Intermec Sabre 1551 Getting Started Manual

Marque: Intermec

Modèle: Sabre 1551

Taper: Getting Started Manual

P/N 3-600049-01

Sabre 1551

Hand-held Scanner

Getting Started Guide

Anleitung für Einsteiger

Guia de IniciaçãoGuide de Démarrage

Guida IntroduttivaGuía de Iniciación

Connect scanner cable

Scanner cable depends

on your terminal

Cables and

accessories

Introduction

Full setup

Configuración completa

Configuration complète

Vollständige Konfiguration

Configurazione completa

Configuração completa

EasySet setup software

(on the CD-ROM)

Operating

Uso

Utilisation

Betrieb

Utilizzazione

Operação

Operator’s Guide

Basic setup

Configuración básica

Configuration de base

Grundkonfiguration

Configurazione di base

Configuração básica

Getting Started Guide

Use this Getting Started Guide to set up the Sabre 1551E laser scanner for most terminal

connections and symbologies. If necessary, use the EasySet setup software or Installa-

tion Manual for additional configuration possibilities and terminal connections.

Do not use this guide with the Sabre 1551A, B, or C.

Do not use Sabre 1551A, B, or C cables with the Sabre 1551E.

QWERTY Swedish / Finnish

QWERTY Italian

QWERTY Norwegian

QWERTY Danish

QWERTY Spanish

Customize parameters (optional)

(*) = default value

Postamble = Tab

Postamble = none

Postamble = Carriage Return

Postamble = Enter (*)

AZERTY French

QWERTY English

QWERTZ German

QWERTZ Swiss / French

Keyboard wedge (for PC)

System power OFF

Din/mini-Din adaptor cable

PC wedge cable

P/N 3-604037-00

Connect cables

System power ON

power supply

(normally not required)

QWERTY Portuguese

Select keyboard

Customize parameters (optional)

(*) = default value

9600 baud (*)

19200 baud

7 data bits (*)

8 data bits

No parity

Postamble = Carriage Return

Postamble = none

Even parity (*)

Odd parity

Postamble = Carriage Return + Line Feed (*)

RS-232 C

Connect cables

Scanner power ON

Standard RS-232 C cable

P/N 3-604032-00

System power OFF

System power ON

Read this code (standard RS-232 C

PC serial port compatible)

9600 baud, 7 data bits, even parity, 2 stop bits

postamble = carriage return + line feed

UPC-A, UPC-E, EAN-8, EAN-13

(UPC-A -> EAN-13)

UPC-A, UPC-E, EAN-8, EAN-13

(UPC-A -> UPC-A)

Code 128 / EAN 128

Code 39

Symbology

Disable all symbologies

Select symbology

Wand emulation

Wand emulation cable

P/N 3-606031-00

Connect cable

System power OFF

System power ON

Analog wand emulation - Intermec interface, white high

Digital wand emulation

Wand emulation

PDF417 (1551 0808 only)

1110

Full setup with EasySet

Default setup

Start EasySet software

Read this code

System power ON

Scanner power ON

System power OFF

Connect RS-232 C cable

(P/N 3-604032-00)

Test symbology

EasySet setup

1312

CAUTION – Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

VORSICHT – Bei einer anders als hier beschriebenen Verwendung der Bedienelemente oder

Veränderungen oder einer anderen Ausführung der Arbeitsabläufe kann es zu gefährlichen

Strahlungen kommen.

Siehe übersetztes Dokument auf der CD-ROM, um Sicherheitsanforderungen zu vervollständigen.

ATTENTION – L’utilisation de contrôles/commandes ou de réglages ou l’exécution de procédures

autres que ceux précisés dans le présent document peuvent provoquer une exposition dangereuse

aux radiations.

Laser warnings

The Sabre 1551 has a maximum laser output of 1mW at 630-680 nm and complies with the following

safety standards:

USA: CDRH - Class II Laser Product (CFR 21 Subpart J)

IEC 825-1 EN 60825-1 - Class 2 Laser Product (all Sabre 1551 models except 0601)

IEC 825-1 EN 60825-1 - Class 3A Laser Product (Sabre 1551 0601)

Fix these warning labels onto the product if they are not already present.

Collez les étiquettes d’avertissement sur votre produit.

Bringen Sie Warnetiketten auf dem Produkt an.

Fije las etiquetas de advertencia en el producto.

Cole as etiquetas de precaução no equipamento.

Un’etichetta di avviso per il laser è da applicare sul prodotto.

Sabre 1551 (all models except 0601)

Sabre 1551 (0601)

1514

USA & Canada: This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment is intended for operation in a commercial environment, in compliance with the requirements for a Class A digital device, pursuant

to part 15 of the FCC Rules and it must not be used in a residential environment. It generates, uses and can radiate radio frequency energy. If not

installed and used in accordance with the instructions, it may cause interference to radio communications. If this equipment causes interference,

the user will be required to correct the interference at the user’s own expense.

In order to maintain compliance with the FCC Rules, the I/O cables that interconnect between the device and any peripheral (such as a reader)

must be as specified by Intermec.

This device is UL listed (UL 1950/C22.2 No. 950) for safety when powered by a host system or by one of the following external Intermec power

supplies: P/N 0-302029-01 ~120V, 60 Hz.

Intermec hereby declares that the Sabre 1551E has been tested and found compliant with the below listed standards as required by

the EMC Directive 89/336/EEC as amended by 92/31/EEC and by the Low Voltage Directive 73/23/EEC as amended by 93/68/EEC:

EN55022, EN55024, EN60950

This device is TÜV GS licensed (EN 60950 and EN 60825-1) for safety when powered by a host system or by the following external Intermec power

supply: P/N 0-301029-01 ~230V, 50 Hz. For 240V applications use the power supply: P/N 0-303029-01 ~240V, 50 Hz.

Australia-New Zealand: This equipment has been tested and found to conform to the Australian EMC framework concerning

Class A digital devices, prescribed by the Australian and New-Zealand standard AS/NZS 3548.

Mexico: Este equipo cumple con la certificatión NOM.

The information contained in this document is for informational purposes only and is subject to change without notice. No part of this document

may be copied or reproduced in any manner without the prior written permission of Intermec Technologies Corporation.

Sabre products are covered by patents issued or pending in the USA and other countries.

The word Intermec, the Intermec logo, Sabre and EasySet are either trademarks or registered trademarks of Intermec.

Throughout this document, trademarked names may be used. Rather than put a trademark (™ or ®) symbol in every occurrence of a trademarked

name, we state that we are using the names only in an editorial fashion, and to the benefit of the trademark owner, with no intention of infringement.

North America / Asia Pacific / Latin America • 6001 36th Avenue West, PO Box 4280, Everett, WA 98203-9280

Tel: +1 425 348 2600 • Fax: +1 425 348 2833 • U.S. service and technical support, tel: 1 800 755 5505 • Canadian service and technical support,

tel: 1 800 688 7043

Europe / Middle East / Africa • Sovereign House, Vastern Road, Reading RG1 8BT, England • Tel: +44 (0)118 987 9400

Fax: +44 (0)118 987 9401

Internet: http://www.intermec.com

E-mail: [email protected]

Technical information: http://datacapture.intermec.com

Regulatory statements

N309

Intermec Sabre 1551 Getting Started Manual

Marque: Intermec

Modèle: Sabre 1551

Taper: Getting Started Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Intermec Sabre 1551

Intermec Sabre 1551 Getting Started Manual

Intermec Sabre 1551 Getting Started Manual

dans d''autres langues

Documents connexes

Autres documents