Lorex H32A2C Mode d'emploi

2K Wire-Free Security System

Quick Setup Guide

H32A Series

lorex.com

En

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use and handling of the product.

• Operate the camera within the specied temperature, humidity and voltage and use manufacturer

approved accessories.

• Do not disassemble the camera.

• Do not point the camera directly at the sun or a source of intense light.

• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based

cleaners.

Refer to the Battery Safety Insert.

• This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night

viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and

indicates that the camera lter is working.

• Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability

for use of its products that does not conform with local laws.

Battery Safety Precautions

Attention

Disclaimers

Camera Safety Precautions

A REGULATED UL / CSA APPROVED power supply is REQUIRED for use with this bundle (included).

Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty.

Thank you for your purchase!

How to get started with your

2K Wire-Free Security System

Contents

Package Contents

Section

Before You Start

Home Hub Overview

Home Hub Status Indicator

Home Hub Setup

1

2

3

4

5

Camera Overview

6

Camera Pairing to the Hub

App Live View

App Device Management

Camera Placement

Camera Mounting

8

9

10

11

12

Camera Status Indicator

7

Package Contents

Wire-Free Camera

Lorex Home Hub

Wire-Free Camera

(x2)*

Battery Pack

(x2)*

Mounting Bracket

(x2)*

Anchors (x6)*

Screws (x6)*

Mounting Template

(x2)*

Mounting Plate

(x2)*

Pre-inserted Memory

Card (x1)

Ethernet

Cable (x1)

Lorex Home Hub

(x1)

1

Power Adapter

(x1)

Power Adapter

(x1)*

6.6ft (2m)

Power Cable

(x1)

6.6ft (2m) Power

Cable (x1)*

*Dependent on additional accessory cameras included

Before You Start

2

1. Use the power adapters and cables to charge the batteries.

2. When fully charged, the battery status indicator will turn green.

To charge the battery pack:

Green - Battery fully chargedRed - Battery low

The camera batteries come partially charge (due to safety regulations). Please fully charge the

battery prior to use, and before you begin your setup. This will take 4-6 hours.

Home Hub Overview

3

1

2

3

4

5

6

7

1. Status indicator

2. Speaker

3. QR Code

4. Ethernet port

5. Power port

6. MicroSD card slot (included)

7. Pairing / reset button

FRONT

BACK

Home Hub Status Indicator

4

Status Description

(solid)

Operating correctly

(flashing)

Ready to connect to network

(flashing)

In pairing mode

(solid)

Factory reset

(flashing)

Disconnected from network

(alternating)

Firmware update in progress

(flashing)

Notication: Camera Detected Motion

Home Hub Setup

5

1. Connect power to the hub with the power adapter and

cable. When you hear the chime and the status indicator is

flashing green, the device is ready for setup.

2. Download the Lorex Home app by scanning the QR code.

3. Open the Lorex Home app, and sign in or create an

account.

4. Tap

+

in the app to add the device, then follow the in-app

instructions to complete the setup.

Recommended: Select Wired Connection and use the provided

Ethernet cable to connect the hub to your router.

Ensure you upgrade to the latest app and Hub rmware version.

Camera Overview

1

2

3

4

5

FRONT

BACK

9

8

7

6

1. Warning light

2. Status indicator

3. Microphone

4. Light sensor

5. Speaker

6. Power port

7. Threaded insert (for mounting)

8. Pairing / reset button

9. Bottom cover

6

Status Description

Off Privacy mode or battery needs recharging

(solid)

Operating correctly.

(flashing)

Ready for pairing or motion detected

(flashing)

Testing Wi-Fi signal strength

(solid)

Factory reset

(flashing)

Disconnected from network

(alternating)

Firmware update in progress

Camera Status Indicator

7

Camera Pairing to the Hub

8

1. Open the Lorex Home app.

2. Tap

+

beside the Hub device and follow the in-app

instructions.

Note: Make sure you only pair 1 camera at a time.

3. Once the camera is set up, re-install the bottom cover

by carefully aligning the arrow and the unlock symbols.

Push and twist the bottom cover clockwise to lock.

4. Place or mount the camera in the desired location.

See sections 11 and 12.

5. To pair additional cameras, repeat steps 2-4.

From the Home screen or Live View, swipe left to see

the additional cameras.

App Live View

9

Camera settings

Pause/play

Fullscreen view

Video quality

SD/HD

Viewing modes

Play back recorded videos

Audio on/off

10

App Device Management

Privacy mode

(all cameras)

Hub settings

Remove camera

Add camera

Wi-Fi strength indicator

Battery status indicator

Notication indicator

Privacy mode indicator

11

Camera Placement

• Place the camera on any flat surface or mount it to a wall.

• Do not place the camera near air conditioners and other

air outlets.

• Install the camera at the recommended angle and height

per the guidelines below.

Optimal accuracy for objects within

0.5-32ft (2~10m).

Note: Accuracy of person detection will be influenced by multiple factors, such as the

person’s distance from the camera, the height of the person, and the height and angle of the camera.

Night vision will also impact the accuracy and distance of detection.

To optimize motion detection accuracy when:

Mounted on a wall Placed on a shelf

Optimal accuracy for objects within

6.5ft to 32ft (2~10m).

Distance Distance

Angle the camera around 15°-30°

down from the level position.

Angle

Install the camera between 7-10ft

(2~3m) off of the ground.

Height

Place the camera on a flat surface.

Make sure the flat surface/shelf is not

obstructing the camera’s eld of view.

Place the camera between 4.5ft to

6.5ft (1.5~2m) off of the ground.

12

Camera Mounting

Screws

Anchors

(Optional)

Mounting

surface

Mounting template

Mounting plate

Adjustable nut

Camera

Mounting

bracket

1. Place the mounting template to the desired location.

Optional: Drill 7/32” (5.5mm) holes for the anchors.

2. Align the arrows of the mounting plate and template. Using a Philips screwdriver and the

provided screws, secure the mounting plate to the surface.

To install the camera:

3. Align the arrows between the mounting

bracket and plate. Push the bracket in to

install, then slide down to lock in place.

You will hear a ‘click’ when the bracket is

installed.

4. Attach the camera to the mounting bracket

using the thread insert at the rear of the

camera. Rotate the camera clockwise until

attached, then tighten/fasten into place with

the adjustable nut.

5. Adjust the camera to the desired angle.

Note: If the camera is not holding in place or

difcult to adjust, slide the bracket up to detach

from the mounting plate. Tighten or loosen the

3 screws at the back of the mounting bracket to

adjust accordingly. Repeat steps 3-5 to re-install.

Back - Mounting bracket

Adjustable screws

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference that may cause undesired operation.

As our products are subject to continuous improvement, Lorex reserves the right to modify product design,

Need help?

Visit help.lorex.com for up-to-date information and resources:

• Download product guides

• Watch how-to-videos

• Find related troubleshooting tips & FAQs

H32A-Series_QSG_TRILINGUAL_R1

Register your product

Please see our full Terms of Service and Limited Hardware Warranty Policy visit,

lorex.com/warranty.

Système de sécurité 2K sans fil

Le guide de configuration rapide

Série H32A

lorex.com

Fr

• Lisez attentivement ce guide et gardez-le pour consultation ultérieure.

• Veuillez suivre les directives pour assurer une utilisation et une manipulation sécuritaires du produit.

• Faites fonctionner la caméra dans les limites de température, d’humidité et de tension spéciées et

utilisez les accessoires approuvés par le fabricant.

• Ne démontez pas la caméra.

• Ne pointez pas votre caméra vers le soleil ou une source intense de lumière.

• Un nettoyage périodique peut s’avérer nécessaire. Utilisez uniquement un linge humide. N’utilisez pas

de nettoyants à base de produits chimiques

abrasifs.

Reportez-vous à l’encart «Sécurité pour les piles».

• Cet appareil comprend un ltre IR mécanique autonome. Lorsque la caméra passe du mode diurne au

mode nocturne, un bruit de clic provenant de la caméra peut être entendu. Ce clic est normal et indique

que le ltre de la caméra fonctionne.

• L’enregistrement audio sans consentement est illégal sur certains territoires. LorexCorporation décline

toute responsabilité concernant l’usage de produits non conformes aux lois locales.

Mesures de sécurité pour les piles

Attention

Clauses de non-responsabilité

Mesures de sécurité pour la caméra

Un bloc d’alimentation STABILISÉ et CERTIFIÉUL/CSA est OBLIGATOIRE pour l’utilisation de cet

ensemble (fourni).

L’utilisation d’un bloc d’alimentation non réglementé et non conforme peut endommager ce produit et

annuler la garantie.

La page charge ...

Lorex H32A2C Mode d'emploi

Lorex H32A2C Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents