Aquatica Digital AquateX True Ofuro Installation & Care Manual

Marque
Aquatica Digital
Modèle
AquateX True Ofuro
Taper
Installation & Care Manual
True Ofuro
AquateX
™
Bathtub
Installation & Care Manual
USA / CANADA
Aquaticausa.com
Aquaticabath.ca
E: [email protected]
3
'-
0
1
/4
"
Ø3"
12°
1'-5 1/2"
Slope to the drawin -2 degrees
1
2
°
3
3
/
4
"
1
'-
8
1
/2
"
4'-3 1/2"
10 3/4"
2'-11 1/2"
1
'-
7
"
2 1/2"
2'-7"
1 3/4"
1
3
°
3'-4 3/4"
2 1/2"
2'-9 1/4"
Ø2"
1'-9 1/4"
2
'-
4
1
/2
"
2'-9 3/4"
1'-1 1/2"
4 1/2"
2'-3"
1'-8 1/4"
3'-1 3/4"
4"
1
2
°
3'-10 3/4"
1
'-
1
1
"
R1 3/4"
Aquaticausa.com
Aquaticabath.ca
E: info@aquaticabath.com
Aquaticausa.com
Aquaticabath.ca
E: info@aquaticabath.com
True Ofuro
AquateX
™
Bathtub
P-Trap
(not supplied)
Aquatica® Freestanding
Bath Installer™
(Ordered separately)
1½” flanged brass
tube for Aquatica
cable-drive and
concealed bath
wastes.
PLEASE NOTE: Parts marked with are supplied as part of Aquatica® Freestanding Bath Installer™ Kit (Ordered separately)
4.0”
!
Installation is completed by applying
silicone at several points between
the bottom panel and floor.
1
3
2 USA & CANADA - MANDATORY INSTALL
PROCEDURE
HANDLE
WITH CARE
DO NOT
DROP
1 ½ " male brass tube
– not included with tub
The 1.5” brass tubes & Aquatica
®
Freestanding Bath Installer™ are NOT included with bathtub
!
Aquatica
®
Freestanding
Bath Installer™
in the floor
- available for
purchase
separately
P-Trap - not
included
24 h
True Ofuro
AquateX
™
Bathtub
Aquaticausa.com
Aquaticabath.ca
E: [email protected]
TYPICAL FREESTANDING BATHTUB INSTALLATION PROCEDURE
Before you start:
• Ensure that the floor is even.
• The waste-overflow fitting is supplied with the product, however other accessories like the slip joint and
adaptors are not included and must be purchased separately.
• Because of the technical features of the product, it should be used only with the supplied waste-overflow
or specific 3rd party models that have been tested and approved by us.
• Place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the bottom
of the bathtub.
INSTALLATION SEQUENCE
• The True Ofuro bathtub is equipped with factory pre-installed overflow system .
• The waste pipe/p-trap connection must be made directly to the waste/drain outlet located at the bottom of the tub.
• Picture 1-2: the bathtub is leveled via a water level at the intended local installation area.
• Picture 3: place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the bottom of
the bathtub. Important note: during the installation, the bathtub should not be turned on its side to prevent its weight
from deflecting its monobloc sides. This is why it is important to use supports to raise the bathtub above the floor.
This will also provide you with easy access to the internal plumbing parts.
1
2
3
True Ofuro
AquateX
™
Bathtub
INSTALLATION SEQUENCE continued
• Picture 4: the water outlet pipe should be
connected.
• Picture 5: when the installation is completed,
the bathtub is taken down from the supports
( ie 2 x 4x4's).
If necessary, installation is completed by
applying silicone at several points between
the bottom panel and floor.
Fill the tub with water and check for any leaks
around the tub bottom.
TYPICAL FREESTANDING BATHTUB INSTALLATION PROCEDURE
Before you start:
• Ensure that the floor is even.
• The waste-overflow fitting is supplied with the product, however other accessories like the slip joint and
adaptors are not included and must be purchased separately.
• Because of the technical features of the product, it should be used only with the supplied waste-overflow
or specific 3rd party models that have been tested and approved by us.
• Place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the bottom
of the bathtub.
INSTALLATION SEQUENCE
• The True Ofuro bathtub is equipped with factory pre-installed overflow system .
• The waste pipe/p-trap connection must be made directly to the waste/drain outlet located at the bottom of the tub.
• Picture 1-2: the bathtub is leveled via a water level at the intended local installation area.
• Picture 3: place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the bottom of
the bathtub. Important note: during the installation, the bathtub should not be turned on its side to prevent its weight
from deflecting its monobloc sides. This is why it is important to use supports to raise the bathtub above the floor.
This will also provide you with easy access to the internal plumbing parts.
4
5
Use 1.5” flanged
brass tube.
Please refer to
our kit installation
guide on page 6
True Ofuro
AquateX
™
Bathtub
Aquaticausa.com
Aquaticabath.ca
E: [email protected]
Aquatica
®
Freestanding Bath Installer
™
(Using the Installation Kit is Strongly Recommended (Ordered Separately)
FEATURES
• 18 Gauge Epoxy coated Metal Deck Flange
• Designed to be installed in an 8” joist space
• Can be installed with Waterproofing Membrane
(*bronte™ NobleSeal TS Recommended)
• CSA Certified for Canadian and US markets
KIT INCLUDES
• 2 Brass Tailpieces (Fine Thread and Flanged)
• Freestanding Bath Installer™ assembly with 1-1/2” DWV
ABS tailpiece
• Cutting template
INSTALLATION TIPS
• Use 6.5” hole saw to cut sub floor (not included). Cutting tem-
plate included
• Do not cut the brass Tailpiece as this may cause a leak
• Secure Deck Flange with 6 screws (not included)
1
7
8
"
48mm
9
3
8
"
238mm
2"
52mm
1
1
4
"
32mm
4
1
8
"
103mm
6
1
4
"
159mm
1
1
2
"
39mm
1
1
2
"
38mm
8"
203mm
8"
203mm
1
1
2
"
38mm
1 ½ " brass tube for female threaded
stone bath wastes.
1 ½ " flanged brass tube for Aquatica
®
cable-drive and concealed bath wastes.
1
1
2
"
38mm
8"
203mm
8"
203mm
1
1
2
"
38mm
1 ½ " brass tube for female threaded
stone bath wastes.
1 ½ " flanged brass tube for Aquatica
®
cable-drive and concealed bath wastes.
Male Adapter Spg x MIPT - ABS DWV
for Aquatica
®
bath wastes with
Sch40 hub outlet.
Thread: 1 ½ NPSM (1 ½ IPS)
INSTALLATION INSTRUCTIONS
Attaches to Freestanding Bath W/O
A. Cut 6-1/2” (16.5 cm) hole into wood sub-floor
(use supplied Cutout Template).
B. Measure and cut ABS Tailpiece as necessary
to ensure a secure connection to P-Trap below.
C. Insert Freestanding Bath Installer™ assembly into floor
opening and connect to Pipe below.
D. Affix to sub-floor with 6 screws (not supplied)
A. Install flooring surface, leaving a 6-1/2” opening to
access Drain.
B. Affix the appropriate brass Tailpiece to the Waste
& Overflow. NOTE: DO NOT CUT THE BRASS TAIL-
PIECE AS THIS MAY CAUSE A LEAK.
Ensure the measurement between the base of the
Drain and P-Trap will accomodate the Tailpiece.
Other lengths available.
A. Cut out the Installation Label with a utility knife and
remove to expose the Drain.
B. Apply lubricant (supplied) to the Tailpiece.
C. Position the Tub and brass Tailpiece in-line with the Drain.
D. Carefully lower the tub with the installed brass Tailpiece
into the Red Collar in Drain assembly. Ensure Tailpiece is
fully engaged with Seal.
Aquatica
®
Freestanding Bath Installer
™
(Using the Installation Kit is Strongly Recommended (Ordered Separately)
1
2
3
IMPORTANT: Do not remove Installation Label until Step 3.
DO NOT CUT THE SUPPLIED BRASS TAILPIECE. Doing so may cause a leak.
Disassembling the drain or cutting the Tailpiece will void the warranty.
Aquaticausa.com
Aquaticabath.ca
E: [email protected]
Aquaticausa.com
Aquaticabath.ca
E: [email protected]
Maintenance Instructions
The smooth surface of your Aquatica
®
AquateX™
Bathtub accumulates hardly any dirt, and can be
maintained by simply cleaning with a soft cloth,
using a mild detergent in water, then wiping over
with a dry cloth.
Avoid using abrasive cleansers or solvents,
which will cause damage to the surface. Damage
caused by use of these products, or any other
inappropriate treatment, is not covered by our
guarantee.
Инструкция по уходу
Поверхность легко чистится. За счет
гладкости грязь к ней не прилипает. Для
регулярного ухода используйте мягкую
ткань, мыльный раствор и воду. После
чистки вытирайте поверхность сухой тканью,
которая хорошо впитывает влагу.
Не используйте губки с абразивной
поверхностью и агрессивные растворители,
которые могут повредить ванну.
Повреждения, возникшие вследствие
неправильного ухода, не покрываются
гарантией.
Installation & Entretien
Cette surface est facile à entretenir et à
nettoyer. Sa surface particulièrement lisse, ne
retiens que très peu la saleté. Un entretien
quotidien nécessite simplement l’utilisation d’un
chiffon doux, de l’eau et un peu de savon.
Essuyer avec un chiffon sec. L’utilisation de
détergents ou de solvants endommageraient
cette surface. Les dommages resultants d’un
traitement non conforme effectué par l’utilisateur
sont exclus de la garantie que nous offrons.
Manuale per il corretto mantenimento
La superficie necessita di pulizia ed accorgimenti
per il corretto mantenimento. Una superficie
liscia non accumula lo sporco. Usare una
spugnetta con del detergente non aggressivo per
una pulizia regolare. Asciugare con un
panno. Evitare l’uso di solventi o materiali
abrasivi: potrebbero rovinare la superficie.
Un danno causato da trattamento inappropriato
non verra’ coperto dalla garanzia.
Instrucciones para la correcta manutención
La superficie debe de ser limpiada y
adecuadamente mantenida. Una superficie lisa
no acumula suciedad.
Utilice una esponja con un detergente suave para
la limpieza diaria. Seque con un paño.
No utilice disolventes o materiales abrasivos ya
que podrían dañar la superficie.
Los daños causados por el tratamiento
inadecuado no serán cubiertos por la garantía.
True Ofuro - Maintenance Instructions
True Ofuro - Инструкция по уходу
True Ofuro - Installation & Entretien
True Ofuro - Manuale per il corretto mantenimento
True Ofuro - Instrucciones para la correcta manutención
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Aquatica Digital AquateX True Ofuro Installation & Care Manual

Marque
Aquatica Digital
Modèle
AquateX True Ofuro
Taper
Installation & Care Manual
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents