Sanus VMD1 Guide d'installation

Sanus
Marque
Sanus
Modèle
VMD1
Catégorie
Supports muraux à panneau plat
Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
VMD1
(6901-002123 <01>)
Sanus
6436 City West Parkway
Eden Prairie, MN 55344 USA
Customer Service
Americas: 800-359-5520 • 952-225-6013 • [email protected]
Europe, Middle East, and Africa: + 31 40 2324700 • [email protected]
Asia Pacific: 86 755 8996 9226 • [email protected]
www.sanus.com
VMD1 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for
accuracy, completeness or sufficiency of
the information contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the VMD1 Monitor Arm
up to (and including) the display does not exceed 25 lbs
(11.34 kg) per arm. Use with products heavier than the
maximum weight indicated may result in collapse of the
mount and its accessories causing possible injury.
DIMENSIONS
14.70±6.5
3.94
100
2.95
75
CABLE
MANAGEMENT
COVER
CABLE
MANAGEMENT
COVER QUICK RELEASE
VESA INTERFACE
90 INTERFACE
ROTATION
MAX 19.9 [505.5]
EXTENSION
MIN 2.09 [53.14]
.75
MAX 2.50 [63.5]
19.05
DESKTOP THICKNESS RANGE
4.66
118.
3
PITCH TENSION
ADJUSTMENT
PITCH RANGE
10
DOWN
75
UP
VMD1
(6901-002123 <01>)
Milestone AV Technologies, a Duchossois Group Company.
All rights reserved. Sanus is a division of Milestone.
All other brand names or marks are used for identification
purposes and are trademarks of their respective owners.
VMD1
Installation Instructions
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
(6901-002123 <01>)
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/16" (included)
1/8" (included)
A (1)
[monitor arm]
B (4)
M4x14mm
C (4)
M4x25mm
D (4)
M10x5.3x10
3/16"
1/8"
E (1)
F (1)
VMD1 Installation Instructions
4
(6901-002123 <01>)
Installation Instructions VMD1
5
Connecting VMD1 to Desk
1. Loosen clamp screw until enough space is created between
clamp and mount to allow for desk mounting. (See Figure 1)
NOTE: If space is limited behind desk (i.e. against wall, etc.),
remove clamp entirely in Step 1 and reattach clamp
prior to Step 3!
2. Place mount on top of desk at desired mounting location.
(See Figure 1)
3. Tighten clamp using clamp screw until mount is securely
fastened to desk. (See Figure 1)
Figure 1
1
1
2
3
desk
(6901-002123 <01>)
VMD1 Installation Instructions
6
Display Installation
1. Remove quick release faceplate from mount by pressing
quick release tab and sliding faceplate off mount. (See
Figure 2)
Figure 2
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! See
Display Removal section for details.
2. Carefully place display face down on protective surface.
3. Connect faceplate to display
For flush mounting hole installation:
• Using Phillips screwdriver, carefully install four
M4x14mm screws (B) through corresponding
holes on faceplate and into the mounting holes on
the display. (See Figure 3)
Figure 3
For recessed mounting hole installation:
• Place four spacers (D) on top of mounting holes
on back of display. (See Figure 9)
• Using Phillips screwdriver, carefully install f
our
M4x25mm screws (C) through corresponding
holes on faceplate, spacers (D) and into the
mounting holes on the display. (See Figure 4)
Figure 4
4. Position display with faceplate attached above mount. (See
Figure 5)
5. Slide faceplate onto mounting head until quick release tab
clicks into place. (See Figure 5)
Figure 5
quick release tab
1
1
(B) x 4
quick release
faceplate
(for flush mounting holes)
3
(for recessed mounting holes)
(C) x 4
(D) x 4
quick release
faceplate
3
5
(6901-002123 <01>)
Installation Instructions VMD1
7
Adjustments
Head Tilt Adjustment
1. Adjust head tilt to desired tilt position. (See Figure 6)
2. Adjust head tilt tension screw to change the adjustment
tension. (See Figure 6)
Height Adjustment
NOTE:
Turn clockwise to reduce tension for lighter displays
and counter-clockwise to increase tension for heavier
displays.
Pivot Adjustment
1. Adjust pivot position as desired. (See Figure 6)
2. Use 3/16" hex key (E) to adjust pivot point tension screws
to change pivot adjustment tension. (See Figure 6)
Figure 6
Pivot Adjustment Range
1. Adjust arm angle as desired up to 90 degrees in either
direction. (See Figure 7)
WARNING: Swinging the arm beyond 90 degrees may
result in the mount slipping off the desk causing serious
injury!
Figure 7
(top view)
+/- 90 degrees range
of motion
edge of desk
(6901-002123 <01>)
Portrait Adjustment
1. The monitor may be adjusted 90 degrees in either direction
in order to provide a portrait view of the monitor. (See Figure
8)
Figure 8
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! See
Display Removal section for details.
head tilt
pivot point
tension
tension
Reduce tension
Increase tension
(lighter display)
(heavier display)
Do NOT overtension
adjustment tension
screw.
3
CAUTION: OVERTENSIONING THE HEIGHT-
ADJUSTMENT TENSION SCREW MAY CAUSE DAMAGE!
Do NOT overtighten height-adjustment tension screw when
adjusting tension for lighter or heavier displays.
1. Adjust arm height to desired level. (See Figure 6)
2. Open cable management cover on upper arm to expose
height-adjustment tension screw. See Cable Management
section for details.
3. Use 1/8" hex key (F) to adjust height-adjustment tension
screw to change adjustment tension. (See Figure 6)
VMD1 Installation Instructions
8
Cable Management
1. Use screwdriver to unhinge tab on either end of cable
management cover on upper arm. (See Figure 9)
2. Slide screwdriver along edge of cover until remaining tabs
are unhinged and cover is in the "open" position. (See
Figure 9)
Figure 9
Figure 10
3. Route cables through cable management channels. (See
Figure 10)
IMPORTANT! Be sure to leave enough slack in the
cables near display and arm joint to allow for full arm
articulation!
4. Close cable management covers on monitor arm. (See
Figure 10)
5. Repeat Steps 1-4 for lower arm.
cable management cover
1
2
2
2
4
4
3
3
cable (typical)
(6901-002123 <01>)
Display Removal
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! (See
Figure 11)
1. Make sure display is in the upright position.
2. Remove quick release faceplate from mount by pressing
quick release tab and sliding faceplate off mount. (See
Figure 11)
Figure 11
quick release tab
2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Sanus VMD1 Guide d'installation

Sanus
Marque
Sanus
Modèle
VMD1
Catégorie
Supports muraux à panneau plat
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents