement plastic

tub, for one which is defective in material or workmanship. All labor and transportation charges are the

responsibility of the consumer.

WARRANTY EXCLUSIONS / WHAT IS NOT COVERED:

The warranty coverage described herein excludes all defects or damage that are not the direct fault of Avanti

Products, including without limitation, one or more of the following:

•

A failure to comply with any applicable state, local, city, or county electrical, plumbing and/or building codes,

regulations, or laws, including failure to install the product in strict conformity with local fire and building codes

and regulations.

• Any external, elemental and/or environmental forces and factors, including without limitation, rain, wind, sand,

floods, fires, mud slides, freezing temperatures, excessive moisture or extended exposure to humidity, lightning,

power surges, structural failures surrounding the appliance, and acts of God.

•

Incidental or consequential damages

• Parts and labor costs for the following will not be

considered as warranty:

• Door springs, and/or frames.

• Inner door panels, door shelves, door rails, and/or

door supports.

• Shipping and handling costs associated with the

replacement of the unit.

• Repairs performed by unauthorized servicers.

• Service calls that are related to external problems,

such as abuse, misuse, inadequate electrical power,

accidents, fire, floods, or any other acts of God.

• Failure of the product if it is used for other than it

intended purpose.

• The warranty does not apply outside the Continental

USA.

• Surcharges including but not limited to, any after

hour, weekend, or holiday service calls, tolls, ferry

trip charges, or mileage expense for service calls to

remote areas.

In no event shall Avanti Products have any liability or responsibility whatsoever for damage to surrounding property,

including cabinetry, floors, ceilings, and other structures and/or objects around the product. Also excluded from this

warranty are scratches, nicks, minor dents, and other cosmetic damages on external surfaces and exposed parts;

Products on which the serial numbers have been altered, defaced or removed; service visits for customer

education, or visits where there is nothing wrong with the product; correction of installation problems (you are solely

responsible for any structure and setting for the product, including all electrical, plumbing and/or other connecting

facilities, for proper foundation/flooring, and for any alterations including without limitation cabinetry, walls, floors,

shelving etc., as well as the resetting of breakers or fuses.

OUT OF WARRANTY PRODUCT

Avanti Products is under no obligation, at law or otherwise, to provide you with any concessions, including repairs,

pro-rates, or product replacement, once this warranty has expired.

Warranty – Washing Machines

18

Lea detenidamente esta

guía.

Ayúdenos a mejorar...

Anote el modelo y número de serie.

Los encontrará en una placa situada en la parte posterior

Se pretende que ayudan a utilizar y mantener

su nuevo lavavajillas correctamente.

Tenga a la mano para responder a sus

preguntas.

Si no entiende algo o si necesita más ayuda,

por favor llame a:

Avanti Servicio al

Cliente 800-220-5570

Mantenga prueba de la fecha de compra

original (como el recibo de venta) con esta

guía para establecer el período de garantía.

pared del lavavajillas.

Por favor, escriba estos números aquí:

____________________________________

Fecha de compra

____________________________________

Número de modelo

____________________________________

Número de serie

Utilice estos números en cualquier

correspondencia o llamadas de servicio en

relación con el lavavajillas.

Si ha recibido un lavavajillas dañado, póngase

inmediatamente en contacto con el distribuidor (o

constructor) que le vendió el lavavajillas.

Ahorrar tiempo y dinero. Antes de llamar al

servicio técnico, consulte la Guía de solución

de problemas. En él se enumeran las causas

de los problemas de funcionamiento de

menor importancia que se puede corregir a sí

mismo.

Si necesita servicio

Estamos orgullosos de nuestro servicio y

queremos que usted esté satisfecho. Si por

alguna razón usted no está satisfecho con el

servicio que recibe, aquí hay algunos pasos a

seguir para obtener más ayuda.

PRIMERA, con alguna de las personas que

al servicio de reparación lavavajillas. Explicar

por qué no está satisfecho. En la mayoría de

los casos, esto va a resolver el problema.

A continuación, si usted todavía no está

contento, escribir todos los detalles,

incluyendo su número de teléfono, y enviarlo

a:

Servicio al cliente

de Avanti Products

10880 NW 30th

Street Miami, FL

33172

19

Partes y características

1

Cerradura de la puerta

2

Rejilla superior

3

Brazo aspersor superior

4

Cesta para cubiertos

5

rejilla inferior

6

Brazo aspersor inferior

7

Detergente / abrillantador

8

Copa del estante

9

Elemento de calefacción

20

Instrucciones de seguridad importantes

ADVERTENCIA

Para reducir el riesgo de incendio, choque eléctrico, o

lesiones personales al usar su lavavajillas, siga estas

Lea todas las instrucciones antes de usar el lavavajillas.

PELIGRO o ADVERTENCIA: Riesgo de atrapamiento de niños.

El atrapamiento y asfixia de niños no son problemas del pasado. Tirados y

abandonados

lavavajillas son un peligro. . . incluso si van a “sentarse en el garaje de

unos días.”

Antes de deshacerse de su viejo aparato: Quite las puertas. Deje los estantes en

su

lugar para que los niños no puedan entrar fácilmente en el interior.

Nunca permita que los niños operen, jueguen, o se introduzcan en el

lavavajillas. Nunca se separa de lavavajillas limpias con líquidos

inflamables.

No almacene o use gasolina u otros vapores y líquidos inflamables en las

proximidades de

este o cualquier otro lavavajillas.

Enchufe el lavavajillas a una toma de tierra adecuada-instalado exclusiva. No haga

bajo

ninguna circunstancia corte o retire la tercera pata (tierra) del cable de alimentación.

Para cualquier duda respecto a la energía y de puesta a tierra o debe ser dirigida a un

electricista certificado o un centro de servicio de Avanti Products

Conexión eléctrica

Este lavavajillas debe estar conectada a tierra adecuadamente para su seguridad. El cable eléctrico de este

lavavajillas es

equipado con un enchufe de tres clavijas que se acopla con tres enchufe de pared

standard para minimizar la posibilidad de choque eléctrico.

Bajo ninguna circunstancia corte o retire la tercera clavija de tierra del cable de alimentación

suministrado.

Nunca utilice un cable de extensión para conectar la energía a

la unidad. Nunca utilice un adaptador de tierra de dos puntas.

¿Dónde se encuentra un receptáculo de pared de dos patas, en contacto con un electricista

calificado para ser sustituido con un receptáculo de 3 clavijas de acuerdo con los códigos

eléctricos aplicables.

Este lavavajillas requiere un estándar de 110/120 voltios AC ~ / 60Hz toma de corriente eléctrica con de tres

clavijas

suelo.

El cable debe estar asegurada detrás del lavaplatos y no dejarlo expuesto para evitar

lesiones accidentales.

Conectarse a un metal con conexión a tierra, sistema de cableado permanente: o ejecutar un terminal de

conexión a tierra del equipo o

ventaja del aparato.

La conexión incorrecta del conductor de protección puede resultar en un riesgo de descarga eléctrica.

Consulte con un electricista o representante de servicio calificado si no está seguro de si el aparato

está correctamente conectado a tierra.

No intente reparar o reemplazar cualquier parte de su lavavajillas a menos que sea específicamente

se

recomienda en este manual. Cualquier otro servicio debe ser realizado por un técnico cualificado.

Para minimizar la posibilidad de choque eléctrico, desconecte este aparato forman la fuente de

alimentación antes

realizar tareas de mantenimiento. Nota: En cuanto el lavavajillas no desconecta

el aparato de la fuente de alimentación. Se recomienda tener un servicio técnico calificado su

aparato.



Advertencia



El uso inapropiado del enchufe a tierra puede resultar en el riesgo de descarga eléctrica. Si el

cable de alimentación está dañado, haga que sea reemplazado por un centro de servicio

autorizado de Avanti Products.

La page charge ...

Avanti DW1831D0WE Le manuel du propriétaire

Avanti DW1831D0WE Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents