JennAir JBFFS42NHP Guide d'installation
- Catégorie
- Frigos
- Taper
- Guide d'installation
GETTING STARTED | 1
GETTING STARTED
BUILT-IN REFRIGERATOR FULL HEIGHT DOOR PANEL KIT
INSTALLATION INSTRUCTIONS
TROUSSE DE PORTE PLEINE GRANDEUR POUR
RÉFRIGÉRATEUR ENCASTRÉ
INSTRUCTIONS D’INSTALLATION
W11172224B
2 | GETTING STARTED
BUILT-IN REFRIGERATOR FULL HEIGHT DOOR PANEL KIT
GETTING STARTED | 3
GETTING STARTED
INTRODUCTION
TABLE OF CONTENTS
INTRODUCTION
INTRODUCTION
SAFETY
You can be killed or seriously injured if
you don't immediately follow instructions.
You can be killed or seriously injured if
you don't immediately follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what can happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER”
or WARNING.”
These words mean:
DANGER
WARNING
INTRODUCTION
Safety ............................................................ 3
Registering Your Product .............................. 4
Product Identication .................................... 4
SITE PREPARATION
Before Installation .......................................... 5
Tools and Parts Required .............................. 5
Tools and Parts Provided .............................. 5
Parts Supplied with Refrigerator ................... 6
Installation Requirements .............................. 7
Plan the Installation ....................................... 7
Opening Requirements .................................. 7
Cabinet and Panel Installation Options ......... 7
Cabinet Cutout Options ................................ 8
Airow and Venting Recommendations ........ 8
Panel Dimensions .......................................... 9
INSTALLATION
Installing Grille Bracket Assembly ................. 10
Installing Air Divider ....................................... 11
Installing Grille Panel ..................................... 12
Removing Film from Panels .......................... 13
Installing Freezer Panel ................................. 14
Installing Door Panel(s) .................................. 15
Moving Refrigerator to Final Position ............ 17
Adjusting Door Swing .................................... 18
Adjusting Freezer Panel ................................. 19
Adjusting Refrigerator Panel(s) ...................... 20
Attaching Panel(s) .......................................... 22
Completing the Installation ............................ 24
TABLE DES MATIÈRES.................27
4 | GETTING STARTED
INTRODUCTION
REGISTRATION
REGISTERING YOUR
PRODUCT
Gain access to our concierge-level Customer Support
by registering your appliance. We make product
registration simple and straightforward so that you
can start using your exclusive Jenn-Air benets
today.
Registering your appliance allows you to:
Streamline your warranty service
If we have your product information, we
can help you faster.
Protect your purchase
In case of an insurance loss, such as re,
ood, or theft, your product registration
could serve as a proof of purchase.
Keep your family safe
We’ll notify you in the rare case of a safety
notication.
Start taking advantage of these benets today by
going on-line to register your product at
jennair.com/customer-care. In Canada, register
your product at jennair.ca.
PRODUCT IDENTIFICATION
Your product identication, which includes the model
and serial numbers, is listed on the product rating
plate.
Recording this information below allows us to more
easily assist you if your product should ever require
service from one of our Jenn-Air Authorized Service
Providers.
Model Number: ________________________________
Serial Number: ________________________________
Date of Installation: ___________________________
Authorized Dealer: ____________________________
Authorized Dealer Phone #: ____________________
INTRODUCTION | 5
INTRODUCTION
SITE PREPARATION
BEFORE INSTALLATION
IMPORTANT:
These instructions are intended as a
general guide only and do not supersede
any national or local codes in any way.
Compliance with all local, state, or national
codes pertaining to this type of installation
should be determined prior to installation.
These instructions are intended to
supplement the Installation Instructions
provided with your refrigerator, not replace
them. Follow the instructions provided with
the refrigerator to install it into the cabinet.
NOTE: The hardware bag contains all
the parts and fasteners needed to install
panels. Most of these components have
been pre-installed on the panels included in
this kit. A hardware bag is shipped with the
refrigerator. You will nd the hardware bag in
either one of the crisper drawers or attached
to the outside of one of the refrigerator
doors.
Pinch Hazard
Installation of door panels with less than a ³⁄₈"
(0.95 cm) gap between the door panel and the
adjacent cabinet increases the risk of potential
pinching.
CAUTION
TOOLS AND PARTS REQUIRED
Assemble the required tools and parts before starting
installation. Read and follow the instructions provided
with any of the required tools listed here. Proper
installation is your responsibility.
Tools Required:
Cordless drill and drill bits
3/8" and 1/2" Open-end wrenches or two
adjustable wrenches
Phillips screwdriver
Small level
Appliance dolly
3/32", 5/32", and 3/16" Hex keys
1/4" and 5/16" Nut drivers
6" Extension nut drivers
Tape measure
TOOLS AND PARTS PROVIDED
Parts Supplied with Panel Kit:
Exterior door panels with handles and
mounting hardware pre-installed.
Instructions
Grille Panel Grille bracket assembly
Foam air divider
Parts Supplied with Refrigerator
(Needed to Install Panel Kit):
Phillips-head at screw
Black: 8281252
Slotted hex-head screw
W10141645
Door stop pin
W10234202
6 | SITE PREPARATION
PARTS SUPPLIED WITH
REFRIGERATOR
The following parts are either not needed to install
the panels in this kit, or they are already installed on
the panels. These parts can be discarded after the
installation is completed:
Panel top bracket
Black: W10667450
“L” brackets
W10234199
Standard grille bracket
W10182743 (left)
W10172741 (right)
Integrated grille bracket
W10260890 (left)
W10260891 (right)
Hex-head pointed screw
W10141189
Hex-head blunt screw
W10142233
Round-head screw
1163283
Shoulder washer
W10471946
Freezer panel brackets
W10606815
SITE PREPARATION
BEFORE INSTALLATION (CONTD.)
SITE PREPARATION | 7
SITE PREPARATION
SITE PREPARATION
INSTALLATION REQUIREMENTS
PLAN THE INSTALLATION
IMPORTANT:
Plan your installation using these instructions in
conjunction with the Installation Instructions provided
with the refrigerator. Modications must be made to
the refrigerator to accommodate the full height door
panels.
Required parts
One of the following built-in refrigerator
models:
42" Side-by-Side: JS42NXFXDE
48" Side-by-Side: JS48NXFXDE
36" Bottom Mount: JB36NXFXLE,
JB36NXFXRE
36" French Door Bottom Mount:
JF36NXFXDE
42" French Door Bottom Mount:
JF42NXFXDE
Steel Panels with handles and Accessory
Full Height Door Panel Kit (which includes
Grille Panel and Grille Bracket Assembly).
OPENING REQUIREMENTS
IMPORTANT:
The width of the opening, from side to side,
must be as specied for your model, for
at least 3" (7.62 cm) back from the face of
the cabinet. If your opening does not meet
this requirement, you will need to make
modications.
The depth of the opening from the front
of the cabinet to the back wall must be
25" (63.5 cm) minimum to achieve a ush
installation.
CABINET AND PANEL INSTALLATION
OPTIONS
Cabinet Depth - 25" (63.5 cm)
Grille Bracket - Top View
Grille Bracket - Side View
AB E
C
D
D
C
B
A
A. Refrigerator door
B.
Full height door panel
C. Side trim
D. Grille bracket
E. Adjacent cabinet
A. Refrigerator door
B.
Full height door panel
C. Side trim
D. Grille bracket
8 | SITE PREPARATION
SITE PREPARATION
CABINET CUTOUT OPTIONS
AIRFLOW VENTING RECOMMENDATIONS
IMPORTANT:
Full height door style installations recommends a minimum of 1/8" (3.2 mm) of open space above the refrigerator. It is recommended that this space not be blocked in
any way, including softs.
Models may be installed using either Option 1, Option 2 or option 3.
Option 1 - Open to Ceiling
Option 2 - False Front (cabinet face only) Option 3 - Closed Soft
Open to ceiling
False front
1/8" (3.2 mm) gap
SITE PREPARATION | 9
SITE PREPARATION
BOTTOM MOUNT MODEL
A
B
C
Legend Model Dimension
A 36" 35
3
/
4
" (90.61 cm)
B 36" 59
1
/
8
" (150.2 cm)
C 36" 20
1
/
2
" (52.07 cm)
FRENCH DOOR BOTTOM MOUNT
MODELS
A A
D
B
C
Legend Model Dimension
A
36"
17
3
/
4
" (45.09 cm)
B 59
1
/
8
"(150.2 cm)
C 20
1
/
2
" (52.07 cm)
D 35
3
/
4
” (90.61 cm)
A
42"
20
3
/
4
" (52.71 cm)
B 59
1
/
8
" (150.2 cm)
C 20
1
/
2
" (52.07 cm)
D 41
3
/
4
" (105.85 cm)
SIDE BY SIDE MODELS
A B
C
Legend Model Dimension
A
42"
17
3
/
4
"(45.14 cm)
B 23
3
/
4
" (60.38 cm)
C 81" (205.7 cm)
A
48"
20
1
/
4
" (51.49 cm)
B 27
1
/
4
" (69.27 cm)
C 81” (205.7 cm)
SITE PREPARATION
PANEL DIMENSIONS
Maximum possible panel weight: 46 lbs (20.9 kg)! Maximum possible panel weight: 34 lbs (15.5 kg)! Maximum possible panel weight: 48 lbs (21.7 kg)!
10 | INSTALLATION
INSTALLATION
INSTALLING GRILLE BRACKET ASSEMBLY
APPLIES TO:
NOTE: If refrigerator is not on rollers, it is
recommended to lower the product to have more
access at the top of product for panel installation. For
ease of grille installation, it is recommended to have
product outside of kitchen cabinet.
1. Remove the three screws fastening each
mounting plate to the top of the refrigerator on
each side. Discard the mounting plates but keep
the screws for attaching the two grille bracket
assemblies provided in this kit.
2. Remove the two screws fastening the air divider
to the unit housing. Discard the air divider, and
reinstall the screws into the holes from where
they were removed.
3. Align the three holes in a grille bracket assembly
with the three holes in a cabinet side, as shown.
Using the screws removed in Step 1, attach the
grille bracket assembly.
4. Repeat step 3 to install the other grille bracket
assembly to the opposite side of the refrigerator.
IMPORTANT: Installing the full height door
panels before removing both existing factory
installed grille brackets can damage the panels.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other
injury.
2
3
10 | INSTALLATION
1
Parts to be used:
X2 Grille bracket assembly
INSTALLATION | 11
INSTALLATION
INSTALLATION
INSTALLING AIR DIVIDER
APPLIES TO:
1. Peel away the paper layer from the foam air
divider to reveal the adhesive side.
2. Stick the foam air divider to unit housing at the
location where metallic air divider was installed
earlier by applying even pressure.
ON
OFF
2
1
Align the base of foam air divider with base of unit housing!
Parts to be used:
X1 Foam air divider
12 | INSTALLATION
APPLIES TO:
1. Position the grille panel between the grille
brackets on each side of the cabinet.
2. Hook the top of grille onto the upper rivet pins.
Rotate downward and push the bottom of the
grille panel in until the grille panel snaps into
place.
NOTE: For grille panel removal, push the top of grille
panel inward until the lower portion snaps out. Rotate
and lift off the grille panel.
INSTALLATION
INSTALLING GRILLE PANEL
1
2
2
12 | INSTALLATION
Parts to be used:
X1 Grille panel
INSTALLATION | 13
INSTALLATION
APPLIES TO:
1. Peel off the film covering on all the door / drawer
panels completely.
NOTE: Gently handle the panels after film is
removed to avoid the panels from external
damages such as scratches.
INSTALLATION
REMOVING FILM FROM PANELS
1
14 | INSTALLATION
12 | INSTALLATION
INSTALLATION
INSTALLING FREEZER PANEL
APPLIES TO:
1. Slightly loosen the bracket screws present on
freezer panel.
2. Slide panel onto drawer. Retighten the four
screws on each side attaching the bracket to the
drawer panel.
3. Using the Phillips-head flat screws, fasten the
panel brackets to the drawer.
4. To allow for later adjustment of the panel, do not
fully tighten the screws attaching the bracket to
the drawer.
IMPORTANT: When you have completed
installing all the panels, check for alignment.
The drawer panel will move up or down to align.
Completely tighten the screws only when panels
are fully aligned.
2
3
1
FOR SIDE BY SIDE MODELS - SKIP THIS STEP!
14 | INSTALLATION
4
Parts to be used:
X6 Phillips-head screws
INSTALLATION | 15
INSTALLATION
APPLIES TO:
1. Open the door(s) and remove the hinge cover(s).
NOTE: French door and bottom mount models
have bottom hinge cover(s) that also must be
removed.
2. Take out the door adjustment pin cover(s) to
expose the adjustment pins.
3. Use foam packaging to prop and hold the door
open while installing a door panel.
INSTALLATION
INSTALLING DOOR PANEL(S)
2
1
3
16 | SITE PREPARATION
INSTALLATION
INSTALLING DOOR PANEL(S) (CONTD.)
4. Align the two shoulder washers, on the back of
the door panel, with the “J” slots on the side of
the refrigerator door.
5. Simultaneously slide the panel onto the door,
and lower the panel bracket down onto the
adjustment pins at the top of the door.
NOTE: On French door and side by side models,
repeat steps 2 through 5 to install the second door
panel.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
panels.
Failure to do so can result in back or other
injury.
4
5
16 | INSTALLATION
INSTALLATION | 17
INSTALLATION
INSTALLATION
MOVING REFRIGERATOR TO FINAL POSITION
APPLIES TO:
1. Gently push back the refrigerator into the cabinet
so that all the panels flush with adjacent cabinets
from all sides.
2. Use a 5/16" Nut driver to turn the leveling bolts
clockwise to raise the refrigerator. Adjust the
leveling bolts until the top of the refrigerator
is making contact with the bottom of the solid
soffit. If the anti-tip boards are used, adjust the
leveling bolts until refrigerator top touches the
bottom of the anti-tip boards. Do not crush unit
housing cover.
IMPORTANT: After height adjustment, ensure
refrigerator is perfectly leveled horizontally. And
ensure panels are flushed with adjacent cabinets.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other
injury.
A
A
B
A. Leveler
A. Rear leveling bolt B. Front leveling bolt
2
1
18 | INSTALLATION
APPLIES TO:
1. If the standard 110° door swing is too wide,
install the door stop pin to allow for a maximum
90° door swing. Insert the door stop pin into the
top hinge in the hole shown. Use a 5/32" hex
key, to tighten door stop pin.
INSTALLATION
ADJUSTING DOOR SWING
1
18 | INSTALLATION
Parts to be used:
Door stop pin (as required)
INSTALLATION | 19
INSTALLATION
APPLIES TO:
1. A 1/8" (3.2 mm) gap is required between the
panel and adjacent cabinets. Use the installation
block to measure the gaps.
INSTALLATION
ADJUSTING FREEZER PANEL
Installation Bloc
k
1
FOR SIDE BY SIDE MODELS - SKIP THIS STEP!
1/8"
20 | INSTALLATION
APPLIES TO:
1. Slightly loosen the panel bracket screws to allow
the panel to move to the left or right.
2. Adjust panels to achieve a 1/8" gap between
panels and adjacent cabinets. For French door
bottom mount and bottom mount models, align
the outside edge of the refrigerator panel to
the outside edge of the freezer panel on both
the sides. For side by side models, align the
refrigerator and freezer panels with adjacent
cabinets.
NOTE: Adjust the panel not the door, if
adjustments are needed to achieve alignment or
required spacing.
3. Tighten the panel bracket screws.
Installation Bloc
k
INSTALLATION
ADJUSTING REFRIGERATOR PANEL(S)
20 | INSTALLATION
1/8"
1
2
3
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
JennAir JBFFS42NHP Guide d'installation
- Catégorie
- Frigos
- Taper
- Guide d'installation