Philips AVENT SCD835/26 Le manuel du propriétaire

SCD831

SCD833

SCD835

SCD620

1

16

2

3

4

5

13

14

12

11

6

9 1087

17

18

19

25

21

20

22

24

23

15

English 6

Dansk 29

Deutsch 53

Español 78

Français 102

Italiano 126

Nederlands 150

Norsk 174

Português 197

Suomi 221

Svenska 244

Türkçe 268

ﺔﻴﺑﺮﻌﻟﺍ

291

English

Introduction

Congratulations on your purchase and welcome to Philips Avent! To fully

benefit from the support that Philips Avent offers, register your product at

www.philips.com/welcome.

The Philips Avent video babymonitor provides you with round-the-clock

support and it allows you to see your baby day and night from anywhere in

the house. The latest digital technology guarantees clear sound and the

clearest image of your baby. This gives you an additional sense of security

without entering your baby’s room and disturbing its sleep.

General description

1 Parent unit

2 Display

3 ECO light

4 Battery status light

5 Link light

6 Speaker

7 Control button (menu navigation/volume/brightness)

8 Sensitivity button

9 Lullaby button

10 Talk-back button

11 Socket for small plug

12 Mode button

13 On/off button

14 Antenna

15 Belt clip

16 Baby unit

17 Camera

18 Lullaby on/off button

19 On/off slide

20 Antenna

21 Speaker

22 Socket for small plug

23 Wall mounting holes

24 Adapter(2x)

25 Screws

Important safety information

Read this important information carefully before you use the appliance and

save it for future reference.

IMPORTANT

This baby monitor is intended as an aid. It is not a substitute for

responsible and proper adult supervision and should not be used as such.

Never leave your baby alone in your home. Always make sure there is

someone present to look after the baby and take care of its needs.

6

English

Disclaimer

Please note that you use this baby monitor at your own risk. Koninklijke

Philips N.V. and its subsidiary companies are not responsible for the

operation of this baby monitor or your use of it and therefore do not accept

any liability in connection with your use of this baby monitor.

Danger

-

Never immerse any part of the baby monitor in water or any other liquid.

Do not place the appliance where water or any other liquid can drip or

splash onto it. Never use the baby monitor in moist places or close to

water.

-

Never put any object on top of the baby monitor and do not cover it. Do

not block any ventilation openings. Install according to the

manufacturer’s instructions.

-

Cords present a potential strangulation hazard. Keep cords out of the

reach of children (more than 1 meter/3.5 feet away). Never place the baby

monitor inside the baby’s bed or playpen.

Warning

-

Check if the voltage indicated on the adapter corresponds to the local

mains voltage before you connect the appliance.

-

Do not modify or cut off any part of the adapter and its cord, as this

causes a hazardous situation.

-

Only use the adapter supplied.

-

If the adapter is damaged, always have it replaced with one of the

original type in order to avoid a hazard.

-

This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and understand

the hazards involved. Children shall not play with the appliance. Cleaning

and user maintenance shall not be made by children without supervision.

-

Protect the mains cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

appliance.

-

Make sure that you place the baby monitor in such a way that its cord

does not obstruct a doorway or passage. If you place the baby monitor

on a table or low cabinet, do not let the mains cord hang over the edge

of the table or cabinet. Make sure the cord does not lie on the floor

where it presents a tripping hazard.

-

Keep the packaging materials (plastic bags, cardboard buffers, etc.) out of

the reach of children, as they are not a toy.

-

To prevent electric shock, do not open the housing of the baby unit or

parent unit.

Caution

-

Use the appliance at a temperature between 0°C (32°F) and 40°C (104°F).

-

Do not install the appliance near any heat sources such as radiators, heat

registers, stoves or other apparatus (including amplifiers) that produce

heat.

7

English

-

Make sure that your hands are dry when you handle adapters, plugs and

the mains cord.

-

All required markings on the baby unit, parent unitand power adapter

are located on the bottom of the baby unit, parent unit and power

adapter.

Compliance with standards

-

This product complies with the radio interference requirements of the

European Community.

-

Philips Consumer Lifestyle hereby declares that this baby monitor is in

compliance with the essential requirements and other relevant provisions

of Directive 2014/53/EU (FHSS: frequency band 2.4GHz, maximum radio-

frequency power: 100 mW EIRP). A copy of the EC Declaration of

Conformity (DoC) is available online at www.philips.com/support.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic fields.

Preparing for use

Baby unit

Put the power adapter in the baby unit and the adapter in the wall socket.

Parent unit

The parent unit runs ona built-in rechargeable Li-ion battery.

Follow the below steps to charge the parent unit:

1 Put the power adapter in the parent unit and put the adapter in the wall

socket.

-

The battery status light turns orange to indicate that the appliance is

charging.

8

English

20°CEco

1

-

When the battery is fully charged, thebattery statusindicator lights up

green continuously.

10 hrs=3 hrs

-

When you charge the parent unit for 3 hours, it can be used cordlessly for

approx. 10 hours.

-

If the parent unit is switched on during charging, charging takes

approximately twice as long.

20°CEco

1

-

When the rechargeable battery of the parent unit is almost empty, the

battery status light turnsred and the parent unit beeps.

-

If the battery is completely empty and the parent unit it not connected to

the mains, the parent unit automatically switches off and loses contact

with the baby unit.

Note: The built in rechargeable battery cannot be removed from the

product.

Note: The battery gradually and very slowly discharges, even when the

parent unit is switched off.

Tip: To save battery, switch off the parent unit when you do not use it.

Note: We advise you to keep the parent unit connected to the mains during

the whole night. If the battery of the parent unit runs low during the night,

the parent unit beeps and this may wake you up.

Using the baby monitor

Linking parent unit and baby unit

1 Push the on/off slide on the baby unit upwards to the ON position.

9

English

2 When the baby unit is on, the power-on light on the baby unit lights up

green.

Note: The power-on light on the baby unit always lights up green, even

when there is no connection with the parent unit.

>2.5m/8.2ft

3 Make sure that the parent unit and the baby unit are at least 2.5 meters/

8.2 feet away from each otherto avoid acoustic feedback.

4 Press the on/off button on the parent unit to switch on the parent unit.

20°CEco

1

-

The display goes on, the linking image appears on the display and the

link light lights up red. The parent unit starts to search for the baby

unit.

20°CEco

1

-

When the parent unit and baby unit are linked, the link light lights up

green on the parent unit and one or more bars appear on the display.

10

English

20°CEco

1

Note: It takes less than 10 seconds to establish the link between the

parent unit and the baby unit.

When thebaby unit is turned off, the parent unit will show the out of

range image. Make sure that the baby unit is switched on.

-

If no connection has been established, the link light turns red, the

parent unit beeps three short beeps every 20 seconds and the out-of-

range image appears on the display.

Positioning the baby monitor

Warning: The cord of the baby unit presents a

potential strangulation hazard. Make sure that

the baby unit and its cord are at least 1 meter /

3.5 feet away from your baby. Never place the

baby monitor inside the baby’s bed or playpen.

>1-1.5m/3.5-5ft

1 For optimal sound detection, make sure that the baby unit is no further

than 1.5 meter/ 5 feet away from the baby. Make sure that the baby unit

is at least 1 meter/ 3.5 feet away from the baby because of potential

strangulation hazard.

>2.5m/8.2ft

2 Place the parent unit within the operating range of the baby unit. Make

sure it is at least 2.5 meters / 8.2 feet away from the baby unit to avoid

acoustic feedback.

Note: If you use a cordless phone, wireless video, Wi-Fi network,

microwave oven or Bluetooth on 2.4GHz and you experience interference

on either the parent unit or baby unit, move the parent unit until there is

no more interference.I

3 There are two ways to position the baby unit

a Place the baby unit on a stable, level and horizontal surface.

b Mount the baby unit to the wall with the screws supplied.

11

English

Tip: The wall mount template (see 'Wall mount') to mount the baby unit

to the wall can be found at the end of this user manual.

Tip: Use the provided template to mark the exact location of the screw

holes on the wall.

Tip: Position the baby unit at a higher level to get a good overview of the

baby’s bed or playpen.

4 Adjust the baby unit in a way that ensures the best visibility of your baby.

The baby unit can be rotated to position it in the desired way.

Operating range

<300m/985ft

<50m/165ft

The operating range is up to 50 meters/ 165 feet indoors and 300

meters/985 feet outdoors. The operating range of the baby monitor varies

depending on the surroundings and factors that cause interference. Wet

and moist materials cause so much interference that the range loss is up to

100%.

Dry materials Material

thickness

Loss of range

Wood, plaster, cardboard, glass (without metal,

wires or lead)

< 30cm (12in) 0-10%

Brick, plywood < 30cm (12in) 5-35%

Reinforced concrete < 30cm (12in) 30-100%

Metal grilles or bars < 1cm (0.4in) 90-100%

Metal or aluminium sheets < 1cm (0.4in) 100%

Features and settings

Volume

You can adjust the speaker volume of the parent unit to the level you prefer.

12

English

1 Press the top or bottom part of the control button to adjust the volume.

20°C

1

Tip: Make sure that the volume is adapted to the current conditions.

Under noisy conditions, the vibration alert can be turned on as well.

The volume bar appears on the display to show the selected volume.

Note: If the volume is set to a high level, the parent unit consumes more

power.

Note: When the volume bar is at its minimum, the volume is muted. The

parent unit shows a mute icon in the status bar and you will only receive

alerts and video from the parent unit.

Brightness

You can adjust the display brightness of the parent unit to the level you

prefer.

1 Press the left or right part of the control button to adjust the brightness

of the display of the parent unit.

20°C

1

The brightness bar appears on the display to show the selected display

brightness.

Note: If the brightness is set to a high level, the parent unit consumes more

power.

Modes

This baby monitor has four different modes that allows you to choose how

you want to look after your baby: VIDEO, AUDIO, VOX and ECO.

13

English

With the baby monitor on, you can switch between these 4 different modes

by pressing the mode button on the side of the parent unit.

The display shows the selected mode. The selected mode is also indicated

in the status bar. When turning on the device, the mode that was last used

will be active.

VIDEO mode

VIDEO

Press the mode button on the side of the parent unit to select theVIDEO

mode.

20°C

1

VIDEO

When the VIDEO mode is activated, the screen is always on, so you can see

your baby. All sounds are directly transmitted to the parent unit.

20°C

1

VIDEO

Note: Set the sensitivity level to 'very high' to have continuous sound on the

parent unit. Please see the Sensitivity level chapter for more information.

AUDIO mode

AUDIO

1 Press the mode button on the side of the parent unit to switch to AUDIO

mode.

14

English

20°C

1

AUDIO

When the AUDIO mode is activated, the display of the parent unit switches

off. After 3 seconds the display will completely turn off and the status bar

will disappear.

Note: The status bar is not visible when the display is off.

20°C

1

VOX

Note: The link light shows that the parent unit is still on and connected to

the baby unit.

Note: Set the sensitivity level to 'very high' to have continuous sound on the

parent unit. Please see the Sensitivity level chapter for more information.

All sounds are constantly transmitted to the parent unit. If your baby cries,

the display of the parent unit is still off, but the sounds detected by

thebaby unitare transmitted to the parent unit.

VOX mode

VOX

1 Press the mode button on the side of the parent unit to switch to VOX

mode.

Note: When the display is on, the selected mode is shown in the status bar.

The status baris not visible when the display is off.

20°C

1

AUDIO

When the VOX mode is activated, the display and sound of the parent unit

switch off, if there is no sound detected for 20 seconds.

20°C

1

ECO

Whensound is picked up by the baby unit, the displayand sound of the

parent unit switch on immediately.The sounds are transmitted to the parent

unit.

Note: The minimum sound level to activate sound and display is defined by

the sensitivity setting.

15

English

ECO mode

ECO

1 Press the mode button on the side of the parent unit to switch to ECO

mode.

Note: When the display is on, the selected mode will be visible in the status

bar. The status bar is not visible when the display is off.

20°C

1

ECO

When the ECO mode is activated the display and sound of the parent unit

switch off when no sound is detected for 20 seconds. TheECO light lights up

green to indicate that the ECO mode is activated. During ECO mode the

display and sound transmissions are turned off.

20°C

1

ECO

Whensound is picked up by the baby unit, the displayand sound of the

parent unit switch on immediately.The sounds are transmitted to the parent

unit.

Note: The minimum sound level to activate sound and display is defined by

the sensitivity setting.

Lullabies

You can activate the lullaby feature either from the parent unit or from the

baby unit.

To activate the lullaby feature from the parent unit, follow the instructions

below:

Lullaby selection

1 Press the lullaby button on the parent unit to open the menu for

lullabies.

Note: Pressing the lullaby button while the lullaby menu is already open,

will close the menu.

16

English

2 Press the right part of the control button to enter the list of lullabies.

Lullaby Songs

1 Rock-a-Bye Baby

2 Twinkle, Twinkle

3 Hush, Little Baby

4 Brahm’s Lullaby

5 Golden Slumbers

3 Press the top or bottom part of the control button to scroll through the

list of lullabies.

Lullaby Songs

1 Rock-a-Bye Baby

2 Twinkle, Twinkle

3 Hush, Little Baby

4 Brahm’s Lullaby

5 Golden Slumbers

4 Press the right part of the control button to play a specific lullaby.

If you want to pause the lullaby, press the right side of the control button

again.

5 The status barof the parent unit shows the number of lullabies thatare

being played and repeated.

15 min

The lullaby starts to play on the baby unit and it is repeated continuously

for approximately 15 minutes.

Tip: To repeat all songs that are available, select the last option in the list.

Lullaby Songs

1 Rock-a-Bye Baby

2 Twinkle, Twinkle

3 Hush, Little Baby

4 Brahm’s Lullaby

5 Golden Slumbers

6 To select another lullaby, scroll up or down with thecontrol button to

select another song from the list.Press the right part of the control

button to start the selected song.

7 To stop the lullaby, press the lullaby button on the parent unit and pause

the song that is currently playing by pressing the right part of the control

button one more time.

17

English

Lullaby volume

1 Press the lullaby button on the parent unit to open the menu for

lullabies. Press the left part of the control button and then press the

bottom of the control button to select the volume options of thelullaby

menu. Press the right part of the control button to access the lullaby

volume levels.

20°C

1

2 Press the top or bottom part of the control button to adjust the volume.

3 To stop the lullaby, press the lullaby button on the parent unit and pause

the song that is currently playing by pressing the right part of the control

button one more time.

To activate the lullaby feature from the baby unit, press the lullaby on/off

button on the baby unit.

15 min

The latest lullaby selected on the parent unit starts to play on the baby unit

and is repeated continuously for approximately 15 minutes.

To stop the lullaby on the baby unit, press the lullaby on/off button on the

baby unit.

Talk-back

You can use the talk-back button on the parent unit to talk to your baby.

18

English

1 Press and hold the talk-back button on the parent unit.

2 Talk clearly into the microphoneat the front of the parent unit from a

distance between 15-30cm /0.5-1ft.

As long as the talk-back button is pressed, there is an open sound

connection to the baby unit. The display of the parent unit shows the

talk-back icon, indicating the active connection.

3 Release the talk-back button when you have finished talking.

Note: As long as the talk-back button is pressed, theparent unitcannot

process sounds coming from the baby unit.

Sensitivity

The sensitivity level of the baby unit defines what you hear through the

parent unit. When the level is set high, you will hear many sounds, including

soft background sounds. When the sensitivity level is set low, you will hear

only the louder sounds.

1 Press the sensitivity button to access the sensitivity levels.

Note: When pressing the sensitivity button again, you will leave the menu.

20°C

1

2 Press the top or bottom part of the control button to select the desired

sensitivity level.

19

English

20°C

1

If your baby only makes soft sounds, the sensitivity of the baby unit needs

to be set to a high sensitivitylevel on the parent unit.

20°C

1

The louder your baby sounds, the lower the sensitivity can be set on the

parent unit.

Note: In AUDIO and VIDEO mode, you will have continuous sound when the

sensitivity level is on 'very high'. Otherwise, low sounds will be muted.

Tip: The sensitivity level can be adjusted so you will always hear your baby

without the disruption of other sounds. When there is a lot of background

noise, turn the sensitivity lower so you will not hear these sounds through

the parent unit.

Belt clip

You can take the parent unit with you inside and outside the house by

attaching the parent unit to your belt or waistband with the belt clip. This

allows you to monitor your baby while you are moving around.

Note: The display is now turned upside down, which allows you to see your

baby on the screen by simply lifting up the parent unit.

Cleaning and maintenance

Warning: Do not immerse the parent unit, baby

unit and power adapters in water and do not

clean them under the tap.

20

English

La page est en cours de chargement...

Philips AVENT SCD835/26 Le manuel du propriétaire

Philips AVENT SCD835/26 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents