Simplicity 150000 Manuel utilisateur
- Catégorie
- Accessoires pour véhicules automobiles
- Taper
- Manuel utilisateur
Not for
Reproduction
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
80088589
Revision: A
Not for
Reproduction
3
9
10
11
12
13
14
15
16
17
18
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA. All rights reserved.
This manual contains safety information to make you aware of the hazards and risks
associated with engines and how to avoid them. It also contains instructions for the
proper use and care of the engine. Because Briggs & Stratton Corporation does not
necessarily know what equipment this engine will power, it is important that you read
and understand these instructions and the instructions for the equipment.Save these
original instructions for future reference.
Note:The figures and illustrations in this manual are provided for reference only and
may differ from your specific model. Contact your dealer if you have questions.
For replacement parts or technical assistance, record below the engine model, type,
and code numbers along with the date of purchase. These numbers are located on your
engine (see theFeatures and Controlssection).
Date of Purchase
Engine Model - Type - Trim
Engine Serial Number
Recycling Information
Recycle all packaging, used oil, and batteries according to
applicable government regulations.
Operator Safety
Safety Alert Symbol and Signal Words
The safety alert symbol ( ) is used to identify safety information about hazards that
can result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used
with the alert symbol to indicate the likelihood and the potential severity of injury. In
addition, a hazard symbol may be used to represent the type of hazard.
DANGERindicates a hazard which, if not avoided,will result in death or
serious injury.
WARNINGindicates a hazard which, if not avoided,could result in death or
serious injury.
CAUTIONindicates a hazard which, if not avoided,could result in minor or
moderate injury.
NOTICEindicates a situation thatcould result in damage to the product.
Hazard Symbols and Meanings
Safety information about
hazards that can result in
personal injury.
Read and understand the
Operator's Manual before
operating or servicing the
unit.
Fire hazard Explosion hazard
Shock hazard Toxic fume hazard
Hot surface hazard Noise hazard - Ear protection
recommended for extended
use.
Thrown object hazard -
Wear eye protection.
Explosion hazard
Frostbite hazard Kickback hazard
Amputation hazard -
moving parts
Chemical hazard
Thermal heat hazard Corrosive
Safety Messages
WARNING
This product can expose you to chemicals including gasoline engine exhaust, which
is known to the State of California to cause cancer, and carbon monoxide, which is
known to the State of California to cause birth defects or other reproductive harm. For
more information go to www.P65Warnings.ca.gov.
WARNING
Briggs & Stratton® Engines are not designed for and are not to be used to power:
fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);
motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not
sanctioned by Briggs & Stratton. For information about competitive racing products,
see www.briggsracing.com. For use with utility and side-by-side ATVs, please contact
Briggs & Stratton Power Application Center, 1-866-927-3349. Improper engine
application may result in serious injury or death.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Adding Fuel
• Turn engine off and let engine cool at least 2 minutes before removing the fuel
cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the
bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
• If fuel spills, wait until it evaporates before starting engine.
When Starting Engine
• Make sure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in
place and secured.
• Do not crank engine with spark plug removed.
• If engine floods, set choke (if equipped) to OPEN / RUN position, move throttle (if
equipped) to FAST position and crank until engine starts.
When Operating Equipment
• Do not tip engine or equipment at angle which causes fuel to spill.
• Do not choke the carburetor to stop engine.
• Never start or run the engine with the air cleaner assembly (if equipped) or the air
filter (if equipped) removed.
When Changing Oil
• If you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel can
leak out and result in a fire or explosion.
When Tipping Unit for Maintenance
• When performing maintenance that requires the unit to be tipped, the fuel tank, if
mounted on the engine, must be empty or fuel can leak out and result in a fire or
explosion.
When Transporting Equipment
• Transport with fuel tank EMPTY or with fuel shut-off valve in the CLOSED
position.
When Storing Fuel Or Equipment With Fuel In Tank
Not for
Reproduction
5
• Store away from furnaces, stoves, water heaters or other appliances that have
pilot lights or other ignition sources because they can ignite fuel vapors.
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
• If there is natural or LP gas leakage in area, do not start engine.
• Do not use pressurized starting fluids because vapors are flammable.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or
taste it. Even if you do not smell exhaust fumes, you could still be exposed
to carbon monoxide gas. If you start to feel sick, dizzy, or weak while using
this product, get to fresh air RIGHT AWAY. See a doctor. You may have carbon
monoxide poisoning.
• Operate this product ONLY outside far away from windows, doors and vents to
reduce the risk of carbon monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up according to the manufacturer's instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages, basements, crawlspaces,
sheds, or other partially-enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly build up in these spaces
and can linger for hours, even after this product has shut off.
• ALWAYS place this product downwind and point the engine exhaust away from
occupied spaces.
WARNING
Rapid retraction of starter cord (kickback) will pull hand and arm toward engine
faster than you can let go.
Broken bones, fractures, bruises or sprains could result.
• When starting engine, pull the starter cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
• Remove all external equipment / engine loads before starting engine.
• Direct-coupled equipment components such as, but not limited to, blades,
impellers, pulleys, sprockets, etc., must be securely attached.
WARNING
Rotating parts can contact or entangle hands, feet, hair, clothing, or
accessories.
Traumatic amputation or severe laceration can result.
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
• Do not wear loose-fitting clothing, dangling drawstrings or items that could become
caught.
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
• It is a violation of California Public Resource Code, Section 4442, to use or
operate the engine on any forest-covered, brush-covered, or grass-covered land
unless the exhaust system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or federal jurisdictions
may have similar laws. Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust system installed on this
engine.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation, or
laceration.
Fire hazard
Before performing adjustments or repairs:
• Disconnect the spark plug wire and keep it away from the spark plug.
• Disconnect battery at negative terminal (only engines with electric start.)
• Use only correct tools.
• Do not tamper with governor spring, links or other parts to increase engine speed.
• Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit,
and may result in injury.
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
When testing for spark:
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
Features and Controls
Engine Controls
Compare the illustration (Figure: 1, 2, 3, 4) with your engine to familiarize yourself with
the location of various features and controls.
A. Engine Identification Numbers Model - Type - Code
B. Engine Serial Number
C. Fuel Tank and Cap
D. Air Cleaner
E. Starter Cord Handle (if equipped)
F. Dipstick
G. Oil Drain Plug
H. Muffler, Muffler Guard (if equipped), Spark Arrester (if equipped)
I. Choke (if equipped)
J. Throttle Control (if equipped)
K. Fuel Shut-off (if equipped)
L. Fuel Filter (if equipped)
M. Air Intake Grille
N. Oil Filter (if equipped)
O. Electric Starter (if equipped)
P. Stop Switch (if equipped)
Q. Spark Plug
Engine Control Symbols and Meanings
Engine speed - FAST Engine speed - SLOW
Engine speed - STOP ON - OFF
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
Engine start - Choke
CLOSED
Engine start - Choke OPEN
Fuel Cap
Fuel Shut-off - OPEN
Fuel Shut-off - CLOSED
Fuel level - Maximum
Do not overfill
Operation
Oil Recommendations
Oil Capacity:See theSpecificationssection.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers may have added oil to the engine. Before you start the engine for the first
time, make sure to check the oil level and add oil as specified by the instructions in
this manual. If you start the engine without oil, it will be damaged beyond repair and
will not be covered under warranty.
We recommend the use of Briggs & Stratton
®
Warranty Certified oils for best
performance. Other high-quality detergent oils are permitted if classified for service SF,
SG, SH, SJ or higher. Do not use special additives.
Outdoor temperatures determine the correct oil viscosity for the engine. Use the chart
to select the best viscosity for the outdoor temperature range expected. Engines on
most outdoor power equipment operate well with 5W-30 Synthetic oil. For equipment
operated in hot temperatures, Vanguard
®
15W-50 Synthetic oil gives the best
protection.
A SAE 30 -Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.
B 10W-30 -Above 80 °F (27 °C) the use of 10W-30 may cause increased oil
consumption. Checkthe oil level frequently.
C 5W-30
D Synthetic 5W-30
E
Vanguard
®
Synthetic 15W-50
Check and Add Oil
See Figure: 5
Before checking or adding oil
• Make sure the engine is level.
• Clean the oil fill area of any debris.
• See the Specifications section for oil capacity.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers may have added oil to the engine. Before you start the engine for the first
time, make sure to check the oil level and add oil according to the instructions in this
manual. If you start the engine without oil, it will be damaged beyond repair and will
not be covered under warranty.
Check Oil Level
1. Remove the dipstick (A, Figure 5) and wipe with a clean cloth.
2. Install and tighten the dipstick (A, Figure 5).
3. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 5) on the dipstick.
Add Oil
1. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 5). Do not
overfill. After adding oil, wait one minute and then check the oil level.
2. Reinstall and tighten the dipstick (A, Figure 5).
Low Oil Protection System (if equipped)
Some engines are equipped with a low oil sensor. If the oil is low, the sensor will either
activate a warning light or stop the engine. Stop the engine and follow these steps
before restarting the engine.
• Make sure the engine is level.
• Check the oil level. See the Check Oil Level section.
• If the oil level is low, add the proper amount of oil. Start the engine and make sure
the warning light (if equipped) is not activated.
• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton
Authorized Service Dealer to have the oil problem corrected.
Fuel Recommendations
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE Do not use unapproved gasolines, such as E15 and E85. Do not mix oil in
gasoline or modify the engine to run on alternate fuels. Use of unapproved fuels will
damage the engine components, which will not be covered under warranty.
To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel.
SeeStorage.All fuel is not the same. If start or performance problems occur, change
fuel providers or brands. This engine is certified to operate on gasoline. The emissions
control system for carbureted engines is EM (Engine Modifications). The emissions
control systems for engines with electronic fuel injection are ECM (Engine Control
Module), MPI (Multi Port Injection), and if equipped an O2S (Oxygen Sensor).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)
gasoline is acceptable.
For carbureted engines, high altitude adjustment is required to maintain performance.
Operation without this adjustment will cause decreased performance, increased fuel
consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service
Dealer for high altitude adjustment information. Operation of the engine at altitudes
below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.
Add Fuel
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When adding fuel
• Turn engine off and let engine cool at least 2 minutes before removing the fuel
cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the
bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
• If fuel spills, wait until it evaporates before starting engine.
1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.
2. Fill the fuel tank (A, Figure6) with fuel. To allow for expansion of the fuel, do not
fill above the bottom of the fuel tank neck (B).
Not for
Reproduction
7
3. Install the fuel cap.
Start and Stop Engine
See Figure: 7, 8, 9
Start Engine
WARNING
Rapid retraction of starter cord (kickback) will pull hand and arm toward engine
faster than you can let go.
Broken bones, fractures, bruises or sprains could result.
• When starting engine, pull the starter cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Starting Engine
• Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in place
and secured.
• Do not crank engine with spark plug removed.
• If engine floods, set choke (if equipped) to OPEN / RUN position, move throttle (if
equipped) to FAST position and crank until engine starts.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or
taste it. Even if you do not smell exhaust fumes, you could still be exposed to
carbon monoxide gas. If you start to feel sick, dizzy, or weak while using this
product, shut it off and get to fresh air RIGHT AWAY. See a doctor. You may
have carbon monoxide poisoning.
• Operate this product ONLY outside far away from windows, doors and vents to
reduce the risk of carbon monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up according to the manufacturer's instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages, basements, crawlspaces,
sheds, or other partially-enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly build up in these spaces
and can linger for hours, even after this product has shut off.
• ALWAYS place this product downwind and point the engine exhaust away from
occupied spaces.
NOTICE This engine was shipped from Briggs & Stratton without oil. Before you
start the engine, make sure you add oil according to the instructions in this manual.
If you start the engine without oil, it will be damaged beyond repair and will not be
covered under warranty.
Determine The Starting System
Before starting the engine, you must determine the type of starting system that is on
your engine. Your engine will have one of the following types.
•
ReadyStart
®
System: This features a temperature controlled automatic choke. It
does not have a manual choke or a primer.
• Choke System: This features a choke to be used for starting in cool
temperatures. Some models will have a separate choke control while others will
have a combination choke/throttle control. This type does not have a primer.
To start your engine, follow the instructions for your type of starting system.
Note:Equipment may have remote controls. See the equipment manual for location and
operation of remote controls.
ReadyStart
®
System
1. Check the engine oil. See the Check Oil Level section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.
4. Move the throttle control (B, Figure 7, 8), if equipped, to the FAST position.
Operate the engine in the FAST position.
5. Push the stop switch (D, Figure 7, 8), if equipped, to the ON position.
6. If the product is equipped with an engine stop lever (C, Figure 9), hold the engine
stop lever against the handle.
7. Rewind Start, if equipped: Firmly hold the starter cord handle (E, Figure 7, 8).
Pull the starter cord handle slowly until resistance is felt, then pull rapidly.
WARNING
Rapid retraction of the starter cord (kickback) will pull your hand and arm toward the
engine faster than you can let go. Broken bones, fractures, bruises or sprains could
result. When starting engine, pull the starter cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
8. Electric Start, if equipped: Turn the electric start switch to the ON / START
position.
NOTICE To extend the life of the starter, use short starting cycles (five seconds
maximum). Wait one minute between starting cycles.
Note:If the engine does not start after repeated attempts, contact your local dealer or go
to BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).
Choke System
1. Check the engine oil. See the Check Oil Level section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.
4. Move the throttle control (B, Figure 7, 8), if equipped, to the FAST position.
Operate the engine in the FAST position.
5. Move the choke control (F, Figure 7), to the CLOSED position.
Note:Choke is usually unnecessary when restarting a warm engine.
6. If the product is equipped with an engine stop lever (C, Figure 9), hold the engine
stop lever against the handle.
7. Rewind Start, if equipped: Firmly hold the starter cord handle (E, Figure 7, 8).
Pull the starter cord handle slowly until resistance is felt, then pull rapidly.
WARNING
Rapid retraction of the starter cord (kickback) will pull your hand and arm toward the
engine faster than you can let go. Broken bones, fractures, bruises or sprains could
result. When starting engine, pull the starter cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
8. Electric Start, if equipped: Turn the electric start switch to the ON / START
position.
NOTICE To extend the life of the starter, use short starting cycles (five seconds
maximum). Wait one minute between starting cycles.
9. As the engine warms up, move the choke control (F, Figure 7) to the OPEN / RUN
position.
Note:If the engine does not start after repeated attempts, contact you local dealer or go
to BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).
Stop Engine
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
• Do not choke the carburetor to stop the engine.
1. Engine Stop Lever, if equipped: Release the engine stop lever (E, Figure 9).
Stop Switch, if equipped: Move the stop switch (D, Figure 7, 8) to the OFF
position.
Throttle Control, if equipped: Move the throttle control (B, Figure 7, 8) to the
STOP position.
Electric Start Key, if equipped: Turn the electric start key to the OFF / STOP
position. Remove the key and keep in a safe place out of the reach of children.
2. After the engine stops, move the fuel shut-off (A, Figure 7), if equipped, to the
CLOSED position.
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
Maintenance
NOTICE If the engine is tipped during maintenance, the fuel tank, if mounted on
engine, must be empty and the spark plug side must be up. If the fuel tank is not
empty and if the engine is tipped in any other direction, it may be difficult to start due
to oil or gasoline contaminating the air filter and/or the spark plug.
WARNING
When performing maintenance that requires the unit to be tipped, the fuel tank, if
mounted on the engine, must be empty or fuel can leak out and result in a fire or
explosion.
We recommend that you see any Briggs & Stratton Authorized Service Dealer for all
maintenance and service of the engine and engine parts.
NOTICE All the components used to build this engine must remain in place for
proper operation.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation, or
laceration.
Fire hazard
Before performing adjustments or repairs:
• Disconnect the spark plug wire and keep it away from the spark plug.
• Disconnect battery at negative terminal (only engines with electric start).
• Use only correct tools.
• Do not tamper with governor spring, links or other parts to increase engine speed.
• Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit,
and may result in injury.
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
When testing for spark:
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
Emissions Control Service
Maintenance, replacement, or repair of the emissions control devices and
systems may be performed by any off-road engine repair establishment or
individual. However, to obtain "no charge" emissions control service, the work must be
performed by a factory authorized dealer. See the Emissions Control Statements.
Maintenance Schedule
First 5 Hours
• Change oil
Every 8 Hours or Daily
• Check engine oil level
• Clean area around muffler and controls
• Clean air intake grille
Every 50 Hours or Annually
•
Clean air filter
1
•
Clean pre-cleaner (if equipped)
1
• Change engine oil
• Replace oil filter (if equipped)
• Service exhaust system
Every 200 Hours
•
Replace air filter
1
•
Replace pre-cleaner (if equipped)
1
Annually
• Replace spark plugs
• Service fuel system
•
Service cooling system
1
•
Check valve clearance
2
1
In dusty conditions or when airborne debris is present, clean more often.
2
Not required unless engine performance problems are noted.
Carburetor and Engine Speed
Never make adjustments to the carburetor or engine speed. The carburetor was set at
the factory to operate efficiently under most conditions. Do not tamper with the governor
spring, linkages, or other parts to change the engine speed. If any adjustments are
required contact a Briggs & Stratton Authorized Service Dealer for service.
NOTICE The equipment manufacturer specifies the maximum speed for the engine
as installed on the equipment.Do not exceedthis speed. If you are not sure what the
equipment maximum speed is, or what the engine speed is set to from the factory,
contact a Briggs & Stratton Authorized Service Dealer for assistance. For safe and
proper operation of the equipment, the engine speed should be adjusted only by a
qualified service technician.
Service Spark Plug
See Figure:10
Check the gap (A, Figure10) with a wire gauge (B). If necessary, reset the gap. Install
and tighten the spark plug to the recommended torque. For gap setting or torque, see
theSpecificationssection.
Note:In some areas, local law requires using a resistor spark plug to suppress ignition
signals. If this engine was originally equipped with a resistor spark plug, use the same
type for replacement.
Service Exhaust System
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
• It is a violation of California Public Resource Code, Section 4442, to use or
operate the engine on any forest-covered, brush-covered, or grass-covered land
unless the exhaust system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or federal jurisdictions
may have similar laws. Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust system installed on this
engine.
Remove accumulated debris from muffler and cylinder area. Inspect the muffler for
cracks, corrosion, or other damage. Remove the deflector or the spark arrester, if
equipped, and inspect for damage or carbon blockage. If damage is found, install
replacement parts before operating.
WARNING
Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit, and
may result in injury.
Change Engine Oil
See Figure: 11, 12, 13, 14
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
• When you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel
can leak out and result in a fire or explosion.
Not for
Reproduction
9
• Allow muffler, engine cylinder and fins to cool before touching.
Used oil is a hazardous waste product and must be disposed of properly. Do not discard
with household waste. Check with your local authorities, service center, or dealer for
safe disposal/recycling facilities.
Remove Oil
1. With engine off but still warm, disconnect the spark plug wire(s) (D, Figure 11) and
keep it away from the spark plug(s) (E).
2. Remove the dipstick (A, Figure 12).
3. Remove the oil drain plug (F, Figure 13). Drain the oil into an approved container.
Note:Any of the oil drain plugs (G, Figure 13) may be installed in the engine.
4. After the oil has drained, install and tighten the oil drain plug (F, Figure 13).
5. When you drain the oil from the top oil fill tube (C, Figure 14), keep the spark plug
(E) end of the engine up. Drain the oil into an approved container.
WARNING
When you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel
can leak out and result in a fire or explosion. To empty the fuel tank, run the engine
until it stops from lack of fuel.
Change Oil Filter, if equipped
Some models are equipped with an oil filter. For replacement intervals, see the
Maintenance Schedule.
1. Drain the oil from the engine. See Remove Oil section.
2. Remove the oil filter (H, Figure 12) and dispose of properly.
3. Before you install the new oil filter, lightly lubricate the oil filter gasket with fresh,
clean oil.
4. Install the oil filter by hand until the gasket contacts the oil filter adapter, then
tighten the oil filter 1/2 to 3/4 turns.
5. Add oil. See Add Oil section.
6. Start and run the engine. As the engine warms up, check for oil leaks.
7. Stop the engine and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 12) on the dipstick.
Add Oil
• Make sure the engine is level.
• Clean the oil fill area of any debris.
• See the Specifications section for oil capacity.
1. Remove the dipstick (A, Figure 12) and wipe with a clean cloth.
2. Slowly pour oil into the engine oil fill (C, Figure 12). Do not overfill. After adding
oil, wait one minute and then check the oil level.
3. Install and tighten the dipstick (A, Figure 12).
4. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 12) on the dipstick.
5. Reinstall and tighten the dipstick (A, Figure 12).
6. Connect the spark plug wire(s) (D, Figure 11) to the spark plug(s) (E).
Service Air Filter
See Figure: 15, 16
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
• Never start and run the engine with the air cleaner assembly (if equipped) or the
air filter (if equipped) removed.
NOTICE Do not use pressurized air or solvents to clean the filter. Pressurized air
can damage the filter and solvents will dissolve the filter.
See the Maintenance Schedule for service requirements.
Various models use either a foam or a paper filter. Some models may also have an
optional pre-cleaner that can be washed and reused. Compare the illustrations in this
manual with the type installed on your engine and service as follows.
Foam Air Filter
1. Move the slide lock (A, Figure 15) to the unlock position and open the cover (B).
2. To prevent debris from falling into the carburetor, carefully remove the foam
element (C, Figure 15) from the air filter base.
3. Wash the foam element (C, Figure 15) in liquid detergent and water. Squeeze dry
the foam element in a clean cloth.
4. Saturate the foam element (C, Figure 15) with clean engine oil. To remove the
excess engine oil, squeeze the foam element in a clean cloth.
5. Install the foam element (C, Figure 15) onto the air filter base.
6. Close the cover (B, Figure 15) and move the slide lock (A) to the locked position.
Paper Air Filter
1. Loosen the fastener(s) (A, Figure 16).
2. Remove the cover (B, Figure 16).
3. To prevent debris from falling into the carburetor, carefully remove the pre-cleaner
(D, Figure 16) and the filter (C) from the air filter base.
4. Remove the pre-cleaner (D, Figure 16) from the filter (C).
5. To loosen debris, gently tap the filter (C, Figure 16) on a hard surface. If the filter is
excessively dirty, replace with a new filter.
6. Wash the pre-cleaner (D, Figure 16) in liquid detergent and water. Allow the pre-
cleaner to throughly air dry. Do not oil the pre-cleaner.
7. Assemble the dry pre-cleaner (D, Figure 16) to the filter (C).
8. Install the filter (C, Figure 16) and the pre-cleaner (D) onto the air filter base. Make
sure the filter fits securely on the air filter base.
9. Install the cover (B, Figure 16) and secure with the fastener(s) (A). Make sure the
fastener(s) is tight.
Service Fuel System
See Figure: 17
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
• Before cleaning or replacing the fuel filter, drain the fuel tank or close the fuel shut-
off valve.
• If fuel spills, wait until it evaporates before starting engine.
• Replacement parts must be the same and installed in the same position as the
original parts.
Fuel Filter, if equipped
1. Before cleaning or replacing the fuel filter (A, Figure 17), drain the fuel tank or
close the fuel shut-off valve. Otherwise, fuel can leak out and cause a fire or
explosion.
2. Use pliers to squeeze tabs (B, Figure 17) on the clamps (C), then slide the clamps
away from the fuel filter (A). Twist and pull the fuel lines (D) off of the fuel filter.
3. Check the fuel lines (D, Figure 17) for cracks or leaks. Replace if necessary.
4. Replace the fuel filter (A, Figure 17) with an original equipment replacement filter.
5. Secure the fuel lines (D, Figure 17) with clamps (C) as shown.
Service Cooling System
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc., can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
NOTICE Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
1. Use a brush or dry cloth to remove debris from the air intake grille.
2. Keep linkage, springs and controls clean.
3. Keep the area around and behind the muffler, if equipped, free of any combustible
debris.
4. Make sure the oil cooler fins, if equipped, are free of dirt and debris.
After a period of time, debris can accumulate in the cylinder cooling fins and cause the
engine to overheat. This debris cannot be removed without partial disassembly of the
engine. Have a Briggs & Stratton Authorized Service Dealer inspect and clean the air
cooling system as recommended in the Maintenance Schedule.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Fuel Or Equipment With Fuel In Tank
• Store away from furnaces, stoves, water heaters or other appliances that have
pilot lights or other ignition sources because they can ignite fuel vapors.
Fuel System
See Figure:18
Store the engine level (normal operating position). Fill fuel tank (A, Figure18) with fuel.
To allow for expansion of fuel, do not overfill above the fuel tank neck (B).
Fuel can become stale when kept in a storage container for more than 30 days. Each
time you fill the container with fuel, addSTA-BIL 360°
®
PROTECTION™to the fuel as
specified by the manufacturer’s instructions. This keeps fuel fresh and decreases fuel-
related problems or contamination in the fuel system.
It is not necessary to drain fuel from the engine whenSTA-BIL
360°
®
PROTECTION™is added as instructed. Before storage, turn the engine ON for 2
minutes to move the fuel and stabilizer through the fuel system.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained
into an approved container. Run the engine until it stops from lack of fuel. The use of a
fuel stabilizer in the storage container is recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil. See the Change Engine Oil
section.
Troubleshooting
For assistance, contact your local dealer or go to BRIGGSandSTRATTON.COM or call
1-800-233-3723 (in USA).
Specifications
Model:140000
Displacement 13.60ci (223cc)
Bore 2.913in (74mm)
Stroke 2.040in (51,82mm)
Oil Capacity 18 - 20oz (,54 - ,59L)
Spark Plug Gap .020in (,51mm)
Spark Plug Torque 180lb-in (20Nm)
Armature Air Gap .010 - .014in (,25 - ,36mm)
Intake Valve Clearance .004 - .008in (,10 - ,20mm)
Exhaust Valve Clearance .004 - .008in (,10 - ,20mm)
Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily
at an angle up to 15°. Refer to the equipment operator's manual for safe allowable
operating limits on slopes.
Service Parts - Model:140000
Service Part Part Number
Air Filter, Foam 797301
Air Filter, Paper 795066, 5419
Pre-cleaner, Air Filter 796254
Oil - SAE 30 100005
Oil Filter 795990
Fuel Filter 298090, 5018
Resistor Spark Plug 692051
Spark Plug Wrench 89838, 5023
Spark Tester 19368
We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
Power Ratings:The gross power rating for individual gasoline engine models is
labeled in accordance with SAE (Society of Automotive Engineers) code J1940 Small
Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995.
Torque values are derived at 2600 RPM for those engines with “rpm” called out on the
label and 3060 RPM for all others; horsepower values are derived at 3600 RPM. The
gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power
values are taken with exhaust and air cleaner installed whereas gross power values
are collected without these attachments. Actual gross engine power will be higher than
net engine power and is affected by, among other things, ambient operating conditions
and engine-to-engine variability. Given the wide array of products on which engines
are placed, the gasoline engine may not develop the rated gross power when used in a
given piece of power equipment. This difference is due to a variety of factors including,
but not limited to, the variety of engine components (air cleaner, exhaust, charging,
cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions
(temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing
and capacity limitations, Briggs & Stratton may substitute an engine of higher rated
power for this engine.
Warranty
Briggs & Stratton Engine Warranty
Effective January 2019
Limited Warranty
Briggs & Stratton warrants that, during the warranty period specified below, it will repair
or replace, free of charge, any part that is defective in material or workmanship or
both. Transportation charges on product submitted for repair or replacement under this
warranty must be borne by purchaser. This warranty is effective for and is subject to
the time periods and conditions stated below. For warranty service, find the nearest
Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.
The purchaser must contact the Authorized Service Dealer, and then make the product
available to the Authorized Service Dealer for inspection and testing.
There is no other express warranty. Implied warranties, including those of
merchantability and fitness for a particular purpose, are limited to the warranty
period listed below, or to the extent permitted by law.Liability for incidental or
consequential damages are excluded to the extent exclusion is permitted by law. Some
states or countries do not allow limitations on how long an implied warranty lasts,
and some states or countries do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state and country to country
4
.
Standard Warranty Terms
1, 2, 3
Vanguard®; Commercial Series
3
Consumer Use - 36 months
Commercial Use - 36 months
XR Series
Consumer Use - 24 months
Commercial Use - 24 months
All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve
Consumer Use - 24 months
Commercial Use - 12 months
All Other Engines
Consumer Use - 24 months
Commercial Use - 3 months
Not for
Reproduction
11
1
These are our standard warranty terms, but occasionally there may
be additional warranty coverage that was not determined at time of
publication. For a listing of current warranty terms for your engine, go to
BRIGGSandSTRATTON.com or contact your Briggs & Stratton Authorized Service
Dealer.
2
There is no warranty for engines on equipment used for prime power in place
of a utility; standby generators used for commercial purposes, utility vehicles
exceeding 25 MPH, or engines used in competitive racing or on commercial or
rental tracks.
3
Vanguard installed on standby generators: 24 months consumer use, no
warranty commercial use. Commercial Series with manufacturing date before July
2017: 24 months consumer use, 24 months commercial use.
4
In Australia - Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by
emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.
The warranty period begins on the original date of purchase by the first retail or
commercial consumer. "Consumer use" means personal residential household use by a
retail consumer. "Commercial use" means all other uses, including use for commercial,
income producing or rental purposes. Once an engine has experienced commercial
use, it shall thereafter be considered as a commercial use engine for purposes of this
warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial
purchase date at the time warranty service is requested, the manufacturing date
of the product will be used to determine the warranty period. Product registration
is not required to obtain warranty service on Briggs & Stratton products.
About Your Warranty
This limited warranty covers engine-related material and/or workmanship issues only,
and not replacement or refund of the equipment to which the engine may be mounted.
Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered
under this warranty. Similarly, warranty is not applicable if the engine has been altered
or modified or if the engine serial number has been defaced or removed. This warranty
does not cover engine damage or performance problems caused by:
1. The use of parts that are not original Briggs & Stratton parts;
2. Operating the engine with insufficient, contaminated, or an incorrect grade of
lubricating oil;
3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater
than 10%, or the use of alternative fuels such as liquefied petroleum or natural gas
on engines not originally designed/manufactured by Briggs & Stratton to operate
on such fuels;
4. Dirt which entered the engine because of improper air cleaner maintenance or re-
assembly;
5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly
installed blade adapters, impellers, or other crankshaft coupled devices, or
excessive v-belt tightness;
6. Associated parts or assemblies such as clutches, transmissions, equipment
controls, etc., which are not supplied by Briggs & Stratton;
7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or
clog the cooling fins or flywheel area, or by operating the engine without sufficient
ventilation;
8. Excessive vibration due to over-speeding, loose engine mounting, loose or
unbalanced cutter blades or impellers, or improper coupling of equipment
components to the crankshaft;
9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of
equipment, or improper engine installation.
Warranty service is available only through Briggs & Stratton Authorized Service
Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map
at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).
80004537 (Rev. F)
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control
Warranty - Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "F" Trim Designation (Model-Type-
Trim Representation xxxxxx xxxx Fx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust and evaporative emissions (“emissions”) control system
warranty on your 2019-2021 engine/equipment. In California, new equipment that
use small off-road engines must be designed, built, and equipped to meet the State’s
stringent anti-smog standards. B&S must warrant the emissions control system on
your engine/equipment for the periods of time listed below provided there has been no
abuse, neglect or improper maintenance of your small off-road engine or equipment
leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine/equipment at no cost
to you including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust and evaporative emissions control system on your engine/equipment is
warranted for two years. If any emissions-related part on your engine/equipment is
defective, the part will be repaired or replaced by B&S.
Owner’s Warranty Responsibilities:
• As the engine/equipment owner, you are responsible for the performance of the
required maintenance listed in your owner’s manual. B&S recommends that you
retain all receipts covering maintenance on your engine/equipment, but B&S
cannot deny warranty coverage solely for the lack of receipts or for your failure to
ensure the performance of all scheduled maintenance.
• As the engine/equipment owner, you should however be aware that B&S may
deny you warranty coverage if your engine/equipment or a part has failed due to
abuse, neglect, or improper maintenance or unapproved modifications.
• You are responsible for presenting your engine/equipment to a B&S distribution
center or service center as soon as the problem exists. The warranty repairs shall
be completed in a reasonable amount of time, not to exceed 30 days. If you have
a question regarding your warranty rights and responsibilities you should contact
B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the
emissions control systems parts) to the extent these parts were present on the
B&S engine and/or B&S supplied fuel system.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
• Fuel line (for liquid fuel and fuel vapors), fuel line fittings, clamps
• Fuel tank, cap and tether
• Carbon canister and mounting bracket
• Pressure relief valves
• Liquid/Vapor separator
b. Air Induction System
• Air cleaner
• Intake manifold
• Purge and vent line
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product
warranty statement, whichever is greater. B&S warrants to the original purchaser
and each subsequent purchaser that the engine is designed, built, and equipped
so as to conform with all applicable regulations adopted by the Air Resources
Board; that it is free from defects in material and workmanship that could cause
the failure of a warranted part; and that it is identical in all material respects to the
engine described in the manufacturer’s application for certification. The warranty
Not for
Reproduction
12 BRIGGSandSTRATTON.COM
period begins on the date the engine or equipment is delivered to an ultimate
purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the
warranty period stated above. If any such part fails during the period of
warranty coverage, the part will be repaired or replaced by B&S at no
charge to the owner. Any such part repaired or replaced under the warranty
will be warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the period
of time prior to the first scheduled replacement point for that part. If the
part fails prior to the first scheduled replacement, the part will be repaired
or replaced by B&S at no charge to the owner. Any such part repaired or
replaced under warranty will be warranted for the remainder of the period
prior to the first scheduled replacement point for the part.
• Add-on or modified parts that are not exempted by the Air Resources
Board may not be used. The use of any non-exempted add-on or modified
parts by the owner will be grounds for disallowing a warranty claim. The
manufacturer will not be liable to warrant failures of warranted parts caused
by the use of a non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
TheEmissions Durability Perioddescribes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, theEmissions Durability Periodof an engine with anintermediaterating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80084158_A
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control
Warranty - Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-
Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust emissions (“emissions”) control system warranty on
your 2019-2021 engine. In California, new small off-road engines and large spark
ignited engines less than or equal to 1.0 liter must be designed, built, and equipped
to meet the State’s stringent anti-smog standards. B&S must warrant the emissions
control system on your engine for the periods of time listed below provided there has
been no abuse, neglect or improper maintenance of your small off-road engine or
equipment leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years.
If any emissions-related part on your engine is defective, the part will be repaired or
replaced by B&S.
Owner’s Warranty Responsibilities:
• As the engine owner, you are responsible for the performance of the required
maintenance listed in your owner’s manual. B&S recommends that you retain
all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
• As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
• You are responsible for presenting your engine to a B&S distribution center
or service center as soon as the problem exists. The warranty repairs shall be
completed in a reasonable amount of time, not to exceed 30 days. If you have a
question regarding your warranty rights and responsibilities, you should contact
B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the
emissions control systems parts) to the extent these parts were present on the
B&S engine.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
b. Air Induction System
• Air cleaner
• Intake manifold
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
Not for
Reproduction
13
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product
warranty statement, whichever is greater. B&S warrants to the original purchaser
and each subsequent purchaser that the engine is designed, built, and equipped
so as to conform with all applicable regulations adopted by the Air Resources
Board; that it is free from defects in material and workmanship that could cause
the failure of a warranted part; and that it is identical in allmaterial respects to the
engine described in the manufacturer’s application for certification. The warranty
period begins on the date the engine or equipment is delivered to an ultimate
purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the
warranty period stated above. If any such part fails during the period of
warranty coverage, the part will be repaired or replaced by B&S at no
charge to the owner. Any such part repaired or replaced under the warranty
will be warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operators’s Manual supplied, is warranted for the
period of time prior to the first scheduled replacement point for that part.
If the part fails prior to the first scheduled replacement, the part will be
repaired or replaced by B&S at no charge to the owner. Any such part
repaired or replaced under warranty will be warranted for the remainder of
the period prior to the first scheduled replacement point for the part.
• Add-on or modified parts that are not exempted by the Air Resources
Board may not be used. The use of any non-exempted add-on or modified
parts by the owner will be grounds for disallowing a warranty claim. The
manufacturer will not be liable to warrant failures of warranted parts caused
by the use of a non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
TheEmissions Durability Perioddescribes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, theEmissions Durability Periodof an engine with anintermediaterating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80084161_A
Not for
Reproduction
14 BRIGGSandSTRATTON.COM
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, EE.UU. Todos los derechos
reservados.
Este manual contiene información de seguridad para que usted tome conciencia
de los peligros y riesgos asociados con los motores, y cómo evitarlos. También
contiene instrucciones para el uso y cuidado apropiados del motor. Ya que
Briggs&StrattonCorporation no conoce necesariamente el equipo donde se usará este
motor, es importante que usted lea y entienda estas instrucciones y las instrucciones
del equipo.Conserve estas instrucciones originales para futuras consultas.
Nota:Las figuras e ilustraciones de este manual solo se proporcionan como referencia
y pueden diferir de su modelo específico. Comuníquese con su distribuidor si tiene
preguntas.
Para conseguir repuestos o asistencia técnica, registre a continuación los números
de modelo, tipo y código de su motor junto con la fecha de compra. Estos números se
encuentran localizados en su motor (consulte la secciónCaracterísticas y controles).
Fecha de compra
Modelo del motor - Tipo - Reglaje
Número de Serie del motor
Información de reciclaje
Todos los envases, el aceite usado y las baterías
deben reciclarse de acuerdo con las regulaciones
gubernamentales aplicables.
Seguridad del operador
Símbolo de alerta de seguridad y
palabras de señalización
El símbolo de aviso de seguridad ( ) se usa para identificar información de seguridad
acerca de los riesgos que pueden producir lesiones corporales. Se señaliza con una
palabra (PELIGRO, ADVERTENCIA o PRECAUCIÓN) con el símbolo de aviso para
indicar la probabilidad de una lesión y su potencial gravedad. Además, se puede usar
un símbolo de peligro para representar el tipo de riesgo.
PELIGROindica un riesgo que, si no se evita,ocasionará la muerte o lesiones
graves.
ADVERTENCIAindica un riesgo que, si no se evita,podría ocasionar la muerte
o lesiones graves.
PRECAUCIÓNindica un riesgo que, si no se evita,podría ocasionar lesiones
leves o moderadas.
AVISO indica una situación que podría provocar daños al producto.
Símbolos de peligro y significados
Información de seguridad
sobre peligros que pueden
conllevar a lesiones
personales.
Lea y entienda el Manual del
Operario antes de operar y
realizar mantenimientos a la
unidad.
Peligro de incendio Peligro de explosión
Peligro de descarga
eléctrica
Peligro de vapores tóxicos
Peligro de superficie
caliente
Peligro de ruido: Protección
auditiva recomendada para
uso extendido.
Peligro de elemento
lanzado: utilizar protección
para los ojos.
Peligro de explosión
Peligro de congelación Peligro de retroceso
Peligro de amputación:
piezas móviles
Peligro químico
Peligro de calor térmico Corrosivo
Mensajes de seguridad
ADVERTENCIA
Este producto puede exponerlo a sustancias químicas, entre las que se incluyen
emisiones de escape de motor de gasolina, reconocidas por el Estado de California
como causantes de cáncer, y monóxido de carbono, reconocido por el Estado
de California como causante de defectos de nacimiento u otros problemas
reproductivos. Para obtener más información, visite www.P65Warnings.ca.gov.
ADVERTENCIA
Los motores Briggs & Stratton® no están diseñados para y no deben utilizarse
para impulsar "karts" recreativos o deportivos; vehículos recreativos para niños
o deportivos todo terreno; motos; aerodeslizadores; productos de aeronaves o
vehículos utilizados en eventos competitivos no sancionados por Briggs & Stratton.
Para obtener información sobre productos para carreras competitivas, vaya a
www.briggsracing.com. Para uso con vehículos utilitarios y side-by-side todo terreno,
contáctese con el Centro de Aplicación de Potencia de Motores Briggs & Stratton
al 1-866-927-3349. El uso del motor para aplicaciones inadecuadas puede generar
lesiones graves o la muerte.
ADVERTENCIA
El combustible y sus vapores son extremamente inflamables y explosivos.
El fuego o la explosión pueden causar quemaduras graves o la muerte.
Cuando agregue combustible
• Apague el motor y deje que se enfríe por lo menos 2 minutos antes de remover la
tapa del combustible.
• Llene el tanque de combustible en exteriores o en un área bien ventilada.
• No llene excesivamente el tanque de combustible. Para permitir la expansión del
combustible, no llene el tanque por arriba de la parte inferior del cuello.
• Mantenga el combustible alejado de chispas, llamas abiertas, testigos piloto,
fuentes de calor y otras fuentes de encendido.
• Compruebe con frecuencia si existen grietas o fugas en las mangueras de
combustible, el tanque, la tapa y los accesorios. Reemplace las piezas, si es
necesario.
• Si se derramó combustible, espere hasta que se haya evaporado antes arrancar
el motor.
Cuando encienda el motor
• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el filtro de aire
(si está equipado) estén colocados y fijos en su lugar.
• No haga girar el motor si retiró la bujía.
• Si el motor se ahoga, coloque el estrangulador (si está equipado) en la posición
de apertura/funcionamiento (OPEN/RUN), coloque el acelerador (si está
equipado) en la posición de velocidad (FAST) y arranque el motor hasta que se
encienda.
Cuando opere el equipo
• No incline el motor ni el equipo de forma que pueda derramarse el combustible.
• No estrangule el carburador para detener el motor.
• Nunca encienda o haga funcionar el motor sin el conjunto del purificador de aire
(si tiene) o el filtro de aire (si tiene).
Not for
Reproduction
15
Cuando cambie el aceite
• Si drena el aceite desde el tubo superior de llenado de aceite, el tanque de
combustible debe estar vacío o de lo contrario podría presentarse una fuga de
combustible que podría ocasionar un incendio o una explosión.
Cuando incline la unidad para trabajos de mantenimiento
• Al realizar trabajos de mantenimiento que requieran inclinar la unidad, el tanque
de combustible, si está montado en el motor, debe estar vacío o podría haber una
fuga de combustible y generar un incendio o una explosión.
Cuando transporte el equipo
• Transporte con el tanque de combustible VACÍO o con la válvula de cierre de
combustible en la posición CLOSED.
Cuando almacene el combustible o el equipo con combustible en el tanque
• Almacene lejos de hornos, estufas, calentadores de agua u otros aparatos
que utilicen testigos piloto u otras fuentes de encendido ya que estos pueden
encender los vapores combustibles.
ADVERTENCIA
Dar arranque al motor crea chispeo.
El chispeo puede encender los gases inflamables cercanos.
podría ocasionar una explosión o un incendio.
• Si hay una fuga de gas natural o gas propano LP en el área, no le de arranque al
motor.
• No use líquidos de arranque presurizados ya que los vapores son inflamables.
ADVERTENCIA
PELIGRO DE GAS TÓXICO. La descarga de escape del motor contiene
monóxido de carbono, un gas tóxico que puede matar en minutos. NO puede
verlo, es inodoro e insípido. Incluso si no huele los gases del escape, puede
estar expuesto al monóxido de carbono. Si comienza a sentirse mareado o
débil cuando utiliza el producto, tome aire fresco INMEDIATAMENTE . consulte
a un médico, Puede haberse intoxicado con monóxido de carbono.
• Opere este producto SOLAMENTE al aire libre, lejos de ventanas, puertas y
ventilaciones, para reducir el riesgo de que el monóxido de carbono se acumule y
pueda circular a espacios habitados.
• Instale alarmas de monóxido de carbono con baterías o enchufe (batería de
respaldo) siguiendo las instrucciones del fabricante. Las alarmas de humo no
pueden detectar el monóxido de carbono.
• NO opere este producto dentro de hogares, garajes, sótanos, espacios reducidos,
cobertizos u otros espacios parcialmente cerrados, incluso si usa ventiladores o
deja las puertas y ventanas abiertas. El monóxido de carbono se puede acumular
rápidamente en estos espacios y puede permanecer durante horas, incluso
después de que se apaga este producto.
• SIEMPRE coloque este producto en la dirección del viento y apunte el escape del
motor lejos de espacios habitados.
ADVERTENCIA
La retracción rápida de la cuerda del arranque (retroceso violento) le halará la
mano y el brazo hacia el motor antes de que pueda soltarla.
Esto podría ocasionar roturas de huesos, fracturas, moretones o torceduras.
• Cuando arranque el motor, tire lentamente de la cuerda hasta sentir una
resistencia y, a continuación, tire rápidamente de ella para evitar su retroceso.
• Remueva todas las cargas externas del equipo/motor antes de darle arranque al
motor.
• Los componentes del equipo de acoplamiento directo, como cuchillas, impulsores,
poleas, ruedas dentadas, entre otros, se deben colocar firmemente.
ADVERTENCIA
Las piezas giratorias pueden tener contacto o atrapar las manos, los pies, el
cabello, la ropa o los accesorios.
podría ocasionar una amputación traumática o una laceración grave.
• Opere el equipo con los protectores en su lugar.
• Mantenga las manos y los pies a distancia de las partes rotantes.
• Recoja el pelo largo y quítese cualquier joya.
• No use ropa floja, tiras que cuelguen o artículos que puedan ser agarrados.
ADVERTENCIA
El funcionamiento de los motores produce calor. Las piezas de los motores,
especialmente el silenciador, se calientan demasiado.
Pueden ocurrir graves quemaduras al tocarlas.
Los desechos combustibles, tal como hojas, grama, maleza, etc. pueden
prenderse fuego.
• Deje que el silenciador, el cilindro y las aletas del motor se enfríen antes de
tocarlos.
• Extraiga los desechos acumulados en el área del silenciador y en el área del
cilindro.
• Es una violación del Código de Recursos Públicos de California, Sección 4442,
utilizar u operar el motor en cualquier espacio con árboles, maleza o grama a
menos que el sistema de escape esté equipado con un extintor de chispas, como
lo define la Sección 4442, mantenido en correcto funcionamiento. Otros estados o
jurisdicciones federales pueden tener leyes similares. Póngase en contacto con el
vendedor, el distribuidor o el fabricante del equipo original para obtener un extintor
de chispas diseñado para el sistema de escape instalado en este motor.
ADVERTENCIA
Las chispas no intencionales pueden provocar un incendio o una descarga
eléctrica.
El arranque accidental puede provocar enredos, amputaciones traumáticas o
laceraciones.
Peligro de incendio
Antes de hacer ajustes o reparaciones:
• Desconecte el cable de la bujía y manténgalo lejos de la bujía.
• Desconecte la batería en la terminal negativa (únicamente motores con arranque
eléctrico).
• Use solamente las herramientas correctas.
• No manipule el resorte del regulador, las conexiones u otras piezas para
aumentar la velocidad del motor.
• Las piezas de repuesto deben ser del mismo diseño y deben ser instaladas en la
misma posición que las piezas originales. Otras piezas pueden no funcionar igual
de bien, pueden dañar la unidad, y pueden causar lesiones.
• No golpee la volante con un martillo ni con un objeto pesado ya que la volante
podría astillarse más adelante durante la operación.
Cuando haga las pruebas de chispa:
• Use un probador de bujías aprobado.
• No haga las pruebas de chispa sin la bujía en su lugar.
Características y Controles
Controles del motor
Compare la ilustración (Figura: 1, 2, 3, 4) con su motor para familiarizarse con la
ubicación de diversas características y controles.
A. Números de identificación del motor Modelo, Tipo, Código
B. Número de Serie del motor
C. Tanque y Tapa de Combustible
D. Filtro de Aire
E. Manija Cuerda Arranque (si está equipada)
F. Varilla Indicadora Nivel de Aceite
G. Tapón Drenaje Aceite
H. Silenciador, protector de silenciador (si lo tuviera), supresor de chispas (si lo
tuviera)
I. Estrangulador (si está equipado)
J. Control de aceleración (si lo tuviera)
K. Cierre de combustible (si está equipado)
L. Filtro de combustible (si está equipado)
M. Parrilla de la admisión de aire
N. Filtro de aceite (si está equipado)
O. Arrancador eléctrico (si está equipada)
Not for
Reproduction
16 BRIGGSandSTRATTON.COM
P. Suiche de parada (si está equipado)
Q. Bujía
Símbolos de control del motor y
significados
Velocidad del motor -
RÁPIDA
Velocidad del motor - LENTA
Velocidad del motor -
PARADA
ENCENDIDO/APAGADO
Arranque del motor -
Estrangulador CERRADO
Arranque del motor -
Estrangulador ABIERTO
Tapa del combustible
Apagado del combustible -
ABIERTO
Apagado del combustible -
CERRADO
Nivel de combustible -
Máximo
No lo llene en exceso
Operación
Recomendaciones sobre el aceite
Capacidad de aceite:vea la sección deEspecificaciones.
AVISO
Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o
distribuidores de equipos pueden haber añadido aceite al motor. Antes de arrancar
el motor por primera vez, asegúrese de comprobar el nivel de aceite y agregar aceite
según las instrucciones de este manual. Si arranca el motor sin aceite, sufrirá daños
irreparables que la garantía no cubrirá.
Recomendamos el uso de aceites Briggs&Stratton
®
con garantía certificada para un
mejor rendimiento. Otros aceites detergentes de alta calidad son aceptables si están
clasificados para servicio SF, SG, SH, SJ o superior. No use aditivos especiales.
Las temperaturas exteriores determinarán la viscosidad correcta del aceite para el
motor. Use la tabla para seleccionar la mejor viscosidad para el margen de temperatura
exterior que se espera. Los motores en la mayoría de equipos de energía al aire
libre funcionan bien con aceite sintético 5W-30. Para equipos que funcionan a altas
temperaturas, el aceite sintético Vanguard
®
15W-50 proporciona la mejor protección.
A SAE30:El uso de SAE30 a temperaturas inferiores a 40°F (4°C) provocará
dificultades de arranque.
B 10W-30:El uso de 10W-30 a temperaturas mayores a 80°F (27°C) puede
provocar un aumento en el consumo de aceite. Revise el nivel de aceite con
mayor frecuencia.
C 5W-30
D 5W-30 sintético
E
Aceite sintético Vanguard
®
15W-50
Cómo revisar o agregar aceite
Consulte la figura: 5
Antes de la comprobación o aprovisionamiento de aceite
• Asegúrese de que el motor esté nivelado.
• Limpie el área de llenado de aceite y retire la suciedad.
• Consulte la sección Especificaciones para ver la capacidad del aceite.
AVISO
Este motor fue enviado desde Briggs & Stratton sin aceite. Los fabricantes o
distribuidores de equipos pueden haber añadido aceite al motor. Antes de arrancar
el motor, asegúrese de agregar aceite según las instrucciones de este manual. Si
arranca el motor sin aceite, sufrirá daños irreparables que la garantía no cubrirá.
Comprobación del nivel de aceite
1. Retire la varilla indicadora de nivel de aceite (A, Figura 5) y limpie con un paño
limpio.
2. Instale y ajuste la varilla indicadora de nivel de aceite (A, Figura 5).
3. Retire la varilla y revise el nivel de aceite. El nivel de aceite debe estar en la parte
superior del indicador de lleno (B, Figura 5) de la varilla.
Agregue aceite
1. Si el nivel es bajo, agregue aceite lentamente en el llenado de aceite del motor
(C, Figura 5). No llene en exceso. Después de añadir aceite, espere un minuto y
compruebe el nivel de aceite.
2. Vuelva a colocar la varilla y ajústela (A, Figura 5).
Sistema de protección contra bajo nivel
de aceite (si está equipado)
Algunos motores vienen equipados con un sensor de bajo nivel de aceite. Si el nivel de
aceite está bajo, el sensor activará una luz de advertencia o detendrá el motor. Pare el
motor y siga estos pasos antes de volver a arrancarlo.
• Asegúrese de que el motor esté nivelado.
• Controle el nivel de aceite. Consulte la sección Comprobación del nivel de
aceite .
• Si el nivel de aceite está bajo, agregue la cantidad adecuada de aceite. Arranque
el motor y asegúrese de que la luz de advertencia (si tiene) no esté activada.
• Si el nivel de aceite no está bajo, no arranque el motor. Para hacer corregir
el problema del aceite, póngase en contacto con un distribuidor de servicio
autorizado de Briggs & Stratton.
Recomendaciones acerca del
combustible
El combustible debe cumplir estos requisitos:
• Gasolina limpia, fresca y sin plomo.
• Un mínimo de 87 octanos u 87 AKI (91 RON). Para uso en grandes alturas,
consulte a continuación.
• Se acepta gasolina con hasta un 10% de etanol (gasohol).
AVISO No utilice gasolinas no aprobadas, como la E15 y la E85. No mezcle la
gasolina con aceite ni modifique el motor para usarlo con combustibles alternativos.
El uso de combustibles no aprobados puede dañar los componentes del motor, lo
que no está cubierto por la garantía.
Para proteger el sistema de combustible de la formación de goma, mezcle el
combustible con un estabilizador. VéaseAlmacenamiento.No todo el combustible
es igual. Si ocurren problemas de arranque o de rendimiento, cambie el proveedor
o la marca del combustible. Este motor está certificado para funcionar con gasolina.
El sistema de control de emisiones para motores carburados es EM (modificaciones
del motor). Los sistemas de control de emisiones para motores con inyección de
combustible electrónica son ECM (módulo de control del motor), MPI (inyección
multipuerto) y, si lo tiene, un O2S (sensor de oxígeno).
Gran altitud
En alturas de más de 5.000 pies (1524 metros), una gasolina con un mínimo de 85
octano/85 AKI(89 RON) es aceptable.
Para motores carburados es necesario el ajuste para gran altitud a fin de conservar el
rendimiento. El funcionamiento sin este ajuste genera una disminución del rendimiento,
un aumento del consumo de combustible y un incremento en las emisiones. Para
Not for
Reproduction
17
obtener información sobre el ajuste de alta altitud, póngase en contacto con un
distribuidor de servicio autorizado de Briggs & Stratton. No se recomienda operar el
motor a alturas inferiores a los 762 metros (2500 pies) con el ajuste para gran altura.
Para los motores de con inyección electrónica de combustible (EFI), no es necesario
ningún ajuste para gran altitud.
Cómo agregar combustible
Vea la figura: 6
ADVERTENCIA
El combustible y sus vapores son extremadamente inflamables y explosivos.
Un incendio o una explosión pueden causar graves quemaduras o la muerte.
Al agregar combustible
• Apague el motor y deje que se enfríe por lo menos 2 minutos antes de remover la
tapa del combustible.
• Llene el tanque de combustible en exteriores o en un área bien ventilada.
• No llene excesivamente el tanque de combustible. Para permitir la expansión
del combustible no llene por encima de la parte inferior del cuello del tanque de
combustible.
• Mantenga el combustible alejado de chispas, llamas abiertas, testigos piloto,
fuentes de calor y otras fuentes de encendido.
• Compruebe con frecuencia si existen grietas o fugas en las mangueras de
combustible, el tanque, la tapa y en los accesorios. Cámbielos si es necesario.
• Si se derramó combustible, espere hasta que se haya evaporado antes arrancar
el motor.
1. Limpie la tierra y la suciedad del área de la tapa del combustible. Retire la tapa del
combustible.
2. Llene el tanque de combustible (A, Figura 6) con combustible. Para permitir la
expansión del combustible no llene por encima de la parte inferior del cuello del
tanque de combustible (B).
3. Re-instale la tapa de combustible.
Arranque y parada del motor
Vea la figura: 7, 8, 9
Arranque del motor
ADVERTENCIA
La retracción rápida de la cuerda de arranque (contragolpe) le halará la mano y
el brazo hacia el motor más rápido de lo que usted la pueda dejar ir.
Podrían ocasionarse roturas de huesos, fracturas, moretones o torceduras.
• Cuando arranque el motor, tire lentamente de la cuerda hasta sentir resistencia y,
a continuación, tire rápidamente de ella para evitar su retroceso.
ADVERTENCIA
El combustible y sus vapores son extremadamente inflamables y explosivos.
Un incendio o una explosión pueden causar graves quemaduras o la muerte.
Cuando le de arranque al motor
• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el purificador
de aire (si tiene) estén colocados de modo seguro en su lugar.
• No haga girar el motor si retiró la bujía.
• Si el motor se inunda, ajuste el estrangulador (si está equipado) en la posición
OPEN/RUN, coloque el acelerador (si está equipado) en la posición FAST y haga
girar el motor hasta que arranque.
ADVERTENCIA
PELIGRO DE GAS TÓXICO. El escape del motor contiene monóxido de
carbono, un gas tóxico que puede matar en minutos. NO puede verlo, es
inodoro e insípido. Incluso si no huele los gases del escape, puede estar
expuesto al monóxido de carbono. Si comienza a sentirse mareado o débil
cuando utiliza este producto, apáguelo y tome aire fresco INMEDIATAMENTE.
Consulte a un médico. Puede haberse intoxicado con monóxido de carbono.
• Opere este producto SOLAMENTE al aire libre, lejos de ventanas, puertas y
ventilaciones, para reducir el riesgo de que el monóxido de carbono se acumule y
pueda circular a espacios habitados.
• Instale alarmas de monóxido de carbono con baterías o enchufe (batería de
respaldo) siguiendo las instrucciones del fabricante. Las alarmas de humo no
pueden detectar el monóxido de carbono.
• NO opere este producto dentro de hogares, garajes, sótanos, espacios reducidos,
cobertizos u otros espacios parcialmente cerrados, incluso si usa ventiladores o
deja las puertas y ventanas abiertas. El monóxido de carbono se puede acumular
rápidamente en estos espacios y puede permanecer durante horas, incluso
después de que se apaga este producto.
• SIEMPRE coloque este producto en la dirección del viento y apunte el escape del
motor lejos de espacios habitados.
AVISO Este motor fue enviado desde Briggs & Stratton sin aceite. Antes de
arrancar el motor, asegúrese de agregar aceite según las instrucciones de este
manual. Si arranca el motor sin aceite, sufrirá daños irreparables que la garantía no
cubrirá.
Identificación del sistema de arranque.
Antes de arrancar el motor, deberá identificar el tipo de sistema de arranque que tiene
su motor. Su motor tendrá uno de los siguientes tipos.
•
Sistema ReadyStart
®
: Presenta un estrangulador automático controlado por
temperatura. No tiene un estrangulador manual ni un cebador.
• Sistema con estrangulador: Este sistema cuenta con un estrangulador que
se usa para el arranque a temperaturas bajas. Algunos modelos tendrán un
control del estrangulador separado, mientras que otros tendrán un control de
combinación para estrangulador / acelerador. Este tipo no tiene un cebador.
Para arrancar su motor, siga las instrucciones de su tipo de sistema de arranque.
Nota:El equipo puede tener controles remotos. Consulte el manual del equipo para
conocer la ubicación y el funcionamiento de los controles remotos.
Sistema ReadyStart
®
1. Verifique el nivel de aceite en el motor. Consulte la sección Comprobación del
nivel de aceite .
2. Asegúrese que los controles de transmisión del equipo, si están equipados, estén
desconectados.
3. Mueva la válvula de cierre de combustible (A, Figura 7), si existe, a la posición
OPEN.
4. Mueva el control del acelerador (B, Figura 7, 8), si tiene, a la posición FAST.
Opere el motor en la posición de velocidad rápida (FAST).
5. Mueva el suiche de parada (D, Figura 7, 8), si tiene, a la posición ON.
6. Si el producto está equipado con palanca de detención del motor (C, Figura 9),
sostenga la palanca de detención del motor contra la manija.
7. Arranque por rebobinado, si está equipado: Sostenga firmemente la cuerda de
arranque (E, Figura 7, 8). Tire lentamente de la cuerda de arranque hasta sentir
una resistencia y, a continuación, tire de ella rápidamente.
ADVERTENCIA
La retracción rápida de la cuerda de arranque (retroceso violento) le halará la mano
y el brazo hacia el motor antes de que pueda soltarla. Podrían ocasionarse roturas
de huesos, fracturas, moretones o torceduras. Cuando arranque el motor, tire
lentamente de la cuerda hasta sentir resistencia y, a continuación, tire rápidamente
de ella para evitar su retroceso.
8. Arranque eléctrico, si está equipado: Gire el suiche de arranque eléctrico a la
posición ON/START.
AVISO Para prolongar la vida del arranque, utilice ciclos de arranque cortos
(máximo de cinco segundos). Espere un minuto entre ciclos de arranque.
Nota:Si el motor no arranca después de varios intentos, póngase en contacto con su
distribuidor local o vaya a BRIGGSandSTRATTON.COM o llame al 1-800-233-3723
(en EE.UU.).
Sistema con estrangulador
1. Verifique el nivel de aceite en el motor. Consulte la sección Comprobación del
nivel de aceite .
2. Asegúrese que los controles de transmisión del equipo, si están equipados, estén
desconectados.
3. Mueva la válvula de cierre de combustible (A, Figura 7), si tiene, a la posición
OPEN.
4. Mueva el control del acelerador (B, Figura 7, 8), si está equipado, a la posición
FAST. Opere el motor en la posición de velocidad rápida (FAST).
5. Mueva el control del estrangulador (F, Figura 7) a la posición CLOSED.
Nota:Generalmente no es necesario el estrangulador para volver a arrancar un motor
caliente.
Not for
Reproduction
18 BRIGGSandSTRATTON.COM
6. Si el producto está equipado con una palanca de detención del motor (C, Figura
9), sostenga la palanca de detención del motor contra la manija.
7. Arranque por rebobinado, si está equipado: Sostenga firmemente la manija de
la cuerda de arranque (E, Figura 7, 8). Tire lentamente de la cuerda de arranque
hasta sentir una resistencia y, a continuación, tire de ella rápidamente.
ADVERTENCIA
La retracción rápida de la cuerda de arranque (retroceso violento) le halará la mano
y el brazo hacia el motor antes de que pueda soltarla. Podrían ocasionarse roturas
de huesos, fracturas, moretones o torceduras. Cuando arranque el motor, tire
lentamente de la cuerda hasta sentir resistencia y, a continuación, tire rápidamente
de ella para evitar su retroceso.
8. Arranque eléctrico, si está equipado: Gire el suiche de arranque eléctrico a la
posición ON/START.
AVISO Para prolongar la vida del arranque, utilice ciclos de arranque cortos
(máximo de cinco segundos). Espere un minuto entre ciclos de arranque.
9. A medida que se caliente el motor, mueva el control del estrangulador (F, Figura
7) a la posición OPEN/RUN.
Nota:Si el motor no arranca después de varios intentos, póngase en contacto con su
distribuidor local, o vaya a BRIGGSandSTRATTON.COM o lllame al 1-800-233-3723
(en EE.UU.).
Parada del motor
ADVERTENCIA
El combustible y sus vapores son extremadamente inflamables y explosivos.
Un incendio o una explosión pueden causar graves quemaduras o la muerte.
• No estrangule el carburador para detener el motor
1. Palanca de parada del motor, si tiene: Suelte la palanca de parada del motor
(E, Figura 9).
Suiche de parada, si tiene: Mueva el suiche de parada (D, Figura 7, 8) a la
posición OFF.
Control del acelerador, si tiene: Mueva el control del acelerador (B, Figura 7, 8)
a la posición de parada (STOP).
Llave para arranque eléctrico, si está equipado: Gire la llave para arranque
eléctrico a la posición OFF / STOP. Retire la llave y guárdela en un lugar seguro
fuera del alcance de los niños.
2. Una vez que se detenga el motor, mueva la válvula de cierre de combustible (A,
Figura 7), si está equipada, a la posición CLOSED.
Mantenimiento
AVISO Si el motor se inclina durante el mantenimiento, el tanque de combustible,
si está montado en el motor, se debe vaciar y el lado de la bujía debe estar hacia
arriba. Si el tanque de combustible no está vacío y si el motor se inclina en cualquier
otra dirección, puede resultar difícil arrancarlo debido a que el aceite o la gasolina
contaminan el filtro de aire o la bujía.
ADVERTENCIA
Al realizar trabajos de mantenimiento que requieran inclinar la unidad, el tanque de
combustible, si está montado en el motor, debe estar vacío o podría haber una fuga
de combustible y generar un incendio o una explosión.
Le recomendamos que consulte a cualquier distribuidor autorizado de Briggs & Stratton
para el mantenimiento y reparación del motor y para obtener piezas del motor.
AVISO Todos los componentes utilizados para construir este motor deben
permanecer en su lugar para su correcto funcionamiento.
ADVERTENCIA
Un chispeo involuntario puede producir un incendio o una descarga eléctrica.
Una puesta en marcha involuntaria puede causar enredos, amputaciones
traumáticas o laceraciones.
Peligro de incendio
Antes de hacer ajustes o reparaciones:
• Desconecte el cable de la bujía y manténgalo lejos de la bujía.
• Desconecte la batería en la terminal negativa (únicamente motores con arranque
eléctrico).
• Use solamente las herramientas correctas.
• No manipule el resorte del regulador, las conexiones u otras piezas para
aumentar la velocidad del motor.
• Las piezas de repuesto deben ser del mismo diseño y deben ser instaladas en la
misma posición que las piezas originales. Otras piezas pueden no funcionar igual
de bien, pueden dañar la unidad, y pueden causar lesiones.
• No golpee el volante con un martillo o un objeto duro, porque el volante más tarde
puede romperse durante la operación.
Cuando compruebe chispa:
• Use un comprobador de bujías aprobado.
• No haga las pruebas de chispa sin la bujía en su lugar.
Servicio de control de emisiones
Cualquier establecimiento o individuo especializado en la reparación de motores
que no sean de automoción puede encargarse del mantenimiento, la sustitución
y la reparación de los dispositivos y sistemas de control de emisiones. Sin
embargo, para recibir el servicio de control de emisiones "sin cargo", debe realizarlo un
distribuidor autorizado por la fábrica. Ver Declaraciones de Control de Emisiones.
Plan de mantenimiento
Las Primeras 5 horas
• Cambie el aceite
Cada 8 Horas o diariamente
• Compruebe el nivel del aceite del motor
• Limpie el área alrededor del mofle y los controles
• Limpie la rejilla de admisión de aire
Cada 50 horas o anualmente
•
Limpie el filtro de aire
1
•
Limpie el pre-filtro (si está equipado)
1
• Cambie el aceite del motor
• Reemplace el filtro de aceite (si está equipado)
• Realice el mantenimiento del sistema de escape
Cada 200 horas
•
Sustituya el filtro de aire
1
•
Sustituya el pre-filtro (si está equipado)
1
Anualmente
• Sustituya las bujías
• Realice el mantenimiento del sistema de combustible
•
Realice el mantenimiento del sistema de enfriamiento
1
•
Verifique el espacio libre de la válvula
2
1
Limpie con mayor frecuencia en condiciones de mucho polvo o cuando el aire
contenga muchas partículas.
2
No se requiere a menos que se detecten problemas de desempeño en el motor.
Velocidad del motor y carburador
Nunca realice ajustes a la velocidad del motor o carburador. El carburador ha
sido calibrado en la fábrica para funcionar de manera óptima en la mayoría de las
condiciones de uso. No interfiera con el resorte del regulador, las varillas u otras partes
a fin de modificar la velocidad del motor. Si son necesarios ajustes póngase en contacto
con un Distribuidor de Servicio Autorizado de Briggs & Stratton para que le presten el
servicio.
AVISO El fabricante del equipo especifica la velocidad máxima del motor como
está instalado en el equipo. No exceda esta velocidad. Si no está seguro de cuál
es la velocidad máxima del equipo, o cuál era la velocidad del motor ajustada en la
fábrica, póngase en contacto con un Distribuidor de Servicio Autorizado de Briggs
& Stratton para obtener ayuda. Para un funcionamiento seguro y adecuado del
equipo, la velocidad del motor debe ser ajustada solamente por un técnico de servicio
calificado.
Not for
Reproduction
19
Revisión de la bujía
Vea la figura: 10
Revise el entre-hierro (A, Figura 10) con un calibrador de alambre (B). Si es necesario,
vuelva a establecer la distancia. Instale y ajuste la bujía al par recomendado. Para el
ajuste del entre-hierro o el par de apriete, consulte la sección Especificaciones .
Nota:En algunas áreas, las leyes locales requieren el uso de una bujía con resistencia
para suprimir las señales de encendido. Si este motor vino originalmente equipado con
una bujía con resistencia, use el mismo tipo de bujía cuando la reemplace.
Realice el mantenimiento del sistema de
escape
ADVERTENCIA
El funcionamiento de los motores produce calor. Las partes de los motores,
especialmente el silenciador, se calientan demasiado.
Pueden ocurrir graves quemaduras a causa de su contacto.
Desechos combustibles, tal como hojas, grama, maleza, etc. pueden alcanzar a
encenderse.
• Deje que el silenciador, el cilindro y las aletas del motor se enfríen antes de
tocarlos.
• Extraiga los desechos acumulados en el área del silenciador y en el área del
cilindro.
• Es una violación del Código de Recursos Públicos de California, Sección 4442,
utilizar u operar el motor en cualquier espacio con árboles, maleza o grama a
menos que el sistema de escape esté equipado con un extintor de chispas, como
lo define la Sección 4442, mantenido en correcto funcionamiento. Otros estados o
jurisdicciones federales pueden tener leyes similares. Póngase en contacto con el
vendedor, el distribuidor o el fabricante del equipo original para obtener un extintor
de chispas diseñado para el sistema de escape instalado en este motor.
Extraiga los desechos acumulados en el área del silenciador y en el área del cilindro.
Inspeccione el silenciador en busca de grietas, corrosión u otros daños. Quite el
deflector o el extintor de chispas (B), si tiene, e inspecciónelo para ver si hay daños o
bloqueo de carbono. Si se detecta algún daño, instale las piezas de repuesto antes de
poner el motor en funcionamiento.
ADVERTENCIA
Las piezas de repuesto deben ser del mismo diseño y deben ser instaladas en la
misma posición que las piezas originales. Otras piezas pueden no funcionar igual de
bien, pueden dañar la unidad, y pueden causar lesiones.
Cambio de aceite del motor
Vea la figura: 11, 12, 13, 14
ADVERTENCIA
El combustible y sus vapores son extremadamente inflamables y explosivos.
Un incendio o una explosión pueden causar graves quemaduras o la muerte.
El funcionamiento de los motores produce calor. Las partes de los motores,
especialmente el silenciador, se calientan demasiado.
Pueden ocurrir graves quemaduras a causa de su contacto.
• Cuando drene el aceite por el tubo superior de llenado, el tanque de combustible
debe estar vacío o el combustible puede derramarse y causar un incendio o una
explosión.
• Deje que el silenciador, el cilindro y las aletas del motor se enfríen antes de
tocarlos.
El aceite usado es un peligroso producto de desecho y debe eliminarse en forma
adecuada. No lo deseche con los residuos domésticos. Consulte con sus autoridades
locales, su centro de servicio, o su distribuidor para conocer las instalaciones para su
disposición/reciclaje seguro.
Remoción del Aceite
1. Con el motor apagado pero aún caliente, desconecte el(los) cable(s) de bujía (D,
Figura 11) y aléjelo(s) de la(s) bujía(s) (E).
2. Retire la varilla indicadora de nivel de aceite (A, Figura 12).
3. Quite el tapón de drenaje de aceite (F, Figura 13). Drene el aceite en un recipiente
aprobado.
Nota:Cualquiera de los tapones de drenaje de aceite (G, Figura 13) se puede instalar
en el motor.
4. Después de haber drenado el aceite, instale y apriete el tapón de drenaje de
aceite (F, Figura 13).
5. Cuando drene el aceite desde el tubo superior de llenado de aceite (C, Figura 14),
mantenga el extremo de la bujía (E) del motor hacia arriba. Drene el aceite en un
recipiente aprobado.
ADVERTENCIA
Cuando drene el aceite por el tubo superior de llenado, el tanque de combustible
debe estar vacío o el combustible puede derramarse y causar un incendio o una
explosión. Para vaciar el tanque de combustible. Opere el motor hasta que se
detenga por falta de combustible.
Cambie el Filtro de aceite, si está equipado
Algunos modelos vienen equipados con un filtro de aceite. Para obtener los intervalos
de reemplazo, consulte el Plan de mantenimiento.
1. Escurra el aceite del motor. Ver la sección Remoción del Aceite .
2. Quite el filtro de aceite (H, Figura 12) y deséchelo de forma adecuada.
3. Antes de instalar el nuevo filtro de aceite, lubrique ligeramente el empaque del
filtro de aceite con aceite fresco y limpio.
4. Instale el filtro de aceite con la mano hasta que el empaque haga contacto con el
adaptador de filtro de aceite, luego apriete el filtro de aceite de 1/2 a 3/4 de vuelta.
5. Agregue aceite. Ver la sección Agregar aceite .
6. Arranque y haga funcionar el motor. A medida que el motor se caliente, verifique
que no haya fugas de aceite.
7. Detenga el motor y verifique el nivel de aceite. El nivel de aceite debe estar en la
parte superior del indicador de lleno (B, Figura 12) sobre la varilla indicadora de
nivel de aceite.
Aprovisionamiento de Aceite
• Asegúrese de que el motor esté nivelado.
• Limpie todos los desechos del área de llenado de aceite.
• Consulte la sección de Especificaciones para obtener la capacidad de aceite.
1. Quite la varilla indicadora de nivel (A, Figura 12) y límpiela con un paño limpio.
2. Agregue aceite lentamente en el llenado de aceite del motor (C, Figura 12). No
llene en exceso. Después de añadir aceite, espere un minuto y luego compruebe
el nivel de aceite.
3. Instale y apriete la varilla indicadora de nivel de aceite (A, Figura 12).
4. Retire la varilla y verifique el nivel de aceite. El nivel de aceite debe estar en la
parte superior del indicador de lleno (B, Figura 12) sobre la varilla indicadora de
nivel de aceite.
5. Vuelva a instalar y ajuste la varilla indicadora de nivel de aceite (A, Figura 12).
6. Conecte el(los) cables de las bujías (D, Figura 11) a la(s) bujía(s) (E).
Mantenimiento del filtro de aire
Vea la figura: 15, 16
ADVERTENCIA
El combustible y sus vapores son extremadamente inflamables y explosivos.
Un incendio o una explosión pueden causar graves quemaduras o la muerte.
• Nunca encienda o haga funcionar el motor sin el conjunto del purificador de aire
(si tiene) o el filtro de aire (si tiene).
AVISO No use aire comprimido ni solventes para limpiar el filtro. El aire comprimido
puede dañar el filtro y los solventes lo disuelven.
Consulte el Plan de mantenimiento para conocer los requerimientos de servicio.
Varios modelos usan filtros de espuma o de papel. Algunos modelos además pueden
tener un pre-purificador adicional que puede lavarse y volver a usar. Compare
las ilustraciones de este manual con el tipo instalado en su motor y realice el
mantenimiento como se indica a continuación.
Not for
Reproduction
20 BRIGGSandSTRATTON.COM
Filtro de aire
1. Mueva el seguro deslizante (A, Figura 15) a la posición de desbloqueo y abra la
cubierta (B).
2. Para evitar que caigan escombros en el carburador, retire con cuidado el
elemento de espuma (C, Figura 15) de la base del filtro de aire.
3. Lave el elemento de espuma (C, Figura 15) en detergente líquido y agua. Seque
(presionado) el elemento de espuma con un paño limpio.
4. Empape el elemento de espuma (C, Figura 15) con aceite de motor limpio. Para
quitar el exceso de aceite de motor, escurra el elemento de espuma en un paño
limpio.
5. Instale el elemento de espuma (C, Figura 15) sobre la base del filtro de aire.
6. Cierre la tapa (B, Figura 15) y mueva el seguro deslizante (A) a la posición
enclavada.
Filtro de aire de papel
1. Afloje el(los) sujetador(es) (A, Figura 16).
2. Retire la cubierta (B, Figura 16).
3. Para evitar que caigan residuos al carburador, retire con cuidado el pre filtro (D,
Figura 16) y el filtro (C) de la base del filtro de aire.
4. Retire el pre-filtro (D, Figura 16) del filtro (C).
5. Golpetee el filtro contra una superficie dura (C, Figura 16para desprender los
residuos. Si el filtro está excesivamente sucio, cámbielo por otro nuevo.
6. Lave el pre-filtro (D, Figura 16) en detergente líquido y agua. Luego deje que el
pre-filtro se seque al aire completamente. No engrase el pre-filtro.
7. Incorpore el pre-filtro limpio (D, Figura 16) al filtro (C).
8. Instale el filtro (C, Figura 16) y el pre filtro (D) sobre la base del filtro de aire.
Asegúrese de que el filtro ajuste de forma segura sobre la base del filtro de aire.
9. Instale la cubierta (B, Figura 16) y asegure con el(los) sujetador(es) (A).
Asegúrese de que todos estén bien ajustados.
Mantenimiento del sistema de
combustible
Consulte la figura: 17
ADVERTENCIA
El combustible y sus vapores son extremadamente inflamables y explosivos.
El fuego o la explosión pueden causar quemaduras graves o la muerte.
• Mantenga el combustible alejado de chispas, llamas abiertas, testigos piloto,
fuentes de calor y otras fuentes de encendido.
• Compruebe con frecuencia si existen grietas o fugas en las mangueras de
combustible, el tanque, la tapa y en los accesorios. Reemplace las piezas, si es
necesario.
• Antes de limpiar o reemplazar el filtro, drene el tanque de combustible o cierre la
válvula de cierre de combustible.
• Si se derramó combustible, espere hasta que se haya evaporado antes arrancar
el motor.
• Las piezas de repuesto deben ser iguales y se deben instalar en la misma
posición que las piezas originales.
Filtro de Combustible, si está equipado
1. Antes de limpiar o reemplazar el filtro de combustible (A, Figura 17), drene
el tanque de combustible o cierre la válvula de cierre de combustible. De lo
contrario, puede presentarse una fuga de combustible y causar un incendio o una
explosión.
2. Use pinzas para agarrar las pestañas (B, Figura 17) sobre las abrazaderas (C),
luego aleje las abrazaderas del filtro de combustible (A). Retire las mangueras de
combustible (C) del filtro de combustible.
3. Inspeccione las líneas de combustible (D, Figura 17) en busca de grietas o fugas.
Cámbielos si es necesario.
4. Reemplace el filtro de combustible (A, Figura 17) con un filtro de repuesto
genuino.
5. Asegure las líneas de combustible (D, Figura 17) con abrazaderas (C) como se
muestra.
Mantenimiento del sistema de
enfriamiento
ADVERTENCIA
El funcionamiento de los motores produce calor. Las partes de los motores,
especialmente el silenciador, se calientan demasiado.
Pueden ocurrir graves quemaduras a causa de su contacto.
Los desechos combustibles, tal como hojas, grama, maleza, etc. se pueden
encender.
• Deje que el silenciador, el cilindro y las aletas del motor se enfríen antes de
tocarlos.
• Extraiga los desechos acumulados en el área del silenciador y en el área del
cilindro.
AVISO No use agua para limpiar el motor. El agua puede contaminar el sistema de
combustible. Use un cepillo o un paño húmedo para limpiar el motor.
El motor es refrigerado por aire. La suciedad o los desechos pueden limitar el flujo de
aire y provocar que el motor se sobrecaliente, lo cual disminuye su rendimiento y su
vida útil.
1. Utilice un cepillo o paño seco para remover los desechos del área de la admisión
de aire.
2. Mantenga las conexiones, los resortes y los controles limpios.
3. Elimine los restos de combustible de la zona de alrededor y de la parte posterior
del silenciador.
4. Asegúrese de que las aletas del enfriador de aceite, si tiene, no presenten
suciedad ni residuos.
Después de un período de tiempo, se pueden acumular residuos en las aletas de
enfriamiento del cilindro y causar el sobrecalentamiento del motor. Los residuos no
se pueden eliminar mientras no se desmonte parcialmente el motor. Solicite a un
distribuidor autorizado de Briggs & Stratton que inspeccione y limpie el sistema de
enfriamiento de aire según las recomendaciones del Plan de mantenimiento.
Almacenamiento
ADVERTENCIA
El combustible y sus vapores son extremamente inflamables y explosivos.
El fuego o la explosión pueden causar quemaduras graves o la muerte.
Cuando almacene el combustible o el equipo con combustible en el tanque
• Almacene lejos de hornos, estufas, calentadores de agua u otros aparatos
que utilicen testigos piloto u otras fuentes de encendido ya que estos pueden
encender los vapores combustibles.
Sistema de combustible
Vea la figura:18
Almacene el nivel del motor (posición de operación normal). Llene el tanque de
combustible (A, figura18) con combustible. Para permitir la expansión del combustible,
no llene en exceso el tanque por encima del cuello del tanque de combustible (B).
El combustible puede echarse a perder cuando se conserva en un contenedor de
almacenamiento durante más de 30días. Cada vez que llene el contenedor con
combustible, agregueSTA-BIL 360°
®
PROTECTION™al combustible tal como se
especifica en las instrucciones del fabricante. Esto lo mantiene fresco y disminuye
los problemas relacionados con el combustible o la contaminación en el sistema de
combustible.
No es necesario drenar el combustible del motor cuandoSTA-BIL
360°
®
PROTECTION™el se agrega según las instrucciones. Antes de su
almacenamiento, ENCENDIDO el motor durante 2minutos para que el combustible y el
estabilizador recorran todo el sistema de combustible.
Si la gasolina en el motor no fue tratada con un estabilizador de combustible, deberá
vaciarla en un recipiente aprobado. Haga funcionar el motor hasta que se detenga
por falta de combustible. Se recomienda usar un estabilizador de combustible en el
recipiente de almacenamiento para mantener la frescura del combustible.
Aceite del Motor
Cambie el aceite del motor mientras que el motor se encuentre todavía caliente.
Consulte la sección Cambio de aceite del motor .
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Simplicity 150000 Manuel utilisateur
- Catégorie
- Accessoires pour véhicules automobiles
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Simplicity 150000 User manual
- español: Simplicity 150000 Manual de usuario