Hoover HI 148 Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
Instruction Book
Washing Machine
English
Français
40002960Eng.qxd 12/04/2005 15:10 Page 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Delivery information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Do’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Don’ts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Choose a location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electricity supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting to the cold water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connection of the machine to the drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Moving the machine into position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adjusting the feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Testing the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Washing advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Loading your washing machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sorting the laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dispensing instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using Inter@ct for the first time. . . . . . . . . . . . . . . . . . . . . . . . 17
Programming the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Wash Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Automatic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Programme Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Special Programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Daily Programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Programme Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
A Typical Wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Selecting the wash programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Starting the wash cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Cleaning and Routine Maintenance. . . . . . . . . . . . . . . . . . . . 34
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Power Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
40002960Eng.qxd 12/04/2005 15:10 Page 2
Introduction
Please read and follow these instructions
carefully and operate the machine accordingly.
This booklet provides important guidelines for
safe use, installation, maintenance and some
useful advice for best results when using your
machine.
Keep all documentation in a safe place for future
reference or for any future owners.
Delivery information
Please check that the following items are
delivered with the appliance:
Instruction manual
Guarantee card
Blanking plug
Inlet hose & hooked end support
(see Unpacking and Installation Instructions)
Base panel & x2 push clips
Energy Label
Do’s
All packaging materials used are
environmentally-friendly and recyclable.
Please help dispose of the packaging via
environmentally-friendly means. Your local
council will be able to give you details of
current means of disposal.
To ensure safety when disposing of an old
washing machine disconnect the mains plug
from the socket, cut the mains power cable
and destroy this together with the plug. To
prevent children shutting themselves in the
machine break the door hinges or the door
lock.
This machine is solely for domestic use,
i.e. to wash, rinse and spin dry household
textiles and garments.
3
Check that no
damage has
occurred to the
machine during
transit. If it has,
call for service
by GIAS.
40002960Eng.qxd 12/04/2005 15:10 Page 3
Don’ts
Do not touch the appliance when hands or
feet are damp or wet.
Do not lean on the door when loading the
machine or use the door to lift or move the
machine.
Do not use adapters, multiple connectors
and/or extensions.
Do not allow children to play with the
machine or its controls.
Do not try to open the door when water is
visible in the drum or the Porte Sécurisée
indicator is on.
4
Failure to
comply with
the above can
compromise the
safety of the
appliance. You
may be charged
for a service call
if a problem
with your
machine is
caused by
misuse.
If the appliance
is not running
properly or
breaks down,
switch it off,
disconnect the
plug from the
socket, turn off
the water
supply and do
not tamper
with the
appliance.
Consult GIAS
Service for
possible repair.
40002960Eng.qxd 12/04/2005 15:10 Page 4
Unpacking the product
Remove the machine from its packaging close to
the final location of the machine.
1. Cut carefully around the base of the
packaging.
2. Lay the machine on its back and remove the
base and the two polystyrene spacers on
each side of the machine. We recommend
that a second person assist in the lifting and
manoeuvring of the machine.
3. Return the machine to the upright position,
remove the remainder of the packaging and
the central screw in the transit bar.
4. Remove the four retaining screws in the
transit bar and pull out the transit bracket.
5
Dispose of the packaging safely.
Make sure it is out of the reach
of children, it is a potential
source of danger.
40002960Eng.qxd 12/04/2005 15:10 Page 5
5. Take the base panel provided and fit the
two self adhesive strips by removing the
backing paper on one side and locating the
strips on each side of the base panel.
6. Tilt the machine forward and locate the
base panel under the front of the machine.
Remove the remaining backing paper from
the self-adhesive strips and offer up the
base panel to the bottom of the cabinet.
7. Take the two plastic fixing clips and fix the
base panel to the base of the machine.
Bring the machine back to the upright
position.
6
We recommend you keep the transit bracket and
screws to protect the machine for future transit.
The manufacturers will not be responsible for any
damage to the machine caused by not following the
instructions relating to releasing the transit protection.
The user is responsible for all installation costs.
40002960Eng.qxd 12/04/2005 15:10 Page 6
8. Cover the central hole in the rear of the
machine with the cap enclosed in the
instruction bag.
Choose a location
After the machine has been installed, ensure
that the mains plug and water supply valves
are easily accessible.
Make sure there is enough space for the
machine. Select a space at least 600mm wide
and 850mm high. Also leave enough space
to open the door fully so you can load and
unload it easily.
Keep the area underneath and around the
machine free of combustible materials such
as lint, paper, rags, chemicals etc.
7
Installation
Do not plug the
machine in and
switch it on at
the mains until
the installation
is completed.
40002960Eng.qxd 12/04/2005 15:10 Page 7
Electricity supply
Washing machines are supplied to operate at a
voltage of 230V, 50 Hz single phase. Check that
the supply circuit is rated to at least 16A.
Electricity can be extremely dangerous.
This washing machine must be earthed.
The socket outlet and the plug on the appliance
must be of the same type.
Do not use multiple adapters and/or extension
leads.
The wires in the mains lead are coloured in
accordance with the following codes:
Blue NEUTRAL
Brown LIVE
Green and Yellow EARTH
CE Appliance complies with European Directive
89/336/EEC, 73/23/EEC and subsequent
amendments.
Water supply
The cold water pressure should be between
0.05-0.8 Mpa.
Do not connect the machine to a single
outlet instantaneous water heater.
The water supply tap should be accessible
when the machine is installed.
Before connecting the fill hose, check that
the water is running from the water supply
tap to be used.
8
You may be
charged for a
service call if a
problem with
your machine is
caused by
incorrect
installation.
If the mains
cord on this
appliance is
damaged, it
must be
replaced by a
special cord
which is ONLY
obtainable from
the GIAS spares
service. It must
be installed by
a competent
person.
40002960Eng.qxd 12/04/2005 15:10 Page 8
This machine has an inlet hose with a 19mm
(3/4") threaded ferrule fitted to the end, to
attach between the threaded connector on the
appliance and the water supply.
Only use the new hose supplied to connect the
machine and ensure that the sealing washers are
in place inside the hose connectors.
Do not re-use old hoses which are attached to
existing installations.
Do not over-tighten the connections. Hand tight
is sufficient.
Do not trap or kink the hose.
1. Connect the elbow end of the hose provided
to the threaded inlet on the back of the
machine.
Grey pipe to the white threaded inlet on
the machine.
2. Hand tighten the connector.
3. Connect the straight ends of the pipes to
the water supply; ensure that there are no
kinks.
4. Turn on the water supply and check for
leaks. If there is a leak, turn off the water
supply, disconnect the hose and check the
sealing washers are in place. Refit the hose
and turn on the water supply.
Aqua-stop
Certain models will be supplied with special hose
that has a double skin and incorporates a water
valve (A). If the inner hose bursts the valve will
automatically shut off the water supply to
prevent flooding. The indicator turns red (B).
Should this happen, turn off the water supply
immediately and obtain a replacement hose from
GIAS Service.
The installation is the same as a conventional
hose with the valve end of the aqua-stop hose
fitted to the water supply.
9
A
B
Connecting to the cold water supply
40002960Eng.qxd 12/04/2005 15:11 Page 9
Connection of the machine to the
drain
This machine must be connected in accordance with the water supply
regulations. Water byelaws prohibit connection to a surface water drain.
Decide which plumbing option suits you best then follow the instructions
below.
Option 1
Waste pipe connection (waste trap)
Fit the hooked end support to the outlet pipe. Position at least 800mm off the
floor.
After removing the blanking plug or cutting the membrane from the waste
system securely fix the outlet pipe to the drainage system, using a hose clip.
Secure the hooked end support up to at least 800mm to avoid water being
drawn back into the machine.
10
All machines are tested with water prior to leaving the
factory so a small amount of water may remain in the
drum and drain hose.
Flooding could occur if any part of the installation is
not completed correctly.
800 mm
hose clip
hooked end support
sink
flexible
discharge hose
trap with hose
adaptor
40002960Eng.qxd 12/04/2005 15:11 Page 10
Option 2
Into a standpipe
Ensure that the standpipe is not located near
an electrical socket.
Fit the hooked end support to the outlet pipe.
Install the hose into the standpipe ensuring
that the pipe is at least 500mm from the floor.
Insert the outlet pipe approximately 100mm
into the standpipe.
Moving the machine
into position
Your machine is heavy so care must be taken
when moving it. We recommend that two people
move the machine to avoid strain and possible
injury.
Take care not to damage flooring when
moving the machine.
When moving the machine to its final
position take care not to kink or damage
the hose at the back of the machine.
Adjusting the feet
Once the machine is in place the feet should be
adjusted to ensure that the machine is level. If
the machine is not level it may become noisy or
move.
Adjust the feet on the front corners of the
machine until the machine is firm and level.
When the machine is firm and level, tighten the
locking nuts on the two feet.
11
Do not drag or
lift the machine
by its door.
100 mm
500 mm min
40002960Eng.qxd 12/04/2005 15:11 Page 11
Refer to the programme guide for details of how
to select programmes.
1. Turn on the water supply and check for
leaks from the fill hose.
2. Switch on the electricity supply.
3. Select the Essorage programme (15) and
then press the Départ/Pause button to start
the machine. Allow the programme to
continue for one minute and then cancel
the programme by returning the selector to
the ARRÊT position. This will remove any
water remaining in the machine from
factory testing.
4. To check for cold water filling to the
machine:
Select the Rinçage programme (14) and
press the Départ/Pause button to start the
machine.
Allow the tumble action to continue until
the water has pumped out. Check that the
drain outlet is not leaking or overflowing.
5. Switch off the machine at the end of the
cycle by turning the programme knob to the
ARRÊT position.
6. Select the Essorage programme (15) and
press the Départ/Pause button to start the
machine. If the machine takes longer than
one minute to empty check the drain hose
for kinks.
Installation testing is now
complete.
Now you have successfully installed the machine
we advise that you run the machine to ensure the
drum is thoroughly clean after testing and
storage. Select COTON RESISTANT 90 and run the
machine for a complete cycle using only wash
detergent and water.
12
Testing the installation
This
programme
will take
approximately
2 hours to
complete.
40002960Eng.qxd 12/04/2005 15:11 Page 12
The following tips are designed to assist in
getting the best results from your machine whilst
utilising it in the most environmentally-friendly
and economical way. It is also important to
understand the items to avoid in your laundry, to
ensure the continued safe and reliable operation
of your machine.
Loading your washing
machine
To make further reductions of energy, water and
detergent consumption, we recommend that you
put a full load into your machine. Energy savings
of up to 50% can be achieved by washing one full
load compared to two half loads.
Do not overload the machine as this will reduce
the quality of the wash and may cause damage
to the machine and your laundry.
When is prewashing really
needed?
Only with particularly dirty loads! Energy savings
of 5 to 15% are made by not selecting the
prewash option for less dirty laundry. Pre-treat
awkward stains with a washable stain remover.
Which wash temperature should
you choose?
Using stain removers before machine washing
reduces the need to wash at temperatures over
60°C.
Using a 40°C wash temperature can make energy
savings of up to 50%.
Heavily soiled laundry
To ensure the best performance when washing a
particularly dirty load, we recommend that you
reduce the amount of items to be put into the
machine. Allowing more space in the drum the
13
Washing advice
40002960Eng.qxd 12/04/2005 15:11 Page 13
items can circulate more freely and will wash
cleaner.
Sorting the laundry
Items to avoid
We recommend that you do not wash underwired
bras in the machine. Should the wires become
detached it could cause damage to your clothes
and the machine. If the washcare label states that
the bra is machine washable then we advise
placing it in a wash bag.
Recommendations
Always follow the wash care labelling on the
garments.
Fasten zips, tie strings and close press studs to
prevent tangling. Ensure that pockets are
emptied of loose change and other small items.
Check that there are no metal objects in the
laundry as these may damage the laundry and
the machine.
Place small items in a wash bag.
14
Do not use the
machine to
wash items that
do not have a
wash label.
Do not wash
items
previously
treated with
solvents.
40002960Eng.qxd 12/04/2005 15:11 Page 14
Detergent dosage
Only use detergents which are suitable for use in a washing machine. You will
obtain the best results from your wash with the minimum use of chemical
products, and the best care for your laundry if you take into consideration the
degree of soiling as well as the type of detergent to choose.
The amount of detergent to use depends on:
Water hardness.
Depending on the hardness of the water and the type of detergent used,
it is possible to reduce the amount of detergent.
The softer the water supply, the less detergent is required.
The degree of soiling.
It is possible to reduce the amount of detergent used depending on the
degree of soiling.
Use less detergent for less soiled items.
Amount of laundry.
It is possible to reduce the amount of detergent when washing only a
small amount of laundry.
For smaller loads use less detergent.
The dosages shown on the packaging of detergents for washing delicates
often already refer to a reduced wash size. Always follow the dosage
instructions on the detergent packaging.
15
The Dispenser
DO NOT exceed the maximum detergent dosage
COMPARTMENT I
Prewash detergent
Maximum dosage 100ml of powder
COMPARTMENT II
Mainwash detergent
Maximum dosage 200ml
of powder
COMPARTMENT
Fabric Conditioner
Maximum dosage 100ml
40002960Eng.qxd 12/04/2005 15:11 Page 15
Dispensing instructions
The detergent drawer is split into 3
compartments:
the first, labelled "I", is for detergent utilised
during Prewash.
the second, labelled "II", is for detergent
utilised during the main wash.
the third, labelled is for special
additives such as fabric softeners, fragrances,
starch, brighteners etc.
Dispensing in the drum
Liquid detergents and some tablets are dispensed
via the machine drum using the recommended
dispensing device which is placed upright on top
of the washload towards the back of the drum.
Some tablets are designed to be placed in the
dispenser drawer, check the detergent pack for
details.
16
Do not put any
items into the
drawer other
than detergents
that are
designed to be
dispensed from
the drawer as
they may cause
blockage or
damage.
40002960Eng.qxd 12/04/2005 15:11 Page 16
17
Using Inter@ct for the first
time
This machine will operate even if you do not programme the Inter@ct set up.
However, this machine has Départ Différé and Programmation Fin Du Cycle
functions and for these functions to work efficiently Inter@ct must be
programmed. This is a simple operation and special care has been taken
during manufacture to ensure that the user can operate this machine simply
and effectively.
Programming the machine
Inter@ct needs to be programmed so that the correct clock setting, language
and personal requirements are set.
When the machine is turned on and the programme dial is moved away from
the ARRÊT position to a programme selection a Welcome message will appear.
This message is displayed for a short time while the machine recognises which
programme has been selected. When the machine is ready, the programme
details will appear on the display and from here you may now beging
programming the machine.
Example:
Please note that when using the Inter@ct menu you have 30 seconds per
operation to make your selection. Should you run out of time, the display will
return to the start screen, and you simply have to re-enter the Inter@ct menu
and continue with the programming.
HOOVER INTER@CT
WELCOME 11:06
1 WHITE COTTON
90° HEAVY 1600 RPM
40002960Eng.qxd 12/04/2005 15:11 Page 17
18
To enter the Menu
Hold down the Super Rapide and the Extra Rinçage buttons together for
5 seconds or until the beep sounds.
The menu options can be changed by pressing the Extra Rinçage button. To
confirm and enter an option press the Super Rapide button.
Set New Time
This function needs to be set for two reasons, firstly to display the current
time of day on the screen and secondly for the Programmation Fin Du
Cycle/Départ Différé settings to work correctly.
You will notice in the display window that the hours on the clock will be
flashing. To set the hours you must press the Extra Rinçage button until the
required figure is displayed. Then press the Super Rapide button to enter the
chosen figure. Now the minutes on the clock will begin to flash. Again press
the Extra Rinçage button until the required minutes are displayed and press
Super Rapide to input the selection.
When you have Set the New Time, the display will ask if you wish to Set the
Time Mode.
Setting the time mode (default setting – ABSOLUTE)
The Set Time Mode allows you choose how you wish the Programme Set End
Time and Start Delay functions to be controlled.
The first, called Absolute Time Mode, allows you to set the actual time you
want the programme to begin or end. An example can be seen below when
the Absolute Time Mode has been selected in the menu set-up stage.
In this example, when setting the Programmation Fin Du Cycle the
programme (as shown above) will end at 08.00.
The second, called Relative Time Mode, allows you to delay the start or end of
your wash cycle by adding hours to the current time displayed on the clock, e.g.
Programme to start/end in 1 hour 30 minutes. An example can be seen below
when Relative Time Mode has been selected is the menu set-up stage.
PROGRAMME END
08:00 14:00
40002960Eng.qxd 12/04/2005 15:11 Page 18
19
In this example, when setting the Programmation Fin Du Cycle the
programme (as shown above) will end at 15:30.
Both options are very useful, but Absolute Time Mode is easier to use since
there is no need for you to calculate how many hours to leave before you
want the machine to end or start your chosen cycle.
You can select which option you require by pressing the Extra Rinçage button
until your preferred option is displayed, and then pressing the Super Rapide
button to accept the option you have chosen.
When you have entered your preferred Time Mode, the display will then ask
for Enable Final Beeping to be set.
Enable Final Beeping (default setting – YES)
Here you have the option to have a beeping alarm to let you know the wash
cycle has finished. By pressing the Extra Rinçage button you can scroll through
the YES and NO options.
To confirm your selection press the Super Rapide button and the screen will
then move to the next stage and ask you if you wish to Enable Memory.
Enable Memory (default setting – NO)
This is a useful feature if you frequently wash laundry using the same
programme. Selecting Enable Memory will tell the machine to remember the
last programme/functions used and set them in the memory. This feature
works only on the Cottons, Delicates, Synthetics and Woollens programmes.
The memory does not retain settings within the Special Programmes group.
Select YES or NO by using the Extra Rinçage button and confirm your
selection by pressing the Super Rapide button.
The display will now show a message asking if you require the Demo Mode to
be set. Please set this option to NO if this has not already been done. This
function is for SERVICE use only. If the demo mode option is set to YES, the
wash programme WILL NOT commence when you exit the Inter@ct 3D menu.
The Demo Mode must be set to NO for the wash cycle to commence. Select
NO using the Super Rapide button and confirm your choice with the Extra
Rinçage button. You will then be asked if you wish to Exit the Menu.
PROGRAMME END
BY 1H 30M 14:00
40002960Eng.qxd 12/04/2005 15:11 Page 19
20
Exit Menu
If you are happy with the settings you have selected, you can now exit the
menu by selecting YES via the Extra Rinçage button and confirm this selection
using the Super Rapide button. However, if you are not happy with some of
the settings selected you must select NO and you can then start programming
again from the beginning. By pressing the Super Rapide button you can enter
and bypass each option individually until you reach the option you would like
to change.
When you are completely satisfied with the menu options you have selected,
you may exit the menu. Testing of the installation may now start. If you wish
to change any of the menu settings at a later date, you can enter the menu as
previously described, run through the menu options from the beginning and
change whichever options you wish. This may be useful for changing Set New
Time when Daylight Saving starts or ends.
Once set, the menu options will remain in the memory of the machine even if
the machine is unplugged or there is a power cut.
40002960Eng.qxd 12/04/2005 15:11 Page 20
1 / 1

Hoover HI 148 Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire

dans d''autres langues