Generac 7019 Le manuel du propriétaire

MODEL:________________________

SERIAL:________________________

DATE PURCHASED:______________

Register your Generac product at:

WWW.GENERAC.COM

1-888-GENERAC

(1-888-436-3722)

SAVE THIS MANUAL FOR FUTURE REFERENCE

Power Washer

Owner’s Manual

MODEL:________________________

SERIAL:________________________

DATE PURCHASED:______________

Register your Generac product at:

WWW.GENERAC.COM

1-888-GENERAC

Table of Contents

Section 1 Introduction and Safety

Introduction ..................................... 1

Safety Rules .................................... 1

Safety Symbols and Meanings ........ 2

Section 2 General Information

and Setup

Know Your Power Washer .............. 3

Emissions Information ..................... 3

Remove Contents from Carton ....... 3

Assembly ......................................... 3

Add Engine Oil ................................ 4

Fuel ................................................. 4

Water Supply ................................... 5

Connect Water Supply .................... 5

Connect High-Pressure Hose

and Lance ....................................... 5

Spray Gun ....................................... 6

Detergent Tank (if equipped) .......... 6

Nozzles ........................................... 6

Section 3 Operation

Operation and Use Questions ......... 7

Before Starting Engine .................... 7

Prepare Power Washer for Use ...... 7

Power Washer Placement for Use ..... 7

Transporting/Tipping of the Unit ......... 7

Power Washer Start-Up .................. 7

Power Washer Shut Down .............. 8

Apply Detergent .............................. 8

Rinsing ............................................ 9

Clean Detergent Siphoning Tube ....9

After Each Use ‘ .................................. 9

Automatic Cool Down System

(Thermal Relief) ...............................9

Section 4 Maintenance and

Troubleshooting

Maintenance Recommendations ...10

Maintenance Schedule ..................10

Pump Oil ........................................10

Preventive Maintenance ................10

Inspect and Clean Inlet Screen ........ 10

Inspect High-Pressure Hoses ........... 10

Inspect Detergent Siphoning Tube ... 10

Inspect Spray Gun ............................ 10

Nozzle Maintenance ......................... 11

Engine Maintenance ......................11

Engine Oil Recommendations .......... 11

Inspect Engine Oil Level ................... 11

Change Engine Oil ........................... 12

Air Filter ............................................ 12

Service Spark Plug ........................12

Inspect Engine Spark ....................... 12

Inspect Muffler And Spark Arrestor .. 12

Inspect Spark Arrestor Screen

(if equipped) ..................................... 13

Storage ..........................................13

General ............................................. 13

Prepare Fuel System for Storage ..... 13

Prepare Engine for Storage .............. 13

Change Oil ....................................... 14

Prepare Pump for Storage ............... 14

(000004)

WARNING

California Proposition 65. Engine exhaust and some

of its constituents are known to the state of California

to cause cancer, birth defects, and other reproductive

harm.

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

Introduction and Safety

Owner’s Manual for Power Washer 1

Section 1 Introduction and Safety

Introduction

Thank you for purchasing a Generac Power

Systems Inc. product. This unit has been

designed to provide high performance,

efficient operation, and years of use when

maintained properly.

Read this manual thoroughly and understand

all of the instructions, cautions, and warnings

before using this equipment. If any section of

the manual is not understood, contact your

nearest independent authorized service

dealer or contact Generac Customer Service

at 1-888-GENERAC (1-888-436-3722), or

www.generac.com with any questions or

concerns.

The owner is responsible for proper

maintenance and safe use of the equipment.

Before operating, servicing or storing this

power washer:

• Study all warnings in this manual and on

the product carefully.

• Become familiar with this manual and the

unit before use.

• Refer to the Assembly section of the

manual for instructions on final assembly

procedures. Follow the instructions

completely.

Save these instructions for future reference.

ALWAYS supply this manual to any individual

that will use this machine.

THE INFORMATION CONTAINED HEREIN

WAS BASED ON MACHINES IN

PRODUCTION AT THE TIME OF

PUBLICATION. GENERAC RESERVES THE

RIGHT TO MODIFY THIS MANUAL AT ANY

TIME.

Safety Rules

The manufacturer cannot anticipate every

possible circumstance that might involve a

hazard. The warnings in this manual, and on

tags and decals affixed to the unit are,

therefore, not all inclusive. If using a

procedure, work method or operating

technique that the manufacturer does not

specifically recommend, verify that it is safe

for others. Also make sure the procedure,

work method or operating technique utilized

does not render the equipment unsafe.

Throughout this publication, and on tags and

decals affixed to the power washer, DANGER,

WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions

about a particular operation that may be

hazardous if performed incorrectly or

carelessly. Observe them carefully. Their

definitions are as follows:

NOTE:

Notes contain additional information important

to a procedure and will be found within the

regular text of this manual.

These safety warnings cannot eliminate the

hazards that they indicate. Common sense

and strict compliance with the special

instructions while performing the action or

service are essential to preventing accidents.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Introduction and Safety

2 Owner’s Manual for Power Washer

Safety Symbols and Meanings

Asphyxiation. Running engines produce

carbon monoxide, a colorless, odorless,

poisonous gas. Carbon monoxide, if not

avoided, will result in death or serious injury.

(000103)

DANGER

(000104)

DANGER

Electrocution. Water contact with a power

source, if not avoided, will result in death

or serious injury.

(000106)

DANGER

Fluid Injection. This machine produces

high-pressure fluid streams that can pierce

skin. Fluid injection will result in death or

serious injury.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

(000101)

WARNING

Vision Loss. Eye goggles are required to be

worn when using this machine. Failure to wear

eye goggles could result in permanent

vision loss.

(000107)

WARNING

Hearing Loss. Hearing protection is

recommended when using this machine.

Failure to wear hearing protection could

result in permanant hearing loss.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

(000109)

WARNING

Risk of Fire. Verify machine has properly

cooled before installing cover and storing

machine. Hot surfaces could result in fire.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and

appendages away from moving parts. Failure

to do so could result in death or serious injury.

(000112)

WARNING

Risk of Falling. Use of machine creates wet

areas and trip hazards. Be aware of work area

conditions. A fall could result in death

or serious injury.

(000114)

WARNING

Risk of Falling. Do not use this machine or

any components on elevated surfaces.

Doing so can result in a fall, serious injury,

or death.

(000113)

WARNING

Recoil Hazard. Recoil could retract unexpectedl

y

if water pressure is not properly relieved from

pump, creating kickback. Kickback could result

in death or serious injury.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000115)

WARNING

Moving Parts. Do not wear jewelry when

starting or operating this product. Wearing

jewelry while starting or operating this product

could result in death or serious injury.

(000117)

WARNING

Do not aim spray gun at people, animals,

electrical devices,or fragile items.

Keep out of reach of children.

Death or serious injury could result.

WARNING

Environmental Hazard. Always recycle batteries at an

official recycling center in accordance with all local

laws and regulations. Failure to do so could result in

environmental damage, death or serious injury.

(000228)

(000244)

WARNING

Personal Injury / Equipment Damage. Place wand in

holster and verify that handle is locked into place

before moving. Failure to do so could result in death,

serious injury, or equipment damage.

General Information and Setup

Owner’s Manual for Power Washer 3

Section 2 General Information and Setup

Know Your Power Washer

Read this manual thoroughly before

assembling and operating this unit. Save this

manual for future and immediate reference.

Replacement owner’s manuals are available

at www.generac.com.

Emissions Information

The United States Environmental Protection

Agency (US EPA) (and California Air

Resources Board (CARB), for engines/

equipment certified to California standards)

requires that this engine/equipment complies

with exhaust and evaporative emissions

standards. Locate the emissions compliance

decal on the engine to determine applicable

standards. For emissions warranty

information, please reference the included

emissions warranty. It is important to follow

the maintenance specifications in the manual

to ensure that the engine complies with the

applicable emissions standards for the

duration of the product’s life.

Remove Contents from Carton

1. Open carton completely by cutting each

corner from top to bottom.

2. Remove and verify carton contents prior to

assembly. Carton contents should contain

one each of the following:

•Main Unit

• Handle Assembly

• High-pressure Hose

• Siphon Hose & Filter

• Spray Gun

•Lance

•Oil

• Hose Hook Wireform

• Parts Bag (includes):

– Owner’s Manual

– Owner’s Registration Card

– Bag of Colored Nozzles

– Funnel

3. Call Generac Customer Service at 1-888-

GENERAC (1-888-436-3722) with the unit

model and serial number for any missing

carton contents.

4. Record model, serial number, and date of

purchase on front cover of this manual.

Assembly

Call Generac Customer Service at 1-888-

GENERAC (1-888-436-3722) for any

assembly issues or concerns. Please have

model and serial number available.

1. See Figure 2-1. Place handle (A) onto

handle supports (B). Push in latch buttons

(C) and allow handle to slide into position.

Button will lock handle into place.

Figure 2-1. Insert Handle

NOTE: It may be necessary to move the

handle supports from side to side in order to

align the handle so it will slide over the handle

supports.

2. See Figure 2-2. Install hose hook.

Figure 2-2.Install Hose Hook

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

001413

A

B

C

001412

General Information and Setup

4 Owner’s Manual for Power Washer

3. See Figure 2-3. Insert and snap nozzles

into spaces provided in handle.

Figure 2-3. Insert Nozzles

4. See Figure 2-4. Attach siphon tube to

siphon tube connection (A).

Figure 2-4. Attach Siphon Tube

Add Engine Oil

Unit is shipped with no oil in the engine.

Add engine oil before starting. See Engine Oil

Recommendations.

1. Place power washer on a level surface.

2. Verify oil fill area is clean.

3. Remove oil fill cap and wipe dipstick clean.

Figure 2-5. Remove Dipstick

4. Add recommended engine oil.

NOTE: Some units have more than one oil fill

location. It is only necessary to use one oil fill

point.

5. Thread dipstick into oil filler neck. Oil level

is checked with dipstick fully inserted.

6. See Figure 2-6. Remove dipstick and verify

oil level is within safe operating range.

Figure 2-6. Safe Operating Range

7. Install oil fill cap/dipstick and hand-tighten.

Fuel

Fuel requirements are as follows:

• Clean, fresh, unleaded gasoline.

• Minimum rating of 87 octane/87 AKI (91

RON).

• Up to 10% ethanol (gasohol) is acceptable.

• DO NOT use E85.

• DO NOT use a gas oil mix.

• DO NOT modify engine to run on alternate

fuels.

• Add a fuel stabilizer prior to storing.

1. Verify unit is OFF and cooled for a

minimum of two minutes prior to fueling.

2. Place unit on level ground in a well

ventilated area.

3. See Figure 2-7. Clean area around fuel

cap and remove cap slowly.

4. Slowly add recommended fuel. Do not

overfill

.

Figure 2-7. Add Recommended Fuel

5. Install fuel cap.

NOTE: Allow spilled fuel to evaporate before

starting unit.

001411

000114

A

000115

000116

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

000117

General Information and Setup

Owner’s Manual for Power Washer 5

Water Supply

NOTE: DO NOT run unit without sufficient

water supply. Failure to follow water supply

requirements will void unit warranty.

Water supply must meet the following

requirements:

• DO NOT siphon standing water for the

water supply.

• Water temperature must be less than

100°F (38ºC).

• Water supply hose length must not exceed

50 ft (15.2 m).

• Water must be greater than 3.8 gallons per

minute (17.3 liters per minute) and no less

than 30 psi (206.8 kPa).

• DO NOT use a one-way valve, vacuum

breaker, or check valve in any part of the

water supply.

Connect Water Supply

1. Remove and discard shipping cap from

the pump water inlet.

2. Run water supply for 30 seconds prior to

connection to eliminate debris.

3. See Figure 2-8. Inspect inlet screen for

debris. Clean screen or replace as

necessary. DO NOT run power washer if

inlet screen is damaged or missing.

Figure 2-8. Inspect Inlet Screen

4. See Figure 2-9. Connect water supply

hose to pump water inlet and hand-

tighten.

.

Figure 2-9. Connect Water Supply Hose

Connect High-Pressure Hose

and Lance

1. See Figure 2-10. Connect lance to spray

gun and hand-tighten.

Figure 2-10. Connect Lance

2. Place spray gun and nozzle extension into

spray gun holder.

3. See Figure 2-11. Connect high-pressure

hose to pump and hand-tighten.

Figure 2-11. Connect High-Pressure Hose

to Pump

4. See Figure 2-12. Connect high-pressure

hose to base of spray gun and hand-

tighten.

Figure 2-12. Connect High-Pressure Hose

to Spray Gun

001563

000119

000120

000121

000122

General Information and Setup

6 Owner’s Manual for Power Washer

Spray Gun

Become familiar with spray gun trigger and

locking system prior to use.

1. See Figure 2-13. With unit OFF, hold spray

gun and squeeze trigger to learn how

trigger mechanism and locking system can

be activated and deactivated.

Figure 2-13. Spray Gun (typical)

2. Turn ON the water, and squeeze the

trigger to purge the pump system of air.

3. Verify spray gun is OFF with lock engaged

before starting power washer.

Detergent Tank (if equipped)

Power washer is shipped with siphoning tube

and cap.

1. See Figure 2-14. Insert siphoning tube

through hole in cap.

Figure 2-14. Siphoning Tube and Cap

2. Insert siphoning tube into detergent and

snap siphoning tube cap onto detergent

tank.

Nozzles

1. Select correct nozzle for task.

2. See Figure 2-15. Pull back quick–connect

collar and install nozzle.

3. Release quick-connect collar to secure

nozzle.

4. Verify nozzle is locked in place.

Figure 2-15. Insert Nozzle

Blast Pressure Nozzle (Red)

MAXIMUM - Higher pressure and lower flow

for stubborn or hard to reach surface such as

second story surfaces, paint removal, oil

stains, rust removal or other stubborn

substances (tar, gum, grease, wax, etc.).

Clean Pressure Nozzle (Green)

GENERAL - Medium pressure and medium

flow for most all purpose cleaning such as

home siding, brick patios, wood decks,

driveways and sidewalks, garage floors, etc.

Wash Pressure Nozzle (White)

DELICATE - Lower pressure and higher flow

for gentle cleaning of cars/trucks, boats, RV’s,

patio furniture, lawn equipment, etc.

Detergent Nozzle (Black)

DETERGENT ONLY (BLACK), Only use

power washer safe detergents/soaps to help

break down stubborn dirt and grime on a

variety of surfaces.

000123

001487

000125

001396

001398

001399

001400

Operation

Owner’s Manual for Power Washer 7

Section 3 Operation

Operation and Use Questions

Call Generac Customer Service at 1-888-

GENERAC (1-888-436-3722) with questions

or concerns about unit operation and

maintenance.

Before Starting Engine

Unit is shipped with no oil in the

crankcase. Add engine oil before starting.

See Engine Oil Recommendations.

1. Verify engine oil level is correct.

2. Verify fresh fuel level is correct.

3. Verify all fittings and couplers are properly

secured.

4. Verify sufficient water supply is properly

connected.

5. Verify thermal relief valve is rotated and

open to ground.

6. Verify unit is secure on level ground, with

proper clearance and is in a well ventilated

area.

Prepare Power Washer for Use

1. Place unit on level ground, within the

specified clearance required.

2. Connect appropriate water supply.

Power Washer Placement for Use

It is a violation of California Public Resource

Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust

system is equipped with a spark arrestor, as

defined in Section 4442, maintained in

effective working order. Other states or federal

jurisdictions may have similar laws.

Only operate power washer outdoors in a well

ventilated area. Never operate power washer

indoors, or in a confined space. Be aware of

building openings and ventilation systems

where exhaust may enter during use.

• Verify power washer is placed on level

ground to avoid tipping during operation.

• Only use the unit outdoors. Verify exhaust

gas does not enter a confined area through

windows, doors, ventilation intakes.

•See Figure 3-1. Keep at least 5 ft (1.5 m) of

clearance on all sides of power washer

including overhead from dwellings and

combustibles, when in use.

Figure 3-1. Five Feet of Minimum

Clearance

Transporting/Tipping of the Unit

Do not operate, store or transport the unit at

an angle greater than 15 degrees.

Power Washer Start-Up

NOTE: DO NOT run power washer without a

sufficient water supply turned ON. Damage to

equipment resulting from failure to follow this

instruction will void warranty.

1. Connect a sufficient water supply.

2. See Figure 3-2. Move fuel valve lever (B)

to ON position.

3. Move choke lever (A) to CLOSED position.

Figure 3-2. Fuel Valve and Choke

NOTE: For warm engine, verify choke lever is

in OPEN position.

Asphyxiation. Running engines produce

carbon monoxide, a colorless, odorless,

poisonous gas. Carbon monoxide, if not

avoided, will result in death or serious injury.

(000103)

DANGER

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

001564

(000244)

WARNING

Personal Injury / Equipment Damage. Place wand in

holster and verify that handle is locked into place

before moving. Failure to do so could result in death,

serious injury, or equipment damage.

000127

A

B

Operation

8 Owner’s Manual for Power Washer

4. See Figure 3-3. Turn engine switch ON.

Figure 3-3. Engine Switch

5. Relieve spray gun pressure.

6. Place foot on unit to secure unit from

movement when pulling recoil.

7. See Figure 3-4. Firmly grasp the recoil

handle. Pull slowly until resistance is felt.

Then pull rapidly to start engine.

After engine-start attempt, if engine fails to

run, point spray gun in safe direction, and

squeeze spray gun trigger to release high

pressure.

Figure 3-4. Engine Recoil

8. Return recoil handle slowly. DO NOT let

recoil snap back against recoil housing.

9. See Figure 3-2. When engine starts, slowly

move choke lever (A) to OPEN position as

engine warms. If engine falters, move

choke lever to CLOSE position, then to

OPEN position.

• If engine fails to start after six pulls, move

choke lever (A) to “OPEN” position, and

repeat steps 6 through 9.

Power Washer Shut Down

IMPORTANT: Spray gun traps high-pressure

water, even when engine is stopped and water

is disconnected. Always point spray gun in

safe direction, and squeeze spray gun trigger

to release high-pressure. Engage trigger lock

when not in use.

1. Release spray gun trigger.

2. Turn engine switch OFF.

3. Turn water supply OFF.

4. Squeeze spray gun trigger and release

high-pressure water.

5. Engage trigger lock.

Apply Detergent

NOTE: DO NOT use caustic liquid with power

washer. Use ONLY power washer safe

detergents. Follow all manufacturer's

instructions on the detergent label.

Apply detergent as follows:

1. Verify black detergent nozzle is installed.

2. Open detergent tank cap, if equipped.

3. Prepare detergent solution as required by

job.

OFF

ON

000128

(000101)

WARNING

Vision Loss. Eye goggles are required to be

worn when using this machine. Failure to wear

eye goggles could result in permanent

vision loss.

(000113)

WARNING

Recoil Hazard. Recoil could retract unexpectedly

if water pressure is not properly relieved from

pump, creating kickback. Kickback could result

in death or serious injury.

(000117)

WARNING

Do not aim spray gun at people, animals,

electrical devices,or fragile items.

Keep out of reach of children.

Death or serious injury could result.

000129

(000106)

DANGER

Fluid Injection. This machine produces

high-pressure fluid streams that can pierce

skin. Fluid injection will result in death or

serious injury.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

(000106)

DANGER

Fluid Injection. This machine produces

high-pressure fluid streams that can pierce

skin. Fluid injection will result in death or

serious injury.

(000106)

DANGER

Fluid Injection. This machine produces

high-pressure fluid streams that can pierce

skin. Fluid injection will result in death or

serious injury.

(000117)

WARNING

Do not aim spray gun at people, animals,

electrical devices,or fragile items.

Keep out of reach of children.

Death or serious injury could result.

Operation

Owner’s Manual for Power Washer 9

4. Depending on model, insert filter on end of

siphoning tube through hole in cap

(supplied).

NOTE: Verify siphoning tube and filter remain

fully submerged in detergent while in use.

NOTE: When inserting siphon tube into

detergent tank, route tube to prevent muffler

contact. Contact with muffler while in use can

damage detergent siphoning tube.

5. Verify black detergent nozzle is installed.

NOTE: Detergent cannot be applied with high-

pressure nozzle (White, Green or Red). Only

use black nozzle with detergent.

6. Start engine.

7. Apply detergent to a dry surface. Start at

lower portion of area to be washed and

work upward using long, even,

overlapping strokes.

IMPORTANT: Flush the detergent siphoning

system after each use. Contact an authorized

dealer or qualified service center with

questions.

Rinsing

1. Remove black detergent nozzle from

lance.

2. Select and install desired high-pressure

nozzle.

3. Point spray gun in safe direction and

squeeze trigger to flush remaining

detergent from system.

4. Keep spray gun a safe distance from area

you plan to spray.

5. Spray gun may kick back when using high

pressure spray. To avoid injury, firmly

grasp spray gun with both hands.

6. Apply a high-pressure spray to a small

area and then inspect surface for damage.

If no damage is found, continue rinsing.

7. Start at top of area to be rinsed, working

down with same overlapping strokes as

used for cleaning.

Clean Detergent Siphoning

Tube

Flush detergent siphoning tube after each use

before stopping the engine.

1. Place detergent siphoning tube/filter in

bucket of clean water.

2. Remove high-pressure nozzle from lance.

3. Select and install black detergent nozzle.

4. Flush for 1-2 minutes.

5. Shut engine OFF.

6. Point spray gun in a safe direction,

squeeze spray gun trigger to release

retained high water pressure. Engage

trigger lock.

After Each Use

DO NOT allow water to remain in unit for long

periods of time. Sediments or minerals can

deposit on pump parts and freeze pump.

Follow these procedures after every use:

1. Shut engine OFF.

2. Turn water supply OFF.

3. Point spray gun in a safe direction, and

squeeze trigger to relieve trapped

pressure.

4. Let engine cool.

5. Disconnect hoses from spray gun and

high-pressure outlet on pump. Drain water

from hoses, spray gun, and lance. Use a

rag to wipe off components.

6. Pull recoil handle approximately six times

to remove remaining liquid from pump.

7. Switch fuel valve to OFF.

8. Store unit in a clean, dry area.

NOTE: If storing for more than 30 days, see

Storage.

Automatic Cool Down System

(Thermal Relief)

When power washer runs for 3-5 minutes

without spray gun activation, circulating water

in pump can reach a temperature sufficient to

engage the thermal relief system. The pump is

cooled by discharging water onto ground.

(000112)

WARNING

Risk of Falling. Use of machine creates wet

areas and trip hazards. Be aware of work area

conditions. A fall could result in death

or serious injury.

(000114)

WARNING

Risk of Falling. Do not use this machine or

any components on elevated surfaces.

Doing so can result in a fall, serious injury,

or death.

Maintenance and Troubleshooting

10 Owner’s Manual for Power Washer

Section 4 Maintenance and Troubleshooting

Maintenance Recommendations

Regular maintenance will improve

performance and extend engine/equipment

life. Generac Power Systems, Inc.

recommends that all maintenance work be

performed by an Independent Authorized

Service Dealer (IASD). Regular maintenance,

replacement or repair of the emissions control

devices and systems may be performed by

any repair shop or person of the owner’s

choosing. However, to obtain emissions

control warranty service free of charge, the

work must be performed by an IASD. See the

emissions warranty.

Power washer warranty does not cover items

subjected to operator abuse or negligence. To

receive full warranty value, operator must

maintain power washer as instructed in this

manual, including proper storage as detailed

in Storage.

NOTE: Call 1-888-GENERAC (1-888-436-

3722) with questions about component

replacement.

NOTE: All required service and adjustments

should be each season, as detailed in

Maintenance Schedule.

Maintenance Schedule

Follow maintenance schedule intervals,

whichever occurs first according to use.

NOTE: Adverse conditions will require more

frequent service.

* Clean if clogged. Replace if perforated or torn.

** Service more often under dirty or dusty

conditions.

Pump Oil

DO NOT attempt any oil maintenance on

pump. Pump is lubricated and sealed at

factory. No additional maintenance is required

for life of pump.

Preventive Maintenance

Dirt or debris can cause improper operation

and equipment damage. Clean power washer

daily or before each use. Keep area around

and behind muffler free from combustible

debris. Inspect all cooling air openings on

power washer.

• Use a damp cloth to wipe exterior surfaces

clean.

• DO NOT insert any objects through cooling

air openings.

• Use a soft bristle brush to loosen caked on

dirt, oil, etc.

• Use a vacuum to pick up loose dirt and

debris.

Inspect and Clean Inlet Screen

Inspect inlet screen on pump water inlet.

Clean clogged screen and replace screen if

damaged.

Inspect High-Pressure Hoses

High-pressure hoses can develop leaks from

wear, kinking, or abuse. Inspect hoses before

each use. Inspect for cuts, leaks, abrasions,

bulging, and damage or movement of

couplings. If these conditions exist, replace

hose immediately.

NOTE: DO NOT repair high-pressure hose.

Replace with hose that meets or exceeds

maximum pressure rating of unit.

Inspect Detergent Siphoning Tube

Inspect filter on detergent tube and clean if

clogged. Tube should fit tightly on barbed

fitting. Examine tube for leaks or tears.

Replace filter or tube if either is damaged.

Inspect Spray Gun

NOTE: Replace spray gun immediately if it

fails any test steps.

Figure 4-1.Test Spray Gun (typical)

1. Verify spray gun hose connection is

secure.

2. Squeeze and release trigger.

NOTE: Trigger should spring back into place

and lock when released.

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Inspect/clean water inlet screen*

Inspect high-pressure hose

Inspect detergent siphoning tube/filter

Inspect spray gun and assembly for leaks

Clean debris

Inspect engine oil level

Every 20 Hours or Every Season

Change engine oil**

Every 50 Hours or Every Season

Inspect/clean air cleaner filter**

Inspect muffler and spark arrestor*

Every 100 Hours or Every Season

Service spark plug

000123

Maintenance and Troubleshooting

Owner’s Manual for Power Washer 11

Nozzle Maintenance

A pulsing sensation felt when squeezing spray

gun trigger may be caused by excessive

pump pressure. Typical causes of excessive

pump pressure are nozzle clog or restriction.

Immediately clean nozzle as follows:

1. Turn engine and water supply OFF.

NOTE: Keep high-pressure hose connected

to pump and spray gun while system is

pressurized.

2. Relieve spray gun water pressure.

3. Remove nozzle from lance.

4. See Figure 4-2. Use a paper clip to remove

debris.

5. See Figure 4-3. Remove lance from spray

gun and back flush thoroughly.

6. Install nozzle on lance.

7. Install lance on spray gun.

Figure 4-2.Remove Debris

Figure 4-3.Back Flush Lance

8. Verify hose is connected to pump water

inlet, and high-pressure hose is connected

to spray gun and pump.

9. Turn water ON.

10. Start engine.

11. Test power washer by operating with each

quick connect nozzle.

Engine Maintenance

Engine Oil Recommendations

To maintain the product warranty, the engine oil

should be serviced in accordance with the

recommendations of this manual. For your

convenience, Generac Maintenance Kits are

available that include engine oil, oil filter, air

filter, spark plug(s), a shop towel and funnel.

These kits can be obtained from an

Independent Authorized Service Dealer (IASD).

Only high-quality detergent oils classified for

service SJ or higher are recommended. DO

NOT use special additives.

Climate determines proper engine oil

viscosity. See chart to select correct viscosity.

Figure 4-4. Oil Viscosity

* Below 50°F (10°C) use of SAE 30 will result

in hard start.

** Above 80°F (27°C) use of 10W30 may

cause increased oil consumption. Inspect oil

level more frequently.

Inspect Engine Oil Level

Inspect engine oil level prior to each use, or

every 8 hours of operation.

1. Place power washer on a level surface.

2. Clean area around oil fill.

3. See Figure 4-5. Remove oil fill cap and

wipe dipstick clean.

Figure 4-5. Engine Oil Fill

4. See Figure 4-6. Screw dipstick into filler

neck.Verify proper oil level on dipstick.

Figure 4-6. Oil Level

5. Add recommended engine oil as

necessary.

6. Replace oil fill cap and hand-tighten.

NOTE: Some units have more than one oil fill

location. It is only necessary to use one oil fill

point.

(000106)

DANGER

Fluid Injection. This machine produces

high-pressure fluid streams that can pierce

skin. Fluid injection will result in death or

serious injury.

000109

000131

000130

SAE 30*

5W-30

10W-30**

000115

000116

Maintenance and Troubleshooting

12 Owner’s Manual for Power Washer

Change Engine Oil

When using power washer under extreme,

dirty, dusty conditions, or in extremely hot

weather, change oil more frequently.

NOTE: Don’t pollute. Conserve resources.

Return used oil to collection centers.

Change oil while engine is still warm from

running, as follows:

1. Place power washer on a level surface.

2. Disconnect the spark plug wire from the

spark plug and place the wire where it

cannot contact spark plug.

3. Clean area around oil fill, and oil drain

plug.

4. Remove oil fill cap.

5. See Figure 4-7. Remove oil drain plug (A)

and drain oil completely into a suitable

container.

6. Install oil drain plug and tighten securely.

7. See Figure 4-6. Slowly pour oil into oil fill

opening until oil level is between L and H

marks on dipstick. DO NOT overfill.

8. Install oil fill cap, and finger tighten.

9. Wipe up any spilled oil.

10. Properly dispose of oil in accordance with

all applicable regulations.

Figure 4-7.Oil Drain Plug

Air Filter

Engine will not run properly and may be

damaged if run with a dirty air cleaner. Service

air cleaner more frequently in dirty or dusty

conditions.

To service air cleaner:

1. Remove air cleaner cover.

2. Remove filter element(s).

3. Inspect filter element(s) and replace if

damaged. To order replacements, contact

Generac Customer Service at 1-888-

GENERAC (888-436-3722) for the name

of your nearest Independent Authorized

Service Dealer.

4. Clean foam filter element in warm soapy

water. Rinse, and allow to dry thoroughly.

Dip in clean engine oil and squeeze out

excess oil.

5. Tap paper filter element several times on

hard surface to remove dirt. Compressed

air (not exceeding 30 psi (207 kPa) can

also be used to blow through filter element

from the inside.

6. Use a clean, damp cloth to wipe dirt from

inside air cleaner cover.

7. Put cleaned or new filter element(s) in

place. Verify gasket is in place (if

equipped).

8. Install air cleaner cover. Tighten air

cleaner screws or fasteners securely.

Service Spark Plug

To service spark plug:

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. See Figure 4-8. Inspect electrode gap with

wire feeler gauge and replace spark plug if

gap (A) is not within specification listed on

Product Specifications Sheet.

Figure 4-8. Spark Plug

NOTE: Replace spark plug if electrodes are

pitted, burned or porcelain is cracked. Use

ONLY recommended replacement plug. See

Specifications.

4. Install spark plug finger tight, and tighten

an additional 3/8 to 1/2 turn using spark

plug wrench.

Inspect Engine Spark

1. Disconnect spark plug wire from spark

plug.

2. Secure spark plug wire where it cannot

contact spark plug.

3. Test spark plug with approved spark plug

tester.

NOTE: DO NOT inspect for spark with spark

plug removed.

Inspect Muffler And Spark Arrestor

NOTE:

It is a violation of California Public

Resource Code, Section 4442, to use or

operate the engine on any forest-covered,

brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark

arrestor, as defined in Section 4442, maintained

in effective working order. Other states or

federal jurisdictions may have similar laws.

001556

A

000134a

(000102)

WARNING

Accidental Start-up. Disconnect spark plug wire

when working on unit. Failure to do so could result

in death or serious injury.

Maintenance and Troubleshooting

Owner’s Manual for Power Washer 13

NOTE: Call 1-888-GENERAC (1-888-436-

3722) with questions about component

replacement.

NOTE: Use ONLY original equipment

replacement parts.

Inspect muffler for cracks, corrosion, or other

damage. Remove spark arrestor, if equipped,

inspect for damage or carbon blockage. If

replacement parts are required.

Inspect Spark Arrestor Screen

(if equipped)

1. See Figure 4-9. Loosen fasteners (A) and

remove heat shield from muffler.

2. See Figure 4-10. Loosen fasteners (B) and

remove spark arrestor from muffler.

3. Inspect spark arrestor. Replace if torn,

perforated or otherwise damaged.

• Spark Arrestor P/N 0K1851

4. If screen is not damaged, clean it with a

commercial solvent and replace.

Figure 4-9. Heat Shield Fasteners

Figure 4-10. Spark Arrestor Fasteners

Storage

General

• DO NOT place a storage cover on a hot

power washer. Allow unit to cool to room

temperature before storage.

• DO NOT store fuel from one season to

another unless properly treated.

• Replace fuel container if rust is present.

Rust in fuel will cause fuel system

problems.

• Cover unit with a suitable protective,

moisture resistant cover.

• Store unit in a clean and dry area.

• Always store power washers and fuel away

from heat and ignition sources.

Prepare Fuel System for Storage

Fuel stored over 30 days can go bad and

damage fuel system components. Keep fuel

fresh, use fuel stabilizer.

If fuel stabilizer is added to fuel system,

prepare and run engine according to Power

Washer Start-Up. Run engine for 2 minutes to

circulate stabilizer throughout fuel system.

Adequately prepared fuel can be stored up to

24 months.

NOTE: If fuel has not been treated with fuel

stabilizer, it must be drained into an approved

container. Run engine until it stops from lack

of fuel. Use of fuel stabilizer in fuel storage

container is recommended to keep fuel fresh.

Prepare Engine for Storage

1. Change engine oil.

2. Remove spark plug.

3. Pour a tablespoon (5-10cc) of clean

engine oil or spray a suitable fogging

agent into cylinder.

4. Pull starter recoil several times to

distribute oil in cylinder.

5. Install spark plug.

6. Pull recoil slowly until resistance is felt.

This will close valves so moisture cannot

enter engine cylinder. Gently release

recoil.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

000135

A

000136

B

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

(000109)

WARNING

Risk of Fire. Verify machine has properly

cooled before installing cover and storing

machine. Hot surfaces could result in fire.

Maintenance and Troubleshooting

14 Owner’s Manual for Power Washer

Change Oil

Change engine oil before storage. See

Change Engine Oil.

Prepare Pump for Storage

NOTE: If not using power washer for more

than 30 days, prepare engine and pump for

storage.

Protect unit from freezing temperatures.

Failure to do so will permanently damage

pump and render unit inoperable. Freeze

damage is not covered under warranty.

Protect unit from freezing temperatures as

follows:

1. Shut engine OFF.

2. Turn fuel valve to OFF.

3. Turn water supply OFF.

4. Point spray gun in a safe direction, and

squeeze trigger to relieve trapped

pressure.

5. Let engine cool.

6. Disconnect hoses from spray gun and

high-pressure outlet on pump. Drain water

from hoses, spray gun, and lance. Use a

rag to wipe off components.

7. Empty pump of all remaining liquids.

8. Pull recoil handle approximately six times

to remove remaining liquid from pump.

9. Winterize pump with Generac Pump

Shield™ (P/N 0L2414). This minimizes

freeze damage and lubricates pistons and

seals.

NOTE: If Generac Pump Shield™ is not

available, connect a 3 ft (1 m) section of

garden hose to water inlet adapter. Pour RV-

antifreeze (alcohol free antifreeze) into hose.

Pull recoil handle twice. Disconnect hose.

Store unit in a clean and dry area.

Maintenance and Troubleshooting

Owner’s Manual for Power Washer 15

Table 4-1. Troubleshooting

Problem Cause Correction

Pump fails to produce

pressure, has erratic pressure,

chattering, loss of pressure,

low water volume.

1. Low pressure nozzle

installed.

2. Water inlet is obstructed.

3. Inadequate water supply.

4. Inlet hose kinked or

leaking.

5. Clogged hose inlet screen.

6. Water supply is over 100ºF

(37.8ºC).

7. High-pressure hose is

obstructed, or leaks.

8. Spray gun leaks.

9. Nozzle is obstructed.

10. Pump is faulty.

1. Replace with high-pressure

nozzle.

2. Clean inlet.

3. Provide adequate water

flow.

4. Straighten inlet hose, patch

leak.

5. Inspect and clean inlet

hose screen.

6. Provide cooler water

supply.

7. Clear obstructions or

replace hose.

8. Replace spray gun.

9. Clean nozzle.

10. Contact Independent

Authorized Service Dealer.

Detergent fails to mix with

spray.

1. Detergent siphoning tube is

not submerged.

2. Detergent siphoning tube/

filter is obstructed or

cracked.

3. High-pressure nozzle

installed.

1. Insert detergent siphoning

tube into detergent.

2. Clean or replace filter/

detergent siphoning tube.

3. Install low-pressure nozzle.

Engine runs well at no-load,

but bogs down when load is

applied.

Engine speed too low. Contact Independent

Authorized Service Dealer.

Engine will not start, or starts

and runs rough.

1. Dirty air filter.

2. Out of fuel

3. Stale fuel.

4. Spark plug wire not

connected to plug.

5. Bad spark plug.

6. Water in fuel.

7. Excessively rich fuel

mixture.

8. Choke in ON position.

1. Clean or replace air filter.

2. Fill fuel tank.

3. Replace with fresh fuel.

4. Connect wire to spark plug.

5. Replace spark plug.

6. Drain fuel tank, replace

with fresh fuel.

7. Contact Independent

Authorized Service Dealer.

8. Set choke to OFF position.

Engine shuts down during

operation.

Out of fuel. Fill fuel tank.

Engine lacks power. Dirty air filter. Replace air filter.

Maintenance and Troubleshooting

Owner’s Manual for Power Washer 16

This page intentionally left blank.

Part No.0L4974 Rev. A 11/24/2015

Specifications are subject to change without notice.

No reproduction allowed in any

form without prior

written consent from Generac Power Systems, Inc.

Generac Power Systems, Inc.

S45 W29290 Hwy. 59

Waukesha, WI 53189

1-888-GENERAC (1-888-436-3722)

generac.com

La page est en cours de chargement...

Generac 7019 Le manuel du propriétaire

Generac 7019 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents