Briggs & Stratton 110000/120000/200000/210000 Manuel utilisateur

Catégorie
Moteur
Taper
Manuel utilisateur
Briggs & Stratton Corporation
Milwaukee, Wisconsin 53201
www.briggsandstratton.com
Copyright 2003 by Briggs & Stratton Corporation
FORM NO. MS-6737-5/03
PRINTED IN U.S.A.
Operating & Maintenance Instructions
Betriebsanleitung & W artungsvorschriften
Drifts- og vedligeholdelsesvejledning
Instrucciones de Mantenimiento & Operación
Instructions d’utilisation et de maintenance
Ïäçãßåò Ëåéôïõñãßáò & Óõíôñçóçò
Istruzioni per l’uso e la manutenzione
Anvisninger for bruk og vedlikehold
Gebruiksaanwijzing
Instruções de operação e de manutenção
Instruktionsbok
Käyttö & Huolto-ohjeet
GB
D
E
DK
F
I
NL
P
SF
S
N
GR
110000, 120000, 200000, 210000
£
¢
¡
©
¤
1
2
3
4
5
6
13
14
15
16
9
10
7
8
11
12
ON
OFF
°C-30
°F
-20 0
20 40 60 80 100
-20 -10 0 10 20 30 40
*
**
32
GB
GB
1
Note: (This note applies only to engines used in the U.S.A.) Maintenance, replacement or repair of the emission control devices and systems may be performed
by any nonroad engine repair establishment or individual. However, to obtain no charge repairs under the terms and provisions of the Briggs & Stratton
warranty statement, any service or emission control part repair or replacement must be performed by a factory authorized dealer.
How To Use Manual Figures
¡ -- ¨ refer to figures inside covers.
-- refer to engine components in figure
¡.
-- refer to part/action in figures.
19
1
Record your engine
Model, Type and Code numbers
here for future use.
Record your date of purchase here for future use.
In the state of California, OHV Model Series 110000 and
120000 engines are certified by the California Air
Resources Board to meet emissions standards for 125
hours; Model Series 200000 and 210000 for 250 hours.
Such certification does not grant the purchaser, owner
or operator of this engine any additional warranties with
respect to the performance or operational life of this
engine. This engine is warranted solely according to
the product and emissions warranties stated else-
where in this manual.
Technical Information
POWER RATINGS: The power ratings for an individual
engine model are initially developed by starting with
SAE (Society of Automotive Engineers) code J1940
(Small Engine Power & Torque Rating Procedure) (Re-
vision 2002-05). Given both the wide array of products
on which our engines are placed, and the variety of en-
vironmental issues applicable to operating the equip-
ment, it may be that the engine you have purchased will
not develop the rated horsepower when used in a piece
of power equipment (actual “on-site” power). This dif-
ference is due to a variety of factors including, but not
limited to, the following: differences in altitude, temper-
ature, barometric pressure, humidity, fuel, engine lu-
brication, maximum governed engine speed, individual
engine to engine variability, design of the particular
piece of power equipment, the manner in which the en-
gine is operated, engine run-in to reduce friction and
clean out of combustion chambers, adjustments to the
valves and carburetor , and other factors. The power
ratings may also be adjusted based on comparisons to
other similar engines utilized in similar applications,
and will therefore not necessarily match the values de-
rived using the foregoing codes.
Engine Components (see fig. ¡)
1
Spark plug wire
2
Air cleaner
3
Choke
4
Carburetor
5
Fuel shut-off valve
6
Rope handle
7
Stop switch/Oil Gard, if equipped
8
Throttle
9
Engine Model Type Code
xxxxxx xxxx xx xxxxxxxx
10
Muffler/Spark arrester , if equipped
11
Fuel fill
12
Fuel tank
13
Oil fill/Dipstick, if equipped
14
Blower housing
15
Oil Drain plug
16
Oil filler plug
Hazard Symbols and Meanings
Explosion
Toxic Fumes
Moving Parts
Shock
Hot Surface
Kickback
Fire
International Symbols and Meanings
On Off
Fuel Shutoff
Read Owner’s
Manual
Stop
Fuel
ChokeSafety Alert
Oil
Safety Precautions
* Briggs & Stratton does not necessarily know what
equipment this engine will power. For that reason,
you should carefully read and understand the
operating instructions for the equipment on which
your engine is placed.
BEFORE OPERATING ENGINE
Read entire Operating & Maintenance Instructions
AND the instructions for the equipment this engine
powers.*
Failure to follow instructions could result in serious
injury or death.
THE OPERATING & MAINTENANCE
INSTRUCTIONS CONTAIN SAFETY
INFORMATION TO
Make you aware ofhazards associatedwith engines
Inform you of the risk of injury associated with those
hazards, and
Tell you how to avoid or reduce the risk of injury.
The safety alert symbol is used to identify safety
information about hazards that can result in personal injury.
A signal word (DANGER, WARNING, or CAUTION) is used
with the alert symbol to indicate the likelihood and the potential
severity of injury. In addition, a hazard symbol may be used to
represent the type of hazard.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION
, when used without the alert symbol,
indicates a situation that could result in damage to
the engine.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer , birth defects, or other reproductive harm.
WARNING
GB
2
WARNING
Gasoline and its vapors are extremely flammable
and explosive.
Fire or explosion can cause severe burns or death.
WHEN ADDING FUEL
Turn engine OFF and let engine cool at least 2
minutes before removing gas cap.
Fill fuel tank outdoors or in well-ventilated area.
Do not overfill fuel tank. Fill tank to approximately
1-1/2 inches below top of neck to allow for fuel
expansion.
Keepgasoline away from sparks, open flames, pilot
lights, heat, and other ignition sources.
Check fuel lines, tank, cap, and fittings frequently
for cracks or leaks. Replace if necessary.
WHEN STARTING E NGINE
Make sure spark plug, muffler, fuel cap and air
cleaner are in place.
Do not crank engine with spark plug removed.
If fuel spills, wait until it evaporates before starting
engine.
If engine floods, set choke to OPEN/RUN position,
place throttle in FAST and crank until engine starts.
WHEN OPERATING EQUIPMENT
Do not tip engine or equipment at angle which
causes gasoline to spill.
Do not choke carburetor to stop engine.
WHEN TRANSPORTING EQUIPMENT
Transport with fuel tank EMPTY or with fuel shut-off
valve OFF.
WHEN STORING GASOLINE OR EQUIPMENT WITH
FUEL IN TANK
Store away from furnaces, stoves, water heaters or
otherappliances that have pilot lightor otherignition
source because they can ignite gasoline vapors.
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
If there is natural or LP gas leakage in area, do not
start engine.
Do not use pressurized starting fluids because
vapors are flammable.
WARNING
Unintentional sparking can result in fire or electric
shock.
Unintentional start-up can result in entanglement,
traumatic amputation, or laceration.
BEFORE PERFORMING ADJUSTMENTS OR RE-
PAIRS
Disconnect spark plug wire and keep it away from
spark plug.
Disconnect battery at negative terminal (only
engines with electric start).
WHEN TESTING FOR SPARK
Use approved spark plug tester.
Do not check for spark with spark plug removed.
WARNING
Engines give off carbon monoxide, an odorless,
colorless, poison gas.
Breathing carbon monoxide can cause nausea,
fainting or death.
Start and run engine outdoors.
Do not start or run engine in enclosed area, even if
doors or windows are open.
WARNING
Running engines produce heat. Engine parts,
especially muffler, become extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush,
etc. can catch fire.
Allowmuffler, engine cylinderand fins to cool before
touching.
Remove accumulated combustibles from muffler
area and cylinder area.
Install and maintain in working order a spark
arrester before using equipment on forest-covered,
grass-covered, brush-covered unimproved land.
The state of Californiarequiresthis (Section 4442 of
the California Public Resources Code). Other
states may have similarlaws. Federallaws apply on
federal land.
WARNING
Rotating parts can contact or entangle hands, feet,
hair, clothing, or accessories.
Traumatic amputation or severe laceration can
result.
Operate equipment with guards in place.
Keep hands and feet away from rotating parts.
Tie up long hair and remove jewelry.
Do not wear loose-fitting clothing, dangling
drawstrings or items that could become caught.
WARNING
Rapid retraction of starter cord (kickback) will pull hand
and arm toward engine faster than you can let go.
Broken bones, fractures, bruises or sprains could
result.
When starting engine, pull cord slowly until
resistance is felt, then pull rapidly.
Remove all external equipment/engine loads
before starting engine.
Directcoupled equipment components such as, but
not limited to, blades, impellors, pulleys, sprockets,
etc., must be securely attached.
WARNING
GB
3
Oil Recommendations (see fig. ©)
Engine shipped from Briggs & Stratton without oil.
Before starting engine
, fill with oil. Do not over-fill.
Optional gear reduction may not be filled with oil. If
engine is equipped with gear reduction, see oil
checking/filling instructions (Maintenance, next page).
Use a high quality detergent oil classified “For Service
SF, SG, SH, SJ” or higher such as Briggs & Stratton
30W, Part Number 100005. Use no special additives
with recommended oils. Do not mix oil with gasoline.
Note: Synthetic oil meeting ILSAC
GF-2, API certification mark and API ser-
vice symbol (shown at left) with “SJ/CF
ENERGY CONSERVING” or higher, is an
acceptable oil at all temperatures. Use of
synthetic oil does not alter required oil
change intervals.
* Air cooled engines run hotter than automotive
engines. The use of non-synthetic multi-viscosity
oils (5W-30, 10W-30, etc.)in temperatures above
40° F(4° C) will result in higher than normal oil
consumption. When using a multi-viscosity oil,
check oil level more frequently .
** SAE 30 oil, if used below 40° F(4° C), will result
in hard starting and possible engine bore
damage due to inadequate lubrication.
Check oil level.
Oil Capacity: Models 110000, 120000 is about 21 oz. or
0.6 liter; Models 200000, 210000 is about 28 oz. or 0.8
liter.
Place engine level and clean around oil fill
.
Remove dipstick , wipe with clean cloth, insert and
tighten down again. Remove dipstick and check oil
level. Oil should be at FULL mark
. If oil is required,
add slowly. Do not over-fill.
OR
Remove oil filler plug
. Oil should be full to
overflowing
.
Tighten dipstick or oil filler plug firmly before starting
engine.
Fuel Recommendations
Use clean, fresh, lead-free gasoline with a minimum of
85 octane. Leaded gasoline may be used if it is
commercially available and if unleaded is unavailable.
Purchase fuel in quantity that can be used within 30
days. See Storage.
In U.S.A. leaded gasoline may not be used. Some
fuels, called oxygenated or reformulated gasolines, are
gasolines blended with alcohols or ethers. Excessive
amounts of these blends can damage the fuel system
or cause performance problems. If any undesirable
operating symptoms occur, use gasoline with a lower
percentage of alcohol or ether.
This engine is certified to operate on gasoline. Exhaust
Emission Control System: EM (Engine Modifications).
Do not use gasoline which contains Methanol. Do not
mix oil with gasoline.
For engine protection, we recommend using Briggs &
Stratton Fuel Stabilizer available from an Authorized
Briggs & Stratton Service Dealer.
Check fuel level.
Before refueling, allow
engine to cool 2 minutes.
Clean around fuel fill before removing cap to refuel. Fill
tank to approximately 1-1/2 inches below top of neck to
allow for fuel expansion. Be careful not to overfill.
Starting (see figs. ¢£)
ALWAYS KEEP HANDS AND FEET
CLEAR OF EQUIPMENT MOVING PARTS.
Do not use a pressurized starting
fluid. V apors are flammable.
Start, store and fuel equipment in level position.
CAUTION: Some engines may be equipped with OIL
GARD.TheOIL GARD is intended to warn the
operator that the engine is low on oil. Always check oil
level before starting. Engine damage may occur if the
oil level is not properly maintained and will void
warranty coverage. If the engine will not start, has
stopped running and/or a light flickers in the stop
switch, add oil (see instructions).
Before starting (see fig.
¢)
1. Move choke control
to CHOKE position.
2. Move throttle control to FAST position.
3. Turn fuel shut-off valve ON, if equipped.
4. Move stop control
to ON position, if equipped.
Note: O IL GARD light in rocker stop switch
,if
equipped, warns of low oil level. Light will flicker and en-
gine will not start, or restart. Oil must be added. Fill to
FULL
mark on dipstick or overflowing at oil filler plug.
Do not over-fill. OIL GARD, however, will not stop a
running engine if the engine runs low on oil.
Rewind starter (see fig.
£)
Grasp rope handle and pull slowly until
resistance is felt. Then pull cord rapid-
ly to overcome compression, prevent
kickback and start engine. Repeat i
f
necessary with choke in RUN position and throttle in
FAST. When FAST. When engine starts, operate in
FAST position.
Electric starter (see fig.
£)
On engines equipped with 12 volt starting systems, turn
key to START position
. Repeat if necessary with
throttle control in FAST position. When engine starts,
operate in FAST position.
Note: If equipment manufacturer has supplied battery,
charge it before trying to start engine, as equipment
manufacturer recommends.
Note: Use short starting cycles (15 s ecs. per min.) to
prolong starter life. Extended cranking can damage
starter motor.
Stopping (see fig. ¤)
Do not move choke control to CHOKE position to stop
engine. Backfire or engine damage may occur. Move
throttle control to IDLE or SLOW position
,if
equipped. Then move stop control to OFF position
or turn key to OFF . Close fuel shut-off valve .
Note: Always remove key from switch when equipment
is not in use or left unattended.
Note: When engine is transported, close fuel shut-off
valve to prevent leakage.
Adjustments
To prevent acci-
dental starting, re-
move spark plug
wire and ground
it before adjusting, and disconnect battery at negative
terminal, if equipped.
Throttle control adjustments (see fig.
¥)
Remote control
Loosen casing clamp screw
. Move casing and wire
in direction of arrow to end of travel. Move throttle
control to FAST position
. T ighten casing clamp
screw.
Carburetor adjustment
The manufacturer of the equipment on which
this engine is installed specifies top speed at
which the engine will be operated. DO NOT
EXCEED this speed.
See an Authorized Briggs & Stratton Dealer for
carburetor adjustment.
The carburetor on this engine is low emission. Air/fuel
mixture is not adjustable. It may be equipped with
governed idle. Governed idle and top speed have been
set at the factory. If adjustment is required, see an
Authorized Briggs & Stratton Service Dealer.
Note: Engines operated at about 3000 to 5000 feet
(900 to 1500 meters) above sea level may require a
high altitude carburetor main jet. If erratic performance
is observed, contact a Briggs & Stratton Authorized
Service Dealer for cost to install/purchase a high alti-
tude carburetor main jet, if available.
GB
4
Maintenance (see figs. ¦§¨)
See Maintenance Schedule. Follow the hourly or
calendar intervals, whichever occur first. More frequent
service is required when operating in adverse conditions.
To prevent acci-
dental starting, re-
move spark plug
wire and ground
it before servicing,
and disconnect battery at negative terminal, if equipped.
Oil service (see fig.
¦)
Check oil level regularly.
Be sure correct oil level is maintained. Check every 8
hours or daily , before starting engine. See oil filling
procedure under Oil Recommendations Do not over-fill.
Change oil.
Change oil after first 5 hours of operation. Change oil
while engine is warm. Refill with new oil of recom-
mended SAE viscosity grade. (see fig.
©)
Gear reduction, if equipped
Remove oil fill plug
and oil level plug .Drainoil
every 100 hours of operation or every season. To refill,
pour SAE 30 oil into oil fill hole until it runs out level
check hole. Replace both plugs. Oil fill plug has a vent
hole
and must be installed on top of gear case cover.
Air cleaner service (see fig. §)
Dual element air cleaners
Replace pre-cleaner
and/or cartridge if very dirty
or damaged.
To service pre-cleaner, if equipped, wash in liquid
detergent and water. Squeeze dry in a clean cloth and
allow to dry thoroughly. DO NOT oil pre-cleaner.
To service cartridge, clean by tapping gently on a flat
surface. DO NOT oil cartridge.
Note: Do not use petroleum solvents, e.g., kerosene,
which will cause the cartridge to deteriorate. Do not use
pressurized air
to clean cartridge. Pressurized air can
damage the cartridge.
Rectangular dual element air cleaner
1. Loosen screw and tilt cover down. Remove
pre-cleaner (if equipped) and cartridge assembly
from cover.
2. After servicing pre-cleaner and cartridge, place
pre-cleaner , if equipped (arrows up) over cartridge
pleats (pre-cleaner lip will be at bottom of pleats).
3. Install pre-cleaner and cartridge assembly in cover.
4. Insert tabs on cover into slots
in bottom of base.
5. Tilt cover up and tighten screw securely .
Oval dual element air cleaner
1. Remove knob and cover
. Lift air cleaner off stud.
2. After cleaning, reassemble pre-cleaner on car-
tridge. Push air cleaner firmly down on stud
to
seat in base.
3. Push cover squarely onto base. Tighten knob
securely.
Maintenance Cont’d
Oil foam air cleaner
To service foam element
, wash in liquid detergent
and water. Squeeze dry in a clean cloth. Saturate in
engine oil. Squeeze in clean, absorbent cloth to
remove ALL EXCESS oil.
1. Loosen screw and tilt cover down. Remove
bracket
and foam element from cover.
2. Clean bracket, cover and base.
3. Install bracket and foam element in cover.
4. Insert tabs on cover into slots in bottom of base.
5. Tilt cover up and fasten securely with screw.
Spark plug service (see figs.
§)
Clean/replace spark plug every 100 hours or every
season, whichever occurs first. Spark plug wrench is
available from any Authorized Briggs & Stratton
Service Dealer.
Note: In some areas, local law requires using a resistor
spark plug to suppress ignition signals. If this engine
was originally equipped with resistor spark plug, use
same type of spark plug for replacement.
Spark plug gap
should be .76 mm or 0.030 in.
Keep engine clean (see figs.
¨)
Periodically remove chaff and debris build-up from
engine. Do not spray engine with water to clean
because water could contaminate fuel. Clean with a
brush or compressed air.
A
ccumulation o
f
debris around mu
f
-
fler
could cause a fire. Inspect
and clean before every use.
If muffler is equipped with spark arrester screen
,
remove spark arrester screen for cleaning and inspec-
tion every 50 hours or every season. Replace if
damaged.
To assure smooth operation, keep governor linkage,
springs and controls
free of debris.
Replace in-line
f
uel
f
ilter .Drain
fuel tank or close fuel shut-off valve
before replacing fuel filter.
Clean cooling system. Chaff or debris may clog engine’s
air cooling system, especially after prolonged operation.
Internal cooling fins and surfaces may require cleaning
to prevent overheating and engine damage. Remove
blower housing and clean as shown
.
Check valve clearance:
Model 110000 and 120000 intake .10-.15 mm.
Model 110000 and 120000 exhaust .23--.28 mm.
Model 200000 and 210000 intake .10--.15 mm.
Model 200000 and 210000 exhaust .10--.15 mm.
Maintenance Schedule
Follow the hourly or calendar intervals, whichever
occur first. More frequent service is required when
operating in adverse conditions noted below.
First 5 Hours
D Change oil
Every 8 hours or daily
D Check oil level
D Clean around muffler
Every 25 hours or every season
D Change oil if operating under heavy load or
high ambient temperature
D Service air cleaner pre-cleaner*
Every 50 hours or every season
D Change oil
D Clean and inspect spark arrester, if equipped.
Every 100 hours or every season
D Service oil foam air cleaner or cartridge*
D Clean/replace spark plug
D Change gear reduction oil, if equipped
D Clean cooling system*
Every season
D Check valve clearance
* Clean more often under dusty conditions, or
when airborne debris or chaff is present.
Partial List of Genuine Briggs & Stratton Parts
Briggs & Stratton (or equivalent)
Part
Part No.
Oil (20 oz.) 100005........................
Oil (48 oz.) 100028........................
Oil pump kit (uses standard electric drill 5056.....
to remove oil from engine quickly)
Fuel stabilizer (1 oz., 30 ml single use pouch) 992030
Fuel stabilizer (4.2 oz., 125 ml bottle) 999005E (5041)
Fuel filter 694485.........................
Flat air cleaner cartridge 491588 (5043).........
Flat air cleaner pre-cleaner 493537............
Oval air cleaner cartridge (Model 11, 12) 690610...
Oval air cleaner pre-cleaner (Model 11, 12) 273356.
Oval air cleaner cartridge (Model 20, 21) 692484...
Oval air cleaner pre-cleaner (Model 20, 21) 273930.
Resistor spark plug 802592E.................
Standard spark plug 492167E................
Long life platinum spark plug 5066.............
(used on most OHV engines)
Spark tester 19368........................
Spark plug wrench 19374...................
GB
5
Storage
Engines stored over 30 days need to be protected or
drained of fuel to prevent gum from forming in fuel
system or on essential carburetor parts.
For engine protection, we recommend use of Briggs &
Stratton Fuel Stabilizer available from an Authorized
Briggs & Stratton Service Dealer. Mix stabilizer with fuel
in fuel tank or storage container . Run engine for a short
time to circulate stabilizer through carburetor . Engine
andfuelcanbestoredupto24months.
Note: If stabilizer is not used or if engine is operating on
gasoline containing alcohol, e.g. gasohol, remove all fuel
from tank and run engine until it stops from lack of fuel.
1. Change oil. See Oil service. (see figs.
©¦)
2. Remove spark plug and pour about 15 ml (1/2 oz)
of engine oil into cylinder. Replace spark plug and
crank slowly to distribute oil.
3. Clean chaff and debris from cylinder and cylinder
head fins, under finger guard and behind muffler.
4. Store in a clean and dry area, but NOT near a
stove, furnace or water heater which uses a pilot
light or any device that can create a spark.
Service
See an Authorized Briggs & Stratton Service Dealer.
Each one carries a stock of Genuine Briggs & Stratton
Parts and is equipped with special service tools.
Trained mechanics assure expert repair service on all
Briggs & Stratton engines. Only dealers advertising as
“Authorized Briggs & Stratton” are required to meet
Briggs & Stratton standards.
When you purchase equipment pow-
ered by a Briggs & Stratton engine, you
are assured of highly skilled, reliable
service at more than 30,000 Authorized
Service Dealers worldwide, including
more than 5,000 Master Service Techni-
cians. Look for these signs wherever
Briggs & Stratton service is offered.
You may locate your nearest Authorized Briggs & Stratton
Service Dealer in our dealer locator map on our web site
www.briggsandstratton.com or in the “Yellow
Pages directory under “Engines, Gasoline”
or “Gasoline Engines,” or “Lawn Mowers” or
similar category.
Note: Walking fingers logo and “Yellow Pages” are
registered trademarks in various jurisdictions.
An illustrated shop manual includes “Theories of
Operation,” common specifications and detailed
information covering adjustment, tune-up and repair of
Briggs & Stratton OHV, single cylinder, 4 cycle engines.
Order P/N 272147 from an Authorized Briggs &
Stratton Service Dealer.
Insist on Genuine Briggs & Stratton replacement parts
with our logo on the box and/or part. Non-original parts
may not perform as well and may void your warranty.
BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY
Effective July 1, 2004 replaces all undated Warranties and all Warranties dated before July 1, 2004
LIMITED WARRANTY
Briggs&StrattonCorporation will repair or replace, free of charge,anypart(s)oftheengine that is defective in materialorworkmanshiporboth.Trans-
portation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser.This warranty is effective for the time
periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
www.briggsandstratton.com, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pages’.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PAR-
TICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLI ED WAR-
RANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL D AMAGES ARE EXCLUDED TO THE EXTENT EXCL USION IS
PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not
allow theexclusionorlimitationof incidentalor consequentialdamages,s o theabove limitationand exclusionmay notapply toyou.Thiswarranty gives
you specific legal rights and you may also have other rights which vary from state to state and country to country.
Vanguard
ELS
I/Cr
Industrial Plus
Intek
(Sleeve Bore)
Fource
Intek
(Kool Bore)
Power Built OHV
Quantumr
Quattro
Q45
Sprint
Classic
Commercial Use
2 years
90 days
1 year
Consumer Use
2 years
2 years
90 days
1 year
OUR PRODUCT
WARRANTY PERIOD*
Etek
1 year
* Note the following special warranty periods: 2 years for Classic engines in the European Union and Eastern European countries, for all consumer products in the European Union, and
for e mission control systems on engines certified by EPA and CARB. 5 years for consumer use, 90 days for commercial use of Touch-N-Mow starter on Quantum and Intek engines.
Engines used in competitive racing or on commercial or rental tracks are not warrantied.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer use”
means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once an
engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.
GB
6
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE RECEIPT. IF
YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TI ME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE
PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
ABOUT YOUR ENGINE WARRANTY
Briggs & Stratton welcomes warranty repair and apologizes to
you for being inconvenienced. Any Authorized Service Dealer
may perform warranty repairs. Most warranty repairs are han-
dled routinely, but sometimes requests for warranty service
may not be appropriate. For example, warranty would not apply
if engine damage occurred because of misuse, lack of routine
maintenance, shipping, handling, warehousing or improper
installation. Similarly, warranty is void if the serial number of the
engine has been removed or the engine has been altered or
modified.
If a customer differs with the decision of the Service Dealer, an
investigation will be made to determine whether the warranty
applies. Ask the Service Dealer to submit all supporting facts to
his Distributor or the F actory for review. If the Distributor or the
Factory decides that the claim is justified, the customer will be
fully reimbursed for those items that are defective. To avoid mis-
understanding which might occur between the customer and
the Dealer, listed below are some of thecauses of engine failure
that the warranty does not cover.
Normal wear:
Engines, like all mechanical devices, need periodic parts service
and replacement to perform well. Warranty will not cover repair
when normal use has exhausted the life of a part or an engine.
Improper maintenance:
Thelife of an engine depends upon the conditions under which it
operates, and the care it receives. Some applications, such as
tillers, pumps and rotary mowers, are very often used in dusty or
dirty conditions, which can cause what appears to be premature
wear. Such wear, when caused by dirt, dust, spark plug cleaning
grit, or other abrasive material that has entered the engine be-
cause of improper maintenance, is not covered by warranty.
Thiswarrantycoversenginerelateddefective material and/
or workmanship only, and not replacement or refund of the
equipment to which the engine may be mounted. Nor does
the warranty extend to repairs required because of:
1. PROBLEMS CAUSED BY PARTS THAT ARE NOT
ORIGINAL BRIGGS & STRATTON PARTS.
2. Equipment controls or installations that prevent starting,
cause unsatisfactory engine performance, or shorten en-
gine life. (Contact equipment manufacturer.)
3. Leaking carburetors, clogged fuel pipes, sticking valves,
or other damage, caused by using contaminated or stale
fuel. (Use clean, fresh, lead-free gasoline and Briggs &
Stratton Fuel Stabilizer, Part No. 5041.)
4. Parts which are scored or broken because an engine was
operated with insufficient or contaminated lubricating oil,
or an incorrect grade of lubricating oil (check oil level daily
or after every 8 hours of operation. Refill when necessary
and change at recommended intervals.) OIL GARD
may not shut down running engine. Engine damage may
occur i f oil level is not properly maintained. Read Operat-
ing & Maintenance Instructions.
5. Repair or adjustment of associated parts or assemblies
such as clutches, transmissions, remote controls, etc.,
which are not manufactured by Briggs & Stratton.
6. Damage or wear to parts caused by dirt, which entered
the engine because of improper air cleaner maintenance,
re-assembly, or use of a non-original air cleaner element
or cartridge. (At recommended intervals, clean and re-oil
the Oil-Foam element or the foam pre-cleaner, and
replace the cartridge.) Read Operating & Maintenance
Instructions.
7. Parts damaged by over-speeding, or overheating caused
by grass, debris, or dirt, which plugs or clogs the cooling
fins, or flywheel area, or damage caused by operating the
engine in a confined area without sufficient ventilation.
(Clean fins on the cylinder, cylinder head and flywheel at
recommendedintervals.) Read Operating &Maintenance
Instructions.
8. Engine or equipment parts broken by excessive vibration
caused by a loose engine mounting, loose cutter blades,
unbalanced blades or loose or unbalanced impellers, im-
proper attachment of equipment to engine crankshaft,
over-speeding or other abuse in operation.
9. A bent or broken crankshaft, caused by striking a solid ob-
ject with the cutter blade of a rotary lawn mower, or exces -
sive v-belt tightness.
10. Routine tune-up or adjustment of the engine.
11. Engine or engine component failure, i.e., combustion
chamber, valves, valve seats, valve guides, or burned
starter motor windings, caused by the use of alternate
fuels such as, liquified petroleum, natural gas, altered
gasolines, etc.
Wa rranty is available only through service dealers which
have been authorized by Briggs & Stratton Corporation.
your nearest Authorized Service Dealer is listed in the “Y el-
low Pages of your telephone directory under “Engines,
Gasoline” or “Gasoline Engines,” “Lawn Mowers,” or simi-
lar category.
Briggs & Stratton Engines Are Made Under One Or More Of The Following Patents: Design D-247,177 (Other Patents Pending)
6,691,683
6,647,942
6,622,683
6,615,787
6,617,725
6,603,227
6,595,897
6,595,176
6,584,964
6,557,833
6,542,074
6,520,141
6,495,267
6,494,175
6,472,790
6,460,502
6,456,515
6,382,166
6,369,532
6,356,003
6,349,688
6,347,614
6,325,036
6,311,663
6,284,123
6,263,852
6,260,529
6,242,828
6,239,709
6,237,555
6,230,678
6,213,083
6,202,616
6,145,487
6,142,257
6,135,426
6,116,212
6,105,548
6,347,614
6,082,323
6,077,063
6,064,027
6,040,767
6,014,808
6,012,420
5,992,367
5,904,124
5,894,715
5,887,678
5,852,951
5,843,345
5,823,153
5,819,513
5,813,384
5,809,958
5,803,035
5,765,713
5,732,555
5,645,025
5,642,701
5,628352
5,619,845
5,606,948
5,606,851
5,605,130
5,497,679
5,548,955
5,546,901
5,445,014
5,503,125
5,501,203
5,497,679
5,320,795
5,301,643
5,271,363
5,269,713
5,265,700
5,243,878
5,235,943
5,234,038
5,228,487
5,197,426
5,197,425
5,197,422
5,191,864
5,188,069
5,186,142
5,150,674
5,138,996
5,086,890
5,070,829
5,058,544
5,040,644
5,009,208
4,996,956
4,977,879
4,977,877
4,971,219
4,895,119
4,875,448
4,819,593
4,720,638
4,719,682
4,633,556
4,630,498
4,522,080
4,520,288
4,512,499
4,453,507
4,430,984
D 476,629
D 457,891
D 368,187
D 375,963
D 309,457
D 372,871
D 361,771
D 356,951
D 309,457
D 308,872
D 308,871
¦
§
¨
¥
0.030”
(.76mm)
(This page applicable in the U.S.A. and Canada only.)
Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)
and the United States Environmental Protection Agency (U.S. EPA)
Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations)
EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PUR-
CHASED IN CALIFORNIA IN 1995 AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, AND
TO CERTIFIED MODEL YEAR 1997 AND LA TER ENGINES WHICH ARE PURCHASED AND USED
ELSEWHERE IN THE UNITED STATES (AND AFTER JANUARY 1, 2001 IN CANADA).
California, United States and Canada Emission Control Defects Warranty Statement
The California Air Resources Board (CARB), U.S. EPA and B&S are pleased to explain the Emission
Control System Warranty on your model year 2000 and later small off-road engine (SORE). In Califor-
nia, new small off-road engines must be designed, built and equipped to meet the State’s stringent anti-
smog standards. Elsewhere in the United States, new non-road, spark-ignition engines certified for
model year 1997 and later, must meet similar standards set forth by the U.S. EP A. B&S must warrant
the emission control system on your engine for the periods of time listed below ,provided there has been
no abuse, neglect or improper maintenance of your small off-road engine.
Your emission control system includes parts such as the carburetor, air cleaner, ignition system,
muffler and catalytic converter. Also included may be connectors and other emission related as-
semblies.
Where a warrantable condition exists, B&S will repair your small off-road engine at no cost to you
including diagnosis, parts and labor.
Briggs & Stratton Emission Control Defects Warranty Coverage
Small off-road engines are warranted relative to emission control parts defects for a period of two
years, subject to provisions set forthbelow.If any covered part on your engine is defective, the part
will be repaired or replaced by B&S.
Owner’s Warranty Responsibilities
Asthesmall off-roadengineowner,youareresponsibleforthe performanceofthe requiredmainte-
nance listed in your Operating and Maintenance Instructions. B&S recommends that you retain all
your receipts covering maintenance on your small off-road engine, but B&S cannot deny warranty
solely for the lack of receipts or for your failure to ensure the performance of all scheduled mainte-
nance.
Asthe smalloff-road engineowner,you shouldhowever beawarethatB&Smaydenyyou warranty
coverage if your small off-road engine or a part has failed due to abuse, neglect, improper mainte-
nance or unapproved modifications.
Youareresponsibleforpresenting yoursmalloff-roadenginetoan Authorized B&SServiceDealer
assoon asa problemexists.The undisputed warrantyrepairs shouldbecompleted inareasonable
amount of time, not to exceed 30 days.
If you have anyquestions regarding your warranty rights and responsibilities, you should contact a
B&S Service Representative at 1-414-259-5262.
The emission warranty is a defects warranty. Defects are judged on normal engine performance.
The warranty is not related to an in-use emission test.
Briggs & Stratton Emission Control Defects Warranty Provisions
The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for non-regulated engines found in the Operating and Maintenance Instructions.
1. Warranted Parts
Coverage under this warranty extends only to the parts listed below (the emission control
systems parts) to the extent these parts were present on the engine purchased.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor and internal parts
Fuel Pump
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse valve
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
2. Length of Coverage
B&S warrants to the initial owner and each subsequent purchaser that the Warranted Parts
shall be free from defects in materials and workmanship which caused the failure of the War-
rantedParts for a period of two years from the date the engine is delivered to a retailpurchaser.
3. No Charge
Repair or replacement of any Warranted Part will be performed at no charge to the owner, in-
cluding diagnostic labor which leads to the determination that a WarrantedPart is defective, if
thediagnostic workis performedatanAuthorized B&SService Dealer.Foremissions warranty
service contact your nearest Authorized B&S Service Dealer as listed in the “Yellow Pages”
under “Engines, Gasoline,” “Gasoline Engines,” “Lawn Mowers,” or similar category.
4. Claims and Coverage Exclusions
Warranty claims shall be filed in accordance with the provisions of the B&S Engine Warranty
Policy.Warrantycoverage shallbeexcludedforfailures of WarrantedParts which are not origi-
nal B&S parts or because of abuse, neglect or improper maintenance as set forth in the B&S
Engine Warranty Policy. B&S is not liable to cover failures of Warranted Parts caused by the
use of add-on, non-original, or modified parts.
5. Maintenance
AnyWarrantedPart which isnot scheduled for replacement as required maintenance or which
isscheduledonlyfor regular inspectiontotheeffectof“repairorreplace asnecessary” shall be
warranted as to defects for the warranty period. Any Warranted Part which is scheduled for
replacement as required maintenance shall be warranted as to defects only for the period of
timeupto the first scheduled replacement forthat part. Any replacement part that isequivalent
in performance and durability may be used in the performance of any maintenance or repairs.
The owner is responsible for the performance of all required maintenance, as defined in the
B&S Operating and Maintenance Instructions.
6. Consequential Coverage
Coveragehereundershall extendto thefailureof anyengine componentscaused bythe failure
of any Warranted Part still under warranty.
Look For Relevant Emission Durability Period and Air Index Information On Your Engine Emission Label
Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emission Standards must display information regarding the EmissionsDurability Period and the Air Index. Briggs & Stratton
makes this i nformation available to the consumer on our emission labels. The engine label will indicate certification information.
TheEmission DurabilityPerioddescribes the number of hoursofactualrunningtime for which the engineis certifiedtobeemissioncompliant,assuming proper maintenanceinaccordancewitht he Operating
& Maintenance Instructions. The following categories are used:
Moderate: Engine is certified to be emission compliant for 125 hours of actual engine running time.
Intermediate: Engine is certified to be emission compliant for 250 hours of actual engine running time.
Extended: Engine is certified to be emission compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore, the Emission Durability Period of an engine with an intermediate ratingwouldequateto10to12years.
The Air Index is a calculated number describing the relative level of emission for a specific engine family. The lower the Air Index, the cleaner the engine. This information is displayed in graphical form on the
emission label.
After July 1, 2000, Look For Emissions Compliance Period On Engine Emissions Compliance Label
After July 1, 2000 certain Briggs & Stratton engines will be certified to meet the United States Environmental Protection Agency (USEPA) Phase 2 emission standards. For Phase 2 certified engines, the
EmissionsCompliancePeriodreferred to on the Emissions Compliance l abel indicates the number of operating hours for which theengine has been shown to meet Federal emissionrequirements. For engines
less than 225 cc displacement, Category C = 125 hours, B = 250 hours and A = 500 hours. For engines of 225 cc or more, Category C = 250 hours, B = 500 hours and A = 1000 hours.
The displacement of Model Series 110000 engine is 190 cc, Model Series 120000 engine is 206 cc, Model Series 200000 engine is 305 cc, Model Series 210000 engine is 342 cc.
This is a generic representation
of the emission label typically
found on a certified engine.
(Cette page ne s’applique que pour le Canada et les Etats--Unis)
La Corporation Briggs & Stratton (B&S), le California Air Resources Board (CARB)
et le Bureau de protection environnementale des Etats-Unis (US EPA)
Garantie sur le système d’échappement (Garantie contre les défectuosités, droits et obligations du propriétaire)
LA GARANTIE SUR LE SYSTÈME D’ÉCHAPPEMENT EST APPLICABLE SUR LES MOTEURS
CERTIFIÉSACHETÉS EN CALIFORNIE EN 1995 ET LES ANNÉES SUIV ANTESET QUI SONT UTI-
LISÉS EN CALIFORNIE, AINSI QU’AUX MODÈLES CERTIFIÉS DE 1997 ET LES ANNÉES SUI-
VANTES QUI ONT ÉTÉ ACHETÉS ET UTILISÉS AILLEURS AUX ET ATS--UNIS ET AU CANADA.
Déclaration de garantie sur le système d’échappement pour la Californie, les Etats-Unis et le Canada
Le California Air Resources Board (CARB), le Bureau américain de protection environnementale
(U.S. EPA) et B& S sont heureux d’expliquer la garantie sur le système d’échappement des petits
moteurs hors--route de votre modèle 2000 et des années ultérieures (SORE). En Californie, les
nouveaux petits moteurs hors route doivent être conçus, construits et équipés pour rencontrer les
standards rigoureux d’antipollution. Ailleurs aux Etats--Unis, les nouveaux moteurs hors route à
bougie d’allumage certifiés pour les modèles de 1997 et plus, doivent rencontrer des normes simi-
laires mises de l’avant par le U.S. EPA. Briggs & Stratton garantit le système de contrôle d’échap-
pement de votre moteur pour la période de temps mentionnée ci--contre, sauf s’il a fait l’objet
d’abus, de négligence ou d’un entretien inapproprié.
Votresystème decontrôled’échappement comprend despièces telles quelecarburateur,le filtreà
air, le système d’ignition, le silencieux et le convertisseur catalytique. Il peut aussi comprendre les
connecteurs et autres pièces reliées à l’émission.
Lorsqu’ily acondition à garantie,B&Srépareragratuitementvotrepetit moteurhors--routeincluant
le diagnostic, les pièces et la main d’œuvre.
Couverture de garantie Briggs & Stratton contre toute défectuosité du système de contrôle d’échappement
Lespetits moteurshors routesont garantiscontreladéfectuositédespiècesdusystème decontrô-
led’échappementpourunepériodede2ans,sujetteaux conditionsstipuléesci--contre.Sin’impor-
te quelle pièce de votre moteur couverte par cette garantie est défectueuse, elle sera réparée ou
remplacée par B&S.
Responsabilités du propriétaire
Entant que propriétaire d’un petit moteur hors route, vous êtes responsable de veilleràl’exécution
de l’entretien requis t el que stipulé dans votre manuel d’opération et d’entretien. B&S vous recom-
mande de conserver tousles reçus couvrant les travaux d’entretien de votre petit moteur hors rou-
te, mais B&S ne peut refuser la garantie en raison d’absence de reçus ou pour défaut d’avoir suivi
tout l’échéancier du programme d’entretien.
Entant quepropriétaired’un petitmoteurhors route,vousdevez êtreinformé queB&Speutrefuser
d’honorercette garantiesi ladéfectuositéde votremoteurou d’unepartiedevotremoteurestdueà
un emploi abusif, une négligence, un entretien incorrect ou une modification non approuvée.
Vous avez la responsabilité d’apporter votre petit moteur hors route à un détaillant autorisé B&S
aussitôtquesurvient un problème. Les réparationssous garantie doivent être complétées dans un
délai raisonnable ne devant pas excéder 30 jours.
Si vous avez des questions relativement à votre garantie, vos droits et responsabilités, veuillez
communiquer avec un représentant de service B&S au numéro 1--414--259--5262.
La garantie du système d’échappement est une garantie contre les défectuosités.Les défectuosi-
tés sont jugées en fonction d’une utilisation normale du moteur. La garantie n’est pas reliée à un
test d’échappement effectué à l’intérieur.
Dispositions de la garantie du système d’échappement Briggs & Stratton
Ce qui suit concerne les dispositions spécifiques relativement à votre garantie sur le système de contrôle d’échappement. C’est une addition à la garantie B&S pour les moteurs non réglementés contenue
dans le manuel d’entretien et d’utilisation.
1. Pièces sous garantie
La couverture de cette garantie ne s’applique que sur les pièces listées ci--contre (les parties
dusystèmedecontrôled’échappement ) dans la mesure ces piècesétaientprésentessurle
moteur au moment de l’achat.
a. Système de dosage du carburant
Système d’enrichissement de démarrage à froid
Carburateur et parties internes
Pompeàessence
b. Système d’induction d’air
Filtre à air
Tubulure d’admission
c. Système d’ignition
Bougies d’allumage
Système d’allumage électromagnétique
d. Système catalyseur
Convertisseur catalytique
Collecteur d’échappement
Système d’injection d’air ou à pulsion
e. Autres pièces utilisées dans les systèmes ci--haut mentionnés
Soupapes et interrupteurs de dépression, de température, de position.
Connecteurs et assemblages.
2. Duréedelacouverture
B&S garantit le propriétaire initial et tous les acheteurs subséquents que les pièces sous ga-
rantiesontexemptesdevice dematièreoudefabricationquipourraientcauserdesdéfectuosi-
tés des pièces sous garantie pour une période de deux ans à partir de la date à laquelle le mo-
teur a été livré à l’acheteur.
3. Aucuns Frais
La réparation ou le remplacement de toute pièce sous garantie sera effectuée sans aucuns
frais pour le propriétaire, incluant les frais de main d’œuvre pour le diagnostic afin de détermi-
ner si la pièce sous garantie est défectueuse, conditionnel à ce que le diagnostic soit effectué
chezun détaillant autoriséB&S. Pourlagarantierelativeausystèmed’échappement,commu-
niquez avec le détaillant autorisé B&S le plus proche tel que listé dans les pages jaunes de
votre localité sous la rubrique moteur à essence, tondeuse ou autre catégorie similaire.
4. Réclamations et exclusions de la couverture.
Les réclamations de garantie doivent être complétées en accord avec les dispositions de la
politique de garantie B&S. La garantie ne couvre pas les défectuosités de pièces qui ne sont
pas des pièces d’origine B&S ou dans le cas d’abus, négligence oud’un entretien inapproprié.
La garantie B&S ne couvre pas les défectuosités de pièces sous garantie qui ont fait l’objet
d’ajouts, ont été modifiées ou de pièces qui ne sont pas des pièces B&S d’origine.
5. Entretien
Toute pièce sous garantie qui n’est pas remplacée au moment requis selon le manuel d’entre-
tien ou qui est planifiée seulement pour une inspection régulière sous la mention « réparer ou
remplacer si nécessaire » est garantie contre toute défectuosité pour la période de garantie.
Toute pièce sous garantie qui est planifiée pour un remplacement tel que requis dans l’entre-
tien est garantie contre toute défectuosité seulement pour la période de temps qui va jusqu’au
premier remplacement prévu pour cette pièce. Toute pièce de remplacement équivalente en
performance et durabilité peut être utilisée pour l’entretienou la réparation. Le propriétaire est
responsable de l’exécution de tout entretien requis tel que défini dans le manuel d’instruction
B&S sur l’entretien et la réparation.
6. Couverture indirecte
La couverture ci--contre s’étend à toute défectuosité des composantes du moteur causée par
ladéfectuositéde n’importe quelle pièce couverte par lagarantie et dont la garantie est encore
en vigueur.
Consultez les informations sur la période de durabilité d’émission et l’INDICE d’air sur l’étiquette d’émission de votre moteur
Les moteurs qui sont certifiés conformes aux normes standards d’émission du California Air Resources Board (CARB) Tier 2, doivent afficher l’information concernant la période de durabilité du système
d’émission et l’INDICE d’air. Cette information est indiquée sur les étiquettes apposées sur les moteurs par Briggs & Stratton. L’étiquette du moteur indiquera les renseignements concernant la certification.
Lapériodededurabilitéd’émissionindiquelenombred’heuresd’utilisationnormalepourlequellemoteurestcertifiéconformeauxnormesd’émissionsousréserved’unentretienappropriételqu’indiquédans
le manuel d’opération et d’entretien. Les catégories suivantes sont utilisées :
Modéré le moteur est certifié conforme pour 125 heures d’utilisation normale.
Intermédiaire le moteur est certifié conforme pour 250 heures d’utilisation normale.
Prolongé le moteur est certifié conforme pour 500 heures d’utilisation normale.
Parexemple, une tondeuse de modèle standardestutiliséeenviron 20 à 25 heuresparannée.Parconséquent, la période de durabilitéd’émission d’unmoteurdansla catégorieintermédiairepour ce typede
tondeuse équivaut à 10 à 12 ans.
L’indice d’air est un nombre qui décrit le niveau relatif d’émission pour une catégorie spécifique de moteur. Plus l’indice d’air est bas, plus le moteur est écologique. Cette information est indiquée sous une
forme graphique sur l’étiquette d’émission.
À compter du 1
er
juillet 2000, surveillez la p ériode de conformité d’émission sur les étiquettes
Après le 1
er
juillet 2000, certains moteurs B&S seront certifiés conformes aux normes environnementales d’émission standard du United States Environmental Protection Agency (US EPA) Phase 2. Pour les
moteurs certifiés pour la Phase 2, la période de conformité d’émission mentionnée sur les étiquettes indique le nombre d’heures d’utilisation pour lequel le moteur rencontre les normes fédérales. Pour les
moteurs de force moindre que 225 cc, la catégorie C = 125 heures, B = 250 heures et A = 500 heures. Pour les moteurs de 225 cc et plus, la catégorie C = 250 heures, B = 500 heures et A = 1000 heures.
Le remplacement du moteur portant le modèle de série 110000 est 190 cc, 120000 est 206 cc, 200000 est 305 cc, 210000 est 342 cc.
Ceci est une représentation des étiquettes d’émission
que vous retrouverez sur les moteurs certifiés :
CE MOTEUR EST CONFORME AUX NORMES
ANTIPOLLUTION 2000 -- 2001 DE CALIFORNIE
POUR LES PETITS MOTEURS HORS ROUTE ET
AUX NORMES ENVIRONNEMENTALES
AMÉRICAINES (EPA PHASE 2) POUR LES
PETITS MOTEURS HORS ROUTE. CONSULTEZ
LE MANUEL DU PROPRIÉTAIRE POUR LES
SPÉCIFICATIONS, L’ENTRETIEN ET LES
AJUSTEMENTS. CONFORME À LA RIODE
D’ÉMISSION EPA : CATÉGORIE : C
FAMILLE YBSXS.3192VA 274812
INFORMATIONS IMPORTANTES
CORPORATION BRIGGS & STRATTON
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Briggs & Stratton 110000/120000/200000/210000 Manuel utilisateur

Catégorie
Moteur
Taper
Manuel utilisateur