ZENOAH KOMATSU TR2000 Manuel utilisateur

Marque: ZENOAH KOMATSU

Modèle: TR2000

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

BC2001

TR2000

T3338-93110 (209)

OPERATOR’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE D’ISTRUZIONI

MANUAL DE INSTRUCCIONES

BRUSHCUTTERS

DEBROUSSAILLEUSE

FREISCHNEIDER

DECESPUGLIATORE

DESBROZADOR

English

Français Deutsch

Italiano

Español

ATENCION!!!

RIESGO DE DAÑO AUDITIVO

EN NORMALES CONDICIONES DE UTILIZACIÓN, ESTA MAQUINA PUEDE

TOLERAR, PARA EL OPERADOR ENCARGADO, UN NIVEL DE EXPOSICÍON

DIARIO A RUIDO EQUIVALENTE O SUPERIOR A

85 dB(A)

WARNING!!!

RISK OF DAMAGING HEARING

IN NORMAL CONDITIONS OF USE, THIS MACHINE

MAY INVOLVE A DAILY LEVEL OF PERSONAL EXPOSURE TO NOISE

FOR THE OPERATOR EQUAL TO OR GREATER THAN

85 dB(A)

ATTENTION!!!

DANGER D'ATTEINTE A L'OUIE

L'OPERATEUR UTILISANT NORMALEMENT CETTE MACHINE

PEUTS S'EXPOSER QUOTIDIENNEMENT

A UN BRUIT EGAL OU DEPASSANT

85 dB(A)

ACHTUNG!!!

HÖRSCHADEN - RISIKO

UNTER NORMALEN ANWENDUNGSBEDIGUNGEN

KANN DIESES GERÄT DIE BEDIENUNGSPERSON

EINEM TÄGLICHEN GERÄUSCHPEGEL VON

85 dB(A)

ODER MEHR AUSSETZEN

ATTENZIONE!!!

RISCHIO DI DANNO UDITIVO

NELLE NORMALI CONDIZIONI DI UTILIZZO, QUESTA MACCHINA PUÒ

COMPORTARE PER L'OPERATORE ADDETTO, UN LIVELLO DI ESPOSIZIONE

PERSONALE E GIORNALIERO A RUMORE PARI O SUPERIORE A

85 dB(A)

MODEL SOUND LEVEL VIBRATION LEVEL

MODELE NIVEAU SONORE NIVEAU DE VIBRATION

MODELLE KLANGPEGEL VIBRATIONSPEGEL

MODELLO LIVELLO DEL SUONO LIVELLO DI VIBRAZIONE

MODELO NIVEL DE SONIDO NIVEL DE VIBRACION

EN27917 ISO 10884 ISO 7916

LwA

guaranteed

22.5 cm

96.6dB(A) 108dB(A) 2.7m/s

3.9m/s

LpA idling racing

English Français

SAFETY FIRST

Instructions contained in warnings

within this manual marked with a

symbol concern critical points which

must be taken into consideration to

prevent possible serious bodily injury,

and for this reason you are requested

to read all such instructions carefully

and follow them without fail.

■ WARNINGS IN THE MANUAL

This mark indicates instructions which

must be followed in order to prevent

accidents which could lead to serious

bodily injury or death.

This mark indicates instructions which

must be followed, or it leads to mechanical

failure, breakdown, or damage.

This mark indicates hints or directions

useful in the use of the product.

NOTE

IMPORTANT

WARNING

SECURITE

Les instructions contenues dans les

mises en garde de ce mode d’emploi

portant le symbole concernent les

points critiques qui doivent être pris en

considération pour éviter les blessures

corporelles graves, c’est pourquoi ces

précautions doivent être

rigoureusement suivies.

■ DIFFERENTS TYPES

D’AVERTISSEMENT DE CE MODE

D’EMPLOI

Les instructions repérées par ce symbole

doivent être rigoureusement suivies afin

d’éviter tout accident pouvant entraîner

des blessures corporelles graves ou la

mort.

Les instructions repérées par ce symbole

doivent être suivies afin d’éviter tout

incident mécanique, panne ou

endommagement de la débroussailleuse.

Remarques utilisées dans des instructions

ou conseils supplémentaires pour

l’utilisation de cette débroussailleuse.

REMARQUE

IMPORTANT

AVERTISSEMENT

Contents Tables des matieres

1. Parts location...............................................8

2. Specifications ............................................10

3. Warning labels on the machine................12

4. Symbols on the machine ..........................12

5. For safe operation .....................................14

6. Set up..........................................................26

7. Fuel .............................................................28

8. Operation....................................................32

9. Maintenance...............................................38

10. Storage .......................................................46

11. Troubleshooting guide..............................48

1. Emplacement des pieces............................8

2. Fiche technique ........................................10

Etiquettes d’avertissement sur la machine

.......12

4. Symboles utilises sur la machine............12

5. Consignes de securite ..............................14

6. Assemblage ...............................................26

7. Carburant ...................................................28

8. Fonctionnement.........................................32

9. Entretien.....................................................38

10. Rangement.................................................46

11.

Guide de localisation des pannes

.................48

EspañolDeutsch Italiano

SICHERHEIT HAT VORRANG

Die Hinweise in den Warnungen dieser

Anleitung bzw. auf den mit einem -

Symbol gekennzeichneten

Warnplaketten sind von größter

Bedeutung für die Betriebssicherheit.

Deshalb sollten Sie diese Warnungen

sorgfältig durchlesen und strikt

beachten, um das Risiko von schweren

Verletzungen zu vermeiden.

■ WARNHINWEISE IN DER

ANLEITUNG

Dieses Symbol bedeutet, daß diese

Instruktionen befolgt werden müssen,

damit Unfälle mit folgenschweren

Verletzungen, die u.a. zum Tode führen

können, vermieden werden.

Dieses Symbol bedeutet, daß diese

Instruktionen befolgt werden müssen oder

es kommt zu mechanischen Defekten,

Versagen des Gerätes oder Schäden.

Dieses Symbol zeigt Tips oder Ratschläge

für den Gerätebetrieb an.

HINWEIS

WICHTIG

WARNUNG

LA SICUREZZA INNANZI TUTTO

Le istruzioni contenute nelle sezioni di

avvertimento precedute dal simbolo

riguardano dei punti critici che

devono essere osservate per prevenire

potenziali lesioni personali gravi. Per

questo motivo, dovete leggere tutte

queste istruzioni attentamente ed

osservarne il contenuto in ogni

momento.

■ SEGNALAZIONI USATE NEL

MANUALE

Questo marchio rappresenta delle

istruzioni che devono essere osservate

per prevenire eventuali incidenti che

possono causare lesioni gravi o addirittura

mortali.

Questo marchio indica delle istruzioni che

devono essere seguite per evitare

malfunzionamenti meccanici, guasti o

danni.

Questo marchio indica dei suggerimenti o

indicazioni utili per l’utilizzo del prodotto.

NOTA

IMPORTANTE

AVVERTIMENTO

LA SEGURIDAD PRIMERO

Las instrucciones que aparecen en

este manual bajo las advertencias

marcadas con el símbolo hacen

referencia a puntos críticos que deben

tomarse en consideración para evitar

posibles lesiones físicas; por esta

razón, le solicitamos que lea

detenidamente todas estas

instrucciones y que las siga

estrictamente.

■ ADVERTENCIAS CONTENIDAS EN

EL MANUAL

Bajo este símbolo aparecen instrucciones

que se deben seguir a fin de evitar

accidentes que pueden causar serias

lesiones físicas o la muerte.

Bajo este símbolo aparecen instrucciones

importantes que se deben seguir; ignorar

estas instrucciones puede ocasionar fallos

mecánicos, desperfectos o daños.

Este símbolo hace referencia a consejos o

indicaciones que son de utilidad para el

uso del producto.

NOTA

IMPORTANTE

ADVERTENCIA

Inhalt ContenidoIndice

1. Ubicazione dei componenti........................9

2. Dati tecnici .................................................11

Etichetta di avvertimento sull’apparecchio

.......13

4. Simboli sulla macchina.............................13

5. Per un funzionamento sicuro...................15

6. Impostazione..............................................27

7. Carburante .................................................29

8. Funzionamento..........................................33

9. Manutenzione.............................................39

10. Immagazzinaggio.......................................47

11. Localizzazione dei guasti..........................49

1. Situación de las piezas ...............................9

2. Especificaciohes .......................................11

Etiqueta de advertencia en la máquina

..........13

Símbolos presentes en la máquina

...............13

5. Instrucciones de seguridad......................15

6. Montaje.......................................................27

7. Combustible...............................................29

8. Uso..............................................................33

9. Mantenimiento ...........................................39

10. Almacenamiento........................................47

11. Guía de localización y solución de

problemas ..................................................49

1. Anordnung der bauteile..............................9

2. Technische daten ......................................11

3. Warnaufkleber auf der Maschine .............13

4. Symbole auf der maschine.......................13

5. Sicherer betrieb .........................................15

6. Zusammenbau ...........................................27

7. Kraftstoff ....................................................29

8. Betrieb ........................................................33

9. Wartung......................................................39

10. Lagerung ....................................................47

11. Fehlersuche ...............................................49

English Français

1. Parts location 1. Emplacement des pieces

[BC2001]

[TR2000]

(1) Primer pump

(2) Air cleaner cover

(3) Choke lever

(4) Fuel tank

(5) Starter knob

(6) Line head

(7) Gear case

(8) Debris guard

(9) Loop handle

(10) Drive shaft housing

(11) Sholder strap hanger

(12) Throttle lever

(13) Ignition switch

(14) Throttle cable

(1) Pompe d’amorçage

(2) Capot du filtre à air

(3) Levier de starter

(4) Réservoir de carburant

(5) Poignée de démarrage

(6) Tete de coupe a fil

(7) Boîtier du renvoi d’angle

(8) Cache de protection

(9) Poignée

(10) Tube de l’arbre d’entraînement

(11) Fixation du harnais

(12) Levier d’accélération

(13) Bouton d’allumage

(14) Câble d’accélérateur

EspañolDeutsch Italiano

1. Anordnung der bauteile 1. Ubicazione dei componenti 1. Situación de las piezas

(1) Anlaßeinspritzpumpe

(2) Luftfilterabdeckung

(3) Chokehebel

(4) Kraftstofftank

(5) Startknopf

(6) Schnurkopfes

(7) Winkelgetriebe

(8) Abfallschutz

(9) Schleifengriff

(10) Antriebswelle

(11) Schultergurtklammer

(12) Drosselklappenhebel

(13) Zündschalter

(14) Drosselklappenkabel

(1) Pompa del cicchetto

(2) Coperchio del filtro dell’aria

(3) Leva del dispositivo di

avviamento a freddo

(4) Serbatoio del carburante

(5)

Manopola del motorino di avviamento

(6) Strumento da taglio a corda

(7) Scatola degli ingranaggi

(8) Protezione contro i detriti

(9) Maniglia ergonomica

(10) Albero motore

(11) Occhiello per tracolla

(12) Leva del gas

(13) Interruttore di accensione

(14) Cavo del gas

(1) Cebador

(2) Cubierta del filtro de aire

(3) Palanca del estrangulador

(4) Tanque de combustible

(5) Arrancador

(6) Cabezal de línea

(7) Caja de engranajes

(8) Protector contra desechos

(9) Mango

(10) Eje de accionamiento

(11) Colgador de correa para hombro

(12) Palanca del acelerador

(13) Interruptor de encendido

(14) Cable del acelerador

English

2. Specifications

Français

2. Fiche technique

■ BC2001/TR2000

Overall size (L x W x H) ················································································································· 1795 x 230 x 303 / 1795 x 340 x 303 mm

Dry weight ····················································································································································································· 4.1 / 4.7 kg

Engine Type ··················································································································································· Air-cooled 2-stroke gasoline

Model······································································································································································ Zenoah G20LS

Displacement ····································································································································································· 21.7cm

Fuel ···················································································································································· Mixture (Gasoline 25 : Oil 1)

Carburetor ····························································································································································· Diaphragm type

Ignition system········································································································································································ C.D.I

Spark plug ································································································································································NGK BPMR7A

Fuel tank capacity ···················································································································································································0.5

Starter ························································································································································································ Recoil starter

Clutch····················································································································································································· Centrifugal type

Reduction ratio······················································································································································································· 1.462

Cutting head rotating direction·················································································································· Counter-clockwise(Operator view)

Specifications are subject to change without notice.

■ BC2001/TR2000

Dimensions totales (L x L x H)······································································································· 1795 x 230 x 303 / 1795 x 340 x 303 mm

Poids à vide····················································································································································································4,1 / 4,7 kg

Moteur Type ·········································································································································· 2 temps à essence refroidi par air

Modèle···································································································································································· Zenoah G20LS

Cylindrée············································································································································································21,7 cm

Carburant······································································································································· Mélange (essence 25 : huile 1)

Carburateur ····················································································································································· Typa à Diaphragme

Système d’allumage ······························································································································································· C.D.I

Bougie d’allumage··················································································································································· NGK BPMR7A

Contenance du réservoir de carburant··················································································································································· 0,5

Starter··················································································································································································· Starter à détente

Embrayage············································································································································································· Type centrifuge

Rapport de réduction·············································································································································································· 1,462

Sens de rotation de la tête de coupe············································································································ Anti-horaire (vue de l’opérateur)

Ces spécifications peuvent être modifiées sans préavis.

Deutsch

2. Technische Daten

Italiano

2. Dati tecnici

Español

2. Especificaciohes

■ BC2001/TR2000

Tamaño global (Long x Anch x Alt)································································································ 1795 x 230 x 303 / 1795 x 340 x 303 mm

Peso en seco················································································································································································ 4,1 / 4,7 kg.

Motor Tipo··························································································································· Refrigerado por aire / gasolina de 2 tiempos

Modelo ··································································································································································· Zenoah G20LS

Desplazamiento ································································································································································ 21,7 cm

Combustible ································································································································· Mezcla (Gasolina 25: Aceite 1)

Carburador ····························································································································································· Tipo diafragma

Sistema de encendido ···························································································································································· C.D.I

Bujía ······································································································································································· NGK BPMR7A

Capacidad del depósito de combustible ················································································································································ 0,5

Arrancador······························································································································································· De cuerda con retroceso

Embrague················································································································································································ Tipo centrífugo

Relación de reducción·············································································································································································1,462

Dirección de rotación de cabeza cortador················································· Sentido contrario a las agujas del reloj (vista desde el operador)

Especificaciones sujetas a cambios sin previo aviso.

■ BC2001/TR2000

Abmessungen (L x B x H)·············································································································· 1795 x 230 x 303 / 1795 x 340 x 303 mm

Trockengewicht ············································································································································································· 4,1 / 4,7 kg

MotorTyp ···································································································································· luftgekühlter 2-Takt-Benzinmotor

Modell····································································································································································· Zenoah G20LS

Hubraum ··········································································································································································· 21,7 cm

Kraftstoff ······································································································································ Gemisch(Benzin 25, Öl 1 Anteil)

Vergaser ····································································································································································· Membrantyp

Zündsystem ············································································································································································ C.D.I

Zündkerze ······························································································································································· NGK BPMR7A

Tankkapazität························································································································································································· 0,5

Kupplung············································································································································································ Fliehkraftkupplung

Untersetzungsverhältnis········································································································································································· 1,462

Schneidekopf-Drehrichtung·················································································································· gegen Uhrzeigersinn (vom Bediener)

Technischen Daten können ohne Vorankündigung geändert werden.

■ BC2001/TR2000

Dimensioni (L x P x H) ··················································································································· 1795 x 230 x 303 / 1795 x 340 x 303 mm

Peso a vuoto ················································································································································································· 4,1 / 4,7 kg

Motore Tipo ········································································································· Motore a benzina a 2 tempi con raffreddamento ad aria

Modello··································································································································································· Zenoah G20LS

Cilindrata··········································································································································································· 21,7 cm

Carburante ·········································································································································· Miscela (benzina 25/ olio 1)

Carburatore···························································································································································· Tipo diaframma

Sistema di accensione···························································································································································· C.D.I

Candela··································································································································································· NGK BPMR7A

Capacità del serbatoio del carburante·················································································································································· 0,5 litri

Avviamento············································································································································································ Starter a rinculo

Frizione················································································································································································· Tipo centrifugale

Rapporto di riduzione············································································································································································· 1,462

Direzione di rotazione della testa di taglio····················································································· Nel senso antiorario (visto dall’operatore)

Le specifiche sono soggette a modifiche senza preavviso.

English Français

3. Warning labels on the

machine

3. Etiquettes d’avertissement

sur la machine

(1) Read owner's manual before

operating this machine.

(2) Wear head, eye and ear protection.

(3) Warning/Attention

(4) Keep all children, bystanders and

helpers 15 meters away from the

brushcutter

If warning labels peel off or become soiled

and impossible to read, you should

contact the dealer from which you

purchased the product to order new labels

and affix them in the required location(s).

Never remodel your brushcutter.

We won't warrant the machine, if you use

the remodeled brushcutter or you don't

observe the proper usage written in the

manual.

WARNING

IMPORTANT

(1) Lire le mode d’emploi avant

d’utiliser cette machine.

(2) Porter un casque de sécurité, des

lunettes de sécurité et un casque

antibruit.

(3) Avertissement/Attention

(4) Interdire aux enfants ou à toute

personne de s’approcher dans un

rayon de 15 mètres de la

débroussailleuse.

Si les étiquettes d’avertissement se

décollent, deviennent sales ou impossible

à lire, commander de nouvelles étiquettes

auprès du revendeur pour les remplacer.

Ne pas modifier la débroussailleuse.

La garantie sera annulée si la

débroussailleuse a été modifiée ou

utilisée de manière non conforme aux

instructions de ce mode d’emploi.

AVERTISSEMENT

IMPORTANT

4. Symbols on the machine

4. Symboles utilises sur la

machine

For safe operation and maintenance,

symbols are carved in relief on the

machine. According to these indications,

please be careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE"

Position:

FUEL TANK CAP

(b) The direction to close the choke

Position:

AIR CLEANER COVER

Position:

AIR CLEANER COVER

Des symboles en relief ont été placés sur

la machine pour assurer la sécurité à

l’usage et faciliter l’entretien. Prendre soin

d’observer les indications suivantes afin

d’éviter les erreurs.

(a) Emplacement de remplissage du

“MELANGE”

Emplacement:

BOUCHON DU RESERVOIR DE

CARBURANT

(b) Position fermée du starter

Emplacement:

CAPOT DU FILTRE A AIR

Emplacement:

CAPOT DU FILTRE A AIR

EspañolDeutsch Italiano

3. Warnaufkleber auf der

Maschine

3. Etichetta di avvertimento

sull’apparecchio

3. Etiqueta de advertencia en

la máquina

(1) Vor dem Betrieb dieser Maschine,

die Bedienungsanleitung lesen.

(2) Kopf-, Augen und Ohrenschutz

tragen.

(3) Warnung/Achtung

(4) Kinder, Zuschauer und Helfer 15

Meter vom Freischneider entfernt

halten.

Wenn Warnplaketten sich lösen oder

schmutzig und nicht mehr lesbar sind,

verständigen Sie Ihren Händler bei dem

Sie das Produkt gekauft haben, um neue

Plaketten zu bestellen und diese an den

erforderlichen Positionen zu befestigen.

Ihren Freischneider niemals

modifizieren.

Die Garantie erlischt, wenn Sie einen

modifizierten Freischneider verwenden

oder Sie nicht den in der

Bedienungsanleitung beschriebenen

Betrieb beachten.

WARNUNG

WICHTIG

(1) Leggete il manuale d’istruzioni

prima di usare questa macchina.

(2) Indossate il casco, gli occhiali di

protezione e le cuffie.

(3) Avvertimento/Attenzione

(4) Tenete i bambini, eventuali

spettatori ed aiutanti ad una

distanza di 15 metri dal

decespugliatore.

Se un’etichetta di avvertimento si stacca o

si sporca e diventa così illeggibile,

contattate il rivenditore presso il quale

avete acquistato il prodotto per ordinare

delle nuove etichette. Poi fissate le nuove

etichette negli appositi luoghi.

Non modificate mai il decespugliatore.

Se modificate il decespugliatore

oppure non seguite le istruzioni fornite

in questo manuale, la garanzia sarà

nulla.

AVVERTIMENTO

IMPORTANTE

(1) Lea el manual de instrucciones

antes de usar esta máquina.

(2) Use protección para la cabeza, ojos

y oídos.

(3) Advertencia/Atención

(4) Mantenga a niños, espectadores y

ayudantes a una distancia de 15

metros del desbrozador.

Si las etiquetas de advertencia se

desprenden o se manchan y se vuelven

ilegibles, contacte al distribuidor donde

adquirió el producto y solicite nuevas

etiquetas. Fije las nuevas etiquetas en las

posiciones correspondientes.

Nunca haga ningún tipo de

modificación al desbrozador.

No podemos garantizar la máquina si

usted utiliza el desbrozador

remodelado o si no sigue las

instrucciones de uso contenidas en

este manual.

ADVERTENCIA

IMPORTANTE

4. Symbole auf der Maschine 4. Simboli sulla macchina

4. Símbolos presentes en la

máquina

Für einen sicheren Betrieb und eine

sichere Wartung sind Symbole als

Hilfestellung auf die Maschine eingeprägt.

Gehen Sie gemäß diesen Anzeigen

vorsichtig vor und machen Sie keinen

Fehler.

(a) Die Öffnung zum Nachfüllen des

“BENZINGEMISCHS”

Position:

KRAFTSTOFFTANKDECKEL

(b) Die Richtung zum Schließen der

Drossel

Position:

LUFTFILTERABDECKUNG

Position:

LUFTFILTERABDECKUNG

Per un funzionamento e una

manutenzione sicura, i simboli sono stati

incisi in rilievo sull’apparecchio. Seguite

queste indicazioni per evitare eventuali

errori.

(a) Porta per riempire la miscela “MIX

GASOLINE”,

Posizione:

COPERCHIO DEL SERBATOIO DEL

CARBURANTE.

(b) Direzione di chiusura dell’aria

Posizione:

COPERCHIO DEL FILTRO DELL’ARIA

Posizione:

COPERCHIO DEL FILTRO DELL’ARIA

Para el uso y mantenimiento seguro del

producto, los símbolos han sido

estampados en relieve en la máquina.

Siga siempre estas indicaciones, y tenga

cuidado de no cometer un error.

(a) Orificio de llenado de “MEZCLA DE

GASOLINA”

Posición:

TAPÓN DEL TANQUE DE

COMBUSTIBLE

(b) Dirección de cierre del estrangulador

Posición:

CUBIERTA DEL FILTRO DE AIRE

estrangulador

Posición:

CUBIERTA DEL FILTRO DE AIRE

English Français

5. For safe operation

1. Read this manual carefully until you

completely understand and follow all

safety and operating instructions.

2. Keep this manual handy so that you

may refer to it later whenever any

questions arise. Also note, if you have

any questions which cannot be

answered herein, contact the dealer

from whom you purchased the

product.

3. Always be sure to include this manual

when selling, lending, or otherwise

transferring the ownership of this

product.

4. Never allow children or anyone

unable to fully understand the

directions given in the manual to use

the machine.

■ WORKING CONDITION

1. When using the product, you should

wear proper clothing and protective

equipment.

(1) Helmet

(2) Ear protectors

(3) Protection goggles or face protector

(4) Thick work gloves

(5) Non-slip-sole work boots

2. And you should carry with you.

(1) Attached tools and files

(2) Properly reserved fuel

(3) Spare blade

(4) Things to notify your working area

(rope, warning signs)

(5) Whistle (for collaboration or

emergency)

(6) Hatchet or saw (for removal of

obstacles)

3. Do not wear loose clothing, jewelry,

short trousers, sandals, or go barefoot.

Do not wear anything which might be

caught by a moving part of the unit.

Secure hair so it is above shoulder

length.

■ WORKING CIRCUMSTANCE

1. Never start the engine inside a closed

room or building. Exhaust gases

contain dangerous carbon monoxide.

2. Never use the product:

a. when the ground is slippery or when

you can’t maintain a steady posture.

b. At night, at times of heavy fog, or at

any other times when your field of

vision might be limited and it would

1. Lire ce manuel attentivement jusqu’à

une compréhension totale et suivre

toutes les instructions de sécurité et

d’utilisation.

2. Conserver ce mode d’emploi à portée

de la main pour le consulter au

moindre doute. Si une question reste

sans réponse, contacter le revendeur.

3. Ne pas oublier de donner le manuel

avec la machine en cas de revente ou

de prêt.

4. Ne pas laisser des enfants ou toute

personne incapable de comprendre

les instructions, utiliser cette machine.

■ CONDITIONS DE TRAVAIL

1. Lors de l’utilisation de cette machine, il

est nécessaire de porter des vêtements

appropriés et des équipements de

sécurité.

(1) Casque

(2) Casque antibruit

(3) Lunettes ou masque de protection

(4) Gants de travail épais

(5) Chaussures de sécurité à semelle

antidérapante

2. Les objets suivants doivent être

emportés sur le lieu de travail :

(1) Les outils fournis avec la machine et

des limes

(2) Une réserve de carburant

(3) Une lame de rechange

(4) Matériel pour délimiter la zone de

travail

(5) Un sifflet (pour collaborateur ou en

cas d’urgence)

(6) Une hache ou une scie (pour

enlever les obstacles)

3. Ne pas porter des vêtements lâches, de

short, de bijou, de sandales ou travailler

pieds nus. Ne pas porter quoi que ce

soit pouvant être happé par les pièces

en mouvement de la machine. Porter

les cheveux longs noués au-dessus des

épaules.

■ CONDITIONS DE TRAVAIL

1. Ne jamais mettre la machine en marche

à l’intérieur d’une pièce ou d’un

bâtiment. Les gaz d’échappement

contiennent du monoxide de carbone

dangereux.

2. Ne jamais utiliser la machine dans les

conditions suivantes:

a. Lorsque le sol est glissant ou lorsqu’il

est impossible de se maintenir dans

5. Consignes de securite

EspañolDeutsch Italiano

1. Lesen Sie sich diese Anleitung

sorgfältig durch, bis Sie alle

Sicherheits- und Bedienungshinweise

verstehen und befolgen.

2. Diese Anleitung greifbereit haben, um

sie im Zweifelsfall schnell zur Hand zu

haben. Bei Fragen zum Gerät, die

nicht in dieser Anleitung behandelt

werden, bitte an den Händler wenden,

der Ihnen das Produkt verkauft hat.

3. Bei Verkauf, Verleih oder Weitergabe

stets diese Anleitung zusammen mit

dem Gerät übergeben.

4. Niemals Kinder oder Personen, die

die Anweisungen in dieser Anleitung

nicht vollständig verstehen, die

Maschine betreiben lassen.

■ ARBEITSBEDINGUNG

1. Wenn das Produkt benutzt wird, sollten

Sie stets richtige Kleidung und

Schutzausrüstung tragen.

(1) Helm

(2) Ohrenschutz

(3) Schutzbrille oder Schutzmaske

(4) Dicke Schutzhandschuhe

(5) Rutschfeste Arbeitsschuhe

2. Und Sie sollten folgende Dinge bei sich

tragen.

(1) Mitgelieferte Werkzeuge und Feilen

(2) Reservekraftstoff

(3) Ersatzschneidblatt

(4) Gegenstände, die Ihren

Arbeitsbereich kennzeichnen (Seil,

Warnzeichen)

(5) Pfeife (für Zusammenarbeit oder

Notfall)

(6) Beil oder Säge (zum Entfernen von

Hindernissen)

3. Keine lockere Kleidung, Schmuck,

kurze Hosen oder Sandalen tragen und

nicht barfuß gehen. Nichts tragen, daß

von den beweglichen Teilen des

Gerätes erfaßt werden kann. Haare

über Schulterhöhe zusammenbinden.

■ ARBEITSUMSTAND

1. Den Motor niemals in geschlossenen

Räumen oder Gebäuden starten.

Abgase enthalten gefährliches

Kohlenmonoxid.

2. Niemals das Produkt benutzen:

a. wenn der Untergrund glitschig ist

oder ein stabiler Stand beeinträchtigt

ist.

b. Nachts, bei dichtem Nebel oder

1. Leggete questo manuale

attentamente per capire

completamente ed osservare tutte le

norme di sicurezza ed istruzioni per

l’uso.

2. Tenete questo manuale in un luogo

accessibile per poter fare riferimento

all stesso in un momento successivo,

in caso di dubbi. Inoltre, se avete

delle domande alle quali non trovate

la risposta nel manuale, rivolgetevi al

vostro rivenditore da cui avete

acquistato questo prodotto.

3. Assicuratevi di allegare questo

manuale se vendete o prestate l’unità

oppure se la stessa cambia

proprietario in altri modi.

4. Non lasciate mai che bambini o

persone non consapevoli delle

istruzioni fornite nel manuale

d’istruzioni utilizzino l’apparecchio.

■ CONDIZIONI LAVORATIVE

1. Quando usate il prodotto, dovete

indossare i vestiti e le protezioni

appropriate.

(1) Casco

(2) Cuffie di protezione

(3) Occhiali di protezione o visiera

(4) Spessi guanti di lavoro

(5) Scarponi di lavoro con la suola

antiscivolo

2. Inoltre, portate i seguenti oggetti con

voi:

(1) Gli utensili e le lime in dotazione

(2) Il carburante custodito in modo

appropriato

(3) Una lama di riserva

(4) Oggetti per delimitare l’area di

lavoro (una corda, delle insegne di

avvertimento)

(5) Un fischietto (per collaborazione o

per situazioni di emergenza)

(6) Accetta o sega (per rimuovere degli

ostacoli)

3. Non indossate dei vestiti lenti, gioielli,

pantaloncini, sandali, né camminate

scalzo. Non indossate nessun oggetto

che possa rimanere inceppato nelle

parti mobili dell’unità. Legate i capelli in

modo tale che sia al di sopra

dell’altezza delle spalle.

■ CIRCOSTANZE LAVORATIVE

1. Non accendete mai il motore all’interno

di una stanza chiusa o in un edificio. I

gasi di scarico contengono il monossido

di carbonio che è molto pericoloso.

2. Non usate mai il prodotto nelle seguenti

situazioni:

a. Quando il terreno è scivoloso o

quando non potete mantenere una

posizione stabile.

1. Lea detenidamente este manual

hasta comprender cabalmente todas

las instrucciones de seguridad y uso.

2. Mantenga este manual a mano para

que pueda consultarlo cuando tenga

alguna duda. Si tiene cualquier duda

que no esté cubierta en este manual,

consulte en la tienda donde adquirió

el producto.

3. Asegúrese de incluir siempre este

manual al vender, prestar o transferir

la propiedad de este producto.

4. Nunca permita que niños u otras

personas que no sean capaces de

comprender cabalmente las

instrucciones que se dan en el

manual utilicen la máquina.

■ CONDICIONES DE TRABAJO

1. Al utilizar el producto, asegúrese de

usar la vestimenta y el equipo de

protección adecuados.

(1) Casco

(2) Protectores para los oídos

(3) Gafas protectoras o protector facial

(4) Guantes de trabajo gruesos

(5) Botas de trabajo con suela

antideslizante

2 Asegúrese de llevar con usted los

siguientes elementos:

(1) Herramientas y limas incluidas

(2) Combustible de reserva

(3) Hoja de repuesto

(4) Elementos para marcar su área de

trabajo (cuerdas, letreros de

advertencia)

(5) Silbato (para colaboración o

situaciones de emergencia)

(6) Hacha pequeña o sierra (para quitar

obstáculos)

3. No use ropa suelta, joyas, pantalones

cortos ni sandalias, y no trabaje

descalzo. No use nada que pueda ser

atrapado por las piezas móviles de la

unidad. Recójase el pelo,

asegurándose de que quede por

encima de sus hombros.

■ PRECAUCIONES

1. Nunca arranque el motor dentro de una

habitación cerrada o edificio. Los gases

de escape contienen monóxido de

carbono peligroso.

2. Nunca use el producto en los siguientes

casos:

a. Cuando el suelo sea resbaloso o

cuando usted no pueda mantener

una posición estable.

5. Sicherer Betrieb

5. Per un funzionamento sicuro

5. Instrucciones de seguridad

English Français

be difficult to gain a clear view of the

working area.

c. During rain storms, during lightning

storms, at times of strong or gale-

force winds, or at any other times

when weather conditions might make

it unsafe to use the product.

■ WORKING PLAN

1. You should never use the product when

under the influence of alcohol, when

suffering from exhaustion or lack of

sleep, when suffering from drowsiness

as a result of having taken cold

medicine or at any other time when a

possibility exists that your judgment

might be impaired or that you might not

be able to operate the product properly

and in a safe manner.

2. When planning your work schedule,

allow plenty of time to rest. Limit the

amount of time over which the product

is to be used continuously to

somewhere around 30–40 minutes per

session, and take 10–20 minutes of rest

between work sessions. Also try to

keep the total amount of work

performed in a single day under 2 hours

or less.

1. If you don’t observe the working

time, or working manner (See

■USING THE PRODUCT), Repetitive

Stress Injury(RSI) could occur.

If you feel discomfort, redness and

swelling of your fingers or any other

part of your body, see a doctor

before getting worse.

2. To avoid noise complaints, in

general, operate product between

8a.m. and 5p.m. on weekdays and

9a.m. to 5p.m. weekends.

Check and follow the local regulations as

to sound level and hours of operations for

the product.

■ BEFORE STARTING THE ENGINE

1. The area within a perimeter of 15 m of

the person using the product should be

considered a hazardous area into which

no one should enter. If necessary

yellow warning rope, warning signs

should be placed around the perimeter

of the area. When work is to be

NOTE

WARNING

une position correcte.

b. La nuit, par temps de brouillard ou

lorsque la visibilité ou le champ de

vision empêche de voir clairement la

zone de travail.

c. Pendant les averses, les orages

avec éclairs, par grands vents ou

toute autre condition climatique

rendant l’utilisation de la machine

dangereuse.

■ PLAN DE TRAVAIL

1. Ne jamais utiliser la machine sous

l’influence de l’alcool ou en état de

faiblesse due à la fatigue, au manque

de sommeil, à la prise de médicament

ou à tout autre moment où l’on n’est

pas réellement capable de l’utiliser

correctement et en toute sécurité.

2. Lors de l’élaboration du plan de travail,

prévoir suffisamment de temps de

repos. Limiter la durée des périodes

pendant lesquelles la machine est

utilisée sans interruption entre 30 et 40

minutes. Se reposer de 10 à 20 minutes

entre ces périodes. Autant que

possible, essayer de limiter ce genre de

travail à 2 heures par jour.

1. Si ce plan de travail et cette méthode

de travail ne sont pas respectés, un

accident dû au stress répétitif peut

se produire (voir ■UTILISATION DE

LA MACHINE).

Si l’on ressent un malaise ou si les

doigts ou tout autre membre

rougissent et enflent, consulter un

docteur avant que cela ne s’aggrave.

2. Pour éviter les problèmes de bruit

avec le voisinage, utiliser

généralement la machine entre 8 et

17 heures pendant la semaine et de 9

à 17 heures les fins de semaine.

Vérifier et suivre la réglementation locale

sur le niveau de bruit et les horaires

d’utilisation de ce type de machine.

■ AVANT DE METTRE LE MOTEUR EN

MARCHE

1. La zone dans un rayon de 15 mètres

autour de l’opérateur est considérée

comme dangereuse et personne ne doit

s’y trouver. Si nécessaire, délimiter le

périmètre de la zone de travail avec du

ruban de marquage (rouge fluorescent

REMARQUE

AVERTISSEMENT

5. For safe operation 5. Consignes de securite

EspañolDeutsch Italiano

anderen Bedingungen, die die Sicht

im Arbeits- und Sicherheitsbereich

einschränken und einen sicheren

Betrieb verhindern.

c. Bei starkem Niederschlag, Gewitter,

stürmischem Wind oder anderen

Wetterbedingungen, die einen

sicheren Einsatz dieses Produktes

unmöglich machen.

■ ARBEITSPLAN

1. Sie sollten das Produkt keinesfalls unter

Einfluß von Alkohol, bei Erschöpfung

oder Übermüdung, bei Schläfrigkeit

aufgrund der Einnahme von

Erkältungsmitteln oder dann benutzen,

wenn die Möglichkeit besteht, daß Ihr

Urteilsvermögen beeinträchtigt ist oder

Sie nicht imstande sind, das Produkt

einwandfrei und sicher zu bedienen.

2. Beim Planen der Arbeitseinsätze,

genügend Ruhephasen

berücksichtigen. Begrenzen Sie die

Zeitdauer, die die vorgesehenen 30 –

40 Minuten pro Arbeitseinsatz bei

kontinuierlichem Betrieb überschreitet

und zwischen den Einsätzen jeweils

Pausen von 10 – 20 Minuten einlegen.

Die gesamte Arbeitszeit sollte täglich

unter 2 Stunden oder weniger liegen.

1. Wenn Sie die Arbeitszeit oder die

Arbeitsweise nicht beachten (Siehe

■ANWENDUNG DES PRODUKTS),

könnten Verletzungen aufgrund sich

wiederholenden Stresses (RSI)

verursacht werden.

Wenn Sie sich nicht wohl fühlen,

wenn Ihre Finger oder ein anderes

Körperteil rot und angeschwollen ist,

suchen Sie einen Arzt auf, bevor es

schlimmer wird.

2. Um Lärmbelästigung zu verhindern

sollte das Gerät im allgemeinen

werktags zwischen 8.00 und 17.00

und am Wochenende zwischen 9.00

und 17.00 Uhr verwendet werden.

Prüfen und befolgen Sie die örtlichen

Bestimmungen für dieses Produkt und die

Betriebsstunden.

■ VOR DEM START DES MOTORS

1. Der Gefahrenbereich während des

Betriebs, aus dem Dritte unbedingt

fernzuhalten sind, erstreckt sich in

einem Umkreis von 15 Metern, um

dieses Produkt. Falls erforderlich, den

Arbeitsbereich mit einem gelben

Warnband, mit Warnzeichen absperren.

HINWEIS

WARNUNG

b. Di notte, quando c’è molta nebbia o

in altre occasioni quando il campo

visivo è limitato ed è difficile avere

una visione nitida dell’area di lavoro.

c. Durante la pioggia, durante una

tempesta, quando tira un vento molto

forte o in altre occasioni in cui le

condizioni meteorologiche rendono

poco sicuro l’utilizzo del prodotto.

■ PIANO DI LAVORO

1. Non usate mai il prodotto sotto

l’influenza dell’alcool, se siete stanchi o

assonnati; se siete in uno stato di

sonnolenza per via dell’assunzione di

farmaci o in altre occasioni in cui vostro

giudizio può essere ridotto,

impedendovi così di usare il prodotto in

modo corretto e sicuro.

2. Quando pianificate il lavoro, non

dimenticate di fornire del tempo per

riposare. Limitate il tempo di utilizzo del

prodotto a 30 — 40 minuti per sessione

e riposatevi da 10 a 20 minuti tra le

sessioni di lavoro. Inoltre, cercate di

mantenere la quantità totale del lavoro

effettuato durante la giornata a 2 ore o

meno.

1. Se non osservate il tempo di lavoro o

il modo di lavoro. (Fate riferimento

alla sezione ■ UTILIZZO DEL

PRODOTTO), si possono verificare

delle lesioni per via di sforzi continui

(RSI). Se sentite del disagio, oppure

se le dita od altre parti del corpo si

arrossiscono o si gonfiano,

consultate un medico prima che la

situazione peggiora.

2. Per evitare dei problemi dovuti alla

generazione di rumore, usate il

prodotto tra le ore 8 antimeridiane e

le ore 5 pomeridiane nei giorni feriali

e dalle ore 9 antimeridiane e le 5

pomeridiane nei giorni festivi.

Controllate ed osservate le norme locali

sul livello sonoro e sulle ore operative del

prodotto.

■ PRIMA DI ACCENDERE IL MOTORE

1. L’area all’interno di un perimetro di 15

m dalla persona usando il prodotto va

considerata una zona pericolosa in cui

nessuno deve entrare. Se necessario,

posizionare una corda di avvertimento

di colore giallo oppure delle insegna di

avvertimento intorno all’area. Quando il

NOTA

AVVERTIMENTO

b. Durante la noche, cuando haya

niebla densa, o en cualquier otra

situación en que su campo de visión

esté limitado y sea difícil lograr una

adecuada visión del área de trabajo.

c. Durante tormentas de lluvia,

tormentas eléctricas, tormentas de

viento, o en cualquier otra

circunstancia en que las condiciones

climáticas puedan hacer inseguro el

uso del producto.

■ PLAN DE TRABAJO

1. Nunca utilice el producto cuando se

encuentre bajo la influencia del alcohol,

cuando sufra de fatiga o falta de sueño,

cuando sienta somnolencia debido a

que ha tomado una medicina para el

resfrío, o en cualquier otra situación

que pueda afectar su juicio y usted no

sea capaz de utilizar el producto

correctamente y de manera segura.

2. Al planificar su trabajo, deje un tiempo

suficiente para descansar. Limite el

tiempo de uso continuo del producto a

30–40 minutos por sesión, y tome

descansos de 10–20 minutos entre las

sesiones de trabajo. Asimismo, trate de

que la cantidad total de trabajo diario

sea inferior a 2 horas.

1. Si no sigue las recomendaciones en

cuanto a la duración del trabajo o a

la forma de trabajar (consulte ■USO

DEL PRODUCTO), usted podrá sufrir

una lesión por esfuerzo repetido

(RSI).

Si siente algún malestar, si sus

dedos o cualquier otra parte de su

cuerpo enrojecen o se hinchan,

consulte oportunamente a un

médico.

2. Para evitar problemas de ruido, en

general utilice el producto entre las 8

a.m. y las 5 p.m. los días laborables,

y de 9 a.m. a 5 p.m. durante el fin de

semana.

Compruebe y respete las disposiciones

locales respecto de los niveles de ruido y

horas de uso del producto.

■ ANTES DE ARRANCAR EL MOTOR

1. El área dentro de un perímetro de 15 m

de la persona que está usando el

producto debe considerarse como un

área de peligro en la que nadie debe

ingresar. Si fuera necesario, marque el

perímetro del área de trabajo con una

cuerda de color amarillo y letreros de

NOTA

ADVERTENCIA

5. Sicherer Betrieb

5. Per un funzionamento sicuro

5. Instrucciones de seguridad

English Français

performed simultaneously by two or

more persons, care should also be

taken to constantly look around or

otherwise check for the presence and

locations of other people working so as

to maintain a distance between each

person sufficient to ensure safety.

2. Check the condition of working area to

avoid any accident by hitting hidden

obstacles such as stumps, stones,

cans, or broken grass.

Remove any obstacle before beginning

work.

3. Inspect the entire unit for loose

fasteners and fuel leakage. Make sure

that the cutting attachment is properly

installed and securely fastened.

4. Be sure the debris guard is firmly

attached in place.

5. Always use the shoulder strap. Adjust

the strap for comfort before starting the

engine. The strap should be adjusted

so the left hand can comfortably hold

the handlebar grip approximately waist

high.

■ STARTING THE ENGINE

1. Keep bystanders and animals at least

15 m away from the operating point. If

you are approached, immediately stop

the engine.

2. The product is equipped with a

centrifugal clutch mechanism, so the

cutting attachment begins to rotate as

soon as the engine is started by putting

the throttle into the start position. When

starting the engine, place the product

onto the ground in a flat clear area and

hold it firmly in place so as to ensure

that neither the cutting part nor the

throttle come into contact with any

obstacle when the engine starts.

Never place the throttle into the high

speed position when starting the

engine.

3. After starting the engine, check to make

sure that the cutting attachment stops

rotating when the throttle is moved fully

back to its original position. If it

continues to rotate even after the

throttle has been moved fully back, turn

WARNING

IMPORTANT

et blanc par exemple) et poser des

panneaux d’avertissement. Lorsque

deux ou plusieurs personnes travaillent

ensemble ou à proximité, chacune doit

constamment faire attention et garder

ses distances par rapport aux autres

pour assurer une sécurité satisfaisante.

2. Vérifier constamment l’état de la zone

de travail pour éviter tout accident dû

aux impacts avec des obstacles tels

que les souches, les pierres, les boîtes

de conserves ou débris de verre.

Retirer tout obstacle avant de commencer

le travail.

3. Vérifier que la machine ne comporte

aucun élément desserré ou de fuite de

carburant. S’assurer que l’outil de

coupe est monté correctement et bien

serré.

4. S'assurer que le cache de protection

anti-débris est fermement attaché.

5. Utiliser toujours la machine avec son

harnais. Le régler pour un confort

maximal avant de mettre le moteur en

marche. Il doit être ajusté pour que la

main gauche puisse tenir

confortablement la poignée environ à

hauteur de la taille.

■ DEMARRAGE DU MOTEUR

1. Empêcher toute personne ou animal de

s’approcher à moins de 15 mètres. Si

quelqu’un s’approche trop près, arrêter

aussitôt le moteur.

2. La machine est équipée d’un

embrayage centrifuge et l’outil de coupe

se met à tourner dès que le moteur est

mis en route en plaçant l’accélérateur

en position de démarrage. Pour mettre

le moteur en route, poser et maintenir

fermement la machine à plat sur le sol

dans un endroit dégagé où aucun

obstacle ne peut entrer en contact avec

l’outil de coupe ou la manette

d’accélérateur une fois que le moteur

sera en marche.

Ne jamais mettre la manette de

l’accélérateur à fond lors de la mise en

marche.

3. Une fois le moteur en marche, vérifier

que l’outil de coupe s’arrête de tourner

lorsque l’accélérateur est remis à zéro.

Si l’outil de coupe continue à tourner,

arrêter le moteur et rapporter la

AVERTISSEMENT

IMPORTANT

5. For safe operation 5. Consignes de securite

EspañolDeutsch Italiano

Sollten mehrere Personen gleichzeitig

in demselben Bereich arbeiten, stets

auf ausreichenden Abstand achten, um

die Sicherheit aller Mitarbeiter zu

gewährleisten.

2. Den Zustand des Arbeitsbereiches

prüfen, um einen Unfall aufgrund

versteckter Hindernisse wie Stümpfe,

Steine oder zerbrochenes Glas

vermieden werden.

Hindernisse vor Arbeitsbeginn

wegräumen.

3. Prüfen Sie das gesamte Gerät auf

lockere Befestigungen und

Kraftstofflecks. Sicherstellen, daß das

Schneidblatt richtig installiert und fest

fixiert ist.

4. Stellen Sie sicher, daß der Abfallschutz

fest in Position befestigt ist.

5. Immer den Schultergurt verwenden.

Den Gurt vor dem Starten des Motors

so einstellen, daß er beim Betrieb nicht

stört und daß die linke Hand den

Handgriff ohne Probleme ca. auf

Hüfthöhe halten kann.

■ DEN MOTOR STARTEN

1. Zuschauer und Tiere mindestens 15

Meter vom Arbeitsbereich fernhalten.

Wenn sich Ihnen jemand nähert, sofort

den Motor stoppen.

2. Das Produkt verfügt über einen

Zentrifugalkupplungsmechanismus.

Dadurch beginnt sich das Schneidblatt

zu drehen, sobald der Drosselhebel in

die Startposition gebracht wird. Beim

Starten des Motors, das Produkt auf

einen ebenen Boden stellen und

festhalten, so daß das Schneidteil und

die Drossel bei Start des Motors nicht in

Kontakt mit Fremdkörpern kommen.

Niemals die Drossel in die

Schnellaufposition bewegen, wenn der

Motor gestartet wird.

3. Nach dem Starten des Motors

sicherstellen, daß das Blatt stoppt,

wenn die Drossel zurück in die

Ausgangsposition bewegt wird. Sollte

sich das Blatt weiterhin bewegen, den

Motor sofort abstellen und das Gerät

zur Reparatur einem autorisierten

WARNUNG

WICHTIG

lavoro deve essere eseguito

contemporaneamente da due o più

persone, controllate continuamente la

posizione delle altre persone che

lavorano per mantenere una distanza di

sicurezza tra ciascuna persona,

garantendo così l’incolumità di tutti.

2. Controllate la condizione dell’area di

lavoro per evitare eventuali incidenti

dovuto al contatto con degli ostacoli

nascosti, ad esempio ceppi d’albero,

sassi, bidoni o pezzi di vetro rotto.

Rimovete eventuali ostacoli prima di

cominciare il lavoro.

3. Ispezionate l’intera unità per scoprire

eventuali dispositivi di fissaggi lenti o

eventuali perdite di carburante.

Assicuratevi che la testa tagliente sia

stata installata e fissata in modo ben

saldo.

4. Assicuratevi che la protezione anti-

detriti sia ben salda in posizione.

5. Usate sempre la tracolla. Regolate la

tracolla prima di accendere il motore.

La tracolla va regolata in modo tale che

possiate tenere comodamente con la

mano sinistra l’impugnatura all’altezza

del fianco.

■ ACCENSIONE DEL MOTORE

1. Assicuratevi che le persone e gli

animali si trovino ad una distanza di

almeno 15 metri dal punto di lavoro. Se

vi si avvicinano, spegnete il motore

immediatamente.

2. Il prodotto è stato dotato di un

meccanismo ad innesto centrifugale, in

modo tale che la testa tagliante inizia a

girare appena si accende il motore

posizionando la leva del gas nella

posizione di avviamento. Prima di

accendere il motore, posizionate il

prodotto sul terreno in un luogo piano e

privo di ostacoli e tenetelo fermo nella

posizione per assicurarvi che né la

parte tagliente né la leva del gas venga

in contatto con eventuali ostacoli

quando si accende il motore.

Non posizionate mai la leva del gas

nella posizione ad alta velocità per

accendere il motore.

3. Dopo aver acceso il motore, controllate

che la testa tagliente smetta di ruotare

appena si rimette la leva del gas nella

AVVERTIMENTO

IMPORTANTE

advertencia. Cuando el trabajo vaya a

ser realizado simultáneamente por dos

o más personas, también se deberá

tener la precaución de mirar

constantemente alrededor y verificar la

presencia y posición de las demás

personas que están trabajando, a fin de

mantener una distancia prudente entre

cada persona que garantice su

seguridad.

2. Compruebe las condiciones del área de

trabajo a fin de evitar accidentes que

pueden ocurrir al golpear obstáculos

ocultos tales como tocones, piedras,

latas o vidrios rotos.

Quite todos los obstáculos antes de iniciar

el trabajo.

3. Inspeccione la unidad completa para

determinar si tiene sujetadores sueltos

o fugas de combustible. Asegúrese de

que el accesorio de corte esté

debidamente instalado y asegurado.

4. Asegúrese de que el protector contra

desechos se encuentra firmemente

acoplado en su sitio.

5. Utilice siempre la correa de hombro.

Ajuste la correa a su comodidad antes

de arrancar el motor. La correa debe

ajustarse de tal forma que la mano

izquierda pueda sujetar cómodamente

la barra del manillar aproximadamente

a la altura de la cintura.

■ ARRANQUE DEL MOTOR

1. Mantenga a espectadores y animales a

una distancia de al menos 15 metros

del lugar de uso de la máquina. Si

alguien se aproxima, detenga

inmediatamente el motor.

2. El producto está equipado con un

mecanismo de embrague magnético,

por lo que el accesorio de corte

comienza a girar inmediatamente

cuando se arranca el motor poniendo el

acelerador en posición de arranque. Al

arrancar el motor, ponga el producto en

el suelo, en un lugar plano y despejado,

y sujételo firmemente para asegurarse

de que la pieza de corte y el acelerador

no puedan entrar en contacto con

ningún obstáculo cuando el motor

arranque.

Nunca ponga el acelerador en la

posición de alta velocidad al arrancar

el motor.

3. Después de arrancar el motor,

compruebe que el accesorio de corte

deja de girar cuando usted devuelve

ADVERTENCIA

IMPORTANTE

5. Sicherer Betrieb

5. Per un funzionamento sicuro

5. Instrucciones de seguridad

English Français

off the engine and take the unit to your

authorized Komatsu Zenoah servicing

dealer for repair.

■ USING THE PRODUCT

Cut only materials recommended by

the manufacturer. And use only for

tasks explained in the manual.

1. Grip the handles firmly with both hands

using your whole hand. Place your feet

slightly apart (slightly further apart than

the width of your shoulders) so that

your weight is distributed evenly across

both legs, and always be sure to

maintain a steady, even posture while

working.

2. Keep cutting attachment below waist

level.

3. Maintain the speed of the engine at the

level required to perform cutting work,

and never raise the speed of the engine

above the level necessary.

4. If the unit start to shake or vibrate, turn

off the engine and check the whole unit.

Do not use it until the trouble has been

properly corrected.

5. Keep all parts of your body away from

rotating cutting attachment and hot

surfaces.

6. Never touch the muffler, spark plug, or

other metallic parts of the engine while

the engine is in operation or

immediately after shutting down the

engine. Doing so could result in serious

burns or electrical shock.

• IF SOMEONE COMES

1. Guard against hazardous situations at

all times. Warn adults to keep pets and

children away from the area. Be careful

if you are approached. Injury may result

from flying debris.

2. If someone calls out or otherwise

interrupts you while working, always be

sure to turn off the engine before

turning around.

■ MAINTENANCE

1. In order to maintain your product in

proper working order, perform the

IMPORTANT

machine chez le revendeur agréé pour

la faire réparer.

■ UTILISATION DE LA MACHINE

Ne couper avec la machine que les

matériaux recommandés par le

fabricant.

1. Tenir les poignées de la machine

fermement des deux mains. Ecarter

légèrement les jambes (pour que les

pieds reposent sur une largeur un peu

plus importante que celle des épaules)

et avoir une posture de travail stable et

répartir le poids du corps également sur

chaque jambe.

2. Maintenir l’outil de coupe toujours plus

bas que le niveau de la taille.

3. Faire tourner le moteur à la vitesse

appropriée à la coupe sans jamais

accélérer inutilement au dessus du

niveau nécessaire.

4. Si la machine se met à vibrer ou à créer

des secousses, arrêter le moteur et

procéder à une vérification totale de la

machine.

5. Se tenir à distance de l’outil de coupe

ou des parties chaudes de la machine.

6. Ne jamais toucher le silencieux, la

bougie ou toute autre partie métallique

du moteur pendant le fonctionnement

ou aussitôt après son arrêt. Dans ces

circonstances, les risques de brûlures

ou d’électrocution sont importants.

• SI QUELQU’UN S’APPROCHE

1. Il faut se préserver des situations

dangereuses à tout moment. Avertir les

adultes de maintenir les enfants et les

animaux à distances car le risque de

recevoir des projections d’objet est

important.

2. Si quelqu’un appelle ou interrompt le

travail d’une manière ou d’une autre,

arrêter le moteur avant de se tourner

vers la personne.

■ ENTRETIEN

1. De manière à conserver la machine en

parfait état de marche, effectuer à

IMPORTANT

5. For safe operation 5. Consignes de securite

La page charge ...

ZENOAH KOMATSU TR2000 Manuel utilisateur

Marque: ZENOAH KOMATSU

Modèle: TR2000

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

italiano: ZENOAH KOMATSU TR2000 Manuale utente
English: ZENOAH KOMATSU TR2000 User manual
español: ZENOAH KOMATSU TR2000 Manual de usuario
Deutsch: ZENOAH KOMATSU TR2000 Benutzerhandbuch

Documents connexes

ZENOAH KOMATSU BCX2601DL Manuel utilisateur

ZENOAH KOMATSU TR2000 Manuel utilisateur

Ce manuel convient également à

ZENOAH KOMATSU TR2000 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents