Aiwa cdcx 504mp Le manuel du propriétaire

Marque: Aiwa

Modèle: cdcx 504mp

Catégorie: Récepteurs multimédia de voiture

Taper: Le manuel du propriétaire

Ce manuel convient également à

CDC-X504MP

Operating Instructions...........................................................................

Mode d’emploi................................................................................................................

Manual de instrucciones......................................................................................

3-263-367-11(2)

CDC-X504MP

POR FAVOR LEA DETALLADAMENTE ESTE MANUAL DE

INSTRUCCIONES ANTES DE CONECTAR Y OPERAR ESTE EQUIPO.

RECUERDE QUE UN MAL USO DE SU APARATO PODAÍA ANULAR

LA GARANTÍA.

FM/AM Compact Disc Player

AUTOESTEREO PARA DISCO

COMPACTO

For assistance and information

visit us on the internet at

www.us.aiwa.com

call toll free 1-800-BUY-AIWA

(United States only)

If you have any questions or problems concerning

your unit that are not covered in this manual,

please consult your nearest Sony dealer.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the lenses and

display of the unit. Should this occur, the unit will

not operate properly. In such a case, remove the

disc and wait for about an hour until the moisture

has evaporated.

To maintain high sound quality

Be careful not to splash juice or other soft drinks

onto the unit or discs.

For installation and connections, see the

supplied installation/connections manual.

Notes on discs

•To keep a disc clean, do not touch its surface.

Handle the disc by its edge.

•Keep your discs in their cases or disc magazines

when not in use.

•Do not subject discs to heat/high temperature.

Avoid leaving them in parked cars or on

dashboards/rear trays.

•Do not attach labels, or use discs with sticky ink/

residue. Such discs may stop spinning when

used, causing a malfunction, or may ruin the

disc.

•Do not use any discs with labels or stickers

attached.

The following malfunctions may result from

using such discs:

Warning

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user

is encouraged to try to correct the interference

by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on

circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/

TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

CAUTION

The use of optical instruments with this

product will increase eye hazard.

Owner’s Record

The model and serial numbers are located on the

bottom of the unit.

Record these numbers in the space provided

below.

Refer to these numbers whenever you call upon

your Sony dealer regarding this product.

Model No.CDC-X504MP

Serial No.____________________________________

PRECAUTIONS

•If your car has been parked in direct sunlight,

allow the unit to cool off before operating it.

•Power antenna will extend automatically while

the unit is operating.

– Inability to eject a disc (due to a label or sticker

peeling off and jamming the eject mechanism).

– Inability to read audio data correctly (e.g.,

playback skipping, or no playback) due to heat

shrinking of a sticker or label causing a disc to

warp.

•Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do

not use such discs.

•You cannot play 8 cm (3 in) CDs.

•Before playing, clean the

discs with a commercially

available cleaning cloth.

Wipe each disc from the

center out. Do not use

solvents such as benzine,

thinner, commercially

available cleaners, or

antistatic spray intended for

analog discs.

Music discs encoded with copyright protection

This product is designed to play back discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with

companies. Please be aware that among those

discs, there are some that do not conform to the

CD standard and may not be playable by this

product.

Notes on CD-Rs (recordable CDs)/CD-

RWs (rewritable CDs)

This unit can play the following discs:

Type of discs Label on the disc

Audio CD

MP3 files

•Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the condition

of the disc) may not play on this unit.

•You cannot play a CD-R/CD-RW that is not

finalized*.

•You can play MP3 files recorded on CD-ROMs,

CD-Rs, and CD-RWs.

•A CD-R/CD-RW to which a session can be added

can be played.

*A process necessary for a recorded CD-R or CD-

RW disc to be played on the audio CD player.

TABLE OF CONTENTS

GETTING STARTED

Resetting the unit................................................. 4

DEMO (demonstration) mode ........................... 4

Theft protection................................................... 4

BASIC OPERATION, AUDIO AND CLOCK

ADJUSTMENT

Turning the unit on.............................................. 5

Setting the clock ................................................... 5

Adjusting sound .................................................. 5

RADIO OPERATION

Storing stations automatically .......................... 7

Receiving the stored stations ............................ 7

Storing stations manually................................... 7

CD PLAYER OPERATION

Playing a disc ....................................................... 8

Reading the display............................................. 9

OTHER FUNCTIONS

Using auxiliary equipment .............................. 10

Various settings .................................................. 10

CARD REMOTE CONTROL

Names of parts ................................................... 11

Preparations ....................................................... 11

Replacing the battery ........................................ 11

TROUBLESHOOTING

General ................................................................ 12

Radio reception .................................................. 12

CD play ............................................................... 13

ERROR DISPLAYS/MESSAGES

Error displays ..................................................... 13

Messages ............................................................. 13

ADDITIONAL INFORMATION

About MP3 files ................................................. 14

Maintenance ....................................................... 16

Removing the unit ............................................. 16

Specifications...................................................... 17

GETTING STARTED

Note

Some buttons on the unit are assigned two or more

functions. For detailed descriptions, refer to the

related pages.

Resetting the unit

Before operating the unit for the first time, or after

replacing the car battery or changing the

connections, you must reset the unit.

Remove the front panel and press the reset button

with a pointed object, such as a ballpoint pen.

Front panel detached

Reset button

Note

Pressing the reset button will erase the clock and

some memorized functions.

DEMO (demonstration) mode

The unit has an extra display (DEMO) mode which

demonstrates the illumination modes of the unit.

When you deactivate the unit by pressing (OFF),

the clock is displayed for about 10 seconds, then

the unit switches to DEMO mode.

To cancel DEMO mode

1 While in DEMO mode, press and hold

(PUSH-MENU) until “SET” appears on the

display.

2 Press (SEEK) (+) or (SEEK) (–) to select

“DEMO.”

3 Turn (PUSH-MENU) to select “DEMO OFF.”

To resume DEMO mode, repeat the above and

select “DEMO ON” at step 2.

Theft protection

Take the front panel with you when leaving the

car, and keep it in the supplied carrying case.

Caution alarm

If you turn off the ignition switch to the OFF

position without removing the front panel, the

caution alarm will beep for a few seconds.

If you connect an optional amplifier and do not use

the built-in amplifier, the beep tone will be

deactivated.

To detach the front panel

1 Press Z to remove the disc.

2 Press (OFF)*.

3 Press , then pull it off towards you. (Hold

the panel with one hand to prevent

accidentally dropping it.)

(OFF)

* If your car has no ACC position on the ignition

switch, be sure to turn the unit off by pressing

(OFF) until the display disappears to avoid car

battery drain.

To attach the front panel

1 Engage the right side of the front panel to

the right catch on the unit.

2 Push the panel forward until it locks.

Be sure not to press any buttons and the

display window.

Notes

•If you detach the panel while the unit is still

turned on, the power will turn off automatically

to prevent the speakers from being damaged.

•Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in a

parked car or on a dashboard/rear tray.

•Do not put anything on the inner surface of the

front panel.

BASIC OPERATION, AUDIO

AND CLOCK ADJUSTMENT

(OFF)

(PUSH-MENU)

(SEEK)(+)/(SEEK)(–)

(SOURCE)

(H-BASS),(EQ),

(DSPL),(ATT)

Turning the unit on

Press (SOURCE) on the front panel.

The unit also turns on when you insert a disc.

To deactivate the unit

Press (OFF).

The clock appears. After about 10 seconds, the unit

switches to DEMO mode (page 4).

To turn the unit off

Press and hold (OFF) until everything on the

display clears.

This operation is required to avoid car battery

drain, if your car has no ACC position on the

ignition switch.

Setting the clock

The clock uses a 12-hour digital indication.

1 Press and hold (DSPL) until the clock

appears.

2 Turn (PUSH-MENU) to set the hour.

3 Press (DSPL).

4 Turn (PUSH-MENU) to set the minute.

5 Press (DSPL).

To display the clock

Press (DSPL).

To return to the former display, press (DSPL)

again.

Adjusting sound

To adjust the volume

Turn (PUSH-MENU).

“VOL (volume)” appears on the display.

To attenuate the sound

Press (ATT).

“ATT•ON” appears on the display.

To restore the previous volume level, press (ATT)

again.

To adjust sound stage (DSSA*)

You can adjust sound stage and tone balance to

best serve a particular seat in the car.

* DSSA : abbreviation of “Drivers Sound Stage

Adjustment”

1 Press (PUSH-MENU).

2 Press (SEEK) (+) or (SEEK) (–) to select

“DSSA.”

3 Turn (PUSH-MENU) to select “L” (for the front

left seat), “R” (for the front right seat), or

“OFF.”

To adjust DSSA manually, press (PUSH-MENU)

after step 3 above, then press (SEEK) (+) or

(SEEK) (–) to select “BAL” or “FAD,” and turn

(PUSH-MENU) to adjust it.

To adjust the sound characteristics

You can adjust the balance, fader, low pass filter

and subwoofer volume.

1 Press (PUSH-MENU).

2 Press (SEEK) (+) or (SEEK) (–) to select

“BAL,” “FAD,” “LPF” or “SUB.”

Each time you press (SEEK) (+), the item

changes as follows:

LOW

t MID

t HI

BAL (balance; left-right) t

FAD (fader; front-rear) t

DSSA t

LPF (low pass filter)

*2*3

SUB (subwoofer volume)

*2*4

When EQ is activated (page 6)

When “SUB” is selected (page 10)

The cut off frequency is adjustable to 78 Hz,

125 Hz or OFF.

The volume level is adjustable between –10

and +10, or to ATT (attenuated).

3 Turn (PUSH-MENU) to adjust the selected

item.

To reinforce the bass sound

(H-BASS)

Press (H-BASS).

Each time you press (H-BASS), the H-BASS mode

is turned on and off.

Note

The H-BASS adjustment does not affect the signal

output from the AUDIO OUT REAR connectors on

the rear panel at the “SUB” (sub-woofer) position.

To set the equalizer (EQ)

You can select an equalizer curve for 7 music types

(HIP-HOP, VOCAL, CLUB, JAZZ, POPS, ROCK,

CUSTOM).

You can store a different equalizer setting for each

source.

To select the equalizer curve

1 Press (SOURCE) to select a source (TUNER,

CD or AUX).

2 Press (EQ) repeatedly to select the desired

equalizer curve.

To cancel the equalizing effect, select “OFF.”

To adjust the equalizer curve

You can adjust and store the equalizer settings for

different tone ranges.

1 Follow the steps 1 and 2 above.

2 Press (PUSH-MENU).

3 Press (SEEK) (+) or (SEEK) (–) to select the

desired tone range; “LOW,” “MID,” or “HI.”

4 Turn (PUSH-MENU) to adjust to the desired

volume level.

The volume level is adjustable from –10 to +10

dB by 1 dB steps.

5 Repeat steps 2 to 4 to adjust the equalizer

curve.

Note

When EQ is set to “OFF,” you cannot adjust the

equalizer curve settings.

To restore the factory settings

You can restore the factory settings for the

equalizer curve settings while adjusting them.

During adjustment, press and hold

(PUSH-MENU) until the equalizer type (such as

HIP-HOP) appears on the display.

RADIO OPERATION

The unit can store up to 6 stations per band (FM1,

FM2, FM3, AM1 and AM2).

Caution

When tuning in to stations while driving, use Best

Tuning Memory to prevent accidents.

(SEEK)(+)/(SEEK)(–)

(SOURCE)

(BTM SENS)

(MODE)

Storing stations automatically

– Best Tuning Memory (BTM)

1 Press (SOURCE) repeatedly to select the

radio.

2 Press (MODE) repeatedly to select the band.

3 Press and hold (BTM SENS) until “BTM”

flashes on the display.

The unit stores stations in the order of their

frequencies on the number buttons.

A beep tone will be heard when the setting is

stored.

Notes

•If only a few stations can be received due to weak

signals, some number buttons will remain their

former settings.

•When a number is indicated on the display, the

unit starts storing stations from the one currently

displayed.

Receiving the stored stations

1 Press (SOURCE) repeatedly to select the

radio.

2 Press (MODE) repeatedly to select the band.

3 Press the number button ((1) to (6)) on

which the desired station is stored.

Automatic tuning

If preset tuning does not work, try the automatic

tuning.

Press (SEEK) (+) or (SEEK) (–) to search for the

station.

Scanning stops when the unit receives a station.

Repeat the operation until the desired station is

received.

If the automatic tuning stops too frequently

Press (BTM SENS) repeatedly until “LOCAL•ON”

appears on the display.

The “LCL” indicator is displayed.

Only the stations with relatively strong signals will

be tuned in (local seek mode).

To cancel the local seek mode, press (BTM SENS)

once or twice so that the “LCL” indicator

disappears.

If you know the frequency of the station

(manual tuning)

Press and hold (SEEK) (+) or (SEEK) (–) to locate

the approximate frequency.

Then press (SEEK) (+) or (SEEK) (–) repeatedly to

fine adjust to the desired frequency.

Monaural mode

If FM stereo reception is poor, receive the station in

monaural mode.

During radio reception, press (BTM SENS)

repeatedly until “MONO ON” appears on the

display.

The “MONO” indicator is displayed.

To return to normal radio reception, press

(BTM SENS) again.

Storing stations manually

You can store only the desired stations on any

chosen number buttons.

1 Press (SOURCE) repeatedly to select the

radio.

2 Press (MODE) repeatedly to select the band.

3 Press (SEEK) (+) or (SEEK) (–) to tune in to

the desired station.

4 Press and hold the desired number button

((1) to (6)) until “MEM” appears.

Frequency

Button number

Band

Number buttons

CD PLAYER OPERATION

In addition to ordinary CD play, you can enjoy the

unit’s following features:

•MP3 files

can be played.

•CD-R/CD-RW which can have a session added

can be played.

•CD TEXT information is displayed when a CD

TEXT disc

is played.

For more information about MP3 files, see

“About MP3 files” on page 14.

A CD TEXT disc is an audio CD that includes

information such as the disc name, artist name,

and track names. This information is recorded on

the disc.

Playing a disc

(OFF)

(PUSH-MENU)

(SEEK)(+)/(SEEK)(–)

(SOURCE)

(DSPL)

(6)(ALBUM+)

(5)(ALBUM–)

(SHUF)

(REP)

Insert a disc with the label side facing up.

“CD” appears on the display, and play starts.

If a disc is already inserted, press (SOURCE)

repeatedly until “CD” appears to start play.

In normal play, when the last track finishes, the

unit returns to the first track and continues to play.

To Press

Stop play Z or (OFF)

Eject the disc Z

Skip tracks (SEEK) (+)/(SEEK) (–)

(./>)

(once for each track)

Fast-forward/reverse (SEEK) (+)/(SEEK) (–)

(m/M)

(Press and hold to

desired point.)

Skip albums* (5) (ALBUM –) or

(6) (ALBUM +)

(Press and hold to

desired album.)

*Available only when an MP3 file is played.

Notes

•Depending on the condition of the disc, it may

not play back.

•A CD-R or CD-RW may take some time to start

playing, but this is not a malfunction.

•While the first/last track is playing, if (SEEK) (–)

or (SEEK) (+) is pressed, playback skips to the

last/first track.

•If you play a high-bit rate MP3 file such as

320 kbps, sound may be intermittent.

Repeat and shuffle play

You can select:

•REP•TRACK – to repeat the current track.

•REP•ALBM* – to repeat the tracks in the current

album.

•SHUF•ALBM* – to play the tracks in the current

album in random order.

•SHUF•DISC – to play all tracks in the disc in

random order.

*Available only when an MP3 file is played.

During play, press (REP) or (SHUF) repeatedly

until the desired repeat or shuffle mode

appears on the display.

To return to normal play, select “REP•OFF” or

“SHUF•OFF.”

Note

During shuffle play, pressing . allows you to

skip only to the beginning of the current track, not

to the previous track.

Reading the display

When the disc/album/track changes, any

prerecorded title

of the new disc/album/track is

displayed.

If the Auto Scroll mode is turned on, names

exceeding 8 characters will be scrolled.

There are following displayable items:

•Track number/elapsed playing time

•Disc name

/artist name

•Album name

•Track name

*1*3

•ID3 tag

•Clock

To Press

Switch display item (DSPL)

“NO NAME” is displayed when there is no

prerecorded name to display.

Only for CD TEXT discs with the artist name.

Only for MP3 files.

Only track name/artist name/album name in

ID3 tag is displayed.

“NO ID3” is displayed when there is no ID3 tag

to display.

Notes

•Some characters cannot be displayed.

•For some CD TEXT discs with very many

characters, information may not scroll.

•This unit cannot display the artist name for each

track of a CD TEXT disc.

To turn on/off the Auto Scroll mode

1 Press and hold (PUSH-MENU) until “SET”

appears on the display.

2 Press (SEEK) (+) or (SEEK) (–) to select

“A.SCRL.”

3 Turn (PUSH-MENU) to select “ON” or “OFF.”

Notes on MP3

•ID3 tag applies to version 1.0, 1.1, 2.2, 2.3 and 2.4.

•Some characters cannot be displayed. Characters

and signs which cannot be displayed appear as

“*.”

The muximum number of characters for album

(folder) name/track (file) names that can be

displayed is 64 each. ID3 tag is up to 30

characters (1.0, 1.1, 2.2 and 2.3) or 126 characters

(2.4).

•In the following cases, elapsed playing time may

not be displayed accurately.

– when an MP3 file of VBR (variable bit rate) is

played.

– during fast-forward/reverse.

OTHER FUNCTIONS

(PUSH-MENU)

(SEEK)(+)/(SEEK)(–)

(SOURCE)

AUX

Using auxiliary equipment

You can listen to equipment (such as a cassette,

MD, or MP3 portable player) connected to the unit.

Refer to the operating instructions for the

corresponding equipment for more detailed

information.

Be sure to remove the inserted CD to prevent

possible damage to the unit before connecting the

equipment.

1 Connect a cassette/MD/MP3 portable player

or other equipment to the unit’s AUX jack

(3.5 mm dia.).

2 Press (SOURCE) repeatedly until “AUX”

appears on the display.

Various settings

To align the sound levels (Source Level

Adjustor)

Volume may vary each time you change the source

mode. In this case, you can align each source

mode’s volume to almost the same level.

1 Select the source mode to be adjusted.

2 Press and hold (SOURCE) until “LEVEL 0”

appears on the display.

3 Turn (PUSH-MENU) to adjust the level.

The volume level is adjustable from –6 to +6 dB

by 1 dB steps.

To change the display and beep tone

settings

You can set the dimmer of the display, and turn on

or off the VU level meter and the beep tone.

Proceed as follows while the unit is turned on.

There are items that cannot be selected if you

operate when the unit is deactivated.

1 Press and hold (PUSH-MENU) until “SET”

appears on the display.

2 Press (SEEK) (+) or (SEEK) (–) to select

“DIM,” “VU” or “BEEP.”

Each time you press (SEEK) (+), the item

changes as follows:

DIM (dimmer) t

VU (VU level meter) t

A.SCRL* t

BEEP (beep tone)

* Auto Scroll, available when source is CD

(page 9)

3 Turn (PUSH-MENU) to change the setting for

the selected item.

To select the type of equipment

connected to the rear panel

You can connect a power amplifier or a sub-woofer

to the AUDIO OUT REAR jacks on the rear of the

unit.

When a power amplifier or a sub-woofer is

connected, select the type of the connected

equipment correctly.

1 While the unit is deactivated (clock or DEMO

is diplayed), press (PUSH-MENU).

2 Turn (PUSH-MENU) to select “REAR” (for a

power amplifier) or “SUB” (for a sub-

woofer).

CARD REMOTE CONTROL

Names of parts

PRESET

–

ATTOFF

DSPL MODE

SOURCE

PRESET

VOL

–

ALBUM

SEEK

–

SEEK

ALBUM –

1 DSPL button

2 SOURCE button

3 SEEK (+/–) buttons

4 OFF button

5 VOL (+/–) buttons

6 MODE button

7 PRESET/ALBUM (+/–) buttons

8 ATT button

Note

If the display disappears by pressing (OFF) , it

cannot be operated with the remote control unless

(SOURCE) on the unit is pressed, or a disc is

inserted to activate the unit first.

Preparations

A lithium battery is installed in the remote control

at the factory.

Before you use the remote control, be sure to

remove the insulating sheet by simply pulling it

out.

Remote control (back)

Insulating sheet

Replacing the battery

1 Insert the tip of a pointed object A into the

hole B and pull out the battery holder to

remove the lithium battery (CR2025).

Remote control (back)

Battery holder

2 Install a new lithium battery (CR2025)* with

the 3 side facing up in the battery holder,

and push the battery holder into the unit

until it clicks.

* Use of any other battery may present a risk of

fire or explosion.

Note

When the infrared receptor on the main unit is

exposed to direct sunlight, it may not respond to

signals from the remote control.

Notes on lithium battery

•Keep the lithium battery out of the reach of

children. Should the battery be swallowed,

immediately consult a doctor.

•Wipe the battery with a dry cloth to assure a

good contact.

•Be sure to observe the correct polarity when

installing the battery.

•Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

WARNING

Battery may explode if mistreated.

Do not recharge, disassemble, or dispose of in

fire.

TROUBLESHOOTING

The following checklist will help you remedy

problems you may encounter with your unit.

Before going through the checklist below, check the

connection and operating procedures.

General

No sound.

•Turn (PUSH-MENU) to the right to adjust the

volume.

•Cancel the ATT function.

•Set the fader control to the center position for a 2-

speaker system.

The contents of the memory have been erased.

•The reset button has been pressed.

t Store again into the memory.

•The power lead or battery has been disconnected.

•The power connecting lead is not connected

properly.

No beep sound.

•The beep sound is canceled (page 10).

•An optional power amplifier is connected and

you are not using the built-in amplifier.

The display disappears from/does not appear

on the display window.

•The display disappears if you press and hold

(OFF).

t Press and hold (OFF) again until the display

appears.

•Remove the front panel and clean the connectors.

See “Cleaning the connectors” (page 16).

Stored stations and correct time are erased.

The fuse has blown.

Makes noise when the ignition key is in the ON,

ACC, or OFF position.

The leads are not matched correctly with the car’s

accessory power connector.

No power is being supplied to the unit.

•Check the connection. If everything is in order,

check the fuse.

•The car does not have an ACC position.

t Press (SOURCE) (or insert a disc) to turn on

the unit.

The power antenna does not extend.

The power antenna does not have a relay box.

Radio reception

Preset tuning is not possible.

•Store the correct frequency in the memory.

•The broadcast signal is too weak.

The stations cannot be received.

The sound is hampered by noises.

•Connect a power antenna control lead (blue) or

accessory power supply lead (red) to the power

supply lead of a car’s antenna booster (only

when your car has built-in FM/AM antenna in

the rear/side glass).

•Check the connection of the car antenna.

•The auto antenna will not go up.

t Check the connection of the power antenna

control lead.

•Check the frequency.

Automatic tuning is not possible.

•The local seek mode is set to “ON.”

t Set the local seek mode to “OFF” (page 7).

•The broadcast signal is too weak.

t Perform manual tuning.

A program broadcast in stereo is heard in

monaural.

t Cancel monaural reception mode (page 7).

CD play

A CD cannot be inserted.

•Another CD is already inserted.

•The CD has been forcibly inserted upside down

or in the wrong way.

Play does not begin.

•Defective or dirty CD

•CD-R/CD-RW that is not finalized.

•Some CD-Rs/CD-RWs may not play due to its

recording equipment or the disc condition.

MP3 files cannot be played back.

•Recording was not performed according to the

ISO 9660 level 1 or level 2 format, or the Joliet or

Romeo in the expansion format.

•The file extension “.MP3” is not added to the file

name.

•Files are not stored in MP3 format.

MP3 files take longer to play back than others.

The following discs take a longer time to start

playback.

–a disc recorded with complicated tree structure.

–a disc recorded in Multi Session.

–a disc to which data can be added.

A disc is automatically ejected.

The ambient temperature exceeds 50˚C (112˚F).

The operation buttons do not function.

CD will not be ejected.

Press the reset button.

The sound skips from vibration.

•The unit is installed at an angle of more than 45˚.

•The unit is not installed in a sturdy part of the

car.

The sound skips.

Dirty or defective disc.

ERROR DISPLAYS/

MESSAGES

Error displays

The following indications will flash for about 5

seconds, and an alarm sound will be heard.

ERROR

•A CD is dirty or inserted upside down.

t Clean or insert the CD correctly.

•A CD cannot play because of some problem.

t Insert another CD.

FAILURE

The connection of speakers/amplifiers is incorrect.

t See the installation guide manual of this

model to check the connection.

HI TEMP

The ambient temperature is more than 50˚C

(112˚F).

t Wait until the temperature goes down below

50˚C (112˚F).

NO MUSIC

A CD which is not a music file is inserted in this

unit.

t Insert a music CD in this unit.

OFFSET

There may be an internal malfunction.

t Check the connection. If the error indication

remains on, consult your nearest Sony dealer.

RESET

The CD unit cannot be operated because of some

problem.

t Press the reset button.

Messages

L.SEEK +/–

The Local Seek mode is on during automatic

tuning (page 7).

“ ” or “ ”

You have reached the beginning or the end of the

disc and you cannot go any further.

If these solutions do not help improve the

situation, consult your nearest Sony dealer.

ADDITIONAL INFORMATION

About MP3 files

MP3 (MPEG 1 Audio Layer-3) is a standard

technology and format for compressing a sound

sequence. The file is compressed to about 1/10 of

its original size. Sounds outside the range of

human hearing are compressed while the sounds

we can hear are not compressed.

Notes on discs

You can play MP3 files recorded on CD-ROMs,

CD-Rs, and CD-RWs.

The disc must be in the ISO 9660

level 1 or level 2

format, or Joliet or Romeo in the expansion format.

You can use a disc recorded in Multi Session

ISO 9660 Format

The most common international standard for the

logical format of files and folders on a CD-ROM.

There are several specification levels. In Level 1,

file names must be in the 8.3 format (no more

than 8 characters in the name, no more than 3

characters in the extension “.MP3”) and in capital

letters. Folder names can be no longer than 8

characters. There can be no more than 8 nested

folder levels. Level 2 specifications allow file

names up to 31 characters long.

Each folder can have up to 8 trees.

For Joliet or Romeo in the expansion format,

make sure of the contents of the writing software,

etc.

Multi Session

This is a recording method that enables adding of

data using the Track-At-Once method.

Conventional CDs begin at a CD control area

called the Lead-in and end at an area called

Lead-out. A Multi Session CD is a CD having

multiple sessions, with each segment from Lead-

in to Lead-out regarded as a single session.

CD-Extra: The format which records audio

(audio CD data) as tracks on session 1, and

records data as tracks on session 2.

Mixed CD: In this format, data is recorded as

track 1, and audio (audio CD data) is recorded as

track 2.

Notes

•With formats other than ISO 9660 level 1 and

level 2, folder names or file names may not be

displayed correctly.

•When naming, be sure to add the file extension

“.MP3” to the file name.

•If you put the extension “.MP3” to a file other

than MP3, the unit cannot recognize the file

properly and will generate random noise that

could damage your speakers.

•The following discs take a longer time to start

playback.

–a disc recorded with complicated tree structure.

–a disc recorded in Multi Session.

–a disc to which data can be added.

Cautions when playing a disc that is recorded in

Multi Session

•When the first track of the first session is audio

CD data:

Only audio CD data of the first session is played

back.

Any data in subsequent sessions is skipped.

•When the first track of the first session is not

audio CD data:

– If an MP3 file is in the disc, only MP3 file(s)

play back and other data is skipped. (Audio CD

data is not recognized.)

– If no MP3 file is in the disc, “NO MUSIC” is

displayed and nothing is played back. (Audio

CD data is not recognized.)

The playback order of the MP3 files

The playback order of the folders and files is as

follows:

Notes

•A folder that does not include an MP3 file is

skipped.

•When you insert a disc with many trees, it takes a

longer time to start playback. We recommend

that you make only one or two trees for each

disc.

•Maximum folder number: 150 (including root

folder and empty folders)

•The maximum number of MP3 files and folders

that can be contained in a disc: 300

When a file/folder name contains many

characters, this number may become less than

300.

•To specify a desired playback order, before the

folder or file name, input the order by number

(e.g., “01,” “02”), then record contents onto a

disc. (The order differs depending on the writing

software.)

Folder (album)

MP3 file (track)

Tree 1

(root)

Tree 2 Tree 3 Tree 4 Tree 5

Maintenance

Cleaning the front panel

Wipe the surface with a soft, dry cloth. Do not use

liquid cleaners or aerosol cleaners.

Cleaning the connectors

The connectors need to be cleaned occasionally.

Wipe the surface of the connectors with a cotton

swab slightly moistened with alcohol.

Main unit

Back of the front panel

Notes

•For safety, turn off the ignition before cleaning

the connectors, and remove the key from the

ignition switch.

•Never touch the connectors directly with your

fingers or with any metal device.

Fuse replacement

When replacing the fuse, be sure to use one

matching the amperage rating stated on the

original fuse. If the fuse blows, check the power

connection and replace the fuse. If the fuse blows

again after replacement, there may be an internal

malfunction. In such a case, consult your nearest

Sony dealer.

Warning

Never use a fuse with an amperage rating

exceeding the one supplied with the unit as this

could damage the unit.

Removing the unit

Remove the protection collar.

1 Detatch the front cover (page 4).

2 Engage the release keys together with the

protection collar.

3 Pull out the release keys to remove the

protection collar.

2 Remove the unit.

1 Insert both release keys together until they

click.

2 Pull the release keys to unseat the unit.

3 Slide the unit out of the mounting.

Orient the release

key correctly.

Face the hook

inwards.

Fuse (10 A)

Specifications

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL

HARMONIC DISTORTION

23.2 watts per channel minimum

continuous average power into 4

ohms, 4 channels driven from 20 Hz

to 20 kHz with no more than 5% total

harmonic distortion.

Tuner section

Tuning range 87.5 - 107.9 MHz

Antenna terminal External antenna connector

Intermediate frequency

10.7 MHz/450 kHz

Usable sensitivity 9 dBf

Selectivity 75 dB at 400 kHz

Signal-to-noise ratio 67 dB (stereo),

69 dB (mono)

Harmonic distortion at 1 kHz

0.5 % (stereo),

0.3 % (mono)

Separation 35 dB at 1 kHz

Frequency response 30 - 15,000 Hz

Tuning range 530 - 1,710 kHz

Antenna terminal External antenna connector

Intermediate frequency

10.7 MHz/450 kHz

Sensitivity 30 µV

CD player section

Signal-to-noise ratio 120 dB

Frequency response 10 - 20,000 Hz

Wow and flutter Below measurable limit

Power amplifier section

Outputs Speaker outputs

(sure seal connectors)

Speaker impedance 4 - 8 ohms

Maximum power output

52 W × 4 (at 4 ohms)

General

Outputs Audio outputs terminal

(rear/sub switchable)

Power antenna relay control

terminal

Power amplifier control

terminal

Inputs Antenna input terminal

Tone controls Low:

±10 dB at 60 Hz (HIP-HOP)

Mid:

±10 dB at 1 kHz (HIP-HOP)

High:

±10 dB at 10 kHz (HIP-HOP)

Power requirements 12 V DC car battery

(negative ground)

Dimensions Approx. 178 × 50 × 176 mm

/8 × 2 × 7 in.)

(w/h/d)

Mounting dimensions

Approx. 182 × 53 × 161 mm

/4 × 2

/8 × 6

/8 in.)

(w/h/d)

Mass Approx. 1.2 kg

(2 lb 10 oz)

Supplied accessories Parts for installation and

connections

Front panel case (1)

Card remote control

RM-Z304

Design and specifications are subject to change

without notice.

Remarques sur les disques

•Pour que le disque reste propre, ne touchez pas

sa surface. Saisissez le disque par les bords.

•Rangez vos disques dans leur boîtier ou dans un

chargeur lorsque vous ne vous en servez pas.

•Ne soumettez pas les disques à des températures

élevées. Evitez de les laisser dans un véhicule en

stationnement, sur le tableau de bord ou la plage

arrière.

•Ne collez pas d’étiquettes sur les disques et

n’utilisez pas de disques rendus collants par de

l’encre ou des résidus. De tels disques peuvent

s’arrêter de tourner en cours de lecture et

provoquer des problèmes de fonctionnement ou

être endommagés.

•N’utilisez pas de disques sur lesquels sont collés

des étiquettes ou des autocollants.

L’utilisation de tels disques peut entraîner les

problèmes suivants :

– impossibilité d’éjecter un disque parce que

l’étiquette ou l’autocollant se décolle et bloque

le mécanisme d’éjection ;

– erreurs de lecture des données audio (par ex.

saut de lecture ou aucune lecture) provoquées

par une déformation du disque suite au

rétrécissement de l’étiquette ou de l’autocollant

sous l’effet de la chaleur.

•Les disques de forme non standard (per ex. : en

forme de cœur, de carré ou d’étoile) ne peuvent

pas être lus avec cet appareil. Vous risquez

d’endommager votre appareil si vous essayez de

le faire. N’utilisez pas de tels disques.

•Cet appareil ne permet pas la lecture des CD de

8 cm (3 po.).

PRECAUTIONS

•Si votre véhicule est resté stationné en plein

soleil, laissez l’appareil refroidir avant de

l’utiliser.

•L’antenne électrique se déploie automatiquement

lorsque l’appareil est en fonctionnement.

Si vous avez des questions ou des problèmes

concernant cet appareil qui ne sont pas abordés

dans ce mode d’emploi, consultez votre revendeur

Sony le plus proche.

Condensation

Par temps de pluie ou dans des régions très

humides, de l’humidité peut se condenser à

l’intérieur des lentilles et dans la fenêtre

d’affichage de l’appareil. Si cela se produit,

l’appareil ne fonctionne pas correctement. Dans ce

cas, retirez le disque et attendez environ une heure

que l’humidité se soit évaporée.

Pour conserver un son de haute qualité

Veillez à ne pas renverser de jus de fruit ou d’autres

boissons sucrées sur l’appareil ou sur les disques.

En ce qui concerne l’installation et les

connexions, consulter le manuel

d’installation/raccordement fourni.

•Avant la lecture, nettoyez

les disques avec un chiffon

de nettoyage disponible

dans le commerce. Essuyez

chaque disque en partant

du centre vers l’extérieur.

N’utilisez pas de solvants

tels que de l’essence, du

diluant, des produits de

nettoyage vendus dans le

commerce ou des sprays

antistatiques destinés aux

disques analogiques.

Disques de musique encodés à l’aide d’une

technologie de protection des droits d’auteur

Cet appareil est conçu pour la lecture des disques

conformes à la norme Compact Disc (CD).

Dernièrement, certaines maisons de disques ont

lancé sur le marché divers types de disques de

musique encodés avec des technologies de

protection des droits d’auteur. Notez que, parmi

ces types de disques, certains ne sont pas

conformes à la norme CD. La lecture de ces

disques peut alors être impossible avec cet

appareil.

Remarques sur les CD-R

(CD enregistrables) et les CD-RW

(CD réinscriptibles)

Cet appareil permet la lecture des types de disques

suivants :

Type de disques Symbole indiqué sur le disque

CD audio

Fichiers MP3

•Il est possible que cet appareil ne puisse pas lire

certains CD-R ou CD-RW (en fonction de

l’appareil utilisé pour l’enregistrement ou de

l’état du disque).

•Ce lecteur ne permet pas la lecture de CD-R ou

de CD-RW non finalisés*.

•Ce lecteur permet la lecture de fichiers MP3

copiés sur des disques CD-ROM, CD-R (CD

enregistrables) et CD-RW (CD réinscriptibles).

•Il est possible de lire des CD-R ou CD-RW

auxquels une session peut être ajoutée.

*Processus nécessaire pour qu’un disque CD-R ou

CD-RW enregistré puisse être lu sur un lecteur

CD audio.

TABLE DES MATIERES

PRÉPARATIFS

Réinitialisation de l’appareil .............................. 4

Mode DEMO (démonstration) .......................... 4

Protection antivol ................................................ 4

FONCTIONNEMENT DE BASE, RÉGLAGE DU

SON ET DE L’HEURE

Mise en marche de l’appareil ............................. 5

Réglage de l’heure ............................................... 5

Réglage du son ..................................................... 5

FONCTIONNEMENT DE LA RADIO

Mémorisation automatique des stations .......... 7

Réception des stations mémorisées .................. 7

Mémorisation manuelle des stations ................ 7

FONCTIONNEMENT DU LECTEUR DE CD

Lecture d’un disque ............................................ 8

Signification de l’affichage ................................. 9

AUTRES FONCTIONS

Utilisation d’un autre appareil ........................ 10

Divers réglages .................................................. 10

MINI-TÉLÉCOMMANDE

Noms des éléments ........................................... 11

Préparatifs........................................................... 11

Remplacement de la pile .................................. 11

DEPANNAGE

Généralités .......................................................... 12

Réception radio .................................................. 12

Lecture de CD .................................................... 13

AFFICHAGE DES ERREURS ET MESSAGES

Affichage des erreurs ........................................ 13

Messages ............................................................. 13

INFORMATIONS COMPLEMENTAIRES

A propos des fichiers MP3 ............................... 14

Entretien.............................................................. 16

Démontage de l’appareil .................................. 16

Spécifications...................................................... 17

PRÉPARATIFS

Remarque

Certaines touches de l’appareil ont plusieurs

fonctions. Pour le détail à ce sujet, reportez-vous

aux pages appropriées.

Réinitialisation de l’appareil

L’appareil doit être réinitialisé la première fois que

vous l’utilisez ou après le remplacement de la

batterie de la voiture ou le changement des

connexions.

Détachez le panneau avant et appuyez sur le

bouton de réinitialisation avec un objet pointu, par

exemple un stylo.

Panneau avant détaché

Bouton de réinitialisation

Remarque

L’heure et les fonctions mémorisées sont

supprimées lorsque vous appuyez sur le bouton de

réinitialisation.

Mode DEMO (démonstration)

Cet appareil présente un mode d’affichage

(DEMO) qui montre les différents modes

d’éclairage.

Lorsque vous arrêtez l’appareil en appuyant sur

(OFF), l’heure est indiquée pendant 10 secondes

environ, puis l’appareil se met en mode DEMO.

Pour annuler le mode DEMO

1 En mode DEMO, appuyez sur (PUSH-MENU)

jusqu’à ce que « SET » apparaisse dans la

fenêtre d’affichage.

2 Appuyez sur (SEEK) (+) ou (SEEK) (–) pour

sélectionner « DEMO ».

3 Tournez (PUSH-MENU) pour sélectionner

« DEMO OFF ».

Pour revenir au mode DEMO, refaites les mêmes

opérations et sélectionnez « DEMO ON » à l’étape

Protection antivol

Emportez le panneau avant et rangez-le dans l’étui

fourni lorsque vous quittez votre voiture.

Avertisseur

Si vous coupez le contact sans enlever le panneau

avant, l’avertisseur bipe pendant quelques

secondes.

Si vous raccordez un amplificateur optionnel et

n’utilisez pas l’amplificateur intégré, l’avertisseur

sera désactivé.

Pour détacher le panneau avant

1 Appuyez sur Z pour retirer le disque.

2 Appuyez sur (OFF)*.

3 Appuyez sur puis tirez sur le panneau.

(Tenez-le d’une main pour l’empêcher de

tomber.)

(OFF)

* Si le commutateur de contact de votre véhicule

n’est pas doté d’une position ACC (accessoires),

veillez à appuyer sur (OFF) jusqu’à ce que

l’affichage disparaisse pour éviter d’user la

batterie du véhicule.

Pour rattacher le panneau avant

1 Emboîtez le côté droit du panneau avant

dans le cliquet droit de l’appareil.

2 Appuyez sur le panneau avant de sorte qu’il

se verrouille.

Attention de ne pas appuyer sur une touche et

sur la fenêtre d’affichage.

Remarques

•Si vous retirez le panneau avant alors que

l’appareil est sous tension, l’alimentation est

automatiquement coupée pour éviter

d’endommager les haut-parleurs.

•N’exposez pas le panneau avant à des

températures élevées ou à l’humidité. Evitez de

le laisser dans un véhicule en stationnement, sur

le tableau de bord ou la plage arrière.

•Ne posez rien sur la face interne du panneau

avant.

La page charge ...

Aiwa cdcx 504mp Le manuel du propriétaire

Marque: Aiwa

Modèle: cdcx 504mp

Catégorie: Récepteurs multimédia de voiture

Taper: Le manuel du propriétaire

Ce manuel convient également à

CDC-X504MP

Télécharger le PDF

rapport

dans d''autres langues

English: Aiwa cdcx 504mp Owner's manual
español: Aiwa cdcx 504mp El manual del propietario

Aiwa cdcx 504mp Le manuel du propriétaire

Ce manuel convient également à

Aiwa cdcx 504mp Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents