KitchenAid KBRS20ETBL - ARCHITECT II 19.9 Bottom-Fre Manuel utilisateur

KBRS20ETBL - ARCHITECT II 19.9 Bottom-Fre
KitchenAid
Marque
KitchenAid
Modèle
KBRS20ETBL - ARCHITECT II 19.9 Bottom-Fre
Catégorie
Frigos
Taper
Manuel utilisateur
BOTTOM-MOUNT REFRIGERATOR
Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
or visit our website at www.kitchenaid.com
In Canada, call: 1-800-807-6777 or visit our website at www.KitchenAid.ca
RÉFRIGÉRATEUR SUPERPOSÉ
Guide d’utilisation et d’entretien
Au Canada, pour assistance, installation ou service composez le 1-800-807-6777 ou visitez notre site web à www.KitchenAid.ca
Table of Contents/Table des matières.............................................................................2
12828153
2
TABLE OF CONTENTS
REFRIGERATOR SAFETY .............................................................3
INSTALLATION INSTRUCTIONS..................................................4
Unpack the Refrigerator...............................................................4
Location Requirements................................................................4
Electrical Requirements ...............................................................5
Water Supply Requirements........................................................5
Connect the Water Supply...........................................................5
Base Grille ....................................................................................7
Refrigerator Door..........................................................................7
Freezer Drawer.............................................................................9
Adjust the Door ..........................................................................12
Water System Preparation.........................................................12
Factory Trim Kit (on some models)............................................13
Normal Sounds ..........................................................................14
REFRIGERATOR USE..................................................................15
Ensuring Proper Air Circulation..................................................15
Using the Controls .....................................................................15
Electronic Controls.....................................................................15
Digital Controls...........................................................................16
Water Dispenser.........................................................................17
Water Filter Status Light.............................................................17
Water Filtration System..............................................................18
Ice Maker....................................................................................18
REFRIGERATOR FEATURES ......................................................18
Refrigerator Shelves...................................................................19
Crisper and Crisper Cover .........................................................19
Crisper Humidity Control............................................................19
Temperature-Controlled Drawer................................................19
Utility or Egg Bin.........................................................................20
FREEZER FEATURES ..................................................................20
Freezer Baskets..........................................................................20
DOOR FEATURES ........................................................................21
Door Retainer .............................................................................21
Door Bins....................................................................................21
Utility Compartment ...................................................................21
REFRIGERATOR CARE ...............................................................21
Cleaning......................................................................................21
Changing the Light Bulb.............................................................22
Power Interruptions....................................................................22
Vacation and Moving Care.........................................................22
TROUBLESHOOTING ..................................................................23
ASSISTANCE OR SERVICE.........................................................26
In the U.S.A. ...............................................................................26
In Canada ...................................................................................26
Accessories ................................................................................26
WATER FILTER CERTIFICATIONS.............................................26
PRODUCT DATA SHEETS...........................................................27
WARRANTY ..................................................................................28
TABLE DES MATIÈRES
SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................29
INSTRUCTIONS D’INSTALLATION ............................................30
Déballage du réfrigérateur .........................................................30
Exigences d'emplacement.........................................................30
Spécifications électriques..........................................................31
Spécifications de l’alimentation en eau.....................................31
Raccordement de la canalisation d'eau ....................................31
Grille de la base..........................................................................33
Porte du réfrigérateur .................................................................33
Tiroir du congélateur ..................................................................35
Ajustement de la porte...............................................................38
Préparation du système d’eau...................................................38
Ensemble décoratif de l’usine....................................................39
Sons normaux ............................................................................40
UTILISATION DU RÉFRIGÉRATEUR..........................................41
Pour s’assurer d’une circulation d’air appropriée .....................41
Utilisation des commandes........................................................41
Commandes électroniques........................................................41
Commandes numériques...........................................................42
Distributeur d’eau.......................................................................44
Témoin lumineux de l'état du filtre à eau...................................44
Système de filtration d’eau .......................................................44
Machine à glaçons .....................................................................45
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................45
Tablettes du réfrigérateur...........................................................45
Bac à légumes et couvercle.......................................................46
Réglage de l’humidité dans le bac à légumes...........................46
Tiroir à température contrôlée....................................................46
Casier utilitaire ou oeufrier..........................................................47
CARACTÉRISTIQUES DU CONGÉLATEUR...............................47
Paniers de congélateur ..............................................................47
CARACTÉRISTIQUES DE LA PORTE.........................................48
Dispositif de retenue de la porte................................................48
Balconnets dans la porte ...........................................................48
Compartiment utilitaire...............................................................48
ENTRETIEN DU RÉFRIGÉRATEUR ............................................48
Nettoyage ...................................................................................48
Remplacement de l’ampoule d’éclairage ..................................49
Pannes de courant .....................................................................49
Entretien avant les vacances ou lors d’un déménagement.......50
DÉPANNAGE.................................................................................50
ASSISTANCE OU SERVICE.........................................................53
Accessoires ................................................................................53
FEUILLES DE DONNÉES SUR LE PRODUIT.............................54
GARANTIE.....................................................................................55
3
REFRIGERATOR SAFETY
Proper Disposal of Your Old Refrigerator
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
– even if they will sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
■ Take off the doors.
■ Leave the shelves in place so that children may not easily
climb inside.
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
SAVE THESE INSTRUCTIONS
■ Plug into a grounded 3 prong outlet.
■ Do not remove ground prong.
■ Do not use an adapter.
■ Do not use an extension cord.
■ Disconnect power before servicing.
■ Replace all parts and panels before operating.
■ Remove doors from your old refrigerator.
■ Use nonflammable cleaner.
■ Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
■ Use two or more people to move and install refrigerator.
■ Disconnect power before installing ice maker (on ice maker
kit ready models only).
■ Use a sturdy glass when dispensing ice (on some models).
WARNING
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
4
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
Remove the Packaging
■ Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
■ Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see “Refrigerator Safety.”
■ Properly dispose of packaging.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in “Refrigerator Care.”
Location Requirements
■ Your refrigerator is designed for indoor, household use only.
■ To ensure proper ventilation for your refrigerator, allow for a
¹⁄₂" (1.25 cm) space at the top and behind the refrigerator.
■ If your refrigerator has an ice maker, allow extra space at the
back for the water line connections.
■ When installing your refrigerator next to a fixed wall, leave
2¹⁄₈" (5.4 cm) minimum on the hinge side (some models
require more) to allow for the door to swing open.
NOTE: It is recommended that you do not install the refrigerator
near an oven, radiator, or other heat source. Do not install the
refrigerator in a location where the temperature will fall below
55°F (13°C).
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it.
Do not wiggle or “walk” the refrigerator when trying to move
it, as floor damage could occur.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when
removing them to avoid impact from dropping.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
2¹⁄₈" (5.4 cm)
¹⁄₂" (1.25 cm)
5
Electrical Requirements
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control (Thermostat, Refrigerator
or Freezer Control depending on the model) OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.
Water Supply Requirements
Read all directions before you begin.
IMPORTANT:
■ If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
■ All installations must meet local plumbing code requirements.
■ Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
TOOLS NEEDED: Gather the required tools and parts before
starting installation. Read and follow the instructions provided
with any tools listed here. Flat-blade screwdriver, ⁷⁄₁₆" and ¹⁄₂"
open-end wrenches or two adjustable wrenches, ¹⁄₄" nut driver
and drill bit, hand drill or electric drill (properly grounded).
NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
Water Pressure
A cold water supply with water pressure of between 35 and
100 psi (241 and 689 kPa) is required to operate the water
dispenser and ice maker. If you have questions about your water
pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 35 and 100 psi
(241 and 689 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
■ Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
■ Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
■ If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See “Water
Filtration System.”
If you have questions about your water pressure, call a licensed,
qualified plumber.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line
is connected, turn the ice maker OFF.
Connect to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Find a ¹⁄₂" to 1¹⁄₄" (12.7 mm to 3.18 mm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
■ Make sure it is a cold water pipe.
■ Horizontal pipe will work, but the following procedure
must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the lower right rear of refrigerator to
the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄"
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure
both ends of copper tubing are cut square.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
6
5. Using a grounded drill, drill a ¹⁄₄" hole in the cold water pipe
you have selected.
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the ¹⁄₄" drilled hole
in the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws
slowly and evenly so the washer makes a watertight seal. Do
not overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water is
clear. Turn OFF the shutoff valve on the water pipe.
Connect to Refrigerator
Depending on your model, the water line may come down from
the top or up from the bottom. Follow the connection instructions
for your model.
Style 1
1. Remove plastic cap from water valve inlet port. Attach the
copper tube to the valve inlet using a compression nut and
sleeve as shown. Tighten the compression nut. Do not
overtighten. Confirm copper tubing is secure by pulling on
copper tubing.
2. Create a service loop with the copper tubing. Avoid kinks
when coiling the copper tubing. Secure copper tubing to
refrigerator cabinet with a “P” clamp.
3. Turn on water supply to refrigerator and check for leaks.
Correct any leaks.
Style 2
1. Create a service loop (minimum diameter of 2 ft [61 cm]) with
the copper tubing. Avoid kinks when coiling the copper
tubing.
2. Remove the plastic cap from water valve inlet port. Place a
compression nut and sleeve on the copper tubing.
3. Insert the end of the copper tubing into the water valve inlet
port. Shape tubing slightly so that the tubing feeds straight
into the port to avoid kinks.
4. Slide the compression nut over the sleeve and screw into the
water valve inlet port.
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
F
G
A
B
C
D
E
A. Copper tubing
B. “P” clamp
C. Compression nut
D. Compression sleeve
E. Water valve inlet port
A. Plastic water tubing
B. Sleeve
C. Compression nut
D. Copper tubing
A
B
C
D
E
B
A
C
D
7
5. Using an adjustable wrench, hold the nut on the plastic water
line to keep it from moving. Then, with a second wrench turn
the compression nut on the copper tubing counterclockwise
to completely tighten. Do not overtighten.
6. Check connection by pulling on copper tubing. Attach copper
tubing to refrigerator cabinet with a “P” clamp. Turn on water
supply to refrigerator and check for leaks. Correct any leaks.
Complete the Installation
1. Plug into a grounded 3 prong outlet.
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to
completely fill the ice container.
Base Grille
Remove the Base Grille
1. Grasp the grille with both hands.
2. Pull the grille toward you.
Replace the Base Grille
1. See the markings on the inside of the base grille for proper
placement.
2. Align the grille mounting clips with the cabinet slots.
3. Push the grille firmly into the cabinet slots until it snaps into
place.
Refrigerator Door
Graphics are included later in this section.
Remove and Replace Handles (Architect
®
Series)
1. Using a ³⁄₃₂" Allen wrench, loosen the two set screws located
on the side of each handle. See Graphics 2 and 4.
2. Pull the handle straight out from the door. Make sure you
keep the screws for reattaching handles.
3. To replace the handle, reverse the directions.
Remove Handles (Panel Series)
IMPORTANT:
■ Remove the door from refrigerator before removing handles.
■ You must remove the handles to remove the decorator panels
or to reverse the door swing.
1. Using a Phillips screwdriver, remove the top door cap. See
Graphic 3.
2. Tap the bottom edge of the refrigerator door handle upward
with a rubber mallet.
3. Handle will slide up approximately ³⁄₄" (19.05 mm) and release
from the door.
A. Plastic water line
B. Water valve inlet port
C. Compression nut
D. Copper tubing
E. “P” clamp
B
A
C
D
E
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
8
Replace Handles (Panel Series)
1. Make sure the bottom door cap is installed. See Graphic 5.
2. Align handle notches with metal mounting tabs on the side of
the door. Slide the handle down until it locks.
3. Tap the top of the handle with a rubber mallet to ensure a
snug fit.
4. Using a Phillips screwdriver, reinstall the top door cap.
Remove Door and Hinges
IMPORTANT:
■ Remove food and any adjustable door bins or utility bins from
doors.
■ All graphics referenced in the following instructions are
included later in this section after “Final Steps.”
⁵⁄₁₆
" Hex-Head Top Hinge Screw
TOOLS NEEDED: ⁵⁄₁₆", ³⁄₈", ¹⁄₄" hex-head socket wrench, #2
Phillips screwdriver, and a flat-blade screwdriver.
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator door closed until you are ready to lift it
free from the cabinet.
NOTE: Provide additional support for the refrigerator door
while the hinges are being moved. Do not depend on the door
gasket magnets to hold the door in place while you are
working.
3. Remove the parts for the top hinge as shown in Top Hinge
Graphic. Lift the refrigerator door free from the cabinet.
4. Remove the parts for the bottom hinge as shown in the
Bottom Hinge Graphic.
Reverse Door (Architect
®
Series)
IMPORTANT: If you want to reverse your doors so they open
from the opposite side, follow these steps. If you are not
reversing the doors, see “Replace Door and Hinges.”
Cabinet
1. Remove the hinge screws from handle side and move them
to opposite side. See Graphic 1-1.
2. Using a flat-blade screwdriver tip wrapped in masking tape,
remove the cabinet hinge hole plugs from the cabinet top and
move them to the opposite side hinge holes as shown in
Graphic 1-2.
Refrigerator door
1. Remove the refrigerator handle assembly including the
mounting posts and screws. Keep all parts together. See
Graphic 2.
2. Remove the door handle seal screw front. Move to opposite
side of refrigerator door as shown in Graphic 5.
3. Remove the door stop from the bottom edge of the
refrigerator door. Move to opposite side of refrigerator door
as shown in Graphic 3.
4. Attach the door handle mounting posts to the opposite side
of the door.
5. Position refrigerator handle over mounting posts as shown in
Graphic 2. Drive two set screws in the sides of the handle.
6. Tighten all screws. Set aside the door until the hinges and
freezer compartment drawer are in place.
Reverse Door (Panel Series)
IMPORTANT:
■ If you want to reverse your door so it opens from the opposite
side, follow these steps. If you are not reversing the door, see
“Replace Door and Hinges.”
■ You must first remove the handle from the panel series
refrigerator door to reverse the door swing.
1. Using a flat-blade screwdriver tip wrapped in masking tape,
remove the cabinet hinge hole plugs and move them to the
opposite side of the cabinet as shown in Graphic 1.
2. Remove the hinge screws. Move to the opposite side of
cabinet. See Graphic 2.
3. Using a Phillips screwdriver, remove the door stop and door
cap located on the bottom edge of the refrigerator
compartment. See Graphic 5.
4. Using a Phillips screwdriver, remove the top door cap.
5. Remove ¹⁄₄" hex-head screws from top door extension.
Reverse the top door extension so the notched corner turns
in toward the interior of the door. See Graphic 3.
6. Remove the side door trim and handle trim by tapping the
bottom edges upward with a soft rubber mallet. The trim will
slide up and release from the door. See Graphic 4.
7. Replace the bottom door cap and install the door stop on
opposite side of the door. See Graphic 5.
8. Using the alternate side door trim, shipped with the
refrigerator, align notches on trim with metal mounting tabs
on side of door. Slide the trim down until it locks into place.
Tap the top of the trim with a rubber mallet to ensure snug fit.
See Graphic 4.
9. Install handle by aligning handle notches with metal mounting
tabs on side of door. Slide the handle down until it locks. Tap
top of handle with rubber mallet to ensure snug fit. See
Graphic 4.
10. Using a Phillips screwdriver, install the top door cap. See
Graphic 3.
Door Stop Screw
Cabinet Hinge Hole PlugFlat-Head Handle Screw
Door Handle Seal Screw Fron
t
9
Replace Door and Hinges
NOTE: When reversing panel series door, use alternate top hinge
shipped with refrigerator.
1. Replace the parts for the bottom hinge as shown in Bottom
Hinge graphic. Tighten screws. Replace the refrigerator door.
NOTE: Provide additional support for the refrigerator door
while the hinges are being moved. Do not depend on the door
gasket magnets to hold the door in place while you are
working.
2. Assemble the parts for the top hinge as shown in the Top
Hinge Graphic. Do not tighten screws completely.
3. Line up the door so that the bottom of the refrigerator door
aligns evenly with the top of the freezer drawer. Tighten all
screws.
Freezer Drawer
Graphics are included later in this section.
Remove Drawer
IMPORTANT: Two people may be required to complete this
procedure.
1. Open the freezer drawer to full extension.
2. Remove all articles from baskets.
3. Pull the upper wire basket out to full extension and lift out to
remove.
4. Lift lower basket straight up and out to remove.
5. Remove the basket cradles from the drawer rails. Push the
snap attachments inward away from the drawer rails to
unlatch the basket cradles. Lift the basket cradles off of the
drawer rails.
6. Lift the top of the freezer drawer front to disengage drawer
rail hooks from drawer rails. Lift drawer out.
Replace Drawer
IMPORTANT: Two people may be required to complete this
procedure.
1. Pull both drawer rails out to full extension.
2. Locate the notches on the inside of each drawer rail. See
Graphic 6-1.
3. While supporting the drawer front, hook the drawer supports
into the notches on the inside of the drawer rails. Lower the
drawer front into its final position. See Graphic 6-2.
4. Place the basket cradles back on the drawer rails. Align the
snap attachments with the slots on the drawer rails, and
press each snap toward the rail until it clicks.
5. With drawer rails pulled out to full extension, set the lower
basket straight down into the basket cradles.
6. Slide the upper basket into the molded drawer rail. Make sure
the rear of the basket hooks behind the drawer rail stop.
Final Steps
1. Check all holes to make sure that hole plugs and screws are
in place. Reinstall top hinge cover. See Top Hinge Graphic.
2. Plug into a grounded 3 prong outlet.
3. Return all removable door parts to doors and food to
refrigerator.
A. Cradle snap attachment
B. Basket cradle
B
A
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
10
Architect
®
Series
Door Removal &
Replacement
Door Swing Reversal (optional)
A
A. Cabinet Hinge Hole Plugs
1-2
A
A. Door Stop Screws
B. Door Stop
3
Side View
Front View
A
B
A
1-1
A
A. Hinge Screws
5
Door Handle
Seal Screw
Front
2
A.
3
/32" Set Screw
A.
3
/32" Set Screw
4
A
A
Drawer Removal & Replacement
Top Hinge
A. Shim
C. Hinge Screws
B. Center Hinge
A. Hinge Cover Screw
B. Top Hinge Cover
C.
5
/
16
" Hex-Head Hinge Screws
D. Top Hinge
B
A
C
D
Bottom Hinge
A
B
C
6-1 6-2
11
Panel Series
Door Removal &
Replacement
Door Swing Reversal (optional)
Top Hinge
A. Shim
C. Hinge Screws
B. Center Hinge
A.
5
/
16
" Hex-Head Hinge Screws
B. Top Hinge
A
B
Bottom Hinge
A
B
C
6-1 6-2
Drawer Removal & Replacement
A. Cabinet Hinge Hole Plugs
A
2
A
A. Hinge Screws
AB
5
A. Bottom Door Cap
B. Door Stop
4
A.
Handle Trim
B. Side Door Trim
A
B
1
3
B
C
A
B.
1
/
4
" Hex-Head Screws
C. Top Door Extension
A. Top Door Cap
12
Adjust the Door
Depending on your model, your refrigerator may have two
(Style 1) or four (Style 2) adjustable rollers located at the base of
the refrigerator. If your refrigerator seems unsteady or you want
the door to close easier, adjust the refrigerator's tilt using the
instructions below.
1. Remove the base grille. Grasp the grille firmly and pull it
toward you.
2. Using a screwdriver or ³⁄₈" hex driver, turn the roller
adjustment screw(s) on each side to raise or lower that side of
the refrigerator.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the adjustment screws and
rollers. This makes it easier to turn the screws.
■ To raise, turn the roller adjustment screw to the right.
■ To lower, turn the roller adjustment screw to the left.
NOTE: It may take several turns of the roller adjustment
screw to adjust the tilt of the refrigerator.
Style 1 - Front leveling
Style 2 - Front and rear leveling
3. Open the door again to make sure that it closes as easily as
you like. If not, tilt the refrigerator slightly more to the rear by
turning both front adjustment screws to the right. It may take
several more turns, and you should turn both adjustment
screws the same amount.
4. Lower the stabilizing foot by turning it clockwise until it is
firmly against floor.
5. Turn the front adjustment screws counterclockwise to allow
the full weight of the refrigerator to rest on the stabilizing feet.
6. Replace the base grille.
Water System Preparation
Please read before using the water system.
Immediately after installation, follow the steps below to make
sure that the water system is properly flushed.
1. Turn off the ice maker by opening the freezer door and lifting
up the wire shutoff arm as shown.
2. Install the interior water filter. The interior water filter mounting
bracket is located on the left side wall of the refrigerator
compartment.
■ Remove blue bypass cap and retain for later use.
■ Remove the interior water filter from its packaging.
Remove the sealing label from the end of the filter and
insert it into the filter head.
■ Gently rotate the filter clockwise until it stops. Then snap
the filter cover closed.
3. Flush the water system by dispensing and discarding 2 to
3 gal. (8 to 12 L) of water. Flushing the system will take
approximately 6 to 7 minutes and will help clear air from the
line. Additional flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out
of the dispenser.
4. Inspect the filter system for water leaks. If you see water
leaks, see the “Troubleshooting” section.
5. Turn on the ice maker by opening the freezer door and
lowering the wire shutoff arm as shown.
Please refer to the
“Ice Maker” section for further instructions on the operation
of your ice maker.
■ Allow 24 hours to produce the first batch of ice.
■ Discard the first three batches of ice produced.
A. Roller adjustment screw
B. Stabilizing foot
A. Front adjustment screw
B. Rear adjustment screw
C. Stabilizing foot
A
B
A B AB
CC
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
13
Factory Trim Kit (on some models)
There may be an occasion when you will need to remove the
factory-installed trim kit, such as moving the refrigerator to a new
home or installing custom-made decorator panels. Please read
all instructions before removing the trim kit and decorator panels.
Remove the Door Panel
IMPORTANT:
■ Door must be removed from refrigerator before removing
handle.
■ Top trim must be removed from refrigerator before removing
door panel.
1. Remove the refrigerator handle:
■ Using a Phillips screwdriver, remove the top door cap.
■ Tap the bottom edge of refrigerator door handle upward
with a rubber mallet.
■ The handle will slide up approximately ³⁄₄" (19.05 mm) and
release from door.
2. Remove the door panel:
■ Slide out decorator panel and filler board.
■ Store panel and filler board in such a manner as to avoid
scratching.
Replace the Door Panel
1. Replace the refrigerator door panel:
■ Slide the ¹⁄₄" (6.35 mm), maximum thickness, decorator
panel in grooves provided by bottom door cap and side
trim.
■ Slide the filler board into place behind the decorator
panel, if necessary.
2. Attach the handle and trim.
3. Reinstall the refrigerator door.
Remove and Replace Freezer Drawer Panel
NOTE: You do not need to remove the freezer drawer to remove
or replace the decorator panel.
1. Pull the freezer drawer out to access the handle screws.
2. Using a Phillips screwdriver, remove the handle screws and
lift off the handle.
3. Slide the decorator panel and filler board up through handle
opening.
4. Replace the decorator panels by reversing directions.
Care of Decorator Panels
1. Clean panels with stainless steel cleaner and polish or mild
soap and water with a clean, soft, damp cloth.
2. Rinse panels thoroughly and blot dry using a dry, soft cloth or
chamois.
NOTE: Do not use paper towels or cleaners which contain
solvents such as ammonia. They can damage the surface of
the panels.
Install Custom Wood Panels
If you plan to install custom wood decorator panels, you will need
to create the panels yourself or consult your cabinetmaker or
carpenter. See dimensional drawings for wood panel inserts.
Flat Panels:
You can create a custom flat panel a maximum of ¹⁄₄" (6.35 mm)
thick to replace your decorator panels. Flat wood panels less
than ¹⁄₄" (6.35 mm) thick are not recommended.
Raised Panels:
A raised panel design can be created by screwing or gluing wood
panels to ¹⁄₄" (6.35 mm) backing or by using ³⁄₄" (19.05 mm) stock
with routed edges. Allow 2¹⁄₂" (6.35 cm) minimum clearance
between raised edge of panel and handle.
Weight requirements for raised panel inserts:
■ Refrigerator door panel should not exceed 30 lbs (14 kg).
■ Freezer drawer panels should not exceed 15 lbs (7 kg)
combined weight.
A. 2
¹⁄₂
" (6.35 cm) Clearance
B. Raised decorator panel
C. Raised drawer panel
A
B
C
14
Dimensions for Custom Wood Panels
Dimensions for Routing Handle Side of Raised Door
Panels (End View)
Dimensions for Routing Door Panel (Side View)
Normal Sounds
Your new refrigerator may make sounds that your old one didn’t
make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, such as the floor, walls, and cabinets, can make the
sounds seem louder. The following describes the kinds of sounds
and what may be making them.
■ If your refrigerator is equipped with an ice maker, you will hear
a buzzing sound when the water valve opens to fill the ice
maker for each cycle.
■ Your refrigerator is designed to run more efficiently to keep
your food items at the desired temperatures and to minimize
energy usage. The high efficiency compressor and fans may
cause your refrigerator to run longer than your old one. You
may also hear a pulsating or high-pitched sound from the
compressor or fans adjusting to optimize performance.
■ You may hear the evaporator fan motor circulating air through
the refrigerator and freezer compartments. The fan speed
may increase as you open the doors or add warm food.
■ Rattling noises may come from the flow of refrigerant, the
water line, or items stored on top of the refrigerator.
■ Water dripping on the defrost heater during a defrost cycle
may cause a sizzling sound.
■ As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your refrigerator.
■ Contraction and expansion of the inside walls may cause a
popping noise.
■ You may hear air being forced over the condenser by the
condenser fan.
■ You may hear water running into the drain pan during the
defrost cycle.
20 cu. ft. Refrigerator door
A. Handle
B. Door panel
35
5
/
8"
(90.5 cm)
36
1
/
16"
(91.6 cm)
42"
(106.7 cm)
23
1
/
4"
(59.1 cm)
B
A
2¹⁄₂" (6.35 cm)
min.
¹⁄₄" (6 mm) max.
¹⁄₂"
(1.3 cm)
min.
¹⁄₄"
(6.35 mm) max.
Top
Bottom
³⁄₈"
(9.5 mm)
min.
¹⁄₄"
(6.35 mm) max.
Center face
detail between
offsets
15
REFRIGERATOR USE
Ensuring Proper Air Circulation
In order to ensure proper temperatures, you need to permit
airflow between the refrigerator and freezer sections. As shown in
the illustration, cool air enters the freezer section through vents in
the rear and top. The air flows forward through the freezer section
and recirculates under the freezer floor. Cool air enters the
refrigerator section through the top, flows down and across
shelves to the doors and recirculates to return air vents at the
bottom.
Do not block any airflow vents. If the vents are blocked, airflow
will be obstructed and temperature and moisture problems may
occur.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.
Using the Controls
Your model may have Electronic Controls or Digital Controls.
IMPORTANT:
■ The refrigerator control adjusts the refrigerator compartment
temperature. The freezer control adjusts the freezer
compartment temperature.
■ Wait 24 hours for your refrigerator to cool completely before
adding food. If you add food before the refrigerator has
cooled completely, your food may spoil.
NOTE: Adjusting the Refrigerator and Freezer Controls to a
higher (colder) than recommended setting will not cool the
compartments any faster.
■ If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls. See “Ensuring Proper
Air Circulation.”
■ The recommended settings should be correct for normal
household refrigerator use. The controls are set correctly
when milk or juice is as cold as you like and when ice cream
is firm.
Electronic Controls
For your convenience, your refrigerator and freezer controls are
preset at the factory. When you first install your refrigerator, make
sure the controls are still set to the recommended setting as
shown.
Recommended Setting “4”
IMPORTANT:
■ To turn your refrigerator off, press the freezer down arrow
touch pad until a dash (-) appears in both the refrigerator and
freezer displays. Neither compartment will cool.
■ The temperature control range for each compartment is 1
through 7 (coldest).
Adjusting Electronic Controls
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the chart below as
a guide.
Press the up or down arrow touch pads to adjust the
temperature. Except when starting the refrigerator, do not adjust
either control more than one setting at a time. Wait 24 hours for
the temperature to stabilize between adjustments.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm
- Door opened often, large amount
of food added or room
temperature very warm
Adjust REFRIGERATOR
or TEMPERATURE
Control one setting
higher
FREEZER too warm/ice not made
fast enough
- Door opened often, or large
amount of food added or very cold
room temperature (can’t cycle
often enough)
- Heavy ice usage
Adjust FREEZER or
TEMPERATURE Control
one setting higher
REFRIGERATOR too cold
- Controls not set correctly for
your conditions
Adjust REFRIGERATOR
or TEMPERATURE
Control one setting
lower
FREEZER too cold
- Controls not set correctly for
your conditions
Adjust FREEZER or
TEMPERATURE Control
one setting lower
16
Digital Controls
For your convenience, your temperature controls are preset at
the factory. When you first install your refrigerator, make sure the
controls are still set to the recommended set points as shown.
Recommended Settings
IMPORTANT: When the power is on, the temperature display
shows the actual temperature of the compartment.
To Turn Your Refrigerator Off/On:
■ Press the freezer (+) touch pad repeatedly until “OFF”
appears in the freezer display. Allow a few seconds for the
refrigerator to shut off. Neither compartment will cool.
■ Press either the refrigerator or freezer (-) touch pad to turn on
the refrigerator.
Adjusting Digital Controls
The REFRIGERATOR control adjusts the refrigerator
compartment temperature. The FREEZER control adjusts the
freezer compartment temperature.
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the chart as a
guide.
To Adjust Set Point Temperatures:
The first touch of the (+) or (-) touch pad displays the current
temperature set point. The display will show the set point for
approximately 3 seconds, and then return to the actual
temperature.
■ Press the (+) or (-) touch pads until the desired temperature
set point is displayed.
NOTE: Except when first turning on the refrigerator, do not
adjust either temperature control more than one setting at a
time. Wait 24 hours for the temperature to stabilize between
adjustments.
Additional Digital Control Center Features
Max Cool
The max cool feature assists with periods of high refrigerator use,
full grocery loads, or temporarily warm room temperatures.
■ Press the Max Cool touch pad to set the freezer and
refrigerator to the lowest temperature settings. Press the Max
Cool touch pad again to return to the normal refrigerator set
point.
NOTE: The Max Cool feature will automatically shut off in
approximately 12 hours.
OptimIce
®
Feature
The OptimIce
®
feature assists with temporary periods of heavy
ice use by increasing ice production.
■ Press the OptimIce
®
feature touch pad to set the freezer to
the lowest temperature setting. Press the OptimIce
®
feature
touch pad again to return to the normal freezer set point.
NOTE: The OptimIce
®
feature will automatically shut off in
approximately 24 hours.
Holiday Mode
In Holiday Mode, the freezer will not automatically defrost as
often to conserve energy.
■ Press the Holiday Mode touch pad until the indicator light is
lit to turn on this feature. Press the Holiday Mode touch pad
again or open the refrigerator door to turn off this feature.
NOTE: The refrigerator door may be opened within 1 hour of
setting Holiday Mode without turning off the feature.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm
- Door opened often, large amount
of food added or room
temperature very warm
Adjust REFRIGERATOR
TEMPERATURE Control
1° lower
FREEZER too warm/ice not made
fast enough
- Door opened often, or large
amount of food added or very cold
room temperature (can’t cycle
often enough)
- Heavy ice usage
Adjust FREEZER
TEMPERATURE Control
1° lower
REFRIGERATOR too cold
- Controls not set correctly for
your conditions
Adjust REFRIGERATOR
TEMPERATURE Control
1° higher
FREEZER too cold
- Controls not set correctly for
your conditions
Adjust FREEZER
TEMPERATURE Control
1° higher
CONDITION/REASON: ADJUSTMENT:
17
Temp Alarm
The Temp Alarm feature provides temperature information in the
event of a power outage.
Power Outage: During a power outage, if the temperatures in the
refrigerator and freezer compartments exceed normal operating
temperatures, the highest temperature reached will be displayed.
■ Press the Temp Alarm touch pad until the indicator light is lit,
to turn on this feature. Press and hold Temp Alarm for
3 seconds until the indicator light goes off to turn off this
feature.
Temperature Alarm: An alarm will sound repeatedly if the freezer
or refrigerator compartment temperatures exceed normal
operating temperatures for an hour or more.
The temperature displays will alternately show the current
temperatures and the highest temperatures the compartments
reached.
■ Press the Temp Alarm touch pad once to stop the audible
alarm and alternating temperature displays. The Temp Alarm
light will continue to flash until the refrigerator returns to the
set temperature.
Door Alarm
The Door Alarm feature sounds a chime every few seconds when
the refrigerator door has been left open for 5 continuous minutes.
The chime will sound until the door is closed or Door Alarm is
turned off.
■ Press the Door Alarm touch pad to turn this feature on or off.
The indicator light will be lit when the Door Alarm feature is
on.
Water Filter Status Light and Filter Reset
(on some models)
See “Water Filter Status Light.”
Digital Control User Preferences
The control center allows you to set user preferences, if desired.
Temperature Display (F_C)
This preference allows you to change the temperature display.
F - Temperature in degrees Fahrenheit
C - Temperature in degrees Celsius
Alarm (AL)
This preference allows you to turn off the sound of all alarms.
ON - You will hear the alarm sound.
OFF - You will not hear the alarm sound.
Sabbath Mode (SAB)
IMPORTANT: This preference does not disable interior lights.
ON - All control panel lights will be disabled.
OFF - All control panel lights will be enabled.
NOTE: Press any touch pad on the control panel to restore the
control panel lights.
To Access the User Preferences Menu:
1. Press and hold the Door Alarm touch pad for 3 seconds. The
preference name will appear in the Freezer display and the
preference status (F or C) or (ON or OFF) will appear in the
Refrigerator display.
2. Use the Freezer (+) or (-) touch pads to scroll through the
preference names. When the desired preference name is
displayed, press the Refrigerator (+) or (-) touch pads to
change the preference status.
3. Set your preferences by pressing and holding the Door Alarm
touch pad for 3 seconds, or by shutting the refrigerator
compartment door.
Water Dispenser
(on some models)
If you did not flush the water system when the refrigerator was
first installed, dispense water into a container until you draw and
discard 2 to 3 gal. (8 to 12 L) or for approximately 6 to 7 minutes
after the water begins dispensing. The water you draw and
discard rinses the pipes. Allow several hours for the refrigerator
to cool down and chill water.
Dispensing Water
1. Hold a container under the dispenser while pressing the
button.
2. Release the button to stop dispensing.
NOTE: Dispense enough water every week to maintain a fresh
supply.
Water Filter Status Light
(on some models)
The water filter status light will help you know when to change
the water filter. When the yellow (Order) light is on, it is almost
time to change the water filter. When the red (Replace) light is on,
a new water filter should be installed. See “Water Filtration
System.”
After replacing the water filter, press and hold FILTER RESET for
3 seconds until the Order or Replace light turns off.
18
Water Filtration System
IMPORTANT:
■ The water filter should be replaced when the status light is
red (Replace) or earlier if the flow of water to your water
dispenser or ice maker decreases noticeably.
■ Air trapped in the system may cause water and the water
filter to eject. Dispense water for 2 minutes before removing
the used water filter.
Replacing the Water Filter
The water filter mounting bracket is located on the right side of
the refrigerator compartment.
1. Turn the used water filter counterclockwise until it releases
from the filter mounting bracket.
2. Drain water from the water filter into the sink, and discard the
used water filter. Wipe up the excess water in the filter cover.
3. Remove the sealing label from the end of the new water filter
and insert the water filter into the filter mounting bracket.
Gently rotate the water filter clockwise until it stops, and snap
the filter cover closed.
4. Flush the water system by dispensing and discarding 2 to
3 gal. (8 to 12 L) of water. Cleaning the system will take
approximately 6 to 7 minutes and will help clear air from the
line. Additional flushing may be required in some households.
5. Inspect the water filter system for leaks. If you see water
leaks, see “Troubleshooting.”
Using the Dispenser Without a Water Filter
You can use the water dispenser without a water filter, but your
water will not be filtered. If you choose this option, replace the
water filter with the blue bypass cap.15
Ice Maker
Turning the Ice Maker On/Off
NOTE: Do not force the wire shutoff arm up or down.
■ To turn the ice maker on, simply lower the wire shutoff arm.
NOTE: Your ice maker has an automatic shutoff. As ice is
made, the ice cubes will fill the ice storage bin and the ice
cubes will raise the wire shutoff arm to the OFF (arm up)
position.
■ To manually turn the ice maker off, lift the wire shutoff arm to
the OFF (arm up) position and listen for the click to make sure
the ice maker will not continue to operate.
Ice Production Rate
■ Normal Ice Production: The ice maker should produce a
complete batch of ice every 3 hours. If ice is not being made
fast enough, adjust the Freezer Control to a lower (colder)
number in steps. Wait 24 hours. If necessary, gradually adjust
the Freezer Control to the lowest setting, waiting 24 hours
between each adjustment.
■ OptimIce Production (on some models): The ice maker
should produce approximately 16 to 20 batches of ice in a
24-hour period. If your refrigerator has the OptimIce
production feature, press the OptimIce touchpad.
Remember
■ Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
■ The quality of your ice will be only as good as the quality of
the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker
and lead to poor quality ice. If a softened water supply cannot
be avoided, make sure the water softener is operating
properly and is well maintained.
■ Do not store anything on top of the ice maker or in the ice
storage bin.
REFRIGERATOR FEATURES
Your model may have some or all of these features.
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when
removing them to avoid impact from dropping.
19
Refrigerator Shelves
The shelves in your refrigerator are adjustable to meet your
individual storage needs.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will make
finding the exact item you want easier. It will also reduce the
amount of time the refrigerator door is open, and save energy.
Slide-out Shelves
■ To slide out shelf, gently pull front of shelf toward you.
■ To slide in shelf, push shelf in until it stops.
Shelves and Shelf Frames
To Remove and Replace a Shelf/Shelf Frame:
1. Remove the shelf/frame by tilting it up at the front and lifting it
out of the shelf supports.
2. Replace the shelf/frame by guiding the rear shelf hooks into
the shelf supports. Tilt the front of the shelf up until rear shelf
hooks drop into the shelf supports.
3. Lower the front of the shelf and check to make sure that the
shelf is securely in position.
Crisper and Crisper Cover
To Remove and Replace the Crisper(s):
1. Slide crisper(s) straight out to the stop. Lift the front of the
crisper(s) and slide out the rest of the way.
2. Replace the crisper(s) by sliding back in fully past the drawer
stop.
To Remove the Crisper(s) Cover:
1. Remove crisper(s).
2. Holding the glass insert firmly with one hand, press up in
center of glass insert until it rises above the plastic frame.
Gently, slide the glass insert forward to remove.
3. Lift the cover frame up and remove it.
To Replace Crisper(s) Cover:
NOTE: Before reinstalling the cover, make sure the
U-shaped reinforcement bar is reinstalled in the front edge of the
crisper cover.
1. Fit back of cover frame into supports on side walls of the
refrigerator and lower the front of the cover frame into place.
2. Slide rear of glass insert into cover frame and lower front into
place.
Crisper Humidity Control
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and
HIGH.
LOW (open) lets moist air out of the crisper for best storage of
fruits and vegetables with skins.
■ Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store
in a loosely closed paper bag on a refrigerator shelf.
■ Vegetables with skins: Place in plastic bags or plastic
container and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of
fresh, leafy vegetables.
■ Leafy vegetables: Wash in cold water, drain and trim or tear
off bruised and discolored areas. Place in plastic bag or
plastic container and store in crisper.
Temperature-Controlled Drawer
The full-width, temperature-controlled drawer can be used to
store large party trays, deli items, or beverages. For storage
flexibility the drawer features a divider and an adjustable
temperature control.
NOTE: Do not place leafy vegetables in the temperature-
controlled drawer. Colder temperatures could damage leafy
produce.
Drawer Removal and Replacement
Depending on your model, your refrigerator may have one of two
drawer styles. Follow the instructions for the appropriate drawer
style.
Style 1 - Flat-lid Drawer
To remove the drawer:
1. Pull the drawer out to its full extension.
2. Tilt up the front of the drawer and pull it straight out.
To replace the drawer:
1. Push the metal glide rails to the rear of the refrigerator.
2. Place the drawer onto the glide rails and slide the drawer
toward the rear of the refrigerator.
LOW
LOW
HIGH
HIGH
20
Style 2 - Lift-up-lid Drawer
To remove the drawer:
1. Lift the lid. Pull the drawer out to its full extension.
2. Tilt up the front of the drawer and pull it straight out.
To replace the drawer:
1. Push the metal glide rails to the rear of the refrigerator.
2. Place the drawer onto the glide rails and slide the drawer
toward the rear of the refrigerator.
Drawer Divider
To Remove the Divider:
1. Pull the drawer out to its full extension.
2. Lift the front of the divider to unhook it from the rear wall of
the drawer and lift the divider out.
To Replace the Divider:
1. Hook the back of the divider over the rear wall of the drawer.
2. Lower the divider into place.
Drawer Temperature Control
The temperature control, located under the lid on the right-hand
side of the drawer, regulates the amount of cold air coming into
the drawer.
NOTE: Cold air directed into the drawer can decrease the
refrigerator temperature. The refrigerator temperature may need
to be adjusted.
■ Slide the temperature control to the least cold setting if you
want the drawer to be the same temperature as the
refrigerator compartment.
■ Slide the temperature control to a colder setting when you
want the drawer to be colder than the refrigerator
compartment.
NOTE: Use the coldest setting when storing meats.
Meat Storage Guide
Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish ................. use same day as purchased
Chicken, ground beef, variety meats (liver)............... 1-2 days
Cold cuts, steaks/roasts ........................................... 3-5 days
Cured meats ........................................................... 7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.
Utility or Egg Bin
Depending on your model, you may have a one, two or three
piece bin. Eggs may be stored in the egg tray or loose in the bin.
NOTE: Store eggs in a covered container for long-term storage. If
your model does not have an egg storage bin, store eggs in their
original carton on an interior shelf.
FREEZER FEATURES
Your model may have some or all of these features.
Freezer Baskets
To Remove and Replace Wire Baskets:
Upper basket
1. Remove all items from basket. Remove basket by pulling
basket out to its full extension and lift out.
2. Replace basket by sliding into upper molded railing. Make
sure that rear of basket hooks behind rail catch.
Upper basket divider
■ The upper basket divider separates ice making from frozen
food storage and it helps keep ice from falling behind the
basket assemblies.
■ The upper basket divider is designed to be non-removable
and should remain in the basket.
Lower basket
1. Remove all items from basket. Remove the basket by lifting it
from the rail guides.
2. Replace the basket by placing into rail guides.
Lower basket divider
The lower basket divider is designed to be non-removable and it
should remain in the basket.
A. Divider
A
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

KitchenAid KBRS20ETBL - ARCHITECT II 19.9 Bottom-Fre Manuel utilisateur

KBRS20ETBL - ARCHITECT II 19.9 Bottom-Fre
KitchenAid
Marque
KitchenAid
Modèle
KBRS20ETBL - ARCHITECT II 19.9 Bottom-Fre
Catégorie
Frigos
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents