Avent SCD630/37 Manuel utilisateur

SCD843

SCD630

1

2

3

4

5

6

15

16

14

13

7

10 11 1298

19

18

20

21

22

25

23

27

26

28

31

30

17

29

24

English 6

Español 33

Français (Canada) 59

Português 87

English

Introduction

Congratulations on your purchase and welcome to Philips Avent! To fully

benefit from the support that Philips Avent offers, register your product at

www.philips.com/welcome.

The Philips Avent video babymonitor provides you with round-the-clock

support and it allows you to see your baby day and night from anywhere in

the house. The latest digital technology guarantees clear sound and the

clearest image of your baby. This gives you an additional sense of security

without entering your baby’s room and disturbing its sleep.

Know these safety symbols

This “bolt of lightning” indicates uninsulated material within your unit may

cause an electrical shock. For the safety of everyone in your household,

please do not remove product covering.

The exclamation mark calls attention to features that require you to read the

enclosed user information closely to prevent operating and maintenance

problems.

Warning: To reduce the risk of fire or electric shock, this appliance

should not be exposed to rain or moisture and objects filled with

liquids, such as vases, should not be placed on this appliance.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this appliance near water.

6 Do not use the product while you are in a bathtub, shower or pool.

Immersion of the product in water could cause an electrical shock.

7 Clean only with dry cloth.

8 Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

9 Do not install near any heat sources such as radiators, heat registers,

stoves or other appliance (including amplifiers) that produce heat.

10 Installed batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

6

English

11 Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

appliance.

12 Only use attachments/accessories specified by the manufacturer.

13 Use this appliance only for its intended use as described in this manual.

14 Unplug this product from the wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners.

15 Unplug this appliance during lightning or when unused for long periods

of time.

16 Unplug the product immediately and do not use it if the adapter, the cord

or the product itself is damaged.

17 Refer all servicing to qualified service personnel. Servicing is required

when the appliance has been damaged in any way, such as power supply

cord or plug is damaged, liquid has been spilled or objects have fallen

into the appliance, the appliance has been exposed to rain or moisture,

does not operate normally, or has been dropped. Please check the

power cord periodically to prevent potential damages, such as worn or

cut cord. For assistance, visit our website www.philips.com/ support or

contact the Philips Consumer Care Center in your country.You find its

contact details in the worldwide guarantee leaflet.

18 Keep screws and small items out of the reach of the baby.

19 All the required markings are located on the bottom of the appliance and

on the adapter.

WARNING: STRANGULATION HAZARD. Children have

STRANGLED in cords. Keep this cord out of the reach of children

(more than 3.5 feet (1 meter) away). Do not remove the tag.

Caution

Caution: Prevent risk of explosion, electric shock, short circuit, or leakage.

-

The appliance shall not be exposed to dripping or splashing and no

objects filled with liquids, such as vases, shall be placed on the appliance.

-

To prevent electric shock, do not open the housing of the product.

-

Where the power plug is used as the disconnect appliance, the

disconnect appliance shall remain readily operable.

-

The adapter contains a transformer. Do not cut off the adapter to replace

it with another plug, as this causes a hazardous situation.

-

Use the supplied adapter to connect the appliance to the power outlet.

-

If the adapter is damaged, always have it replaced with one of the

original type in order to avoid a hazard.

7

English

Adult supervision

-

This baby monitor is intended as an aid. It is not a substitute for

responsible and proper adult supervision and should not be used as

such.

-

Never place the baby monitor inside or directly over the baby bed or

playpen.

-

To prevent overheating, do not cover the baby monitor with a towel,

blanket or any other items.

-

For their safety, do not allow children to touch and play with the baby

monitor, the adapter and the accessories. THIS IS NOT A TOY.

General description

1 Parent unit

2 Sound level lights

3 Display

4 ECO light

5 Battery status light

6 Link light

7 Speaker

8 Control button (menu navigation/volume/brightness)

9 Menu button

10 Lullaby button

11 Talk-back button

12 Microphone

13 Socket for power adapter

14 Mode button

15 On/off button

16 Antenna

17 Belt clip

18 Baby unit

19 Camera

20 Power on light

21 Lullaby on/off button

22 Nightlight

23 Microphone

24 Nightlight on/off button

25 On/off slide

26 Antenna

27 Speaker

28 Socket for small plug

29 Temperature sensor

30 Wall mounting holes

31 Adapter(2x)

8

English

Preparing for use

Baby unit

Put the power adapter in the baby unit and the adapter in the wall socket.

Parent unit

The parent unit runs ona built-in rechargeable Li-ion battery.

Follow the below steps to charge the parent unit:

1 Put the power adapter in the parent unit and put the adapter in the wall

socket.

-

The battery status light turns orange to indicate that the appliance is

charging.

20°CEco

1

-

When the battery is fully charged, the battery status light turns green

continuously.

10 hrs=3 hrs

-

When you charge the parent unit for 3 hours, it can be used cordlessly for

approx. 10 hours.

-

If the parent unit is switched on during charging, charging takes

approximately twice as long.

9

English

20°CEco

1

-

When the rechargeable battery of the parent unit is almost empty, the

battery status light turnsred and the parent unit beeps.

-

If the battery is completely empty and the parent unit it not connected to

the mains, the parent unit automatically switches off and loses contact

with the baby unit.

Note: The built in rechargeable battery cannot be removed from the

product.

Note: The battery gradually and very slowly discharges, even when the

parent unit is switched off.

Tip: To save battery, switch off the parent unit when you do not use it.

Note: We advise you to keep the parent unit connected to the mains during

the whole night. If the battery of the parent unit runs low during the night,

the parent unit beeps and this may wake you up.

Using the baby monitor

Linking parent unit and baby unit

1 Push the on/off slide on the baby unit upwards to the ON position.

2 When the baby unit is on, the power-on light on the baby unit lights up

green.

Note: The power-on light on the baby unit always lights up green, even

when there is no connection with the parent unit.

>2.5m/8.2ft

3 Make sure that the parent unit and the baby unit are at least 2.5 meters/

8.2 feet away from each otherto avoid acoustic feedback.

10

English

4 Press the on/off button on the parent unit to switch on the parent unit.

20°CEco

1

-

The display goes on, the linking image appears on the display and the

link light lights up red. The parent unit starts to search for the baby unit.

20°CEco

1

-

When the parent unit and baby unit are linked, the link light lights up

green on the parent unit and one or more bars appear on the display.

20°CEco

1

Note: It takes less than 10 seconds to establish the link between the

parent unit and the baby unit.

-

When thebaby unit is turned off, the parent unit will show the out of

range image. Make sure that the baby unit is switched on.

-

If no connection has been established, the link light turns red, the parent

unit beeps three short beeps every 20 seconds and the out-of-range

image appears on the display.

Positioning the baby monitor

Warning: The cord of the baby unit presents a potential

strangulation hazard. Make sure that the baby unit and its cord

are at least 1 meter / 3.5 feet away from your baby. Never place

the baby monitor inside the baby’s bed or playpen.

11

English

>

1-1.5m/3.5-5ft

1 For optimal sound detection, make sure that the baby unit is no further

than 1.5 meter/ 5 feet away from the baby. Make sure that the baby unit

is at least 1 meter/ 3.5 feet away from the baby because of potential

strangulation hazard.

>2.5m/8.2ft

2 Place the parent unit within the operating range of the baby unit. Make

sure it is at least 2.5 meters / 8.2 feet away from the baby unit to avoid

acoustic feedback.

Note: If you use a cordless phone, wireless video, Wi-Fi network,

microwave oven or Bluetooth on 2.4GHz and you experience

interference on either the parent unit or baby unit, move the parent unit

until there is no more interference.

3 There are two ways to position the baby unit:

a Place the baby unit on a stable, level and horizontal surface.

b Mount the baby unit to the wall with screws.

Tip: The wall mount template (see 'Wall mount') to mount the baby unit

to the wall can be found at the end of this user manual.

Tip: Use the provided template to mark the exact location of the screw

holes on the wall.

Tip: Position the baby unit at a higher level to get a good overview of the

baby’s bed or playpen.

Adjust the baby unit in a way that ensures the best visibility of your baby.

The baby unit can be rotated to position it in the desired way.

12

English

Operating range

<50m/165ft

<300m/985ft

The operating range is up to 50 meters/ 165 feet indoors and 300

meters/985 feet outdoors. The operating range of the baby monitor varies

depending on the surroundings and factors that cause interference. Wet

and moist materials cause so much interference that the range loss is up to

100%.

Dry materials Material thickness Loss of range

Wood, plaster, cardboard, glass (without metal,

wires or lead)

< 30cm (12in) 0-10%

Brick, plywood < 30cm (12in) 5-35%

Reinforced concrete < 30cm (12in) 30-100%

Metal grilles or bars < 1cm (0.4in) 90-100%

Metal or aluminium sheets < 1cm (0.4in) 100%

Features and settings

Volume

You can adjust the speaker volume of the parent unit to the level you prefer.

1 Press the top or bottom part of the control button to adjust the volume.

20°C

1

Tip: Make sure that the volume is adapted to the current conditions.

Under noisy conditions, the vibration alert can be turned on as well.

The volume bar appears on the display to show the selected volume.

Note: If the volume is set to a high level, the parent unit consumes more

power.

Note: When the volume bar is at its minimum, the volume is muted. The

parent unit shows a mute icon in the status bar and you will only receive

alerts and video from the parent unit.

13

English

Brightness

You can adjust the display brightness of the parent unit to the level you

prefer.

1 Press the left or right part of the control button to adjust the brightness

of the display of the parent unit.

20°C

1

The brightness bar appears on the display to show the selected display

brightness.

Note: If the brightness is set to a high level, the parent unit consumes more

power.

Sound level lights

The parent unit continuously monitors the sound level in your baby’s room,

and the sound level lights on the parent unit let you know if there is any

sound picked up in the baby room.

20°C

1

VIDEO

As long as no sound is detected, the sound level lights are out.

20°C

1

VIDEO

When the baby unit picks up a sound, one or more sound level lights on the

parent unit light up green. The number of lights that go on depends on the

loudness of the sound picked up by the baby unit. The louder your baby

cries, more sound level lights light up green.

14

English

Modes

This baby monitor has four different modes that allows you to choose how

you want to look after your baby: VIDEO, AUDIO, VOX and ECO.

With the baby monitor on, you can switch between these 4 different modes

by pressing the mode button on the side of the parent unit.

The display shows the selected mode. The selected mode is also indicated

in the status bar. When turning on the device, the mode that was last used

will be active.

VIDEO mode

VID

EO

VIDEO

Press the mode button on the side of the parent unit to select theVIDEO

mode.

20°C

1

VIDEO

When the VIDEO mode is activated, the screen is always on, so you can see

your baby. All sounds are directly transmitted to the parent unit.

Note: Set the sensitivity level to 'very high' to have continuous sound on the

parent unit. Please see the Sensitivity level chapter for more information.

20°C

1

VOX

If your baby cries, the sound level lights light up green. As long as no sound

is detected, the sound level lights are off.

15

English

AUDIO mode

AUDI

O

AUDIO

1 Press the mode button on the side of the parent unit to switch to AUDIO

mode.

VOXAUDIO

When the AUDIO mode is activated, the display of the parent unit switches

off. After 3 seconds the display will completely turn off and the status bar

will disappear.

Note: The status bar is not visible when the display is off.

20°C

1

AUDIO

Note: The link light shows that the parent unit is still on and connected to

the baby unit.

Note: When sensitivity level is not set to 'very high', low sounds will be

muted.

Note: Set the sensitivity level to 'very high' to have continuous sound on the

parent unit. Please see the Sensitivity level chapter for more information.

All sounds are constantly transmitted to the parent unit. If your baby cries,

the display of the parent unit is still off, but the sound level lights light up

green and the sounds detected by thebaby unitare transmitted to the

parent unit. As long as no sound is detected, the sound level lights are off.

VOX mode

VOX

1 Press the mode button on the side of the parent unit to switch to VOX

mode.

Note: When the display is on, the selected mode is shown in the status bar.

The status baris not visible when the display is off.

VOX

20°C

1

VOX

When the VOX mode is activated, the display and sound of the parent unit

switch off, if there is no sound detected for 20 seconds.

16

English

20°C

1

VOX

Whensound is picked up by the baby unit, the displayand sound of the

parent unit switch on immediately.The sounds are transmitted to the parent

unit and the sound level lights light up green. As long as no sound is

detected, the sound level lights are off.

Note: The minimum sound level to activate sound and display is defined by

the sensitivity setting.

ECO mode

ECO

1 Press the mode button on the side of the parent unit to switch to ECO

mode.

Note: When the display is on, the selected mode will be visible in the

status bar. The status bar is not visible when the display is off.

ECO

When the ECO mode is activated the display and sound of the parent unit

switch off when no sound is detected for 20 seconds. TheECO light lights up

green to indicate that the ECO mode is activated. During ECO mode the

display and sound transmissions are turned off.

20°C

1

ECO

Whensound is picked up by the baby unit, the displayand sound of the

parent unit switch on immediately.The sounds are transmitted to the parent

unit and the sound level lights light up green. As long as no sound is

detected, the sound level lights are off.

Note: The minimum sound level to activate sound and display is defined by

the sensitivity setting.

Nightlight

1 Press the nightlight on/off button on the baby unit to switch on the

nightlight feature.

17

English

The nightlight of the baby unit goes on.

Note: It is not possible to control the nightlight from the parent unit. You

can only switch the nightlight on or off on the baby unit.

2 Press the nightlight on/off button again to switch off the nightlight.

Lullabies

You can activate the lullaby feature either from the parent unit or from the

baby unit.

To activate the lullaby feature from the parent unit, follow the instructions

below:

Talk-back

You can use the talk-back button on the parent unit to talk to your baby.

1 Press and hold the talk-back button on the parent unit.

2 Talk clearly into the microphoneat the front of the parent unit from a

distance between 15-30cm /0.5-1ft.

As long as the talk-back button is pressed, there is an open sound

connection to the baby unit. The display of the parent unit shows the

talk-back icon, indicating the active connection.

3 Release the talk-back button when you have finished talking..

Note: As long as the talk-back button is pressed, theparent unitcannot

process sounds coming from the baby unit.

18

English

Menu features

All features described in the following sections can be operated through the

menu of the parent unit.

1 Press the menu button to enter the menu.

Note: When pressing the menu button again, you will leave the menu.

2 Use the control button to navigate through the menu. The selected menu

item is highlighted purple.

Note: If you are already in one of the sub menus and you want to switch

between menu features,press the left part of the control button to

navigate back to the main menu.

3 Press the top or bottom part of the control button to scroll through the

different menu items.

When you are navigating through the menu features and do not want to

save any change, press the menu button. You will leave the menu

without changing any settings.

Note: If you are in the menu but do not press a button for 5 seconds, the

menu will exit without saving changed settings.

Zoom

20°CVIDEO

1

Zoom

O

On

1 Press the right part of the control button toenter the zoom menu.

19

English

Zoom

Oﬀ

On Pan

20°CVIDEO

1

2 Press the bottom part of the control button to switch on the zoom

feature.

20°CVIDEO

Menu

1

3 To adjust the video image press the right part of the control button. Now

you can use the top/bottom/right/left part of the control button to

choose what image will be shown on the parent unit.

4 Press the menu button to save the new setting. The image is

automatically saved after 5 seconds.

5 Go to the zoom menu and turn off the zoom function, if you want to

zoom out the image on the parent unit.

Sensitivity

The sensitivity level of the baby unit defines what you hear through the

parent unit. When the level is set high, you will hear many sounds, including

soft background sounds. When the sensitivity level is set low, you will hear

only the louder sounds.

20°C

1

VIDEO

Sensitivity

Low

Medium

High

Very High

1 Press the right part of the control button to access the sensitivity levels.

Note: When pressing the left part of the control button again, you will

leave the menu.

20°C

1

Sensitivity

Low

Medium

High

Very High

VIDEO

2 Press the top or bottom part of the control button to select the desired

sensitivity level.

20°C

1

20°C

1

VIDEO

Sensitivity

Low

Medium

High

Very High

If your baby only makes soft sounds, the sensitivity of the baby unit

needs to be set to a high sensitivitylevel on the parent unit.

20

English

La page charge ...

Avent SCD630/37 Manuel utilisateur

Avent SCD630/37 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents