Frigidaire FFET1222QB Guide d'installation
- Taper
- Guide d'installation
4
Í
NOTE
The exterior walls of the refrigerator may become quite
warm as the compressor works to transfer heat from
the inside. Temperatures as much as 30° F warmer than
room temperature can be expected. For this reason it is
particularly important in hotter climates to allow enough
space for air circulation around your refrigerator.
/HYHOLQJ
The refrigerator must have all bottom corners resting
¿UPO\RQVROLGÀRRU7KHÀRRUPXVWEHVWURQJHQRXJK
to support a fully loaded refrigerator. NOTE: It is very
important for your refrigerator to be level in order to
function properly. If the refrigerator is not leveled during
installation, the door may be misaligned and not close or
seal properly, causing cooling, frost, or moisture problems.
7R/HYHO<RXU5HIULJHUDWRU
After removing all interior and exterior packing materials,
crating screws and wood base, use a carpenter’s level
to level the refrigerator from front-to-back. Adjust the
plastic leveling feet in front, ½ bubble higher, so that the
door closes easily when left halfway open.
Í
NOTE
The direction in which your refrigerator doors open
(door swing) can be reversed, from left to right or right
to left, by moving the door hinges from one side to the
other. Reversing the door swing should be performed
E\DTXDOL¿HGSHUVRQ
INSTALLATION
This Use & Care Guide provides general operating
instructions for your model. Use the refrigerator only as
instructed in this Use & Care Guide. %HIRUHVWDUWLQJWKH
UHIULJHUDWRUIROORZWKHVHLPSRUWDQW¿UVWVWHSV
/RFDWLRQ
Choose a place that is near a grounded electrical outlet.
Do Not use an extension cord or an adapter plug.
)RUWKHPRVWHI¿FLHQWRSHUDWLRQWKHUHIULJHUDWRU
should be located where surrounding temperatures
will not drop below 10° F (-12° C) or exceed 110° F
(43° C). The Freeze Control Feature is designed
to automatically maintain the selected interior
refrigerator temperature within these boundaries.
Allow space around the unit for good air circulation.
Leave a 2 inch (50 mm) space on the back, 1 inch
(20 mm) on the sides, and 12 inches (300 mm)
above the refrigerator for adequate circulation.
Door Parts
Top Hinge
Top Hinge Shim
Center Hinge
Center Hinge Shim
Bottom Right Hinge
Right Pin Assembly (2)
Parts included with Hinge Kit (packed inside unit)
Bottom Left Hinge
Left Pin Assembly (2)
Hole Plug (3)
IMPORTANT
Before you begin, unplug the electrical power cord from
the wall outlet. Remove any food from door shelves.
'2255(9(56$/,16758&7,216
<RXVKRXOG¿QGDKLQJHNLWSDFNHGLQVLGH\RXUXQLWZLWKWKH
following parts that will be needed to reverse the doors:
5
'2255(9(56$/,16758&7,216
Remove
1
1
Top Cap
Top Hinge Top Hinge
Shim
Hinge Cover
Pull Up
Dismantle
Pull
Up
Center
Hinge
Center
Hinge Shim
6WHS
Remove top hinge cover. Unscrew and remove the top
hinge and top hinge shim. Keep the screws so they can
be used on the opposite side.
6WHS
Lift the freezer door up and away from the appliance.
6WHS
Unscrew and remove the middle hinge and middle hinge
shim. Save the screws. Lift the refrigerator door up and
away from the appliance.
Remove
Right Hand
Hinge
New Bottom
Left Hand
Hinge
6WHS
Unscrew and remove the bottom right hinge. Save the
screws. Remove screw covers from opposite corner (left)
and cover exposed holes (right). Attach new bottom left
hinge with the screws removed from the opposite side.
6
1
Hinge Cover
Top Hinge
Top Hinge
Shim
Top Cap
Insert
Middle
Hinge
Replace
Door
Center
Hinge
Center
Hinge
Shim
6WHS
Place the refrigerator door on the bottom left hinge.
Ensure the door is aligned horizontally and vertically.
Attach middle hinge to top (left) of refrigerator door,
attach shim to the back of hinge, align with holes and
DI¿[WRPLGGOHEHDPZLWKUHVHUYHGVFUHZV)DVWHQZLWK
screwdriver (not included).
6WHS
Place the freezer door on the middle hinge. Ensure that
the door is aligned horizontally and vertically, and that the
gasket seals on all sides before attaching the top hinge.
Attach the top hinge and shim and replace the hinge cover
and top cap.
2
2
2
3
3
3
Freezer
Door
Refrigerator
Door
6WHS
Remove right pin assemblies from the bottom of the
freezer and refrigerator doors. On the opposite side,
attach the replacement pin assemblies (located in
the plastic bag with the Use and Care Manual) with a
screwdriver. Note: You must re-use the screws from
the pin assemblies that are removed in this step when
attaching the new assemblies.
'2255(9(56$/,16758&7,216
-
1
-
2
-
3
