Intermec MaxiScan 2210 Manuel utilisateur
- Taper
- Manuel utilisateur
P/N 3-420049-00
Operator’s Guide
MaxiScan 2210
Presentation Scanner
Bedieneranleitung
Guia do Utilizador
Guide de l'Opérateur
Guida dell'operatore
Guía del Usuario
32
"beep"
(8")
➊➋➌
Operation
Reading distance
typical average reading distance
Maintenance
Replace a scratched or damaged window to improve reading.
English USA DHHS Standard 21CFR 1040.10 and 1040.11: Class IIa Laser Product
IEC 825-1 (1993) EN 60825-1 (1997): Class 1 Laser Product
Avoid long term viewing of direct laser light.
Caution: laser light when open. Do not stare into beam.
Deutsch IEC 825-1 (1993) EN 60825-1 (1997): Laser-Produkt der Klasse 1
Augen vor direktem Laserlicht schützen.
Vorsicht! Laserlicht bei geöffnetem Gehäuse. Nicht in den Strahl starren.
Español IEC 825-1 (1993) EN 60825-1 (1997): Aparato láser de Clase 1
Evitar exposiciones prolongadas de la vista a la radiación láser directa.
Cuidado: radiación láser; en funcionamiento no mirar dentro del rayo láser.
Français IEC 825-1 (1993) EN 60825-1 (1997): Appareil Laser de Classe 1
Eviter toute exposition prolongée de la vue au rayonnement laser direct.
Attention: rayonnement laser; en cas d’ouverture, ne pas regarder dans le faisceau.
Italiano IEC 825-1 (1993) EN 60825-1 (1997): Apparecchio Laser Classe 1
Non esporre a lungo la vista ad un irradiamento laser diretto.
Attenzione: irradiamento laser; ad apparecchio in funzione, non guardare il fascio
luminoso.
Português IEC 825-1 (1993) EN 60825-1 (1997): Equipamento Laser Classe 1
Luz de laser - não olhar na direção do feixe.
Atenção: luz de laser quando aberto, não olhar na direção do feixe.
CAUTION – Use of controls or adjustments or performance of procedures other than those specified
herein result in hazardous laser light.
VORSICHT – Bei einer anders als hier beschriebenen Verwendung der Bedienelemente oder
Veränderungen oder einer anderen Ausführung der Arbeitsabläufe entsteht gefährliches Laserlicht.
ATTENTION – L’utilisation de contrôles/commandes ou de réglages ou l’exécution de procédures
autres que ceux précisés dans le présent document provoquent une lumière laser dangereuse.
Laser warnings
4
Regulatory statements
Intermec hereby declares that the MaxiScan 2210 has been tested and found compliant with the below
listed standards as required by the EMC Directive 89/336/EEC as amended by 92/31/EEC and by the
Low Voltage Directive 73/23/EEC as amended by 93/68/EEC:
EN55022 (1992) EN50082-1 (1998) EN60950 (1993)
USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. It generates, uses and can radiate radio frequency energy. If not installed and used in accordance
with the instructions, it may cause interference to radio communications. If this equipment causes interference, the
user will be required to correct the interference at the user’s own expense.
This equipment complies with the UL 1950 standard. This equipment must not be connected by the RJ connectors to
any type of telecommunications circuits.
Canada: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
This equipment complies with the UL 1950 standard. This equipment must not be connected by the RJ connectors to
any type of telecommunications circuits.
Cet équipement est conforme à la norme UL 1950. Cet équipement ne doit être connecté par les connecteurs RJ à
aucun type de circuits de télécommunication.
Australia-New Zealand: This equipment has been tested and found to conform to the Australian EMC
framework concerning Class B digital devices, prescribed by the Australian and New-Zealander
standard AS/NZS 3548.
Mexico: Este equipo cumple con la certificatión NOM.
The information contained in this document is for informational purposes only and is subject to change without notice.
No part of this document may be copied or reproduced in any manner without the prior written permission of Intermec
Technologies Corporation.
MaxiScan products are covered by patents issued or pending in the USA and other countries.
The word Intermec, the Intermec logo, MaxiScan and EasySet are either trademarks or registered trademarks of
Intermec.
Throughout this document, trademarked names may be used. Rather than put a trademark (™ or ®) symbol in every
occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and to the
benefit of the trademark owner, with no intention of infringement.
North America / Asia Pacific / Latin America • 6001 36th Avenue West, PO Box 4280, Everett, WA 98203-9280
Tel: +1 425 348 2600 • Fax: +1 425 348 2833 • U.S. service and technical support, tel: 1.800.755.5505 • Canadian
service and technical support, Tel: 1.800.688.7043
Europe / Middle East / Africa • Sovereign House, Vastern Road, Reading RG1 8BT, England
Tel: +44 (0) 118 987 9400 • Fax: +44 (0) 118 987 9401
Internet: http://www.intermec.com
E-mail: [email protected]
Technical information: http://datacapture.intermec.com
N309
© 2001 Intermec Technologies Corporation. 3-420049-00-011Revision level :All rights reserved.
-
1
-
2
-
3
Intermec MaxiScan 2210 Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Intermec MaxiScan 2210 User manual
Documents connexes
-
Intermec MaxiScan 2210 Getting Started Manual
-
-
-
-
Intermec MaxiScan 2100 Getting Started Manual
-
-
-
-
-