Makita XT328M-XRM04B-XAG03Z Mode d'emploi

Symbols

The followings show the symbols used for the charger and battery. Be sure that you understand their meaning before

use.

Symboles

Nous donnons ci-dessous les symboles utilisés pour le chargeur et la batterie. Assurez-vous que vous en avez bien

compris la signification avant d’utiliser l’outil.

Símbolos

A continuación se muestran los símbolos utilizados con el cargador y la batería. Asegúrese de que entiende su signifi-

cado antes de usarla.

Fast Charger

Chargeur rapide

Cargador rápido

• Ready to charge

• Prêt à recharger

• Preparación para la carga

• Charging

• En charge

• Cargando

• Charging complete

• Recharge terminée

• Completada la carga

• Delay charge (Battery cooling or too cold battery)

• Charge différée (Batterie en cours de refroidissement ou batterie trop froide)

• Retraso de la carga (La batería se está enfriando o está muy fría)

• Defective battery

• Batterie défectueuse

• Batería defectuosa

• Conditioning

• Recharge normale

• Acondicionamiento

• Cooling abnormality

• Problème de refroidissement

• Anormalidad en la carga

DC18RA

DC18RC

2

• Do not short batteries.

• Ne jamais court-circuiter les bornes d’une batterie.

• No provoque un cortocircuito en las baterías.

IMPORTANT: Read Before Using.

IMPORTANT : Lire ce qui suit avant d’utiliser cet outil.

IMPORTANTE: Leer antes de usar.

3

ENGLISH

Specifications

• Manufacturer reserves the right to change specifications without notice.

• Note: Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

1. SAVE THESE INSTRUCTIONS — This manual contains

important safety and operating instructions for battery charger.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) bat-

tery, and (3) product using battery.

3. CAUTION — To reduce risk of injury, charge only MAKITA rechargeable batteries marked on the charger

label. Other types of batteries may burst causing personal injury and damage.

4. Non-rechargeable batteries cannot be charged with this battery charger.

5. Use a power source with the voltage specified on the nameplate of the charger.

6. Do not charge the battery cartridge in presence of flammable liquids or gases.

7. Do not expose charger to rain or snow.

8. Never carry charger by cord or yank it to disconnect from receptacle.

9. After charging or before attempting any maintenance or cleaning, unplug the charger from the power

source. Pull by plug rather than cord whenever disconnecting charger.

10. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage

or stress.

11. Do not operate charger with damaged cord or plug. If the cord or plug is damaged, ask Makita authorized

service center to replace it in order to avoid a hazard.

12. Do not operate or disassemble charger if it has received a sharp blow, been dropped, or otherwise dam-

aged in any way; take it to a qualified serviceman. Incorrect use or reassembly may result in a risk of elec-

tric shock or fire.

13. The battery charger is not intended for use by young children or infirm persons without supervision.

14. Young children should be supervised to ensure that they do not play with the battery charger.

15. Do not charge battery cartridge when room temperature is BELOW 10°C (50°F) or ABOVE 40°C (104°F).

When the battery temperature is under 0°C (32°F), charging may not start.

16. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.

17. Do not allow anything to cover or clog the charger vents.

Charging

1. Plug the battery charger into the proper AC voltage source. Charging light will flash in green color repeatedly.

2. Insert the battery cartridge into charger until it stops adjusting to the guide of charger. Terminal cover of charger

can be opened with inserting and closed with pulling out the battery cartridge.

3. When the battery cartridge is inserted, the red charging light will light up and charging will begin with a preset brief

melody sound coming out for assurance as to which sound will come out to notify the completion of charging.

4. With finish of charge, the charging light will change from red one to green one and the melody sound or buzzer

sound (a long beep) comes out to notify completion of charge.

5. Charging time varies by temperature (10°C (50°F) – 40°C (104°F)) that battery cartridge is charged at and

conditions of the battery cartridge, such as a battery cartridge which is new or has not been used for a long period

of time.

6. After charging, remove the battery cartridge from charger and unplug the charger.

Changing melody of completed charging

1. Inserting the battery cartridge into charger brings out last preset brief melody sound of completed charging.

2. Removing and re-inserting it within five seconds after this action makes the melody sound change.

3. Every time removing and re-inserting it within another five seconds after this, the melody sound changes in order.

4. When the desired melody sound comes out, leave the battery cartridge being inserted and the charge will begin.

When a “short beep” mode is selected, no completed charging signals comes out. (Silent Mode)

Model DC18RA DC18RC

Input A.C. 120 V 50 – 60 HZ

Output D.C.7.2V–18V

Weight 0.88 kg (1.94 lbs) 0.77 kg (1.70 lbs)

4

5. With finish of charge, the green light remains lit with the red light going out and the melody sound preset at the

insertion of battery cartridge or buzzer sound (a long beep) comes out to notify completion of charge. (In selected

silent mode, no sounds come out.)

6. Preset melody sound remains stored even when the charger is unplugged.

NOTE:

• The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other

manufacturer’s batteries.

• When you charge a battery cartridge which is new or has not been used for a long period of time, it may not accept a

full charge until after discharging it completely and recharging a couple of times. (Ni-MH battery only)

• If charging light may flash in red color, battery condition is as below and charging may not start.

– Battery cartridge from just-operated tool or battery cartridge that has been left in a location exposed to direct sun-

light for a long time.

– Battery cartridge that has been left for a long time in a location exposed to cold air.

When the battery cartridge is too hot, charging will begin after the cooling fan installed in the charger cools the bat-

tery cartridge. Charging will begin after the battery cartridge temperature reaches the degree at which charging is

possible. When the temperature on battery is more than approx. 70°C, two charging lights may flash in red color, and

when approx. 50°C – 70°C, one charging light in red color.

• If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger

or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.

Cooling system

• This charger is equipped with cooling fan for heated battery in order to enable the battery to prove its own

performance. Sound of cooling air comes out during cooling, which means no trouble on the charger.

• Yellow light will flash for warning in the following cases.

– Trouble on cooling fan

– Incomplete cool down of battery, such as, being clogged with dust

The battery can be charged in spite of the yellow warning light. But the charging time will be longer than usual in this

case.

Check the sound of cooling fan, vent on the charger, which can be sometime clogged with dust.

• The cooling system is in order although no sound of cooling fan comes out, if the yellow warning light will not flash.

• Always keep clean the vent on charger and battery for cooling.

• The products should be sent to repair or maintenance, if the yellow warning light will frequently flash.

Conditioning charge

Conditioning charge can extend the life of battery by automatically searching the optimum charging condition for the

batteries in every situation.

The battery employed in the following conditions repeatedly requires “conditioning charge” to prevent fast wear out. In

that case, yellow light lights up.

1. Recharge of battery with its high temperature

2. Recharge of battery with its low temperature

3. Recharge of full charged battery

4. Over-discharge of battery (continue to discharge battery in spite of down of power.)

The charging time of such battery is longer than usual.

Note:

• It may take twice the above charging time to the maximum because of the optimal charging selected according to the

temperature (10°C (50°F) – 40°C (104°F)), conditions of battery cartridge and maintenance charge.

Voltage 9.6 V 12 V 14.4 V Capacity (Ah) Charging time (Minutes)

Number of cells 8 10 12

Ni-MH Battery cartridge

——— 1.7 20

BH9020A — — 2.0 20

— BH1220/C BH1420 2.0 15

——— 2.7 20

BH9033A — — 3.3 30

— BH1233/C BH1433 3.3 22

Voltage 14.4 V 18 V 14.4 V 18 V

Charging time (Minutes)

Number of cells 4 5 8 10

Li-ion Battery cartridge

BL1415 BL1815 — — 15

— — BL1430 BL1830 22

5

FRANÇAIS

Spécifications

• Le fabricant se réserve le droit de modifier sans avertissement les spécifications.

• Remarque : Les spécifications peuvent varier selon les pays.

• Poids selon la procédure EPTA 01/2003.

LES CONSIGNES DE SECURITE IMPORTANTES

ATTENTION :

1. CONSERVEZ CES INSTRUCTIONS — Ce manuel renferme

des consignes de sécurité et d’utilisation importantes pour le chargeur de batterie.

2. Avant d’utiliser le chargeur de batterie, lisez toutes les étiquettes d’instruction et de précaution apposées

sur (1) le chargeur de batterie, sur (2) la batterie et sur (3) le produit utilisant la batterie.

3. ATTENTION — Pour réduire le risque de blessure, ne chargez que les batteries rechargeables MAKITA qui

figurent sur l’étiquette du chargeur. Les autres types de batteries peuvent causer des blessures et entraî-

ner des dommages en explosant.

4. Il n’est pas possible de charger des batteries de type non rechargeable avec ce chargeur.

5. Utilisez une source d’alimentation dont la tension correspond à celle spécifiée sur la plaque signalétique

du chargeur.

6. Ne chargez pas la cartouche de batterie en présence de liquides ou gaz inflammables.

7. N’exposez pas le chargeur à la pluie ou à la neige.

8. Évitez de transporter le chargeur en le tenant par son cordon d’alimentation, et de tirer directement sur le

cordon pour le débrancher.

9. Avant de charger la batterie ou d’y effectuer tout travail d’entretien ou de nettoyage, débranchez le char-

geur de sa source d’alimentation. Pour débrancher le chargeur, tirez toujours le cordon par sa fiche, non

par le cordon lui-même.

10. Assurez-vous que le câble n’est pas placé de façon à être piétiné, à faire trébucher quelqu’un ou à subir

quelque dommage ou tension que ce soit.

11. N’utilisez pas le chargeur avec un cordon ou une fiche endommagé. Si le cordon ou la fiche est endom-

magé, faites-le remplacer dans un centre de service agréé Makita pour éviter tout danger.

12. Évitez d’utiliser ou démonter le chargeur après qu’il ait reçu un choc violent, ait été échappé ou ait subi

quelque dommage que ce soit. Portez-le chez un réparateur qualifié. Une utilisation ou un remontage

maladroit peut entraîner un risque de choc électrique ou d’incendie.

13. Ce chargeur ne doit pas être utilisé sans supervision par les jeunes enfants et par les personnes handica-

pées.

14. Les jeunes enfants doivent être surveillés pour s’assurer qu’ils ne jouent pas avec le chargeur.

15. Ne chargez pas la batterie lorsque la température de la pièce est INFÉRIEURE à 10 °C ou SUPÉRIEURE à

40 °C. Il se peut que la charge ne commence pas lorsque la température de la batterie est inférieure à 0 °C.

16. Ne tentez pas d’utiliser un transformateur élévateur, un groupe électrogène ou une prise de courant con-

tinu.

17. Ne laissez rien recouvrir ou boucher les ouvertures du chargeur.

Charge

1. Branchez le chargeur sur une source d’alimentation secteur dont la tension est adéquate. Le témoin de charge

clignote en vert de manière répétée.

2. Insérer la batterie dans le chargeur jusqu’à ce qu’elle s’arrête, ajustée sur le guide du chargeur. Le couvre-bornes

du chargeur peut être ouvert en insérant la batterie, et fermé en la retirant.

3. Lorsque vous insérez la batterie, le témoin de charge rouge s’allume et la charge commence ; une courte mélodie

préréglée est alors émise pour vous indiquer quel sera le son émis pour vous informer de l’achèvement de la

charge.

4. Lorsque la charge est terminée, le témoin de charge passe du rouge au vert et une mélodie ou une sonnerie (un

long bip) est émise pour vous informer de l’achèvement de la charge.

5. Le temps de charge varie suivant la température environnante (10°C (50°F) – 40°C (104°F)) à laquelle s’effectue

la charge de la batterie, et suivant l’état de la batterie, comme par exemple si elle est neuve ou si elle est restée

inutilisée pendant longtemps.

6. Après de la charge, retirez la batterie et débranchez le chargeur.

Modèle DC18RA DC18RC

Entrée C.A. 120 V 50 – 60 Hz

Sortie C.C. 7,2 V – 18 V

Poids 0,88 kg (1,94 lbs) 0,77 kg (1,70 lbs)

6

Changer la mélodie de charge terminée

1. Lorsque vous insérez la batterie dans le chargeur, le chargeur émet la dernière courte mélodie préréglée

d’indication de charge terminée.

2. Si vous retirez et réinsérez la batterie dans les cinq secondes qui suivent cette action, la mélodie changera.

3. Chaque fois que vous retirez et réinsérez la batterie dans les cinq secondes par la suite, la mélodie change dans

l’ordre préétabli.

4. Lorsque la mélodie désirée est émise, laissez la batterie insérée et la charge commencera. Si vous sélectionnez le

mode “court bip”, aucun signal de charge terminée ne sera émis. (Mode silencieux)

5. Lorsque la charge est terminée, le témoin de charge vert demeure allumé et le témoin rouge s’éteint, et la mélodie

ou la sonnerie (un long bip) préréglée au moment de l’insertion de la batterie est émise pour vous informer de

l’achèvement de la charge. (Si le mode silencieux est sélectionné, aucun son n’est émis.)

6. La mélodie préréglée demeure en mémoire même lorsque vous débranchez le chargeur.

NOTE :

• Le chargeur de batterie est conçu pour les batteries Makita. Ne jamais l’utiliser à d’autres fins ou avec les batteries

d’autres fabricants.

• Lorsque vous chargez une cartouche de batterie neuve ou restée inutilisée pendant une période prolongée, il se

peut que vous deviez la recharger et la décharger à quelques reprises avant qu’elle n’accepte une charge complète.

(Batterie au Ni-MH seulement)

• Si le témoin de charge clignote en rouge, l’état de la batterie est tel qu’indiqué ci-dessous et il se peut que la charge

ne commence pas.

– Cartouche de batterie d’un outil qui vient tout juste d’être utilisé, ou cartouche de batterie qui a été laissée long-

temps dans un endroit exposé directement aux rayons du soleil.

– Cartouche de batterie qui a été laissée longtemps dans un endroit exposé à de l’air froid.

Lorsque la batterie est trop chaude, la charge ne commence qu’une fois la batterie refroidie par le ventilateur de

refroidissement du chargeur. La charge commencera lorsque la température de la cartouche de batterie aura atteint

le degré pour lequel la charge est possible. Lorsque la température de la batterie est supérieure à environ 70°C,

deux témoins de charge peuvent clignoter en rouge, tandis qu’à une température d’environ 50°C à 70°C, un seul

témoin clignote en rouge.

• Si le témoin de charge clignote alternativement en vert et en rouge, la charge n’est pas possible. Les bornes du

chargeur ou de la batterie sont alors bloquées par la poussière, ou bien la batterie est soit usée, soit endommagée.

Système de refroidissement

• Ce chargeur est doté d’un ventilateur de refroidissement pour batterie chaude afin de permettre à la batterie de four-

nir son plein rendement. Un son de refroidissement d’air s’échappe pendant le refroidissement, ce qui signifie que le

chargeur fonctionne correctement.

• Un témoin jaune d’avertissement clignote dans les cas suivants.

– Problème de ventilateur de refroidissement.

– Refroidissement insuffisant de la batterie, causé par une accumulation de poussière, etc.

La batterie peut être chargée même si le témoin jaune d’avertissement est allumé. Mais dans ce cas, le temps de

charge sera plus long que d’ordinaire.

Vérifier le son du ventilateur de refroidissement, ainsi que les évents du chargeur, où s’accumule parfois de la pous-

sière.

• Le système de refroidissement fonctionne normalement si le témoin jaune d’avertissement ne clignote pas, et ce

même si aucun son ne provient du ventilateur de refroidissement.

• Toujours garder les évents du chargeur et de la batterie propres pour permettre le refroidissement.

• Si le témoin jaune d’avertissement clignote souvent, les produits devraient être envoyés pour réparation ou entre-

tien.

Charge de remise en condition

La charge de remise en condition peut faire augmenter la durée de vie de la batterie en effectuant automatiquement

une recherche du niveau de charge optimale des batteries dans toute situation.

Une batterie utilisée à plusieurs reprises dans les conditions suivantes nécessitera une “charge de remise en

condition” pour éviter qu’elle ne s’use rapidement. Dans ce cas, le témoin jaune s’allume.

1. Recharge de la batterie alors qu’elle est très chaude.

2. Recharge de la batterie alors qu’elle est très froide.

3. Recharge d’une batterie déjà complètement chargée.

4. Décharge excessive de la batterie (continuer de décharger la batterie malgré l’absence d’alimentation).

Le temps de charge est alors plus long que d’ordinaire.

7

Note :

• La charge complète peut prendre jusqu’à deux fois plus de temps que le temps indiqué ci-dessus, en raison de la

température (10°C (50°F) – 40°C (104°F)), de l’état de la batterie ou de la charge d’entretien.

Tension 9,6 V 12 V 14,4 V

Capacité (Ah) Temps de charge (en minutes)

Nombre de cellules 8 10 12

Cartouche de batterie

au Ni-MH

——— 1,7 20

BH9020A — — 2,0 20

— BH1220/C BH1420 2,0 15

——— 2,7 20

BH9033A — — 3,3 30

— BH1233/C BH1433 3,3 22

Tension 14,4 V 18 V 14,4 V 18 V

Temps de charge (en minutes)

Nombre de cellules 4 5 8 10

Cartouche de batterie

au Li-ion

BL1415 BL1815 — — 15

— — BL1430 BL1830 22

8

ESPAÑOL

Especificaciones

• El fabricante se reserva el derecho a cambiar las especificaciones sin aviso.

• Nota: Las especificaciones podrán cambiar de un país a otro.

• Peso de acuerdo con el procedimiento EPTA 01/2003.

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

PRECAUCION:

1. GUARDE ESTAS INSTRUCCIONES — Este manual contiene ins-

trucciones de seguridad y de funcionamiento importantes para el cargador de baterías.

2. Antes de utilizar el cargador de baterías, lea todas las instrucciones e indicaciones de precaución sobre

(1) el cargador de baterías, (2) la batería, y (3) el producto con el que se utilice la batería.

3. PRECAUCION — Para reducir el riesgo de sufrir heridas, cargue solamente las baterías recargables

MAKITA marcadas en la etiqueta de cargador. Otros tipos de baterías podrán explotar y ocasionar heridas

personales y daños.

4. Con este cargador de baterías no se pueden cargar baterías no recargables.

5. Utilice una fuente de alimentación cuya tensión sea igual a la especificada en la placa de características

del cargador.

6. No cargue el cartucho de batería en presencia de líquidos o gases inflamables.

7. No exponga el cargador a la lluvia ni a la nieve.

8. No coja nunca el cargador por el cable ni tire del cable para desconectarlo de la toma de corriente.

9. Después de la carga o antes de intentar cualquier mantenimiento o limpieza, desconecte el cargador de la

toma de corriente. Tire de la clavija y no del cable siempre que quiera desconectar el cargador.

10. Asegúrese de que el cable quede tendido de forma que no lo pueda pisar, tropezar con él, ni que esté

sometido a daños o desgaste de ningún tipo.

11. No utilice el cargador si su cable o clavija están dañados. Si el cable o la clavija están dañados, pida a un

centro de servicio autorizado de Makita que los reemplace para evitar riesgos.

12. No utilice ni desarme el cargador si este ha recibido un fuerte golpe, lo ha dejado caer, o si se ha dañado

de cualquier otra forma; llévelo a un técnico cualificado para que se lo arregle. Una utilización o montaje

de sus piezas incorrecto podrá acarrear un riesgo de descarga eléctrica o incendio.

13. El cargador de baterías no ha sido pensado para ser utilizado por niños pequeños ni personas frágiles

sin supervisión.

14. Los niños pequeños deberán ser supervisados para asegurarse de que no juegan con el cargador de baterías.

15. No cargue el cartucho de batería cuando la temperatura esté por DEBAJO de los 10°C o por ENCIMA de

los 40°C. Cuando la temperatura esté por debajo de los 0°C, es posible que la carga no se inicie.

16. No intente utilizar un transformador elevador de tensión, un generador a motor ni una toma de corriente

de corriente contínua.

17. No permita que cosa alguna tape u obstruya los orificios de ventilación del cargador.

Carga

1. Conecte el cargador de baterías en una toma de corriente de la tensión de CA apropiada. La luz de carga

parpadeará en color verde repetidamente.

2. Inserte el cartucho de batería en el cargador hasta que haga tope ajustándose a la guía del cargador. La tapa del

terminal del cargador se abre al insertar el cartucho de batería y se cierra al sacarlo.

3. Cuando se inserte el cartucho de batería, se encenderá la luz de carga roja y comenzará la carga con un sonido

de melodía breve programado emitido como aseguramiento del sonido que se emitirá para notificar la terminación

de la carga.

4. Con la terminación de la carga, la luz de carga cambiará de rojo a verde una vez y se emitirá el sonido de melodía

o sonido de zumbador (un pitido largo) para notificar la terminación de la carga.

5. El tiempo de carga varía en función de la temperatura (10°C (50°F) – 40°C (104°F)) a la que se carga el cartucho

de batería y las condiciones del cartucho de batería, tal como si es un cartucho de batería nuevo o no ha sido

utilizado durante un periodo de tiempo largo.

6. Después de cargar, extraiga el cartucho de batería del cargador y desconecte el cargador.

Modelo DC18RA DC18RC

Entrada

120 V

50 – 60 Hz

Salida 7,2Vcc–18Vcc

Peso 0,88 kg (1,94 lbs) 0,77 kg (1,70 lbs)

9

Cambio de la melodía de carga terminada

1. Al insertar el cartucho de batería en el cargador se emite el último sonido de melodía breve programado.

2. El sonido de melodía puede cambiarse extrayendo y reinsertando antes de cinco segundos el cartucho de batería.

3. Cada vez que se extraiga y reinserte antes de otros cinco segundos, el sonido de melodía cambiará en orden.

4. Cuando se emita el sonido de melodía deseado, deje el cartucho de batería insertado y comenzará la carga.

Cuando se seleccione el modo "pitido corto", no se emitirán señales de carga terminada. (Modo silencio)

5. Con la terminación de la carga, la luz verde permanece encendida, la luz roja se apaga y se emite el sonido de

melodía programado al insertar el cartucho de batería o sonido de zumbador (un pitido largo) para notificar la

terminación de la carga. (Si se ha seleccionado el modo silencio, no se emitirán sonidos.)

6. El sonido de melodía permanecerá almacenado aunque desenchufe el cargador.

NOTAS:

• El cargador de baterías es sólo para cargar cartuchos de batería Makita. No lo utilice nunca con otros fines ni para

baterías de otros fabricantes.

• Cuando cargue un cartucho de batería que sea nuevo o que no haya sido utilizado durante un largo periodo de

tiempo, es posible que no acepte una carga completa hasta después de haberlo descargado completamente y

vuelto a cargar unas cuantas veces. (Batería Ni-MH solamente)

• Si la luz de carga parpadea en color rojo, la condición de la batería será como se indica abajo y es posible que la

carga no se inicie.

– Cartucho de batería de una herramienta recién utilizada o un cartucho de batería que ha sido dejado en un sitio

expuesto a la luz directa del sol durante largo tiempo.

– Cartucho de batería que ha sido dejado durante largo tiempo en un sitio expuesto a aire frío.

Cuando el cartucho de batería esté muy caliente, la carga comenzará después de que el ventilador de enfriamiento

instalado en el cargador enfríe el cartucho de batería. La carga comenzará después de que la temperatura del car-

tucho de batería alcance el grado al cual es posible cargar. Si la temperatura de la batería es de más de aproxima-

damente 70°C, podrán parpadear dos luces de carga en color rojo, y si es de aproximadamente 50°C – 70°C, podrá

parpadear una luz de carga en rojo.

• Si la luz de carga parpadea alternativamente en color verde y rojo, la batería no se podrá cargar. Los terminales del

cargador o de la batería estarán obstruidos con polvo o el cartucho de batería estropeado o dañado.

Sistema de enfriamiento

• Este cargador está equipado con un ventilador de enfriamiento para evitar el sobrecalentamiento de la batería, y así

poder sacarle a ésta el máximo rendimiento. Durante el enfriamiento se oye el sonido del ventilador, lo que significa

que no hay ningún problema en el cargador.

• En los siguientes casos parpadeará una luz amarilla de aviso.

– Problema en el ventilador de enfriamiento

– Batería no enfriada completamente, tal como, en el caso de que esté obstruida con polvo

La batería se puede cargar aunque esté parpadeando la luz amarilla. Pero en este caso tardará más tiempo en car-

garse.

Verifique el sonido del ventilador de enfriamiento, el orificio de ventilación de la batería, porque algunas veces

podrán estar obstruidos con polvo.

• Si la luz amarilla de aviso no parpadea, el sistema de enfriamiento estará bien aunque no se escuche el sonido del

ventilador de enfriamiento.

• Mantenga siempre limpios los orificios de ventilación del cargador y la batería.

• Si la luz amarilla de aviso parpadea con frecuencia, el cargador deberá ser enviado a que lo reparen o le hagan el

mantenimiento.

Carga de acondicionamiento

La carga de acondicionamiento puede alargar la vida útil de la batería buscando automáticamente la condición óptima

para la carga de la batería en cualquier situación.

La batería empleada en las siguientes condiciones repetidamente requerirá una “carga de acondicionamiento” para

evitar que su vida de servicio no se acorte rápidamente. En ese caso, se encenderá la luz amarilla.

1. Si la carga estando caliente.

2. Si la carga estando fría.

3. Si la recarga estando completamente cargada.

4. Si la descarga demasiado (si continúa utilizándola a pesar de tener poca potencia.)

El tiempo de carga de tal batería será más largo del normal.

10

Nota:

• Es posible que el tiempo de carga sea el doble que el indicado arriba como máximo debido a que la carga óptima se

selecciona en función de la temperatura (10°C (50°F) – 40°C (104°F)), las condiciones del cartucho de batería y la

carga de mantenimiento.

Tensión 9,6 V cc 12 V cc 14,4 V cc Capacidad (Ah) Tiempo de carga (minutos)

Número de celdas 8 10 12

Cartucho de

batería Ni-MH

— — — 1,7 Ah 20 min

BH9020A — — 2,0 Ah 20 min

— BH1220/C BH1420 2,0 Ah 15 min

— — — 2,7 Ah 20 min

BH9033A — — 3,3 Ah 30 min

— BH1233/C BH1433 3,3 Ah 22 min

Tensión 14,4 V cc 18 V cc 14,4 V cc 18 V cc Tiempo de carga (minutos)

Número de celdas 4 5 8 10

Cartucho de

batería Li-ion

BL1415 BL1815 — — 15 min

— — BL1430 BL1830 22 min

11

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi 446-8502 Japan

www.makita.com

884676H946

IDE

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

Cordless Hammer Driver Drill

Rotomartillo Atornillador

Inalámbrico

XPH12

IMPORTANT: Read Before Using.

IMPORTANTE: Lea antes de usar.

2ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: XPH12

Drilling capacities Masonry 13 mm (1/2")

Steel 13 mm (1/2")

Wood 38 mm (1/1/2")

Fastening capacities Wood screw 10 mm x 90 mm (3/8" x 3-1/2")

Machine screw M6 (1/4")

No load speed (RPM) High (2) 0 - 2,000 /min

Low (1) 0 - 500 /min

Blows per minute High (2) 0 - 30,000 /min

Low (1) 0 - 7,500 /min

Overall length 182 mm (7-1/8")

Rated voltage D.C. 18 V

Standard battery cartridge BL1815N, BL1820B BL1830, BL1830B, BL1840B,

BL1850B, BL1860B

Net weight 1.6 kg (3.5 lbs) 1.8 kg (4.0 lbs)

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsandbatterycartridgemaydifferfromcountrytocountry.

• Weight,withbatterycartridge,accordingtoEPTA-Procedure01/2003

General power tool safety warnings

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructionsmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Theterm"powertool"inthewarningsreferstoyour

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.Thereisanincreasedriskofelec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electric shock.

Personal Safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication.Amomentofinattentionwhileoperating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

willreducepersonalinjuries.

3. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

3ENGLISH

4. Remove any adjusting key or wrench before

turning the power tool on.Awrenchorakeyleft

attached to a rotating part of the power tool may

resultinpersonalinjury.

5. Do not overreach. Keep proper footing and

balance at all times.Thisenablesbettercontrol

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts.Looseclothes,jewel-

lery or long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application.Thecorrect

powertoolwilldothejobbetterandsaferatthe

rate for which it was designed.

2. Do not use the power tool if the switch does

not turn it on and off.Anypowertoolthatcannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer.Achargerthatissuitablefor

onetypeofbatterypackmaycreateariskofre

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help.Liquidejectedfromthebatterymaycause

irritation or burns.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

2. Follow instruction for lubricating and chang-

ing accessories.

3. Keep handles dry, clean and free from oil and

grease.

Cordless hammer driver drill safety

warnings

1. Wear ear protectors when impact drilling.

Exposuretonoisecancausehearingloss.

2. Use auxiliary handle(s), if supplied with the

tool.Lossofcontrolcancausepersonalinjury.

3. Hold power tool by insulated gripping sur-

faces, when performing an operation where

the cutting accessory may contact hidden

wiring. Cutting accessory contacting a "live"

wire may make exposed metal parts of the power

tool "live" and could give the operator an electric

shock.

4. Hold power tool by insulated gripping sur-

faces, when performing an operation where

the fastener may contact hidden wiring.

Fasteners contacting a "live" wire may make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

5. Always be sure you have a rm footing. Be

sure no one is below when using the tool in

high locations.

6. Hold the tool rmly.

7. Keep hands away from rotating parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not touch the bit or the workpiece immedi-

ately after operation; they may be extremely

hot and could burn your skin.

10. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

4ENGLISH

Symbols

Thefollowingsshowthesymbolsusedfortool.

volts

direct current

no load speed

revolutions or reciprocation per minute

number of blow

Important safety instructions for

battery cartridge

1.

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4.

If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tapeormaskoffopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. Follow your local regulations relating to dis-

posal of battery.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwillalso

void the Makita warranty for the Makita tool and charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoffyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

1

2

3

►1. Red indicator 2. Button 3. Battery cartridge

5ENGLISH

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Indicating the remaining battery

capacity

Only for battery cartridges with "B" at the end of the

model number

1

2

►1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the tool/battery is operated in a manner that

causes it to draw an abnormally high current, the tool

automatically stops without any indication. In this sit-

uation, turn the tool off and stop the application that

causedthetooltobecomeoverloaded.Thenturnthe

tool on to restart.

Overheat protection

When the tool/battery is overheated, the tool stops

automatically. In this situation, let the tool/battery cool

before turning the tool on again.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

NOTE: Overheat protection (for battery) will work only

with batteries with star marking.

1

►1. Star marking

6ENGLISH

Switch action

1

►1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopsifyoukeeppull-

ing the switch trigger for about 6 minutes.

Electric brake

Thistoolisequippedwithanelectricbrake.Ifthetool

consistently fails to quickly stop after the switch trigger

is released, have the tool serviced at a Makita service

center.

Lighting up the front lamp

1

►1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keeps on lighting while the switch trigger is being pulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

NOTE: When the tool is overheated, the tool stops

automaticallyandthelampstartsashing.Inthis

case,releasetheswitchtrigger.Thelampturnsoffin

one minute.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Reversing switch action

1

AB

►1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

Thistoolhasareversingswitchtochangethedirection

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Speed change

1

►1. Speed change lever

7ENGLISH

CAUTION: Always set the speed change lever

fully to the correct position. If you operate the

tool with the speed change lever positioned halfway

between the "1" side and "2" side, the tool may be

damaged.

CAUTION: Do not use the speed change lever

while the tool is running.Thetoolmaybedamaged.

Displayed

Number

Speed Torque Applicable

operation

1Low High Heavy load-

ing operation

2High Low Light loading

operation

Tochangethespeed,switchoffthetoolrst.Pushthe

speed change lever to display "2" for high speed or "1" for

low speed but high torque. Be sure that the speed change

lever is set to the correct position before operation.

If the tool speed is coming down extremely during the

operation with display "2", push the lever to display "1"

and restart the operation.

Selecting the action mode

CAUTION: Always set the ring correctly to

your desired mode mark. If you operate the tool

with the ring positioned halfway between the

mode marks, the tool may be damaged.

CAUTION: When you change the position

from " " to other modes, it may be a little dif-

culty to slide the action mode changing ring. In

this case, switch on and run the tool for a second

at the " " position, then stop the tool and slide

the ring to your desired position.

1

2

4

3

►1.Actionmodechangingring2.Adjustingring

3. Graduation 4.Arrow

Thistoolhasthreeactionmodes.

• Drilling mode (rotation only)

• Hammer drilling mode (rotation with

hammering)

• Screwdriving mode (rotation with clutch)

Selectonemodesuitableforyourwork.Turnthe

action mode changing ring and align the mark that you

selected with the arrow on the tool body.

Adjusting the fastening torque

1

2

4

3

►1.Actionmodechangingring2.Adjustingring

3. Graduation 4.Arrow

Thefasteningtorquecanbeadjustedin21levelsby

turningtheadjustingring.Alignthegraduationswiththe

arrow on the tool body. You can get the minimum fas-

tening torque at 1 and maximum torque at 21.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular applica-

tion.Thefollowingshowstheroughguideoftherela-

tionship between the screw size and graduation.

Graduation 12345678910 11 12 13 14 15 16 17 18 19 20 21

Machine screw M4 M5 M6

Wood

screw

Soft wood

(e.g. pine)

–ɸ3.5 x 22 ɸ4.1x 38 –

Hard wood

(e.g. lauan)

–ɸ3.5 x 22 ɸ4.1x 38 –

8ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

drill bit

Optional accessory

1

3

2

►1. Sleeve 2. Close 3. Open

Turnthesleevecounterclockwisetoopenthechuck

jaws.Placethedriverbit/drillbitinthechuckasfar

asitwillgo.Turnthesleeveclockwisetotightenthe

chuck.Toremovethedriverbit/drillbit,turnthesleeve

counterclockwise.

Installing hook

1

3

2

►1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

the hook, insert it into a groove in the tool housing on

eithersideandthensecureitwithascrew.Toremove,

loosen the screw and then take it out.

Installing driver bit holder

Optional accessory

1

2

►1. Driver bit holder 2. Driver bit

Fit the driver bit holder into the protrusion at the tool foot

on either right or left side and secure it with a screw.

When not using the driver bit, keep it in the driver bit

holders. Driver bits 45 mm-long (1-3/4") can be kept

there.

OPERATION

CAUTION: Always insert the battery cartridge

all the way until it locks in place. If you can see the

red indicator on the upper side of the button, it is not

locked completely. Insert it fully until the red indicator

cannot be seen. If not, it may accidentally fall out of

thetool,causinginjurytoyouorsomeonearound

you.

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

Holdthetoolrmlywithonehandonthegripandthe

other hand on the bottom of the battery cartridge to

control the twisting action.

La page charge ...

Makita XT328M-XRM04B-XAG03Z Mode d'emploi

Makita XT328M-XRM04B-XAG03Z Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents