Simplicity 094212-0205-E1 Manuel utilisateur

Marque: Simplicity

Modèle: 094212-0205-E1

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Model Series

Covered in

This Manual

90000

Operating & Maintenance

Instructions

Model Type Code

Month Day Year

Note: General Model Series numbers noted above are inclusive of the specific model

number found on your engine. To get replacement parts or technical assistance in

the future, write your engine Model, Type, Code and date of purchase here.

TABLE OF CONTENTS

Emission 2.................................

Safety 3-5.................................

Technical Information 5......................

Engine Information 6........................

Oil 7.......................................

Fuel 8.....................................

Starting Information 9.......................

Maintenance 10-13.........................

Parts and Service & Storage 14...............

Warranty Information 15.....................

WARNING

Briggs&Strattondoesnotapproveorauthorizetheuseoftheseengines

on 3-wheel All TerrainVehicles (A TVs), motor bikes, aircraft products or

vehicles intended for use incompetitive events.Use ofthese engines in

such applications could result in property damage, serious injury

(including paralysis), or even death.

Need assistance? Go to www.briggsandstratton.com

for detailed information regarding

Briggs & Stratton engines.

Or c a ll,

1-800-233-3723, (U.S.A. and Canada)

to hear a menu of pre-recorded messages

offering engine maintenance information.

The Power That Works For You.

After July 1, 2000, Look For Emissions Compliance Period On

Engine Emissions Compliance Label

After July 1, 2000 certain Briggs & Stratton engines will be certified to meet the United States Environmental Protection

Agency (USEPA) Phase 2 emission standards. ForPhase 2 certified engines,the EmissionsCompliance Periodreferred

to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to

meet Federalemissionrequirements. Forengineslessthan225cc displacement, Category C= 125hours, B= 250hours

and A = 500 hours. For engines of 225 cc or more, Category C = 250 hours, B = 500 hours and A = 1000 hours.

The displacement of Model Series 90000 engine is 148 cc.

This is a generic representation

of the emission label typically

found on a certified engine.

BEFORE OPERATING ENGINE

• Read entire Operating & Maintenance Instructions AND

the instructions for the equipment this engine powers.*

• Failure to follow instructions could result in serious injury

or death.

THE OPERATING & MAINTENANCE INSTRUCTIONS

CONTAIN SAFETY INFORMATION TO

• Make you aware of hazards associated with engines

• Inform you of the risk of injury associated with those hazards, and

• Tell you how to avoid or reduce the risk of injury.

275909

The safety alert symbol ( )is used to identify safety

informationabouthazardsthatcanresultinpersonalinjury.

A signal word (DANGER, W ARNING, or CAUTION) is

used with the alertsymbol toindicate thelikelihood andthe

potential severity of injury. In addition, a hazard symbol

may be used to represent the type of hazard.

DANGER indicates a hazard which, if not

avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, might result in minor or moderate

injury.

CAUTION,whenusedwithoutthealertsymbol,

indicates a situation that could result in damage

to the engine.

WARNING

The engine exhaust from this prod-

uct contains chemicals known to the

State of California to cause cancer,

birth defects, or other reproductive

harm.

HAZARD SYMBOLS AND MEANINGS

Explosion

Toxic Fumes

Moving Parts

ShockHot Surface

Kickback

Fire

THE INTERNATIONAL SYMBOLS USED

ON THE ENGINE OR

IN THIS MANUAL INCLUDE:

On Off

Fuel Shutoff

Read Owner’s

Manual

Stop Fuel

Choke

Safety Alert

Oil

* Briggs & Stratton does not necessarily know what equipment this engine will power. For that reason, you should carefully read

and understand the operating instructions for the equipment on which your engine is placed.

SAFETY

Gasoline and its vapors are extremely

flammable and explosive.

Fireorexplosioncancausesevereburns

or death.

WARNING

WHEN ADDING FUEL

• Turn engine OFF and let engine cool at least 2

minutes before removing gas cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. Fill tank to approximately

1-1/2 inches below top of neck to allow for fuel

expansion.

• Keep gasoline away from sparks, open flames,

pilot lights, heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently

for cracks or leaks. Replace if necessary.

WHEN STARTING ENGINE

• Make sure spark plug, muffler, fuel cap and air

cleaner are in place.

• Do not crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting

engine.

• If engine floods, set choke to OPEN/RUN position,

placethrottleinFAST andcrank until enginestarts.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which

causes gasoline to spill.

• Do not choke carburetor to stop engine.

WHEN TRANSPORTING EQUIPMENT

• TransportwithfueltankEMPTYorwithfuelshut-off

valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT

WITH FUEL IN TANK

• Storeawayfromfurnaces, stoves,waterheatersor

other appliances that have pilot light or other

ignition source because they can ignite gasoline

vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable

gases.

Explosion and fire could result.

WARNING

• If there is natural or LP gas leakage in area, donot

start engine.

• Do not use pressurized starting fluids because

vapors are flammable.

WARNING

Rapid retraction of starter cord (kickback) will

pull hand and arm toward engine faster than

you can let go.

Broken bones, fractures, bruises or sprains

could result.

• When starting engine, pull cord slowly until

resistance is felt, then pull rapidly.

• Remove all external equipment/engine loads

before starting engine.

• Direct coupled equipment components such as,

but not limited to, blades, impellors, pulleys,

sprockets, etc., must be securely attached.

WARNING

Rotating parts can contact or entangle

hands, feet, hair , clothing, or accessories.

T raumatic amputation or severe laceration

can result.

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling

drawstrings or items that could become caught.

SAFETY

Engines give off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause

nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

WARNING

Running engines produce heat. Engine

parts,especiallymuffler ,becomeextremely

hot.

Severethermalburnscanoccuroncontact.

Combustible debris, such as leaves, grass,

brush, etc. can catch fire.

• Allow muffler, engine cylinder and fins to cool

before touching.

• Remove accumulated combustibles from muffler

area and cylinder area.

• Install and maintain in working order a spark

arresterbeforeusingequipmentonforest-covered,

grass-covered, brush-covered unimproved land.

The state of California requires this (Section 4442

of the California Public Resources Code). Other

states may have similar laws. Federal laws apply

on federal land.

WARNING

Unintentional sparking can result in fire or

electric shock.

Unintentional start-up can result in en-

tanglement, traumatic amputation, or lac-

eration.

BEFORE PERFORMING ADJUSTMENTS OR

REPAIRS

• Disconnect spark plug wire and keep it away from

spark plug.

• Disconnect battery at negative terminal (only

engines with electric start).

WHEN TESTING FOR SPARK

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

ENGINE INFORMATION

TECHNICAL INFORMATION

POWER RATINGS: The power ratings for an individual engine

modelareinitiallydevelopedbystartingwithSAE(SocietyofAuto-

motive Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure)(Revision2002-05).Givenboththewidearray

ofproductsonwhichourenginesareplaced,andthevarietyofen-

vironmental issues applicable to operating the equipment, itmay

be that the engine you have purchased will notdevelop therated

horsepowerwhenusedinapieceofpowerequipment(actual“on-

site”power).Thisdifferenceisduetoavarietyoffactorsincluding,

but not limited to, the following: differences in altitude, tempera-

ture,barometricpressure,humidity,fuel,engine lubrication,maxi-

mumgovernedenginespeed,individualenginetoenginevariabil-

ity,design oftheparticularpieceof powerequipment,themanner

in which the engine is operated, engine run-in to reduce friction

andcleanoutofcombustionchambers,adjustmentstothevalves

and carburetor,and otherfactors. Thepowerratings may alsobe

adjusted based on comparisons to other similar engines utilized

insimilarapplications,andwillthereforenotnecessarilymatchthe

values derived using the foregoing codes.

ENGINE PARTS

1. Rope Handle for Rewind Starter

2. Oil Drain Plug

3. Choke control lever

4. Throttle lever

5. Air Cleaner

6. Fuel Tank Cap

7. Spark plug / Spark plug wire

8. Muffler

9. Engine

Model T ype Code

xxxxx xxxx xx xxxxxxxx

10. Stop Switch Wire (if equipped)

11. Oil fill cap

12. Fuel Fill

13. Throttle/Choke Control

14. Air Cleaner

15. Stop Switch

GENERAL INFORMATION

ENGINE MODEL

Thisisasinglecylinder,L-head,air-cooledengine.Itisalowemis-

sions engine.

MODEL SERIES 90000

Bore 2-9/16 in. (65.09 mm)..............................

Stroke 1-3/4 in. (44.45 mm).............................

Displacement 9.02 cu. in. (148.0 cc).....................

TUNE -UP SPECIFICATIONS

Armature air gap 0.006 -- 0.010 in. (0.15 -- 0.25 mm).........

Spark plug gap 0.030 in. (0.76 mm).......................

Valve clearancew i t hvalve spr i ngsinstal l edandpiston1/4in.(6 mm)

past top dead center (check when engine is cold). See Repair

Manual P/N 270962.

Intake 0.005 -- 0.007 in. (0.13 -- 0.18 mm).................

Exhaust 0.007 -- 0.009 in. (0.18 -- 0.23 mm)...............

For pr act i cal operat i on, the horsepower loading shoul d not exceed

85% of rat ed horsepower. Engine power wil l decr ease 3-1/2% for

each 1, 000feet(300 meter s)above seal eveland 1% f oreach 10° F

(5.6° C) above 77° F(25° C). Engine will operat e sati sf act ori l y at an

angle up t o 15°.

OIL

275909

CAUTION: This engine is shipped from Briggs &

Strattonwithout oil

. Check oil level before starting

engine.If youstart theenginewithout oil, theengine

will be damaged beyond repair and will not be

covered under warranty.

Note: If this engine is equipped with gear reduction, gear

reduction case must be filled with oil prior to operating en-

gine. See gear reduction oil filling instructions on page 12.

OIL CAPACITY

The engine holds approximately 2/3 qt (21 ozs; 0.6 liter).

TYPE OF OIL TO USE

• Use a high quality detergent oil classified “For Service

SF,SG,SH, SJ”orhigher, suchasBriggs& Stratton30,

Part Number 100005 (20 oz) or 100028 (48 oz).

• Do not use special additives.

• Choose a viscosity according to the table opposite.

Note: Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol

(shown at left) with “SJ/CF ENERGY CON-

SERVING” or higher ,is an acceptable oil atall

temperatures. Useof syntheticoil doesnot

alter required oil change intervals.

°F

-20 0 20 40 60 80 100

°C

-30 -20 -10 0 10 20 30 40

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

* CAUTION: Air cooled engines run hotter than

automotive engines. The use of non-synthetic

multi-viscosity oils (5W-30, 10W-30, etc.) in

temperatures above 40° F(4° C) will result in higher

than normal oil consumption. When using a

multi-viscosity oil, check oil level more frequently.

** CAUTION: SAE 30 oil, if used below 40° F(4° C), will

result in hard starting and possible engine bore

damage due to inadequate lubrication.

SAE Viscosity Grades

CHECKING AND ADDING OIL

• Check oil level before starting the engine.

• Check level daily, or after every eight (8) hours.

• Keep oil level at FULL.

• Do not overfill.

[1] Place engine level and clean around oil fill area.

[2] Remove oil fill cap.

[3] Add oil, if needed.

[4] Pour slowly. Fill to point of overflowing.

[5] Replace and tighten

oil fill cap.

OIL LEVELOIL LEVEL

Oil Fill

FUEL

TYPE OF FUEL TO USE

• Use clean, fresh, regular unleaded gasoline with a

minimum of 77 octane. Fresh fuel prevents gum from

forminginthefuelsystemo rone ssen tialcarb uretorparts.

Purchase fuel in quantity that can be used within 30 days.

• Do not use gasoline which contains Methanol.

• Do not mix oil with gasoline.

• For engine protection use Briggs & Stratton Gasoline

Additive available from your Authorized Briggs &

Stratton Dealer (P/N 5041 or single use pouch).

• This engine is certified to operate on gasoline. Exhaust

Emission Control System: EM (Engine Modifications).

CAUTION: Some fuels, called oxygenated or reformu-

lated gasoline, are gasoline blended with alcohols or

ethers.Excessiveamountsoftheseblendscandamage

the fuel system or cause performance problems. I f any

undesirable operating symptoms occur, use gasoline

with a lower percentage of alcohol or ether .

ADDING FUEL

WARNING

[1] Remove cap. Fill tank to

approximately 1/2 inch below

lowest portion of fill opening to

allow for fuel expansion. Be careful

not to overfill.

[2] Replace cap before starting.

Fuel Fill

• Fillfueltankoutdoorsorinwell-ventilatedarea,away

from sparks, open flames, pilot lights, heat, and

other ignition sources.

• If fuel spills, wait until it evaporates before starting

engine.

• Turn engine OFF and let engine cool at least 2

minutes before removing gas cap.

STARTING AND STOPPING

STARTING AND OPERATING TIPS

♦Store and fuel equipment in

level position.

♦Use fresh fuel. (See Fuel.)

♦Use correct type of oil for

expected starting tempera-

ture. (See Oil.)

♦Remove external equip-

ment/engine loads. (See

equipment operating

instructions.)

♦Periodically remove any de-

bris buildup from the ma-

chine (See Maintenance.)

♦After engine has started, let

it warm up several seconds

to several minutes, depend-

ing on outside temperature.

♦For maximum performance

and life, operate engine with

choke in RUN and throttle in

FAST.

WARNING

• Do not use pressurized

starting fluids.

• Vapors are flammable.

REWIND (MANUAL) STARTER

TO START ENGINE

[1] Check oil level (see p. 8).

[2] Move throttle to F AST. Operate engine with throttle in

F AST.

[3] Move choke control lever to CHOKE.

[4] Move stop switch to ON

(if equipped).

[5] When starting engine,pull cordslowly untilresistance

is felt, then pull rapidly.

[6] Allow engine to warm up.

Adjust Choke: Slowlyadjust towardRUNposition.W ait

until engine runs smoothly before each choke adjust-

ment.

WARNING

OIL LEVEL

OFF

Stop Switch

Throttle

Choke

TO STOP ENGINE

[1] Move throttle control to SLOW,

then to STOP (if equipped).

[2] Push stop switch

(if equipped) to OFF.

CAUTION: Do not stop engine

by moving choke control to

CHOKE. Backfire, fire or engine

damage could occur.

Stop Switch

OFF

Throttle

MAINTENANCE

Regular maintenance will improve the performance and

extend the life of the engine. See any Authorized Briggs &

Stratton Dealer for service. Use only genuine Briggs

Stratton parts. Other parts may not perform as

well,

may damage the engine, and may result in injury

. In

addition, use of other parts may void your warranty.

EMISSION CONTROL

Maintenance, replacement or repair of the emission

controldevicesand systemsmay beperformed byany

nonroad engine repair establishment or individual.

However , to obtain no charge repairs under the terms and

provisionsoftheBriggs&Strattonwarranty statement,any

serviceoremissioncontrolpart repair or replacementmust

be performed by a factory authorized dealer .

Follow the instructions and schedules indicated below.

Task

Perform task at hourly

or calendar interval,

whichever comes first.

Every 8 Hours

or Daily

25 Hours or

Every Season

50 Hours or

Every Season

100 Hours or

Every Season

100-300 Hours

Check Oil Level

✔

Change Oil

✔*

Change oil in gear

reduction (if equipped)

✔

Service air cleaner

pre-cleaner (if equipped)

✔**

Service air cleaner car-

tridge (if not equipped

with pre-cleaner)

✔**

Service air cleaner car-

tridge (if equipped with

pre-cleaner)

✔**

Inspect spark arrester

(if equipped)

✔

Replace spark plug

✔

Clean cooling system

✔**

Clean combustion

chamber

✔

* Changeoil afterfirst5to8hoursofuse,thenevery

50 hours or every season. Change oil every 25 hours

whenoperatingtheengineunderheavyloador inhigh

temperatures.

** Clean more often under dusty conditions or when

airbornedebrisispresent. Replace aircleanerparts,if

very dirty.

CAUTION: Used oil is a hazardous waste product.

Dispose of used oil properly. Do not discard with

householdwaste. Check withyour localauthorities,

service center, or dealer for safe disposal/recycling

facilities.

CHANGING OIL

Change oil after first 5 hours of use.

WARNING

Typical drain plugs

1/4” HEX

PIPE

OIL

DRAIN

PLUG

[1] Place engine level.

[2] Place engine level. Dis-

connect spark plug wire

and keep it away from

spark plug.

[3] With engine OFF but still warm remove oil drain

plug and drain oil into appropriate receptacle.

[4] Reinstall oil drain plug. Remove oil fill cap.

[5] Add about 2/3 quart (21 ounces; 0.6 liter) new oil.

Fill to point of overflowing.

[6] Replace oil fill cap.

OIL FILL

CAP

OIL LEVEL

MAINTENANCE

AIR CLEANER

CAUTION: Donotusepressurizedairorsolventsto

clean cartridge. Pressurized air can damage

cartridge; solvents will dissolve cartridge.

COVER

CARTRIDGE

BASE

To Remove

To Install

PUSH T ABS IN

WHILE PULLING

ON COVER TO

REMOVE

COVER

REMOVING AND RE-INSTALLING AIR CLEANER

[1] Push inthetabs locatedonthesides ofthe air cleaner

cover, while pulling cover off.

[2] Remove cartridge carefully to prevent debris from

entering carburetor.

[3] Re-install new air cleaner assembly in base.

[4] Replace cover by snapping tabs back into place.

Pre-cleaner

To clean pre-cleaner (if equipped), separate it from

cartridge and wash in liquid detergent and water. Air dry

thoroughly. Do not oil. Re-install dry pre-cleaner on clean

cartridge.

CAUTION: Donotusepressurizedairorsolventsto

clean cartridge. Pressurized air can damage

cartridge; solvents will dissolve cartridge.

SCREWS

COVER

CARTRIDGE

P/N 491588

OR 5043

PRE-CLEANER

P/N 491435

BASE

REMOVING AND RE-INSTALLING AIR CLEANER

[1] Loosen screws and remove cover.

[2] Remove pre-cleaner (if equipped) and cartridge

carefully to prevent debris from entering carburetor.

[3] Re-installclean(ornew)air cleanerassembly inbase.

[4] Replace cover and tighten screws.

MAINTENANCE

ENGINE AND ENGINE PARTS

We recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engine

and engine parts. Use only genuine Briggs & Stratton parts.

WARNING

If you perform any maintenance on the engine, first disconnect the spark plug wire

from the spark plug, and disconnect the battery at the negative terminal (electric

starter engines only) to prevent unintentional sparking. Unintentional sparking can

result in fire or electric shock. Unintentional start-up can result in entanglement,

traumatic amputation or laceration. Use only correct tools.

WARNING

• Do not strike the flywheel with a hammer or hard object because the flywheel may

later shatter during operation.

• Do not tamper with governor spring, links or other parts to increase engine speed.

Replacement parts for the

muffler must be the same and

installed in the same position

as theoriginal parts, otherwise

fire can occur.

If muffler is equipped with

spark arrestor screen, remove

screen for inspection. Replace

screen if damaged or plugged.

WARNING

MUFFLER

Note: In some areas,

locallawrequiresusing

resistor spark plug to

suppress ignition sig-

nals. If this engine was

originally equipped

with resistor spark

plug,usesame typefor

replacement.

.030” (0.76 mm)

WIRE GAGE

RESISTOR P/N 802592

STANDARD P/N 492167

Use only Briggs & Stratton Spark Tester (part

number 19368) to check for spark.

PLUG

COMBUSTION DEPOSITS

We recommend that after every 100-300 hours you have

an authorized Briggs & Stratton Service Dealer remove

combustion deposits from the cylinder, cylinder head, top

of piston, and around valves.

WARNING

Replacement parts for fuel

system (cap, hoses, tanks,

filters, etc.) must be the

same as original parts,

otherwise fire can occur.

FUEL SYSTEM

CLEAN OUT

DEBRIS AND CHAFF

IR COOLING S

STEM

It is recommended to clean the air cooling system

with blower housing removed every 100 hours.

MAINTENANCE

CLEANING DEBRIS

Daily or before every use, clean accumulated debris from

engine.Keeplinkage, springandcontrolsclean.Keeparea

around and behind muffler free of any combustible debris.

CAUTION: Do not use water to clean engine

parts. Water could contaminate fuel system.

Use a brush or dry cloth.

Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris.

WARNING

Finger Guard

Linka ge, Springs , Contr ols

Muffler, Spark Arrester

CLEAN

CHANGING OIL IN GEAR REDUCTION

(if equipped)

Change oil in gear reduction after every 100 hours of

operation.

[1] Todrainoil,loosen4gearcasecoverscrews an ddrain

oil into appropriate receptacle.

[2] After draining, torque 4 screws to 85 in-lbs.

[3] To refill, pour SAE 30oil into oil fill hole until it runs out

level check hole.

[4] Replace both oil plugs.

Note: Oilfiller plughasavent holeandmustbeinstalledon

top of gear case cover .

OIL FILLER PLUG

OIL LEVEL

PLUG

VENT HOLE

4 GEAR CASE

COVER SCREWS

SERVICE & STORAGE

SERVICE

See an Authorized Briggs & Stratton Service Dealer. Each

one carries astock of Genuine Briggs & Stratton Parts and

is equipped with special service tools. Trained mechanics

assure expert repair service on all Briggs & Stratton

engines. Only dealers advertising as “Authorized Briggs &

Stratton” arerequired tomeet Briggs & Strattonstandards.

When you purchase equipment powered by a

Br igg s & Stratton engine, you are assured of

highly skilled, reliable service at more than

30,000 Authorized Service Dealers

worldwide, including more than 5,000 Master

Service Technicians. Look for these signs

wherever Briggs&Strattonservice is offered.

You may locate your nearest Authorized Briggs & Stratton

Service Dealer in our dealer locator map on our web site

www.briggsandstratton.com or in the “Yellow Pages”

directory under “Engines, Gasoline” or “Gasoline

Engines,” or “Lawn Mowers” or similar category.

Note: W alking fingers logo and “Yellow Pages” are regis-

tered trademarks in various jurisdictions.



An illustrated shop manual includes

common specifications and detailed in-

formation covering adjustment, tune-up

and repair of Briggs & Stratton single

cylinder, L-head, 4 cycle engines. It is

available for purchase from an Autho-

rizedBriggs & StrattonService Dealeror

you can order it from the factory. Write:

Briggs & Stratton Corporation

Attn: Service Division

P. O. Box 1144

Milwaukee, WI 53201

Part No. 270962

PARTIAL LIST OF GENUINE BRIGGS &

STRATTON PARTS

BRIGGS & STRATTON

PART

PART NO.

Oval air cleaner cartridge 790166

Flat air cleaner cartridge 491588 -or- 5043

Flat air cleaner pre-cleaner 491435

Oil 100005 -or- 100028

Fuel Filter 298090 -or- 5018

Gas additive 5041

Resistor spark plug 802592

Standard spark plug 492167

Spark plug wrench 89838 -or- 5023

Spark tester 19368

Oil pump kit 5056

(uses standard electric drill to remove oil from enginequickly)

STORAGE

Engines stored over 30 days need special attention.

[1] To prevent gum from forming in fuel system or on

essential carburetor parts:

a) if fuel tank contains oxygenated or reformulated

gasoline (gasoline blended with an alcohol or an

ether), runengineuntilitstops from lack of fuel,orb)if

fuel tank contains gasoline, either run engine until it

stops from lack of fuel, or add a gasoline additive to the

gas in the tank. (See parts list. Single -- use pouches of

gas additive are available from your service dealer .) If

you use a gas additive, run the engine for several

minutes to circulate the additive through the carburetor .

Then, engine and fuel can be stored up to 24 months.

[2] While engine is still warm, change oil.

[3] Remove spark plug and pour about 1/2 oz. (15 ml) of

engine oil into cylinder. Replace spark plug andcrank

slowly to distribute oil.

[4] Clean engine of surface debris, chaff or grass.

WARNING

[5] Store in a clean, dry area.

Do not store in same area

as a stove, furnace, water

heater, or other appliance

that uses a pilot light or

has a device that can

create a spark.

Effective January 1, 2003 replaces all undated Warranties and all Warranties dated before January 1, 2003

BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.

Transportationcharges onpartssubmittedforrepairorreplacement underthiswarrantymustbeborneby purchaser.Thiswarrantyiseffectiveforthe

timeperiodsandsubjecttotheconditionsstatedbelow.Forwarrantyservice,findthenearestAuthorizedServiceDealerinourdealerlocatormap

at www.briggsandstratton.com

, or by calling 1-800-233-3723, or as listed i n the ‘Yellow Pages’.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A

PARTICULARPURPOSE, ARELIMITED TOONE YEARFROM PURCHASE, OR TOTHEEXTENTPERMITTEDBYLAWANY AND ALL IMPLIED

WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT

EXCLUSION IS PERMITTED BY LAW. Some states or countries donot allow limitations on how long an implied warranty lasts, and some states or

countries do notallow the exclusionor limitation ofincidental or consequentialdamages, sothe above limitationand exclusion may not applyto you.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state and country to country.

Vanguard

ELS

I/Cr

Industrial Plus

Intek

(Sleeve Bore)

Fource

Intek

(Kool Bore)

Power Built OHV

Quantumr

Quattro

Q45

Sprint

Classic

Commercial Use

2 years

90days1 year

Consumer Use

2 years

2years

90 days

1 year

OUR PRODUCT

WARRANTY PERIOD*

Etek

1 year

* Notethefollowingspecialwarrantyperiods:2yearsforClassic enginesintheEuropeanUnionandEasternEuropeancountries,forallconsumerproductsin

theEuropeanUnion,andforemissioncontrolsystemsonenginescertifiedbyEPAandCARB.5yearsforconsumeruse,90daysforcommercialuseofTouch-N-

Mow starter on Quantum and Intek engines. Engines used in competitive racing or on commercial or rental tracks are not warrantied.

The warrantyperiod begins on the date of purchase b y the first retail consumer or commercial end user, and continues for the period oftime statedin the table

above.“Consumer use” meanspersonal residentialhouseholduse by aretail consumer.“Commercial use” meansall otheruses, i ncluding usefor commercial,

income producing or rental purposes. Once an engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for pur-

poses of this warranty.

NOWARRANTYREGISTRATIONIS NECESSARYTOOBTAINWARRANTYONBRIGGS& STRATTONPRODUCTS. SAVE YOURPROOF OF PURCHASE

RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE

MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

Briggs & Stratton welcomes warranty repair and apologizes to

you for being inconvenienced. Any Authorized Service Dealer

may perform warranty repairs. Most warranty repairs are

handled routinely, but sometimes requests for warranty

service may not be appropriate. For example, warranty would

not apply if engine damage occurred because of misuse, lack

of routine maintenance, shipping, handling, warehousing or

improper installation. Similarly, warranty is void if the serial

number of the engine has been removed or the engine has

been altered or modified.

If a customer differs with the decision of the Service Dealer, an

investigation will be made to determine whether the warranty

applies. Ask theService Dealer tosubmit all supportingfacts to

his Distributor or the Factory for review. If the Distributor or the

Factory decides that the claim is justified, the customer will be

fully reimbursed for those items that are defective. To avoid

misunderstanding which might occur between the customer

and the Dealer, listed below are some of the causes of engine

failure that the warranty does not cover.

Normal wear:

Engines, like all mechanical devices, need periodic parts

service and replacement to perform well. Warranty will not

coverrepair when normaluse hasexhausted thelife ofa part or

an engine.

Improper maintenance:

The life of an engine depends upon the conditions under which

it operates, and the care it receives. Some applications, such

as tillers, pumps and rotary mowers, are very often used in

dusty or dirty conditions, which can cause what appears to be

premature wear. Such wear, when caused by dirt, dust, spark

plug cleaning grit, or other abrasive material that has entered

the engine because of improper maintenance, is not covered

by warranty.

This warranty covers engine related defective material

and/or workmanship only

, and not replacement or refund

of the equipment to which the engine may be mounted.

Nor doesthe warranty extend to repairs required because

of:

1. PROBLEMS CAUSED BY PARTS THAT ARE NOT

ORIGINAL BRIGGS & STRATTON PARTS.

2. Equipment controls or installations that prevent starting,

cause unsatisfactory engine performance, or shorten

engine life. (Contact equipment manufacturer.)

3. Leaking carburetors, clogged fuel pipes, stickingvalves,

or otherdamage, caused by using contaminated or stale

fuel. (Use clean, fresh, lead-free gasoline and Briggs &

Stratton Fuel Stabilizer, Part No. 5041.)

4. Parts which are scored or broken because an engine

was operated with insufficient or contaminated

lubricating oil, or an incorrect grade of lubricating oil

(check oil level daily or after every 8 hours of operation.

Refill when necessary and change at recommended

intervals.) OIL GARD may not shut down running

engine. Engine damage may occur if oil level is not

properly maintained. Read Operating & Maintenance

Instructions.

5. Repair or adjustment of associated parts or assemblies

such as clutches, transmissions, remote controls, etc.,

which are not manufactured by Briggs & Stratton.

6. Damage or wear to parts caused by dirt, which entered

the engine because of improper air cleaner

maintenance, re-assembly, or use of a non-original air

cleaner element or cartridge. (At recommended

intervals, clean and re-oil the Oil-Foam element or the

foam pre-cleaner, and replace the cartridge.) Read

Operating & Maintenance Instructions.

7. Parts damaged by over-speeding, or overheating

caused by grass, debris, or dirt, which plugs or clogs the

cooling fins, or flywheel area, or damage caused by

operating the engine in a confined area without sufficient

ventilation. (Cleanfins on the cylinder,cylinder headand

flywheel at recommended intervals.) Read Operating &

Maintenance Instructions.

8. Engine or equipment parts broken by excessive

vibration caused by a loose engine mounting, loose

cutter blades, unbalanced blades or loose or

unbalanced impellers, improper attachment of

equipment to engine crankshaft, over-speeding or other

abuse in operation.

9. A bent or broken crankshaft, caused by striking a solid

object with the cutter blade of a rotary lawn mower, or

excessive v-belt tightness.

10. Routine tune-up or adjustment of the engine.

11. Engine or engine component failure, i.e., combustion

chamber, valves, valve seats, valve guides, or burned

starter motor windings, caused by the use of alternate

fuels such as, liquified petroleum, natural gas, altered

gasolines, etc.

Wa rranty is available only through service dealers which

have been authorized by Briggs & Stratton Corporation.

your nearest Authorized Service Dealer is listed in the

“Yellow Pages” of your telephone directory under

“Engines, Gasoline” or “Gasoline Engines,” “Lawn

Mowers,” or similar category.

ABOUT YOUR ENGINE WARRANTY

Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)

and the United States Environmental Protection Agency (U.S. EPA)

Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations)

EMISSIONCONTROLWARRANTYCOVERAGEISAPPLICABLETOCERTIFIEDENGINESPURCHASEDINCALIFORNIAIN1995ANDTHERE-

AFTER,WHICHAREUSEDINCALIFORNIA,ANDTOCERTIFIEDMODELYEAR1997ANDLATERENGINESWHICHAREPURCHASEDAND

USED ELSEWHERE IN THE UNITED STATES (AND AFTER JANUARY 1, 2001 IN CANADA).

California and United States Emission Control Defects Warranty Statement

The CaliforniaAir Resources Board(CARB), U.S.

EPAand B&Sare pleasedtoexplain theEmission

Control System Warranty on your model year

2002 and later small off-road engine (SORE). In

California,newsmall of f-roadengines mustbe de-

signed, built and equipped to meet the State’s

stringent anti-smog standards.

Elsewhere in the United States, new non-road,

spark-ignition engines certified for model year

1997 and later must meet similar standards set

forthbytheU.S.EPA.B&Smustwarranttheemis-

sion control system on your enginefor the periods

of time listed below , provided there has been no

abuse, neglect or improper maintenance of your

small off-road engine.

Your emission control system includes parts

such as thecarburetor, aircleaner, ignition sys-

tem, muffler and catalytic converter. Also in-

cluded may be connectors and other emission

related assemblies.

Where a warrantable condition exists, B&S will

repair your small off-road engine at no cost to

you including diagnosis, parts and labor.

Briggs & Stratton Emission Control D efects Warranty Coverage

Small off-road engines are warranted relative to emission control parts defects for a period of two years, subject to provisions set forth below. If any

covered part on your engine is defective, the part will be repaired or replaced by B&S.

Owner’s Warranty Responsibilities

As the small off-road engine owner, you are re-

sponsible for the performance of the required

maintenancelistedin yourOperatingand Main-

tenance Instructions. B&S recommends that

you retain all your receipts covering mainte-

nance on your small off-road engine, but B&S

cannot deny warranty solely for the lack of re-

ceipts or for your failure to ensure the perfor-

mance of all scheduled maintenance.

As the small off-road engine owner, you should

howeverbe awarethatB&S maydenyyou war-

rantycoverageif yoursmall off-roadengineora

part has failed due to abuse, neglect, improper

maintenance or unapproved modifications.

You are responsible for presenting your small

off-road engine to an Authorized B&S Service

Dealer as soon as a problem exists.

The undisputed warranty repairs should be

completed in a reasonable amount of time, not

to exceed 30 days.

If you have any questions regarding your war-

rantyrightsandresponsibilities,youshouldcon-

tact a B&S Service R epresentative at

1-414-259-5262.

The emission warranty is a defects warranty.

Defects are judged on normal engine perfor-

mance. The warranty isnot related to an in-use

emission test.

Briggs & Stratton Emission Control D efects Warranty Provisions

Thefollowingarespecificprovisionsrelative to yourEmissionControlDefects Warranty Coverage.Itis inaddition to theB&S enginewarranty fornon-

regulated engines found in the Operating and Maintenance Instructions.

1. Warranted Parts

Coverageunder thiswarranty extendsonly

to the parts listed below (the emission con-

trol systemsparts) to theextent theseparts

were present on the engine purchased.

a. Fuel Metering System

• Cold start enrichment system

• Carburetor and internal parts

• Fuel Pump

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system, Pulse valve

e. Miscellaneous Items

• Vacuum, temperature, position,

time sensitive valves

and switches

• Connectors and assemblies

2. Length of Coverage

B&S warrants to the initial owner and each

subsequent purchaser that the Warranted

Parts shall be free from defects in materials

and workmanship which caused the failure

of the Warranted Parts for a period of two

yearsfromthedatetheengineisdeliveredto

a retail purchaser.

3. No Charge

Repair or replacement of any Warranted

Part will be performed at no charge to the

owner, including diagnostic labor which

leadstothe determinationthat aWarranted

Part is defective, if the diagnostic work is

performed at an Authorized B&S Service

Dealer. For emissions warranty service

contact your nearest Authorized B&S Ser-

vice Dealer as listed in the “Yellow Pages”

under “Engines, Gasoline,” “Gasoline En-

gines,”“Lawn Mowers,”or similarcategory.

4. Claims and Coverage Exclusions

Warrantyclaimsshallbefiledinaccordance

with theprovisions ofthe B&S EngineWar-

rantyPolicy.Warrantycoverageshallbeex-

cludedforfailuresofWarrantedPartswhich

are not original B&S parts or because of

abuse,neglectorimpropermaintenanceas

setforthintheB&SEngineWarrantyPolicy.

B&S is not liable to cover failures of War-

ranted Parts caused by the use of add-on,

non-original, or modified parts.

5. Maintenance

Any W arranted Part which is not scheduled

for replacement as required maintenance or

which is scheduled only for regular inspec-

tion to the effect of“repair or replace asnec-

essary” shall be warranted as to defects for

the warranty period. Any Warranted Part

which is scheduled for replacement as re-

quiredmaintenanceshall bewarrantedasto

defects only for the period of time up to the

firstscheduledreplacementforthatpart.Any

replacement partthat isequivalent in perfor-

manceanddurabilitymaybeusedintheper-

formance of any maintenance or repairs.

The owner is responsible for the perfor-

mance of all required maintenance, as de-

finedintheB&SOperatingandMaintenance

Instructions.

6. Consequential Coverage

Coveragehereundershallextendtothefail-

ure of any engine components caused by

the failure of any Warranted Part stillunder

warranty.

Briggs & Stratton Engines Are Made Under One Or More Of The Following Patents: Design D-247,177 (Other Patents Pending)

6,325,036

6,284,123

6,260,529

6,230,678

6,202,616

6,116,212

6,077,063

6,064,027

6,014,808

5,894,715

5,852,951

5,823,153

5,819,513

5,813,384

5,765,713

5,645,025

5,642,701

5,619,845

5,606,948

5,606,851

5,548,955

5,546,901

5,503,125

5,501,203

5,497,679

5,320,795

5,271,363

5,269,713

5,265,700

5,243,878

5,235,943

5,197,425

5,197,422

5,191,864

5,188,069

5,186,142

5,138,996

5,086,890

5,070,829

5,058,544

5,040,644

5,009,208

4,996,956

4,977,879

4,971,219

4,895,119

4,819,593

4,719,682

4,633,556

4,630,498

4,522,080

4,520,288

4,512,499

4,453,507

4,430,984 DES. 308,871

DES. 308,872

DES. 309,457

DES. 356,951

DES. 361,771

DES. 375,963

(Cette page ne s’applique que pour le Canada et les Etats--Unis)

La Corporation Briggs & Stratton (B&S), le California Air Resources Board (CARB)

et le Bureau de protection environnementale des Etats- Unis (US EPA)

Garantie sur le système d’échappement (Garantie contre les défectuosités, droits et obligations du propriétaire)

LA GARANTIE SUR LE SYSTÈME D’ÉCHAPPEMENT EST APPLICABLE SUR LES MOTEURS

CERTIFIÉSACHETÉS EN CALIFORNIEEN 1995 ETLESANNÉES SUIVANTES ETQUISONT UTI-

LISÉS EN CALIFORNIE, AINSI QU’AUX MODÈLES CERTIFIÉS DE 1997 ET LES ANNÉES SUI-

VANTES QUI ONT ÉTÉ ACHETÉS ET UTILISÉS AILLEURS AUX ET ATS--UNIS (ET APRÉS LE 1ER

JANVIER 2001 AU CANADA).

Déclaration de garantie sur le système d’échappement pour la Californie, les Etats- Unis

Le California Air Resources Board (CARB), le Bureau américain de protection environnementale

(U.S. EPA) et B& S sont heureux d’expliquer la garantie sur le système d’échappement des petits

moteurs hors--route de votre modèle 2000 et des années ultérieures (SORE). En Californie, les

nouveaux petits moteurs horsroutedoiventêtreconçus, construits et équipés pour rencontrerles

standards rigoureux d’antipollution. Ailleurs aux Etats--Unis, les nouveaux moteurs hors route à

bougie d’allumagecertifiés pour lesmodèles de 1997et plus, doivent rencontrerdes normes simi-

laires mises de l’avant par le U.S. EPA. Briggs & Stratton garantit le système de contrôle d’échap-

pement de votre moteur pour la période de temps mentionnée ci--contre, sauf s’il a fait l’objet

d’abus, de négligence ou d’un entretien inapproprié.

Votresystème decontrôled’échappement comprenddespièces tellesquelecarburateur,le filtreà

air, le système d’ignition, le silencieuxetleconvertisseur catalytique. Il peut aussi comprendre les

connecteurs et autres pièces reliées à l’émission.

Lorsqu’ily aconditionà garantie,B&Sréparera gratuitementvotrepetit moteurhors--routeincluant

le diagnostic, les pièces et la main d’œuvre.

Couverture de garantie Briggs & Stratton contre toute défectuosité du système de contrôle d’échappement

Lespetitsmoteurshors routesontgarantiscontreladéfectuosité despiècesdusystèmedecontrô-

led’échappementpour unepériode de2 ans,sujetteauxconditionsstipuléesci--contre.Sin’impor-

te quelle pièce de votre moteur couverte par cette garantie est défectueuse, elle sera réparée ou

remplacée par B&S.

Responsabilités du propriétaire

Entantque propriétaired’un petitmoteur horsroute,vousêtesresponsabledeveilleràl’exécution

de l’entretienrequis tel questipulédans votre manueld’opérationet d’entretien. B&S vousrecom-

mande deconserver tous lesreçuscouvrant les travauxd’entretien de votrepetitmoteur hors rou-

te, mais B&S ne peut refuser la garantie enraisond’absencedereçus ou pour défaut d’avoir suivi

tout l’échéancier du programme d’entretien.

Entant quepropriétaired’un petitmoteurhors route,vousdevez êtreinforméque B&Speutrefuser

d’honorercettegarantiesiladéfectuositédevotre moteuroud’unepartiedevotremoteur estdueà

un emploi abusif, une négligence, un entretien incorrect ou une modification non approuvée.

Vous avez la responsabilité d’apporter votre petit moteur hors route à un détaillant autorisé B&S

aussitôtquesurvientun problème.Lesréparationssousgarantiedoiventêtre complétéesdans un

délai raisonnable ne devant pas excéder 30 jours.

Si vous avez des questions relativement à votre garantie, vos droits et responsabilités, veuillez

communiquer avec un représentant de service B&S au numéro 1--414--259--5262.

La garantie dusystèmed’échappement est une garantie contre lesdéfectuosités. Les défectuosi-

tés sont jugées en fonction d’une utilisation normale du moteur. La garantie n’est pas reliée à un

test d’échappement effectué à l’intérieur.

Dispositions de la garantie du système d’échappement Briggs & Stratton

Ce qui suit concerne les dispositions spécifiques relativement à votre garantie sur le système de contrôle d’échappement. C’est une addition à la garantie B&S pour les moteurs non réglementés contenue

dans le manuel d’entretien et d’utilisation.

1. Pièces sous garantie

La couverture de cette garantie ne s’applique que sur les pièces listées ci--contre (les parties

dusystèmede contrôled’échappement) danslamesure oùcespiècesétaientprésentessurle

moteur au moment de l’achat.

a. Système de dosage du carburant

• Système d’enrichissement de démarrage à froid

• Carburateur et parties internes

• Pompeàessence

b. Système d’induction d’air

• Filtre à air

• Tubulure d’admission

c. Système d’ignition

• Bougies d’allumage

• Système d’allumage électromagnétique

d. Système catalyseur

• Convertisseur catalytique

• Collecteur d’échappement

• Système d’injection d’air ou à pulsion

e. Autres pièces utilisées dans les systèmes ci--haut mentionnés

• Soupapes et interrupteurs de dépression, de température, de position.

• Connecteurs et assemblages.

2. Duréedelacouverture

B&S garantit le propriétaire initial et tous les acheteurs subséquents que les pièces sous ga-

rantiesontexemptes device dematière oudefabricationqui pourraientcauserdesdéfectuosi-

tés despiècessous garantie pour une périodede deux ans à partirdela date àlaquellele mo-

teur a été livré à l’acheteur.

3. Aucuns Frais

La réparation ou le remplacement de toute pièce sous garantie sera effectuée sans aucuns

frais pour le propriétaire, incluant les frais de maind’œuvrepourle diagnostic afin de détermi-

ner si la pièce sous garantie est défectueuse, conditionnel à ce que le diagnostic soit effectué

chezun détaillantautoriséB&S.Pourla garantierelative ausystème d’échappement,commu-

niquez avec le détaillant autorisé B&S le plus proche tel que listé dans les pages jaunes de

votre localité sous la rubrique moteur à essence, tondeuse ou autre catégorie similaire.

4. Réclamations et exclusions de la couverture.

Les réclamations de garantie doivent être complétées en accord avec les dispositions de la

politique de garantie B&S. La garantie ne couvre pas les défectuosités de pièces qui ne sont

pas despièces d’origine B&Sou dans lecas d’abus, négligenceoud’un entretieninapproprié.

La garantie B&S ne couvre pas les défectuosités de pièces sous garantie qui ont fait l’objet

d’ajouts, ont été modifiées ou de pièces qui ne sont pas des pièces B&S d’origine.

5. Entretien

Toute pièce sousgarantiequi n’est pas remplacée aumomentrequis selon le manuel d’entre-

tien ou qui est planifiée seulement pour une inspection régulière souslamention« réparer ou

remplacer si nécessaire » est garantie contre toute défectuosité pour la période de garantie.

Toute pièce sous garantie qui est planifiée pour un remplacement tel que requis dans l’entre-

tien estgarantie contre toute défectuositéseulement pour la périodedetemps qui vajusqu’au

premier remplacement prévu pour cette pièce. Toute pièce de remplacement équivalente en

performance etdurabilité peut être utiliséepourl’entretien ou la réparation.Le propriétaire est

responsable de l’exécution de tout entretien requis tel que défini dans le manuel d’instruction

B&S sur l’entretien et la réparation.

6. Couverture indirecte

La couverture ci--contre s’étend à toute défectuosité des composantes du moteur causée par

ladéfectuositéde n’importequelle piècecouverte parla garantieet dont lagarantie estencore

en vigueur.

À compter du 1

juillet 2000, surveillez la période de conformité d’émission sur les étiquettes

Après le 1

juillet 2000, certains moteurs B&S seront certifiés conformes aux normes environnementales d’émission standard du United States Environmental Protection Agency (US EPA) Phase 2. Pour les

moteurs certifiés pour la Phase 2, la période de conformité d’émission mentionnée sur les étiquettes indique le nombre d’heures d’utilisation pour lequel le moteur rencontre les normes fédérales. Pour les

moteurs de force moindre que 225 cc, la catégorie C = 125 heures, B = 250 heures et A = 500 heures. Pour les moteurs de 225 cc et plus, la catégorie C = 250 heures, B = 500 heures et A = 1000 heures.

Le remplacement du moteur portant le modèle de série 185400 est 297 cc. Le remplacement du moteur portant le modèle de série 235400 et 245400 est 392 cc.

Ceci est une représentation des étiquettes d’émission

que vous retrouverez sur les moteurs certifiés :

CE MOTEUR EST CONFORME AUX NORMES

ANTIPOLLUTION 2000 -- 2001 DE CALIFORNIE

POUR LES PETITSMOTEURS HORS ROUTE ET

AUX NORMES ENVIRONNEMENTALES

AMÉRICAINES (EPAPHASE 2) POUR LES

PETITS MOTEURS HORS ROUTE. CONSULTEZ

LE MANUEL DU PROPRIÉTAIRE POUR LES

SPÉCIFICATIONS, L’ENTRETIEN ET LES

AJUSTEMENTS. CONFORMEÀ LA PÉRIODE

D’ÉMISSION EPA : CATÉGORIE : C