Intermec ScanPlus 1802 Manuel utilisateur

Taper
Manuel utilisateur
ScanPlus 1802
Cordless System
Operator's Guide
32
WARNING: Fire, explosion and severe burn hazard. Do not crush, disassemble, heat above 100° C (212° F) or
incinerate Battery Pack (P/N 3-360029-03).
ScanPlus 1802 SR
ScanPlus 1802 ST
Range
Low battery
"beep beep beep beep beep beep"
"beep"
25 m (80 ft)
Operation
"beep"
Reading distance
ScanPlus 1802 SR
ScanPlus 1802 ST
1 cm - 7 cm
(0.4" - 2.8")
2 cm - 29 cm
(0.8" - 11.4")
1 cm - 7 cm
(0.4" - 2.8")
2 cm - 29 cm
(0.8" - 11.4")
54
Regulatory statements
Intermec hereby declares that the ScanPlus 1802 Cordless System has been tested and found compliant with the below listed
standards as required by the EMC Directive 89/336/EEC as amended by 92/31/EEC and by the Low Voltage Directive 73/23/EEC
as amended by 93/68/EEC: ETS 300 683 (1997), EN 300 220-1 (1999), EN60950 (1993) Safety of information technology equipment.
This device is TÜV GS licensed (EN 60950 and EN 60825-1) for safety only when powered by an external Intermec power supply. The
original Declaration of Conformity is available on demand. The ScanPlus 1802 Cordless System is certified for use in all countries belonging
to the European Union.
USA & Canada: This device complies with Part 15 of the FCC rules and RSS-210 of Industry Canada. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to
which the receiver is connected or consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with the FCC Rules, the I/O cables that interconnect between the device and any peripheral must be as specified
by Intermec.
Caution: Changes or modifications not expressly approved by Intermec could void the user's authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This device requires a
radio license unless it is used totally inside a building (the user must obtain this license).
This device is UL and cUL listed (UL1950 / C22.2 n°950).
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Cet appareil exige une
license radio à moins d'être entièrement installé dans un batiment (l'utilisateur doit obtenir cette license).
Cet équipement est conforme aux exigences de CNR-210 de Industrie Canada. L'utilisation de ce dispositif est autorisée aux conditions suivantes:
(1) Il ne doit pas produire de brouillage, et (2) l'utilisateur de l'équipement doit accepter tout brouillage reçu, même si ce brouillage est susceptible
de compromettre son fonctionnement.
Cet équipement est listé UL et cUL (UL1950 / C22.2 n°950).
Australia-New Zealand: This equipment has been tested and found to conform to the Australian EMC framework concerning
Class B digital devices, prescribed by the Australian and New-Zealander standard AS/NZS 3548.
The information contained in this document is for informational purposes only and is subject to change without notice. No part of this document
may be copied or reproduced in any manner without the prior written permission of Intermec Technologies Corporation.
ScanPlus/MicroBar products are covered by patents issued or pending in the USA and other countries.
The word Intermec, the Intermec logo, ScanPlus, MicroBar and EasySet are either trademarks or registered trademarks of Intermec.
Throughout this document, trademarked names may be used. Rather than put a trademark (™ or ®) symbol in every occurrence of a trademarked
name, we state that we are using the names only in an editorial fashion, and to the benefit of the trademark owner, with no intention of infringement.
Class 1 LED product - safe when used in any reasonable operating conditions (ScanPlus 1802 SR only).
North America / Asia Pacific / Latin America • 6001 36th Avenue West, PO Box 4280, Everett, WA 98203-9280
Tel: +1 425 348 2600 • Fax: +1 425 348 2833 • U.S. service and technical support, tel: 1 800 755 5505 • Canadian service and technical support,
tel: 1 800 668 7043
Europe / Middle East / Africa • Sovereign House, Vastern Road, Reading RG1 8BT, England
Tel: +44 118 987 9420 • Fax: +44 118 987 9416
Internet: http://www.intermec.com
Technical Information: http://datacapture.intermec.com
© 2002 Intermec Technologies Corporation.
Revision level 3-362049-00-012
All Rights Reserved.
N309
Laser warnings (ScanPlus 1802 ST only)
Fix these warning labels onto the product if they
are not already present.
Collez les étiquettes d’avertissement sur votre
produit.
Bringen Sie Warnetiketten auf dem Produkt an.
Fije la etiqueta de advertencia en el producto.
Un’etichetta di avviso per il laser è da applicare
sul prodotto.
Cole as etiquetas de precaução no equipamento.
CAUTION – Use of controls or adjustments or performance of procedures other than those specified herein result in
hazardous laser light.
VORSICHT – Bei einer anders als hier beschriebenen Verwendung der Bedienelemente oder Veränderungen oder
einer anderen Ausführung der Arbeitsabläufe entsteht gefährliches Laserlicht.
ATTENTION – L’utilisation de contrôles/commandes ou de réglages ou l’exécution de procédures autres que ceux
précisés par le présent document provoquent une lumière laser dangereuse.
The ScanPlus 1802 ST is a Class 2 laser scanner and complies with the following safety standards:
USA: CDRH - Class II Laser Product (CFR 21 Subpart J)
IEC 825-1 EN 60825-1 - Class 2 Laser Product.
These warnings do not apply to the ScanPlus 1802 SR which is a CCD scanner and does not contain a laser.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Intermec ScanPlus 1802 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues