Senco DS222-18V Le manuel du propriétaire

Marque: Senco

Modèle: DS222-18V

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

DS222-18V

DS225-18V

DS322-18V

AUTO-FEED

SCREWDRIVER

Operating Instructions

KYOCERA SENCO Industrial Tools

4270 Ivy Pointe Blvd.

Cincinnati, OH 45245

1-800-543-4596

www.senco.com

NFD810A10B10C • Issued November 4, 2019

IMPORTANT: Read before use.

Table of Contents

Symbols .................................................................................................................................... 3

General Power Tool Safety Warnings ...................................................................................... 4

Work Area Safety ................................................................................................................... 4

Electrical Safety ..................................................................................................................... 4

Personal Safety ..................................................................................................................... 4

Power Tool Use and Care ...................................................................................................... 5

Battery Tool Use and Care ..................................................................................................... 5

Service .................................................................................................................................. 6

Screwdriver Safety Warnings .................................................................................................. 6

Safety Warnings for Charger and Battery ................................................................................ 6

Functional Description ............................................................................................................. 8

Tool Operation .......................................................................................................................... 9

Adjusting for Fastener Length ............................................................................................... 9

Loading the Tool .................................................................................................................... 9

Drive Speed Adjustment ...................................................................................................... 10

Driving Screws .................................................................................................................... 10

Trigger Lock ........................................................................................................................ 10

Depth of Drive Adjustment .................................................................................................. 10

Reverse Operation ............................................................................................................... 11

Bit Replacement .................................................................................................................. 11

Nosepiece Replacement ...................................................................................................... 12

Belt Hook Adjustment .......................................................................................................... 12

Battery Pack Installation ...................................................................................................... 12

Battery Pack Removal ......................................................................................................... 13

Battery Charging .................................................................................................................. 13

Battery Disposal .................................................................................................................. 14

Maintenance .......................................................................................................................... 14

Accessories ............................................................................................................................ 14

Technical Speciﬁcations ........................................................................................................ 15

Troubleshooting ..................................................................................................................... 16

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated

with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in

death or serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in

death or serious injury.

CAUTION:

Indicates a hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) indicates information considered im-

portant, but not related to a potential injury (e.g. messages relating

to property damage).

Some of the following symbols may be used on this product. Please study them and learn their meaning.

Proper interpretation of these symbols will allow you to operate the product in a better, safer manner.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert

Indicates a potential personal injury hazard.

Read Operator’s

Manual

To reduce the risk of injury, user must read and understand opera-

tor’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply with

ANSI Z87.1.

Wet Conditions

Alert

Do not expose to rain or use in damp locations.

No Hands

Failure to keep your hands away from blade will result in serious

personal injury.

Recycle

This product uses Lithium-ion batteries. Local, state, or federal laws

may prohibit disposal of batteries in ordinary trash. Consult your

local waste authority for information regarding available recycling

and or disposal options.

V Volts

Voltage

min Minutes

Time

Direct Current

Type or characteristic of current

No Load Speed

Rotational speed, at no load

.../min Per Minute

Revolutions, strokes, surface speed, orbits, etc. per minute

General Power Tool Safety Warnings

WARNING

Read all safety warnings, instructions, illustrations and speciﬁcations

provided with this power tool. Failure to follow all instructions listed below may result in electric

shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

WORK AREA SAFETY

1. Keep work area clean and well lit. Cluttered or dark areas promote accidents.

2. Do not operate power tools in explosive atmospheres, such as in the presence of ﬂammable liquids,

gases or dust. Power tools create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

ELECTRICAL SAFETY

4. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodiﬁed plugs and matching outlets will reduce risk of

electric shock.

5. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigera-

tors. There is an increased risk of electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

8. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

9. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

PERSONAL SAFETY

10. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use

a power tool while you are tired or under the inﬂuence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal injury.

11. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

12. Prevent unintentional starting. Ensure the switch is in the off position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your ﬁnger on the

switch or energizing power tools that have the switch on invites accidents.

13. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal injury.

14. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power

tool in unexpected situations.

15. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

16. If devices are provided for the connection of dust extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can reduce dust-related hazards.

17. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool

safety principles. A careless action can cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

18. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do

the job better and faster at the rate for which it was designed.

19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

20. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the pow-

er tool before making any adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

21. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

22. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by poorly maintained power tools.

23. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

24. Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into

account the working conditions and the work to be performed. Use of the power tool for operations

different from those intended could result in a hazardous situation.

25. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

26. Recharge only with the charger speciﬁed by the manufacturer. A charger that is suitable for one type of

battery pack may create a risk of ﬁre when used with another battery pack.

27. Use power tools only with speciﬁcally designated battery packs. Use of any other battery packs may

create a risk of injury and ﬁre.

28. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns or a ﬁre.

29. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally

occurs, ﬂush with water. If liquid comes into contact with eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or burns.

30. Do not use a battery pack or tool that is damaged or modiﬁed. Damaged or modiﬁed batteries may

exhibit unpredictable behaviour resulting in ﬁre, explosion or risk of injury.

31. Do not expose a battery pack or tool to ﬁre or excessive temperature. Exposure to ﬁre or temperature

above 130 °C may cause explosion.

GENERAL POWER TOOL SAFETY WARNINGS

32. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range

speciﬁed in the instructions. Charging improperly or at temperatures outside the speciﬁed range may

damage the battery and increase the risk of ﬁre.

SERVICE

33. Have your power tool serviced by a qualiﬁed repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

34. Never service damaged battery packs. Service of battery packs should only be performed by the manufac-

turer or authorized service providers.

Screwdriver Safety Warnings

1. Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener

may contact hidden wiring. Fasteners that come into contact with a “live” wire may make exposed metal

parts of the power tool “live” and could give the operator an electric shock.

2. Do not use the power tool in locations where the ambient temperature may reach 0°C (32°F) or exceed

40˚C (105˚F).

Safety Warnings for Charger and Battery

1. This manual contains important safety and operating instructions for the SENCO battery charger VB0156

and VB0189. Use with approved Senco batteries stated on the charger label.

2. Before using the SENCO battery charger VB0156 and VB0189, read all instructions and cautionary mark-

ings on (1) battery charger, (2) battery, and (3) product using battery.

3. Do not expose charger to water, rain or snow.

4. Use indoors.

5. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of

ﬁre, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting

charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage

or stress.

Length of Cord (Feet)

AWG Size of Cord

25 50 100 150

16 16 16 14

Table 1 - Recommended minimum AWG size for battery charger extension cords.

8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could

result in a risk of ﬁre and electric shock. If extension cord must be used, make sure:

a. That pins on plug of extension cord are the same number, size, and shape as those of plug

on charger;

GENERAL POWER TOOL SAFETY WARNINGS

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is at least as large as the one speciﬁed in the table.

9. Do not operate charger with damaged cord or plug- replace them immediately.

10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way;

take it to a SENCO Authorized Service Centre.

11. Do not disassemble charger or battery cartridge; take it to a SENCO Authorized Service Centre when

service or repair is required. Incorrect reassembly may result in a risk of electric shock or ﬁre.

12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.

13. Store battery packs in a 30%-50% charged condition.

14. Every six months of storage charge the pack as normal.

15. For best results, your battery should be charged in a location where the temperature is above 50˚F

but below 100˚F.

16. Do not store outside or in vehicles.

17. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.

18. Do not allow anything to cover or clog the charger vents.

19. Do not recharge non-rechargeable batteries.

20. This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instructions concerning use of the appliance by a person responsible for

their safety.

21. Children should be supervised to ensure that they do no play with the appliance.

22. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualiﬁed persons to avoid a hazard.

23. A battery short can cause a large current ﬂow, overheating, possible burns and even a breakdown.

a. Do not touch the terminals with any conductive material.

b. Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.

c. Do not expose battery cartridge to excessively humid conditions, water, snow or rain.

24. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed

27˚C (80˚ F).

25. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery

cartridge can explode in a ﬁre.

26. Do not use tool without Warning Label on tool. If label is missing, damaged or unreadable,

contact your SENCO representative to obtain a new label at no cost.

27. Never attempt to connect two (2) chargers together. Consecutive charging may cause overheating. If you

need to recharge batteries consecutively, wait about 15 minutes for the charger to cool.

28. Battery leakage may occur under conditions of extreme usage or temperature. If liquid comes in contact

with skin, wash quickly with soap and water, then with lemon juice or vinegar. If liquid gets in your eyes,

wash with water for at least 10 minutes and seek medical attention immediately.

SAFETY WARNINGS FOR CHARGER AND BATTERY

Tool-less Nosepiece

Adjustment Pin

Detachable Auto-Feed System

Locking Collar

LED Light

Variable Speed Trigger

Strip Guide Track

Drive Speed Adjustment

1600/2500 RPM

(Low Speed Tools Only)

Depth of Drive Adjustment Knob

Forward/Reverse Switch

Depth of Drive Lock Button

Slide Body Loading Point

Nosepiece Retention Screw

Strip Guide

(Only on DS322)

Depth of Drive Indicator

Bit Quick Release

Adjustable and

Reversible Belt Hook

18V Battery

(3Ah Shown)

Trigger Lock

Grasping Surface

Functional Description

Figure 1 - Tool Functions and Features

Tool Operation

Read sections titled “Safety Warnings” before operating tool.

For best results, charge new battery before using (see “Battery Charging” page #11).

WARNING

Do not use this product if it is not completely assembled or if any parts

appear to be missing or damaged. Use of a product that is not properly and completely

assembled or with damaged or missing parts could result in serious personal injury.

WARNING

Do not attempt to modify this product or create accessories or attachments not

recommended for use with this product. Any such alteration or modiﬁcation is misuse

and could result in hazardous conditions possibly leading to serious personal injury.

I any parts are damaged or missing, please call 1-800-543-4596 for assistance.

ADJUSTING FOR FASTENER LENGTH

1. Remove battery before adjusting nosepiece for fastener length.

2. Depress the screw selector pin until it is ﬂush with nosepiece and slide the nosepiece to the desired

setting by aligning hatch marks with the silver adjustment pin.

3. Release pin and make sure it is fully engaged in selected nosepiece slot for proper operation

DS222-18V DS225-18V DS322-18V

1 1/4"

1 1/2"

1 3/4"

1 5/8"

1 1/4"

1 1/2"

1 3/4"

1 5/8"

1 1/4"

1 1/2"

1 3/4"

1 5/8"

2 1/4"

2 1/2"

2 3/4"

Bit Type DS222/DS225 DS322

Phillips

Square

Rex

EA0297

EA0298

EA0299

EA0400

EA0401

EA0402

1-1/2

1-5/8

1-1/4

1-3/4

LOADING THE TOOL

1. Check to be sure the heads of the screws are resting on top of the plastic collation material.

This will ensure proper strip advancement and prevent jamming.

1 52

2. Check for proper fastener length setting (see “Adjusting for Fastener Length” above).

3. Feed the strip into the strip guide track up toward the nose of the tool.

4. Feed the strip into the slide body until the ﬁrst screw is aligned with the bit. The tool will feed all

subsequent screws automatically as the tool is pulled back off the work surface, returning to its

relaxed state.

5. To remove the strip, pull it through from the top of the side body.

DRIVE SPEED ADJUSTMENT

Low speed tools can be switched from 2500 to 1600 RPM for driving self-drilling and tapping screws

into heavy steel applications. This can be done by depressing the drive speed adjustment button shown

in Figure 1. A red LED will indicate that low speed mode (1600 RPM) is engaged. Click the button again

to toggle back to normal mode (2500 RPM).

The most recently selected mode will be maintained indeﬁnitely until the user presses the button again.

DRIVING SCREWS

1. Whenever possible, hold the tool at a right angle to the work surface.

2. Pull the trigger to start the motor.

3. Press the nosepiece with constant force against the work surface. Do not remove the tool from the

work surface until the clutch disengages and the bit stops rotating, signalling a fully driven screw.

4. Continue to allow the motor to run. The next screw will be automatically fed into place when the tool

is pulled off the work surface.

CAUTION

During the driving process it is possible for the tool to “cut-out” or stop the motor

prematurely as a safety function to preserve the tool. If the motor senses a torque spike, an over-current

protection function will activate. A partially driven screw can be driven fully by squeezing the trigger

again to reset the tool/motor. If this cut-out occurs repeatedly, please review the troubleshooting sec-

tion for more details, or discontinue use in that application.

TRIGGER LOCK

To lock the trigger for continuous operation, depress the trigger and push in the locking button then

release the trigger. The tool will continue to run. To turn off, squeeze and release the trigger.

DEPTH OF DRIVE ADJUSTMENT

This tool is equipped with a locking depth control adjustment:

1. Release the thumbwheel by depressing the red lock button.

2. Adjust the countersink by turning the depth adjustment thumbwheel.

3 Refer to the markings on the tool for proper direction.

4. Release the lock button after adjustment.

Test drive screws while adjusting until the desired countersink is reached.

This tool has a depth-sensing clutch. When the screw is countersunk to the preset depth, it

automatically disengages and makes a click or ratcheting sound. This is normal and signals completion

of the drive.

TOOL OPERATION

CAUTION

When the battery is low, or the drive requires too much torque, the tool may stall at

the bottom of the drive (before the clutch can disengage). The same procedure should be followed

as mentioned above for tool cut-out.

REVERSE OPERATION

WARNING

To prevent the feed system from unintentionally falling off the tool, ensure the locking

collar is at the locked position before starting to drive screws or when carrying tools.

To operate tool in reverse for removal of screws (see Figure 1):

1. Flip the forward/reverse switch to the right for reverse rotation.

2. Turn the locking collar on the detachable feed system to the unlock position.

Locked Unlocked

3. Slide the feed system off the tool to expose the bit.

4. Insert bit into screw and apply/maintain pressure to engage clutch.

5. Pull trigger until screw is completely disengaged.

BIT REPLACEMENT

Due to wear or damage, the bit will need to be replaced periodically or when changing between drive

types.

The bit can be removed/replaced in two ways:

1. Without removing feed system

i. Remove fasteners from the tool.

ii. Slide bit release button to rear.

iii. Tilt tool forward and pulse trigger.

iv. Bit will fall out.

v. Hold tool upright.

vi. Insert the new bit into the slide body.

vii. Slide bit release button to rear.

viii Pulse tool and release button when bit drops into place.

2. Removal of tool front end/feed system

i. Turn the locking collar on the detachable feed system to the unlock position.

ii. Slide the feed system off the tool to expose the bit.

iii. Slide bit release button to rear.

iv. Pull the old bit out and release button.

v. Insert the new bit into the bit retainer and push until it clicks into place.

(Slight rotation of the bit may be necessary for proper alignment and full insertion.)

vi. Install feed system and rotate collar to lock position.

TOOL OPERATION

NOSEPIECE REPLACEMENT

1. Remove battery before changing the nosepiece.

2. Remove retention screw with ﬂat-tip screwdriver.

3. Set the nosepiece on the longest setting possible.

4. Depress the screw selector pin until it is completely depressed. It will be necessary to use a screw or

thin object to depress to this depth.

5. While holding the pin in this position, slide the nosepiece forward and off the slide body

6. Install the new nosepiece.

7. Replace the nosepiece retention screw ensuring it is seated snug against the slide body.

BELT HOOK ADJUSTMENT

To adjust the belt hook offset from the tool:

1. Remove the belt hook thumb screw until the locking plate can be removed.

2. Slide the belt hook out to the desired position, replace the locking plate, then re-install the thumb

screw.

To relocate the belt hook to opposite side of the tool:

1. Remove the thumb screw, locking plate, threaded plate and belt hook.

2. Insert the threaded plate on the opposite side of tool and re-install the hook at the desired position

using locking plate and thumb screw.

BATTERY PACK INSTALLATION

CAUTION

Only SENCO VB-Series 18V batteries should be used on SENCO tools:

VB-0155, 0160, 0161, 0162, 0190, 0191, 0194, 0195.

1. Align battery ribs with slots on the tool.

2. Push battery until it seats tightly on the tool.

3. A click can be heard when the release mechanism seats properly.

TOOL OPERATION

BATTERY PACK REMOVAL

1. Depress buttons on both sides of battery.

2. Slide battery off tool.

BATTERY CHARGING

1. Place battery pack in charger.

2. Align raised ribs on battery pack with groove in charger.

3. Press down on battery pack to be sure contacts on battery pack engage properly with contacts in

charger. When properly connected, the red light will turn on. Red ﬂashing light indicates fast

charging mode.

4. Red and green light ﬂashing indicates defective battery pack. Return battery pack to your nearest

SENCO Authorized Service Centre for inspection or replacement.

5. Solid red light indicates that the battery is charging.

6. When your battery pack becomes 80% charged, the red light will stay on and the green light will ﬂash.

When battery pack is fully charged, the red light will turn off and the green light will turn on.

7. After normal usage, 1 hour of charge time is required to be fully charged. A maximum charge time of

1 hour or less is required to recharge a completely discharged battery pack.

8. The battery pack will become slightly warm to the touch while charging. This is normal and does not

indicate a problem.

The battery pack houses 4 coloured LED lights. These LEDs indicate the state of charge and possible

problems inside the battery pack.

Standby/Power No Fade X X X X X

Standby Full Yes Fade Fade Ready for Use X X X

Charging Yes Solid Green Flashing Green <80% X X X

Fully Charged Yes Fading Green Fading Green 100% X X X

Evaluating Yes Solid Green X Measuring Flash Orange X X

*Temp Delay Yes Solid Green X Hot/Cold X Flash Orange X

Defective Yes Solid Green X Damaged X X Solid Red

Mode Power Charging/Full Condition Evaluate Temp. Delay Defective

Battery Pack

Inserted?

*Delay up to 20 minutes depending on battery cell temperature inside pack.

Figure 2 - Battery Charge Level Lights

Press raised red button on battery pack to check charge:

• Red Flashing = 0-15% Charge

• Red On = 16-25% Charge

• Red and Orange On = 26-50% Charge

• Red, Orange, and Green On = 51-75% Charge

• All On = 76-100% Charge

Tips for maintaining maximum battery life:

• Charge the battery pack before it is completely discharged.

• Always stop tool operation and charge the battery when you notice less tool power.

• Never recharge a fully charged battery.

• Overcharging shortens the battery service life.

Battery Disposal

• To preserve natural resources, please recycle or dispose of properly. This product contains

Li-Ion. Local state or federal laws may prohibit disposal of Li-Ion batteries in ordinary trash.

• Consult your local waste authority for information regarding available recycling and/or

disposal options.

• For more information on battery recycling call 1-800-8BATTERY.

Maintenance

Read section titled “Safety Warnings” before maintaining tool.

1. With battery removed, make daily inspection to ensure free movement of nosepiece and trigger.

Do not use tool if nosepiece or trigger sticks or binds.

2. Lubrication of the feed system is not necessary. DO NOT OIL.

3. Wipe tool clean daily and inspect for wear, especially the bit and nosepiece. Replace as necessary.

WARNING

Repairs other than those described here should be performed only by trained,

qualiﬁed personnel. Contact SENCO for information at 1-800-543-4596.

Accessories

SENCO offers a full line of DuraSpin screws and accessories for your SENCO tools, including:

• Bits

• Batteries

• Battery Chargers

• Storage Bag

• Assorted Nosepieces

• Safety Glasses

For more information or a fully illustrated catalogue of Senco accessories, contact your sales

representative or call Senco at 1-800-543-4596.

Technical Speciﬁcations

Table 4 - DS222-18V Tech Specs

VOLTAGE 18V

BATTERY AMPACITY 3000MAH

RPM 0-1600, 0-2500 REV/MIN

WEIGHT 5.47 LBS. (2.48KG) W/ BATTERY

HEIGHT 9.59" (243.5MM) MAX

LENGTH 14.66" (372.4MM) MAX

WIDTH 3.36" (85.4MM) MAX

RECHARGE TIME 1 HOUR

FASTENER CAPACITY 50 SCREWS (1 STRIP)

TORQUE DELIVERED 70 IN-LBS. MIN

GENERATED NOISE 84DB(A)

VIBRATION 2.5M/S2 MAX

FASTENER LENGTH 1-2"

FASTER RANGE #6-#12

Table 6 - DS322-18V Tech Specs

VOLTAGE 18V

BATTERY AMPACITY 3000MAH

RPM 0-1600, 0-2500 REV/MIN

WEIGHT 5.95 LBS. (2.70KG) MAX

HEIGHT 9.59” (243.5MM) MAX

LENGTH 16.52” (419.5MM) MAX

WIDTH 3.36” (85.4MM) MAX

RECHARGE TIME 1 HOUR

FASTENER CAPACITY 50 SCREWS (1 STRIP)

TORQUE DELIVERED 70 IN-LBS. MIN

GENERATED NOISE 84DB(A)

VIBRATION 2.5M/S2 MAX

FASTENER LENGTH 1-3”

FASTER RANGE #6-#12

Table 5 - DS225-18V Tech Specs

VOLTAGE 18V

BATTERY AMPACITY 3000MAH

RPM 0-5000 REV/MIN

WEIGHT 5.42 LBS. (2.46KG) MAX

HEIGHT 9.59” (243.5MM) MAX

LENGTH 14.66” (372.4MM) MAX

WIDTH 3.36” (85.4MM) MAX

RECHARGE TIME 1 HOUR

FASTENER CAPACITY 50 SCREWS (1 STRIP)

TORQUE DELIVERED 42 IN-LBS. MIN

GENERATED NOISE 84DB(A)

VIBRATION 2.5M/S2 MAX

FASTENER LENGTH 1-2”

FASTER RANGE #6-#12

Troubleshooting

Problem/Symptom Probable Cause Corrective Action

Tool will not start or run slowly Battery is discharged or defective Replace with charged battery pack

Trigger switch is defective Replace or return to Senco autho-

rized service centre for repair

Motor is defective

Tool will not fully drive fastener Bit is worn or incorrect bit installed Replace bit

Power capabilities of the tool have

been exceeded

Discontinue use for that applica-

tion

Tool is in reverse Switch tool to forward

Depth of drive not set properly See p. #10

Tool does not advance fastener Screw length/nosepiece position is

improperly set

See p. #9

Return spring is weak or broken Replace or return to authorized

service centre for repair

Defective collation material Use Senco branded fasteners for

optimum performance

Defective slide body Replace or return to authorized

service centre for repair

Screw strip is jammed in guide

track

Ensure strip slides freely in guide

track

Screws “kick out” or misdrive

during use

Screw length/nosepiece position is

improperly set

See p. #9

Incorrect bit installed Ensure correct bit type and length

are installed

Defective or damaged feed system Return to Senco or Authorized

service centre for repair

Bit will not install Bit not properly inserted into drive

shaft

See p. #11

Clutch teeth not aligned Pulse trigger while holding back

release button

Not a Senco bit Use only the appropriate Senco bit

Bit will not release Not a Senco bit Use only the appropriate Senco bit

Clutch teeth not aligned Pulse trigger while holding back

release button

Bit slips off screw or screw is

driven at an angle

Tool slid forward during drive Hold tool ﬁrmly while driving

Bit is worn or broken Replace bit

Nosepiece is worn or damaged Replace or return to Senco autho-

rized service centre for repair

Bit is worn or broken Replace bit

Fastener Jams Screw length/nosepiece position is

improperly set

See p. #9

Defective collation material Use Senco branded fasteners for

optimum performance

Nosepiece damaged or bent Replace or return to authorized

service centre for repair

Screw partially driven into collation

material then feed system released

Remove jammed screw with

ﬁngers or pliers and resume use

Feed system “sticks” or returns

slowly

Debris build-up on mechanism Clean mechanism

Return spring is weak or broken Replace or return to authorized

service centre for repair

Bit sticking in collation material Use Senco branded fasteners for

optimum performance

Always attempt to store screws

in cool dry place before use.

Overheated collation can get soft

and cause a delay in feed system

return

Tool overheats Drive application requires too

much torque

Discontinue use for that applica-

tion

Pushing force becomes excessive Improper screw for application Consider alternative fastener

CAM screw is loose or damaged Tighten or replace CAM screw

Debris build-up on mechanism Clean mechanism

Battery will not charge Defective battery See p. #12 for battery error code

description

Tool front-end will not install onto

console

The collar is not turned to the full

unlock position

Rotate the collar to full unlock

position

Foreign object stuck inside the

connection

Be sure that no objects or parts

are jammed inside the connection

Components in connector may be

damaged

Replace front-end assembly or

return to Senco Authorized service

centre for repair

Tool front-end will not separate

from console

The collar is not turned to the full

unlock position

Rotate the collar to full unlock

position

Components in the connector may

be damaged

Return to Senco Authorized

service centre for repair

Limited Warranty

SENCO

Pneumatic, DuraSpin

, Cordless Tools

& Compressors

KYOCERA-SENCO Industrial Tools, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship.

SENCO warrants to the original retail purchaser that the following products will be free from defects in material or workmanship for the warranty period

Products New Reconditioned Products New Reconditioned

Pneumatic Tools

Five Years One Year Air Compressors One Year 90 Days

Fusion Tools Two Years Six Months Combo Kit Tools One Year 90 Days

Gas Tools Two Years Six Months Multi-Blow Hand Nailers One Year 90 Days

Duraspin Tools One Year 90 Days Stapling Hammers One Year 90 Days

= Both XP and Pro Series

During the warranty period (which begins on the purchase date), SENCO will repair or replace, at SENCO’s option and expense, any product or part

that is defective in materials or workmanship after examination by a SENCO Authorized Warranty Service Centre, subject to the exceptions, exclusions

and limitations described below. Any replacement product or part will carry a warranty for the balance of the warranty period applicable to the replaced

product or part. A DATED SALES RECEIPT OR PROOF OF PURCHASE FROM THE ORIGINAL RETAIL PURCHASER IS REQUIRED TO MAKE A

WARRANTY CLAIM. Warranty registration is also required and can be accomplished through on-line Product Registration at www.senco.com or by

completing and returning the postage paid warranty registration form included with your Operator’s manual/parts chart information, found inside the

product carton. To make a warranty claim, you must return the product, with proper receipt/proof of purchase and return transportation charges prepaid,

to a SENCO Authorized Warranty Service Centre. A list of SENCO Authorized Warranty Service Centres can be found at www.senco.com or by calling

1-800-543-4596 toll free. SENCO will perform its obligations under this warranty within a reasonable time after approval of the warranty claim.

SENCO Cordless:

1. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the SENCO Cordless tool will be free from defects

in materials and workmanship for two years after the purchase date.

2. SENCO warrants that the batteries and chargers used with SENCO Cordless tools will be free from defects in material and workmanship for

one year after the purchase date.

Warranty Exclusions

The following warranty exclusions apply:

seals, driver blades, piston stops, and piston/driver assembly.

2. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, accidents, operation beyond the recommended

speeds or voltage (electric units only), improper storage, or damage resulting from shipping.

3. Prod

4. Labour charges or loss or damage resulting from improper operation, maintenance or repairs are not covered by this warranty.

General Warranty Conditions

This warranty will be honoured only if:

A. Clean, dry, regulated compressed air has been used, at air pressure not exceeding the maximum indicated on the tool casting;

B. No e

C. No d

maintenance instructions).

THIS WARRANTY IS THE ONLY WARRANTY ON THE PRODUCT, AND SENCO DISCLAIMS ALL OTHER WARRANTIES. ANY IMPLIED WAR-

RANTIES WILL BE LIMITED IN DURATION TO THE APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE. SOME STATES DO NOT ALLOW

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. YOUR REMEDIES ARE

SOLELY AND EXCLUSIVELY AS STATED ABOVE. SENCO SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT,

OR SPECIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,

SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,

WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL SENCO’S LIABILITY EXCEED THE PRICE OF THE PRODUCT WHICH

HAS GIVEN RISE TO THE CLAIM OR LIABILITY. ANY LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE

EXPIRATION OF THE WARRANTY PERIOD SPECIFIED ABOVE. NO EMPLOYEE OR REPRESENTATIVE OF SENCO OR ANY DISTRIBUTOR OR

DEALER IS AUTHORIZED TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY.

Replacement of Tool Due to Natural Disaster

Such a claim will be honoured provided that the original retail purchaser had previously submitted a completed warranty registration card for the tool,

and then submits proof of ownership and an acceptable statement describing such Act of God documented by an insurance carrier, police department,

Customer Satisfaction

If for any reason the product does not perform to the original purchaser’s satisfaction, it can be returned to the place of purchase within thirty days with

dated sales receipt for a full refund of the purchase price (applies to new product sales only).

CINCINNATI, OHIO 45244-1611 USA

www.senco.com

160101

KYOCERA SENCO Industrial Tools

8450 Broadwell Road

Cincinnati, Ohio 45244

www.senco.com

DS222-18V

DS225-18V

DS322-18V

DESTORNILLADOR DE

ALIMENTACIÓN AUTOMÁTICA

Instrucciones para la operación

KYOCERA SENCO Industrial Tools

4270 Ivy Pointe Blvd.

Cincinnati, OH 45245

1-800-543-4596

www.senco.com

NFD810A10B10C • Publicado el 4 de noviembre de 2019

IMPORTANTE: Lea este documento antes de utilizar la herramienta.

Índice

Símbolos .................................................................................................................................. 3

Advertencias generales de seguridad con las herramientas eléctricas ................................ 4

Seguridad en el área de trabajo ............................................................................................. 4

Seguridad con la electricidad ................................................................................................ 4

Seguridad personal ............................................................................................................... 4

Uso y cuidado de las herramientas eléctricas ....................................................................... 5

Uso y cuidado de las herramientas de baterías ..................................................................... 5

Servicio ................................................................................................................................. 6

Advertencias de seguridad del destornillador ........................................................................ 6

Advertencias de seguridad en cuanto al cargador y la batería .............................................. 6

Descripción funcional .............................................................................................................. 8

Operación de la herramienta .................................................................................................. 9

Ajuste de la longitud del sujetador ........................................................................................ 9

Carga de la herramienta ........................................................................................................ 9

Ajuste de la velocidad a la que se introducen los tornillos .................................................. 10

Inserción de los tornillos ..................................................................................................... 10

Seguro del disparador ......................................................................................................... 10

Ajuste de la profundidad a la que se introducen los tornillos .............................................. 10

Operación inversa ............................................................................................................... 11

Reemplazo de la broca ........................................................................................................ 11

Reemplazo de la punta ........................................................................................................ 12

Ajuste del gancho de cinturón ............................................................................................. 12

Instalación del paquete de la batería ................................................................................... 12

Remoción del paquete de la batería .................................................................................... 13

Carga de la batería .............................................................................................................. 13

Eliminación de la batería ..................................................................................................... 14

Mantenimiento ...................................................................................................................... 14

Accesorios ............................................................................................................................. 14

Especiﬁcaciones técnicas ..................................................................................................... 15

Solución de problemas ......................................................................................................... 16

La page charge ...

Senco DS222-18V Le manuel du propriétaire

Marque: Senco

Modèle: DS222-18V

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

español: Senco DS222-18V El manual del propietario

Senco DS222-18V Le manuel du propriétaire

Ce manuel convient également à

Senco DS222-18V Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents